diff options
| -rw-r--r-- | Documentation/hwmon/max197 | 60 | ||||
| -rw-r--r-- | drivers/hwmon/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/hwmon/Makefile | 1 | ||||
| -rw-r--r-- | drivers/hwmon/max197.c | 349 | ||||
| -rw-r--r-- | include/linux/platform_data/max197.h | 21 |
5 files changed, 440 insertions, 0 deletions
diff --git a/Documentation/hwmon/max197 b/Documentation/hwmon/max197 new file mode 100644 index 000000000000..8d89b9009df8 --- /dev/null +++ b/Documentation/hwmon/max197 @@ -0,0 +1,60 @@ +Maxim MAX197 driver +=================== + +Author: + * Vivien Didelot <vivien.didelot@savoirfairelinux.com> + +Supported chips: + * Maxim MAX197 + Prefix: 'max197' + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX197.pdf + + * Maxim MAX199 + Prefix: 'max199' + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX199.pdf + +Description +----------- + +The A/D converters MAX197, and MAX199 are both 8-Channel, Multi-Range, 5V, +12-Bit DAS with 8+4 Bus Interface and Fault Protection. + +The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to 10V, +while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199. + +Platform data +------------- + +The MAX197 platform data (defined in linux/platform_data/max197.h) should be +filled with a pointer to a conversion function, defined like: + + int convert(u8 ctrl); + +ctrl is the control byte to write to start a new conversion. +On success, the function must return the 12-bit raw value read from the chip, +or a negative error code otherwise. + +Control byte format: + +Bit Name Description +7,6 PD1,PD0 Clock and Power-Down modes +5 ACQMOD Internal or External Controlled Acquisition +4 RNG Full-scale voltage magnitude at the input +3 BIP Unipolar or Bipolar conversion mode +2,1,0 A2,A1,A0 Channel + +Sysfs interface +--------------- + +* in[0-7]_input: The conversion value for the corresponding channel. + RO + +* in[0-7]_min: The lower limit (in mV) for the corresponding channel. + For the MAX197, it will be adjusted to -10000, -5000, or 0. + For the MAX199, it will be adjusted to -4000, -2000, or 0. + RW + +* in[0-7]_max: The higher limit (in mV) for the corresponding channel. + For the MAX197, it will be adjusted to 0, 5000, or 10000. + For the MAX199, it will be adjusted to 0, 2000, or 4000. + RW diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index f50cb440575d..6566ed6db3b0 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -813,6 +813,15 @@ config SENSORS_MAX1668 This driver can also be built as a module. If so, the module will be called max1668. +config SENSORS_MAX197 + tristate "Maxim MAX197 and compatibles" + help + Support for the Maxim MAX197 A/D converter. + Support will include, but not be limited to, MAX197, and MAX199. + + This driver can also be built as a module. If so, the module + will be called max197. + config SENSORS_MAX6639 tristate "Maxim MAX6639 sensor chip" depends on I2C && EXPERIMENTAL diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 8b3d4382f61e..a62ce17ddbfc 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -95,6 +95,7 @@ obj-$(CONFIG_SENSORS_MAX1111) += max1111.o obj-$(CONFIG_SENSORS_MAX16065) += max16065.o obj-$(CONFIG_SENSORS_MAX1619) += max1619.o obj-$(CONFIG_SENSORS_MAX1668) += max1668.o +obj-$(CONFIG_SENSORS_MAX197) += max197.o obj-$(CONFIG_SENSORS_MAX6639) += max6639.o obj-$(CONFIG_SENSORS_MAX6642) += max6642.o obj-$(CONFIG_SENSORS_MAX6650) += max6650.o diff --git a/drivers/hwmon/max197.c b/drivers/hwmon/max197.c new file mode 100644 index 000000000000..6304f2616fa7 --- /dev/null +++ b/drivers/hwmon/max197.c @@ -0,0 +1,349 @@ +/* + * Maxim MAX197 A/D Converter driver + * + * Copyright (c) 2012 Savoir-faire Linux Inc. + * Vivien Didelot <vivien.didelot@savoirfairelinux.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * For further information, see the Documentation/hwmon/max197 file. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/mutex.h> +#include <linux/device.h> +#include <linux/sysfs.