diff options
| -rw-r--r-- | Documentation/hwmon/w83627ehf | 54 | ||||
| -rw-r--r-- | drivers/hwmon/w83627ehf.c | 54 |
2 files changed, 90 insertions, 18 deletions
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf index 8a15a7408753..030fac6cec7a 100644 --- a/Documentation/hwmon/w83627ehf +++ b/Documentation/hwmon/w83627ehf @@ -2,26 +2,29 @@ Kernel driver w83627ehf ======================= Supported chips: - * Winbond W83627EHF/EHG (ISA access ONLY) + * Winbond W83627EHF/EHG/DHG (ISA access ONLY) Prefix: 'w83627ehf' Addresses scanned: ISA address retrieved from Super I/O registers - Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83627EHF_%20W83627EHGb.pdf + Datasheet: + http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83627EHF_%20W83627EHGb.pdf + DHG datasheet confidential. Authors: Jean Delvare <khali@linux-fr.org> Yuan Mu (Winbond) Rudolf Marek <r.marek@assembler.cz> + David Hubbard <david.c.hubbard@gmail.com> Description ----------- -This driver implements support for the Winbond W83627EHF and W83627EHG -super I/O chips. We will refer to them collectively as Winbond chips. +This driver implements support for the Winbond W83627EHF, W83627EHG, and +W83627DHG super I/O chips. We will refer to them collectively as Winbond chips. The chips implement three temperature sensors, five fan rotation -speed sensors, ten analog voltage sensors, alarms with beep warnings (control -unimplemented), and some automatic fan regulation strategies (plus manual -fan control mode). +speed sensors, ten analog voltage sensors (only nine for the 627DHG), alarms +with beep warnings (control unimplemented), and some automatic fan regulation +strategies (plus manual fan control mode). Temperatures are measured in degrees Celsius and measurement resolution is 1 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when @@ -55,6 +58,9 @@ prog -> pwm4 (the programmable setting is not supported by the driver) /sys files ---------- +name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG, + it is set to "w83627ehf" and for the W83627DHG it is set to "w83627dhg" + pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range: 0 (stop) to 255 (full) @@ -83,3 +89,37 @@ pwm[1-4]_stop_time - how many milliseconds [ms] must elapse to switch Note: last two functions are influenced by other control bits, not yet exported by the driver, so a change might not have any effect. + +Implementation Details +---------------------- + +Future driver development should bear in mind that the following registers have +different functions on the 627EHF and the 627DHG. Some registers also have +different power-on default values, but BIOS should already be loading +appropriate defaults. Note that bank selection must be performed as is currently +done in the driver for all register addresses. + +0x49: only on DHG, selects temperature source for AUX fan, CPU fan0 +0x4a: not completely documented for the EHF and the DHG documentation assigns + different behavior to bits 7 and 6, including extending the temperature + input selection to SmartFan I, not just SmartFan III. Testing on the EHF + will reveal whether they are compatible or not. + +0x58: Chip ID: 0xa1=EHF 0xc1=DHG +0x5e: only on DHG, has bits to enable "current mode" temperature detection and + critical temperature protection +0x45b: only on EHF, bit 3, vin4 alarm (EHF supports 10 inputs, only 9 on DHG) +0x552: only on EHF, vin4 +0x558: only on EHF, vin4 high limit +0x559: only on EHF, vin4 low limit +0x6b: only on DHG, SYS fan critical temperature +0x6c: only on DHG, CPU fan0 critical temperature +0x6d: only on DHG, AUX fan critical temperature +0x6e: only on DHG, CPU fan1 critical temperature + +0x50-0x55 and 0x650-0x657 are marked "Test Register" for the EHF, but "Reserved + Register" for the DHG + +The DHG also supports PECI, where the DHG queries Intel CPU temperatures, and +the ICH8 southbridge gets that data via PECI from the DHG, so that the +southbridge drives the fans. And the DHG supports SST, a one-wire serial bus. diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c index 