diff options
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_82575.c | 12 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/igb/igb_main.c | 4 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/ixgbe/ixgbe.h | 3 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 42 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 300 |
5 files changed, 250 insertions, 111 deletions
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c index b13b42e5a1d9..a795c07d0df7 100644 --- a/drivers/net/ethernet/intel/igb/e1000_82575.c +++ b/drivers/net/ethernet/intel/igb/e1000_82575.c @@ -225,19 +225,7 @@ static s32 igb_init_phy_params_82575(struct e1000_hw *hw) hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT; - /* Make sure the PHY is in a good state. Several people have reported - * firmware leaving the PHY's page select register set to something - * other than the default of zero, which causes the PHY ID read to - * access something other than the intended register. - */ - ret_val = hw->phy.ops.reset(hw); - if (ret_val) { - hw_dbg("Error resetting the PHY.\n"); - goto out; - } - /* Set phy->phy_addr and phy->id. */ - igb_write_phy_reg_82580(hw, I347AT4_PAGE_SELECT, 0); ret_val = igb_get_phy_id_82575(hw); if (ret_val) return ret_val; diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c index e3a0c02721c9..25720d95d4ea 100644 --- a/drivers/net/ethernet/intel/igb/igb_main.c +++ b/drivers/net/ethernet/intel/igb/igb_main.c @@ -6031,7 +6031,7 @@ static int igb_tx_map(struct igb_ring *tx_ring, * We also need this memory barrier to make certain all of the * status bits have been updated before next_to_watch is written. */ - wmb(); + dma_wmb(); /* set next_to_watch value indicating a packet is present */ first->next_to_watch = tx_desc; @@ -8531,7 +8531,7 @@ void igb_alloc_rx_buffers(struct igb_ring *rx_ring, u16 cleaned_count) * applicable for weak-ordered memory model archs, * such as IA-64). */ - wmb(); + dma_wmb(); writel(i, rx_ring->tail); } } diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe.h b/drivers/net/ethernet/intel/ixgbe/ixgbe.h index 144d5fe6b944..4fc906c6166b 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe.h +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe.h @@ -855,7 +855,8 @@ void ixgbe_free_rx_resources(struct ixgbe_ring *); void ixgbe_free_tx_resources(struct ixgbe_ring *); void ixgbe_configure_rx_ring(struct ixgbe_adapter *, struct ixgbe_ring *); void ixgbe_configure_tx_ring(struct ixgbe_adapter *, struct ixgbe_ring *); -void ixgbe_disable_rx_queue(struct ixgbe_adapter *adapter, struct ixgbe_ring *); +void ixgbe_disable_rx(struct ixgbe_adapter *adapter); +void ixgbe_disable_tx(struct ixgbe_adapter *adapter); void ixgbe_update_stats(struct ixgbe_adapter *adapter); int ixgbe_init_interrupt_scheme(struct ixgbe_adapter *adapter); bool ixgbe_wol_supported(struct ixgbe_adapter *adapter, u16 device_id, diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c index bd1ba88ec1d5..e5a8461fe6a9 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c @@ -511,7 +511,7 @@ static void ixgbe_set_msglevel(struct net_device *netdev, u32 data) static int ixgbe_get_regs_len(struct net_device *netdev) { -#define IXGBE_REGS_LEN 1139 +#define IXGBE_REGS_LEN 1145 return IXGBE_REGS_LEN * sizeof(u32); } @@ -874,6 +874,14 @@ static void ixgbe_get_regs(struct