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/platform_device.h> +#include <linux/platform_data/max197.h> + +#define MAX199_LIMIT 4000 /* 4V */ +#define MAX197_LIMIT 10000 /* 10V */ + +#define MAX197_NUM_CH 8 /* 8 Analog Input Channels */ + +/* Control byte format */ +#define MAX197_BIP (1 << 3) /* Bipolarity */ +#define MAX197_RNG (1 << 4) /* Full range */ + +#define MAX197_SCALE 12207 /* Scale coefficient for raw data */ + +/* List of supported chips */ +enum max197_chips { max197, max199 }; + +/** + * struct max197_data - device instance specific data + * @pdata: Platform data. + * @hwmon_dev: The hwmon device. + * @lock: Read/Write mutex. + * @limit: Max range value (10V for MAX197, 4V for MAX199). + * @scale: Need to scale. + * @ctrl_bytes: Channels control byte. + */ +struct max197_data { + struct max197_platform_data *pdata; + struct device *hwmon_dev; + struct mutex lock; + int limit; + bool scale; + u8 ctrl_bytes[MAX197_NUM_CH]; +}; + +static inline void max197_set_unipolarity(struct max197_data *data, int channel) +{ + data->ctrl_bytes[channel] &= ~MAX197_BIP; +} + +static inline void max197_set_bipolarity(struct max197_data *data, int channel) +{ + data->ctrl_bytes[channel] |= MAX197_BIP; +} + +static inline void max197_set_half_range(struct max197_data *data, int channel) +{ + data->ctrl_bytes[channel] &= ~MAX197_RNG; +} + +static inline void max197_set_full_range(struct max197_data *data, int channel) +{ + data->ctrl_bytes[channel] |= MAX197_RNG; +} + +static inline bool max197_is_bipolar(struct max197_data *data, int channel) +{ + return data->ctrl_bytes[channel] & MAX197_BIP; +} + +static inline bool max197_is_full_range(struct max197_data *data, int channel) +{ + return data->ctrl_bytes[channel] & MAX197_RNG; +} + +/* Function called on read access on in{0,1,2,3,4,5,6,7}_{min,max} */ +static ssize_t max197_show_range(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + struct max197_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + int channel = attr->index; + bool is_min = attr->nr; + int range; + + if (mutex_lock_interruptible(&data->lock)) + return -ERESTARTSYS; + + range = max197_is_full_range(data, channel) ? + data->limit : data->limit / 2; + if (is_min) { + if (max197_is_bipolar(data, channel)) + range = -range; + else + range = 0; + } + + mutex_unlock(&data->lock); + + return sprintf(buf, "%d\n", range); +} + +/* Function called on write access on in{0,1,2,3,4,5,6,7}_{min,max} */ +static ssize_t max197_store_range(struct device *dev, + struct device_attribute *devattr, + const char *buf, size_t count) +{ + struct max197_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + int channel = attr->index; + bool is_min = attr->nr; + long value; + int half = data->limit / 2; + int full = data->limit; + + if (kstrtol(buf, 10, &value)) + return -EINVAL; + + if (is_min) { + if (value <= -full) + value = -full; + else if (value < 0) + value = -half; + else + value = 0; + } else { + if (value >= full) + value = full; + else + value = half; + } + + if (mutex_lock_interruptible(&data->lock)) + return -ERESTARTSYS; + + if (value == 0) { + /* We can deduce only the polarity */ + max197_set_unipolarity(data, channel); + } else if (value == -half) { + max197_set_bipolarity(data, channel); + max197_set_half_range(data, channel); + } else if (value == -full) { + max197_set_bipolarity(data, channel); + max197_set_full_range(data, channel); + } else if (value == half) { + /* We can deduce only the range */ + max197_set_half_range(data, channel); + } else if (value == full) { + /* We can deduce only the range */ + max197_set_full_range(data, channel); + } + + mutex_unlock(&data->lock); + + return count; +} + +/* Function called on read access on in{0,1,2,3,4,5,6,7}_input */ +static ssize_t max197_show_input(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct max197_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int channel = attr->index; + s32 value; + int ret; + + if (mutex_lock_interruptible(&data->lock)) + return -ERESTARTSYS; + + ret = data->pdata->convert(data->ctrl_bytes[channel]); + if (ret < 0) { + dev_err(dev, "conversion failed\n"); + goto unlock; + } + value = ret; + + /* + * Coefficient to apply on raw value. + * See Table 1. Full Scale and Zero Scale in the MAX197 datasheet. + */ + if (data->scale) { + value *= MAX197_SCALE; + if (max197_is_full_range(data, channel)) + value *= 2; + value /= 10000; + } + + ret = sprintf(buf, "%d\n", value); + +unlock: + mutex_unlock(&data->lock); + return ret; +} + +static ssize_t max197_show_name(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct platform_device *pdev = to_platform_device(dev); + return