212a1558c63b..da5828f2dfc2 100644 --- a/drivers/hwmon/w83627ehf.c +++ b/drivers/hwmon/w83627ehf.c @@ -32,8 +32,10 @@ Supports the following chips: - Chip #vin #fan #pwm #temp chip_id man_id - w83627ehf 10 5 4 3 0x88,0xa1 0x5ca3 + Chip #vin #fan #pwm #temp chip IDs man ID + w83627ehf 10 5 4 3 0x8850 0x88 0x5ca3 + 0x8860 0xa1 + w83627dhg 9 5 4 3 0xa020 0xc1 0x5ca3 */ #include <linux/module.h> @@ -55,8 +57,18 @@ static unsigned short address; * Super-I/O constants and functions */ +/* + * The three following globals are initialized in w83627ehf_find(), before + * the i2c-isa device is created. Otherwise, they could be stored in + * w83627ehf_data. This is ugly, but necessary, and when the driver is next + * updated to become a platform driver, the globals will disappear. + */ static int REG; /* The register to read/write */ static int VAL; /* The value to read/write */ +/* The w83627ehf/ehg have 10 voltage inputs, but the w83627dhg has 9. This + * value is also used in w83627ehf_detect() to export a device name in sysfs + * (e.g. w83627ehf or w83627dhg) */ +static int w83627ehf_num_in; #define W83627EHF_LD_HWM 0x0b @@ -65,8 +77,10 @@ static int VAL; /* The value to read/write */ #define SIO_REG_ENABLE 0x30 /* Logical device enable */ #define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */ -#define SIO_W83627EHF_ID 0x8840 -#define SIO_ID_MASK 0xFFC0 +#define SIO_W83627EHF_ID 0x8850 +#define SIO_W83627EHG_ID 0x8860 +#define SIO_W83627DHG_ID 0xa020 +#define SIO_ID_MASK 0xFFF0 static inline void superio_outb(int reg, int val) @@ -115,8 +129,12 @@ superio_exit(void) #define W83627EHF_REG_BANK 0x4E #define W83627EHF_REG_CONFIG 0x40 -#define W83627EHF_REG_CHIP_ID 0x49 -#define W83627EHF_REG_MAN_ID 0x4F + +/* Not currently used: + * REG_MAN_ID has the value 0x5ca3 for all supported chips. + * REG_CHIP_ID == 0x88/0xa1/0xc1 depending on chip model. + * REG_MAN_ID is at port 0x4f + * REG_CHIP_ID is at port 0x58 */ static const u16 W83627EHF_REG_FAN[] = { 0x28, 0x29, 0x2a, 0x3f, 0x553 }; static const u16 W83627EHF_REG_FAN_MIN[] = { 0x3b, 0x3c, 0x3d, 0x3e, 0x55c }; @@ -429,7 +447,7 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev) } /* Measured voltages and limits */ - for (i = 0; i < 10; i++) { + for (i = 0; i < w83627ehf_num_in; i++) { data->in[i] = w83627ehf_read_value(client, W83627EHF_REG_IN(i)); data->in_min[i] = w83627ehf_read_value(client, @@ -1121,7 +1139,7 @@ static void w83627ehf_device_remove_files(struct device *dev) device_remove_file(dev, &sda_sf3_arrays[i].dev_attr); for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++) device_remove_file(dev, &sda_sf3_arrays_fan4[i].dev_attr); - for (i = 0; i < 10; i++) { + for (i = 0; i < w83627ehf_num_in; i++) { device_remove_file(dev, &sda_in_input[i].dev_attr); device_remove_file(dev, &sda_in_alarm[i].dev_attr); device_remove_file(dev, &sda_in_min[i].dev_attr); @@ -1196,7 +1214,11 @@ static int w83627ehf_detect(struct i2c_adapter *adapter) client->flags = 0; dev = &client->dev; - strlcpy(client->name, "w83627ehf", I2C_NAME_SIZE); + if (w83627ehf_num_in == 9) + strlcpy(client->name, "w83627dhg", I2C_NAME_SIZE); + else /* just say ehf. 627EHG is 627EHF in lead-free packaging. */ + strlcpy(client->name, "w83627ehf", I2C_NAME_SIZE); + data->valid = 0; mutex_init(&data->update_lock); @@ -1246,7 +1268,7 @@ static int w83627ehf_detect(struct i2c_adapter *adapter) goto exit_remove; } - for (i = 0; i < 10; i++) + for (i = 0; i < w83627ehf_num_in; i++) if ((err = device_create_file(dev, &sda_in_input[i].dev_attr)) || (err = device_create_file(dev, &sda_in_alarm[i].dev_attr)) @@ -1340,7 +1362,17 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr) val = (superio_inb(SIO_REG_DEVID) << 8) | superio_inb(SIO_REG_DEVID + 1); - if ((val & SIO_ID_MASK) != SIO_W83627EHF_ID) { + switch (val & SIO_ID_MASK) { + case SIO_W83627DHG_ID: + w83627ehf_num_in = 9; + break; + case SIO_W83627EHF_ID: + case SIO_W83627EHG_ID: + w83627ehf_num_in = 10; + break; + default: + printk(KERN_WARNING "w83627ehf: unsupported chip ID: 0x%04x\n", + val); superio_exit(); return -ENODEV; } |