net_device *netdev, /* X540 specific DCB registers */ regs_buff[1137] = IXGBE_READ_REG(hw, IXGBE_RTTQCNCR); regs_buff[1138] = IXGBE_READ_REG(hw, IXGBE_RTTQCNTG); + + /* Security config registers */ + regs_buff[1139] = IXGBE_READ_REG(hw, IXGBE_SECTXCTRL); + regs_buff[1140] = IXGBE_READ_REG(hw, IXGBE_SECTXSTAT); + regs_buff[1141] = IXGBE_READ_REG(hw, IXGBE_SECTXBUFFAF); + regs_buff[1142] = IXGBE_READ_REG(hw, IXGBE_SECTXMINIFG); + regs_buff[1143] = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL); + regs_buff[1144] = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT); } static int ixgbe_get_eeprom_len(struct net_device *netdev) @@ -1690,35 +1698,17 @@ static int ixgbe_intr_test(struct ixgbe_adapter *adapter, u64 *data) static void ixgbe_free_desc_rings(struct ixgbe_adapter *adapter) { - struct ixgbe_ring *tx_ring = &adapter->test_tx_ring; - struct ixgbe_ring *rx_ring = &adapter->test_rx_ring; - struct ixgbe_hw *hw = &adapter->hw; - u32 reg_ctl; - - /* shut down the DMA engines now so they can be reinitialized later */ + /* Shut down the DMA engines now so they can be reinitialized later, + * since the test rings and normally used rings should overlap on + * queue 0 we can just use the standard disable Rx/Tx calls and they + * will take care of disabling the test rings for us. + */ /* first Rx */ - hw->mac.ops.disable_rx(hw); - ixgbe_disable_rx_queue(adapter, rx_ring); + ixgbe_disable_rx(adapter); /* now Tx */ - reg_ctl = IXGBE_READ_REG(hw, IXGBE_TXDCTL(tx_ring->reg_idx)); - reg_ctl &= ~IXGBE_TXDCTL_ENABLE; - IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(tx_ring->reg_idx), reg_ctl); - - switch (hw->mac.type) { - case ixgbe_mac_82599EB: - case ixgbe_mac_X540: - case ixgbe_mac_X550: - case ixgbe_mac_X550EM_x: - case ixgbe_mac_x550em_a: - reg_ctl = IXGBE_READ_REG(hw, IXGBE_DMATXCTL); - reg_ctl &= ~IXGBE_DMATXCTL_TE; - IXGBE_WRITE_REG(hw, IXGBE_DMATXCTL, reg_ctl); - break; - default: - break; - } + ixgbe_disable_tx(adapter); ixgbe_reset(adapter); diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index 5a6600f7b382..447098005490 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -4022,38 +4022,6 @@ static void ixgbe_rx_desc_queue_enable(struct ixgbe_adapter *adapter, } } -void ixgbe_disable_rx_queue(struct ixgbe_adapter *adapter, - struct ixgbe_ring *ring) -{ - struct ixgbe_hw *hw = &adapter->hw; - int wait_loop = IXGBE_MAX_RX_DESC_POLL; - u32 rxdctl; - u8 reg_idx = ring->reg_idx; - - if (ixgbe_removed(hw->hw_addr)) - return; - rxdctl = IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx)); - rxdctl &= ~IXGBE_RXDCTL_ENABLE; - - /* write value back with RXDCTL.ENABLE bit cleared */ - IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(reg_idx), rxdctl); - - if (hw->mac.type == ixgbe_mac_82598EB && - !(IXGBE_READ_REG(hw, IXGBE_LINKS) & IXGBE_LINKS_UP)) - return; - - /* the hardware may take up to 100us to really disable the rx queue */ - do { - udelay(10); - rxdctl = IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx)); - } while (--wait_loop && (rxdctl & IXGBE_RXDCTL_ENABLE)); - - if (!wait_loop) { - e_err(drv, "RXDCTL.ENABLE on Rx queue %d not cleared within " - "the polling period\n", reg_idx); - } -} - void ixgbe_configure_rx_ring(struct ixgbe_adapter *adapter, struct ixgbe_ring *ring) { @@ -4063,9 +4031,13 @@ void ixgbe_configure_rx_ring(struct