sprintf(buf, "%s\n", pdev->name); +} + +#define MAX197_SENSOR_DEVICE_ATTR_CH(chan) \ + static SENSOR_DEVICE_ATTR(in##chan##_input, S_IRUGO, \ + max197_show_input, NULL, chan); \ + static SENSOR_DEVICE_ATTR_2(in##chan##_min, S_IRUGO | S_IWUSR, \ + max197_show_range, \ + max197_store_range, \ + true, chan); \ + static SENSOR_DEVICE_ATTR_2(in##chan##_max, S_IRUGO | S_IWUSR, \ + max197_show_range, \ + max197_store_range, \ + false, chan) + +#define MAX197_SENSOR_DEV_ATTR_IN(chan) \ + &sensor_dev_attr_in##chan##_input.dev_attr.attr, \ + &sensor_dev_attr_in##chan##_max.dev_attr.attr, \ + &sensor_dev_attr_in##chan##_min.dev_attr.attr + +static DEVICE_ATTR(name, S_IRUGO, max197_show_name, NULL); + +MAX197_SENSOR_DEVICE_ATTR_CH(0); +MAX197_SENSOR_DEVICE_ATTR_CH(1); +MAX197_SENSOR_DEVICE_ATTR_CH(2); +MAX197_SENSOR_DEVICE_ATTR_CH(3); +MAX197_SENSOR_DEVICE_ATTR_CH(4); +MAX197_SENSOR_DEVICE_ATTR_CH(5); +MAX197_SENSOR_DEVICE_ATTR_CH(6); +MAX197_SENSOR_DEVICE_ATTR_CH(7); + +static const struct attribute_group max197_sysfs_group = { + .attrs = (struct attribute *[]) { + &dev_attr_name.attr, + MAX197_SENSOR_DEV_ATTR_IN(0), + MAX197_SENSOR_DEV_ATTR_IN(1), + MAX197_SENSOR_DEV_ATTR_IN(2), + MAX197_SENSOR_DEV_ATTR_IN(3), + MAX197_SENSOR_DEV_ATTR_IN(4), + MAX197_SENSOR_DEV_ATTR_IN(5), + MAX197_SENSOR_DEV_ATTR_IN(6), + MAX197_SENSOR_DEV_ATTR_IN(7), + NULL + }, +}; + +static int __devinit max197_probe(struct platform_device *pdev) +{ + int ch, ret; + struct max197_data *data; + struct max197_platform_data *pdata = pdev->dev.platform_data; + enum max197_chips chip = platform_get_device_id(pdev)->driver_data; + + if (pdata == NULL) { + dev_err(&pdev->dev, "no platform data supplied\n"); + return -EINVAL; + } + + if (pdata->convert == NULL) { + dev_err(&pdev->dev, "no convert function supplied\n"); + return -EINVAL; + } + + data = devm_kzalloc(&pdev->dev, sizeof(struct max197_data), GFP_KERNEL); + if (!data) { + dev_err(&pdev->dev, "devm_kzalloc failed\n"); + return -ENOMEM; + } + + data->pdata = pdata; + mutex_init(&data->lock); + + if (chip == max197) { + data->limit = MAX197_LIMIT; + data->scale = true; + } else { + data->limit = MAX199_LIMIT; + data->scale = false; + } + + for (ch = 0; ch < MAX197_NUM_CH; ch++) + data->ctrl_bytes[ch] = (u8) ch; + + platform_set_drvdata(pdev, data); + + ret = sysfs_create_group(&pdev->dev.kobj, &max197_sysfs_group); + if (ret) { + dev_err(&pdev->dev, "sysfs create group failed\n"); + return ret; + } + + data->hwmon_dev = hwmon_device_register(&pdev->dev); + if (IS_ERR(data->hwmon_dev)) { + ret = PTR_ERR(data->hwmon_dev); + dev_err(&pdev->dev, "hwmon device register failed\n"); + goto error; + } + + return 0; + +error: + sysfs_remove_group(&pdev->dev.kobj, &max197_sysfs_group); + return ret; +} + +static int __devexit max197_remove(struct platform_device *pdev) +{ + struct max197_data *data = platform_get_drvdata(pdev); + + hwmon_device_unregister(data->hwmon_dev); + sysfs_remove_group(&pdev->dev.kobj, &max197_sysfs_group); + + return 0; +} + +static struct platform_device_id max197_device_ids[] = { + { "max197", max197 }, + { "max199", max199 }, + { } +}; +MODULE_DEVICE_TABLE(platform, max197_device_ids); + +static struct platform_driver max197_driver = { + .driver = { + .name = "max197", + .owner = THIS_MODULE, + }, + .probe = max197_probe, + .remove = __devexit_p(max197_remove), + .id_table = max197_device_ids, +}; +module_platform_driver(max197_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Savoir-faire Linux Inc. <kernel@savoirfairelinux.com>"); +MODULE_DESCRIPTION("Maxim MAX197 A/D Converter driver"); diff --git a/include/linux/platform_data/max197.h b/include/linux/platform_data/max197.h new file mode 100644 index 000000000000..e2a41dd7690c --- /dev/null +++ b/include/linux/platform_data/max197.h @@ -0,0 +1,21 @@ +/* + * Maxim MAX197 A/D Converter Driver + * + * Copyright (c) 2012 Savoir-faire Linux Inc. + * Vivien Didelot <vivien.didelot@savoirfairelinux.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * For further information, see the Documentation/hwmon/max197 file. + */ + +/** + * struct max197_platform_data - MAX197 connectivity info + * @convert: Function used to start a conversion with control byte ctrl. + * It must return the raw data, or a negative error code. + */ +struct max197_platform_data { + int (*convert)(u8 ctrl); +}; |