ixgbe_adapter *adapter, u32 rxdctl; u8 reg_idx = ring->reg_idx; - /* disable queue to avoid issues while updating state */ + /* disable queue to avoid use of these values while updating state */ rxdctl = IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx)); - ixgbe_disable_rx_queue(adapter, ring); + rxdctl &= ~IXGBE_RXDCTL_ENABLE; + + /* write value back with RXDCTL.ENABLE bit cleared */ + IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(reg_idx), rxdctl); + IXGBE_WRITE_FLUSH(hw); IXGBE_WRITE_REG(hw, IXGBE_RDBAL(reg_idx), (rdba & DMA_BIT_MASK(32))); IXGBE_WRITE_REG(hw, IXGBE_RDBAH(reg_idx), (rdba >> 32)); @@ -5633,6 +5605,212 @@ void ixgbe_up(struct ixgbe_adapter *adapter) ixgbe_up_complete(adapter); } +static unsigned long ixgbe_get_completion_timeout(struct ixgbe_adapter *adapter) +{ + u16 devctl2; + + pcie_capability_read_word(adapter->pdev, PCI_EXP_DEVCTL2, &devctl2); + + switch (devctl2 & IXGBE_PCIDEVCTRL2_TIMEO_MASK) { + case IXGBE_PCIDEVCTRL2_17_34s: + case IXGBE_PCIDEVCTRL2_4_8s: + /* For now we cap the upper limit on delay to 2 seconds + * as we end up going up to 34 seconds of delay in worst + * case timeout value. + */ + case IXGBE_PCIDEVCTRL2_1_2s: + return 2000000ul; /* 2.0 s */ + case IXGBE_PCIDEVCTRL2_260_520ms: + return 520000ul; /* 520 ms */ + case IXGBE_PCIDEVCTRL2_65_130ms: + return 130000ul; /* 130 ms */ + case IXGBE_PCIDEVCTRL2_16_32ms: + return 32000ul; /* 32 ms */ + case IXGBE_PCIDEVCTRL2_1_2ms: + return 2000ul; /* 2 ms */ + case IXGBE_PCIDEVCTRL2_50_100us: + return 100ul; /* 100 us */ + case IXGBE_PCIDEVCTRL2_16_32ms_def: + return 32000ul; /* 32 ms */ + default: + break; + } + + /* We shouldn't need to hit this path, but just in case default as + * though completion timeout is not supported and support 32ms. + */ + return 32000ul; +} + +void ixgbe_disable_rx(struct ixgbe_adapter *adapter) +{ + unsigned long wait_delay, delay_interval; + struct ixgbe_hw *hw = &adapter->hw; + int i, wait_loop; + u32 rxdctl; + + /* disable receives */ + hw->mac.ops.disable_rx(hw); + + if (ixgbe_removed(hw->hw_addr)) + return; + + /* disable all enabled Rx queues */ + for (i = 0; i < adapter->num_rx_queues; i++) { + struct ixgbe_ring *ring = adapter->rx_ring[i]; + u8 reg_idx = ring->reg_idx; + + rxdctl = IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx)); + rxdctl &= ~IXGBE_RXDCTL_ENABLE; + rxdctl |= IXGBE_RXDCTL_SWFLSH; + + /* write value back with RXDCTL.ENABLE bit cleared */ + IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(reg_idx), rxdctl); + } + + /* RXDCTL.EN may not change on 82598 if link is down, so skip it */ + if (hw->mac.type == ixgbe_mac_82598EB && + !(IXGBE_READ_REG(hw, IXGBE_LINKS) & IXGBE_LINKS_UP)) + return; + + /* Determine our minimum delay interval. We will increase this value + * with each subsequent test. This way if the device returns quickly + * we should spend as little time as possible waiting, however as + * the time increases we will wait for larger periods of time. + * + * The trick here is that we increase the interval using the + * following pattern: 1x 3x 5x 7x 9x 11x 13x 15x 17x 19x. The result + * of that wait is that it totals up to 100x whatever interval we + * choose. Since our minimum wait is 100us we can just divide the + * total timeout by 100 to get our minimum delay interval. + */ + delay_interval = ixgbe_get_completion_timeout(adapter) / 100; + + wait_loop = IXGBE_MAX_RX_DESC_POLL; + wait_delay = delay_interval; + + while (wait_loop--) { + usleep_range(wait_delay, wait_delay + 10); + wait_delay += delay_interval * 2; + rxdctl = 0; + + /* OR together the reading of all the active RXDCTL registers, + * and then test the result. We need the disable to complete + * before we start freeing the memory and invalidating the + * DMA mappings. + */ + for (i = 0; i < adapter->num_rx_queues; i++) { + struct ixgbe_ring *ring = adapter->rx_ring[i]; + u8 reg_idx = ring->reg_idx; + + rxdctl |= IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx)); + } + + if (!(rxdctl & IXGBE_RXDCTL_ENABLE)) + return; + } + + e_err(drv, + "RXDCTL.ENABLE for one or more queues not cleared within the polling period\n"); +} + +void ixgbe_disable_tx(struct ixgbe_adapter *adapter) +{ + unsigned long wait_delay, delay_interval; + struct ixgbe_hw *hw = &adapter->hw; + int i, wait_loop; + u32 txdctl; + + if (ixgbe_removed(hw->hw_addr)) + return; + + /* disable all enabled Tx queues */ + for (i = 0; i < adapter->num_tx_queues; i++) { + struct ixgbe_ring *ring = adapter->tx_ring[i]; + u8 reg_idx = ring->reg_idx; + + IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(reg_idx), IXGBE_TXDCTL_SWFLSH); + } + + /* disable all enabled XDP Tx queues */ + for (i = 0; i < adapter->num_xdp_queues; i++) { + struct ixgbe_ring *ring = adapter->xdp_ring[i]; + u8 reg_idx = ring->reg_idx; + + IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(reg_idx), IXGBE_TXDCTL_SWFLSH); + } + + /* If the link is not up there shouldn't be much in the way of + * pending transactions. Those that are left will be flushed out + * when the reset logic goes through the flush sequence to clean out + * the pending Tx transactions. + */ + if (!(IXGBE_READ_REG(hw, IXGBE_LINKS) & IXGBE_LINKS_UP)) + goto dma_engine_disable; + + /* Determine our minimum delay interval. We will increase this value + * with each subsequent test. This way if the device returns quickly + * we should spend as little time as possible waiting, however as + * the time increases we will wait for larger periods of time. + * + * The trick here is that we increase the interval using the + * following pattern: 1x 3x 5x 7x 9x 11x 13x 15x 17x 19x. The result + * of that wait is that it totals up to 100x whatever interval we + * choose. Since our minimum wait is 100us we can just divide the + * total timeout by 100 to get our minimum delay interval. + */ + delay_interval = ixgbe_get_completion_timeout(adapter) / 100; + + wait_loop = IXGBE_MAX_RX_DESC_POLL; + wait_delay = delay_interval; + + while (wait_loop--) { + usleep_range(wait_delay, wait_delay + 10); + wait_delay += delay_interval * 2; + txdctl = 0; + + /* OR together the reading of all the active TXDCTL registers, + * and then test the result. We need the disable to complete + * before we start freeing the memory and invalidating the + * DMA mappings. + */ + for (i = 0; i < adapter->num_tx_queues; i++) { + struct ixgbe_ring *ring = adapter->tx_ring[i]; + u8 reg_idx = ring->reg_idx; + + txdctl |= IXGBE_READ_REG(hw, IXGBE_TXDCTL(reg_idx)); + } + for (i = 0; i < adapter->num_xdp_queues; i++) { + struct ixgbe_ring *ring = adapter->xdp_ring[i]; + u8 reg_idx = ring->reg_idx; + + txdctl |= IXGBE_READ_REG(hw, IXGBE_TXDCTL(reg_idx)); + } + + if (!(txdctl & IXGBE_TXDCTL_ENABLE)) + goto dma_engine_disable; + } + + e_err(drv, + "TXDCTL.ENABLE for one or more queues not cleared within the polling period\n"); + +dma_engine_disable: + /* Disable the Tx DMA engine on 82599 and later MAC */ + switch (hw->mac.type) { + case ixgbe_mac_82599EB: + case ixgbe_mac_X540: + case ixgbe_mac_X550: + case ixgbe_mac_X550EM_x: + case ixgbe_mac_x550em_a: + IXGBE_WRITE_REG(hw, IXGBE_DMATXCTL, + (IXGBE_READ_REG(hw, IXGBE_DMATXCTL) & + ~IXGBE_DMATXCTL_TE)); + /* fall through */ + default: + break; + } +} + void ixgbe_reset(struct ixgbe_adapter *adapter) { struct ixgbe_hw *hw = &adapter->hw; @@ -5814,24 +5992,19 @@ void ixgbe_down(struct ixgbe_adapter *adapter) if (test_and_set_bit(__IXGBE_DOWN, &adapter->state)) return; /* do nothing if already down */ - /* disable receives */ - hw->mac.ops.disable_rx(hw); + /* Shut off incoming Tx traffic */ + netif_tx_stop_all_queues(netdev); - /* disable all enabled rx queues */ - for (i = 0; i < adapter->num_rx_queues; i++) - /* this call also flushes the previous write */ - ixgbe_disable_rx_queue(adapter, adapter->rx_ring[i]); + /* call carrier off first to avoid false dev_watchdog timeouts */ + netif_carrier_off(netdev); + netif_tx_disable(netdev); - usleep_range(10000, 20000); + /* Disable Rx */ + ixgbe_disable_rx(adapter); /* synchronize_sched() needed for pending XDP buffers to drain */ if (adapter->xdp_ring[0]) synchronize_sched(); - netif_tx_stop_all_queues(netdev); - - /* call carrier off first to avoid false dev_watchdog timeouts */ - netif_carrier_off(netdev); - netif_tx_disable(netdev); ixgbe_irq_disable(adapter); @@ -5859,30 +6032,7 @@ void ixgbe_down(struct ixgbe_adapter *adapter) } /* disable transmits in the hardware now that interrupts are off */ - for (i = 0; i < adapter->num_tx_queues; i++) { - u8 reg_idx = adapter->tx_ring[i]->reg_idx; - IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(reg_idx), IXGBE_TXDCTL_SWFLSH); - } - for (i = 0; i < adapter->num_xdp_queues; i++) { - u8 reg_idx = adapter->xdp_ring[i]->reg_idx; - - IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(reg_idx), IXGBE_TXDCTL_SWFLSH); - } - - /* Disable the Tx DMA engine on 82599 and later MAC */ - switch (hw->mac.type) { - case ixgbe_mac_82599EB: - case ixgbe_mac_X540: - case ixgbe_mac_X550: - case ixgbe_mac_X550EM_x: - case ixgbe_mac_x550em_a: - IXGBE_WRITE_REG(hw, IXGBE_DMATXCTL, - (IXGBE_READ_REG(hw, IXGBE_DMATXCTL) & - ~IXGBE_DMATXCTL_TE)); - break; - default: - break; - } + ixgbe_disable_tx(adapter); if (!pci_channel_offline(adapter->pdev)) ixgbe_reset(adapter); @@ -6469,6 +6619,11 @@ static int ixgbe_change_mtu(struct net_device *netdev, int new_mtu) { struct ixgbe_adapter *adapter = netdev_priv(netdev); + if (adapter->xdp_prog) { + e_warn(probe, "MTU cannot be changed while XDP program is loaded\n"); + return -EPERM; + } + /* * For 82599EB we cannot allow legacy VFs to enable their receive * paths when MTU greater than 1500 is configured. So display a @@ -9407,6 +9562,11 @@ static netdev_features_t ixgbe_fix_features(struct net_device *netdev, if (!(adapter->flags2 & IXGBE_FLAG2_RSC_CAPABLE)) features &= ~NETIF_F_LRO; + if (adapter->xdp_prog && (features & NETIF_F_LRO)) { + e_dev_err("LRO is not supported with XDP\n"); + features &= ~NETIF_F_LRO; + } + return features; } |