diff options
| -rw-r--r-- | drivers/mmc/host/sdhci-esdhc-imx.c | 52 |
1 files changed, 23 insertions, 29 deletions
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index 16b2840bc05a..b2187c5d1e96 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -144,8 +144,6 @@ * exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz. */ #define ESDHC_FLAG_ERR010450 BIT(10) -/* A clock frequency higher than this rate requires strobe dll control */ -#define ESDHC_STROBE_DLL_CLK_FREQ 100000000 struct esdhc_soc_data { u32 flags; @@ -939,39 +937,35 @@ static int esdhc_change_pinstate(struct sdhci_host *host, * edge of data_strobe line. Due to the time delay between CLK line and * data_strobe line, if the delay time is larger than one clock cycle, * then CLK and data_strobe line will be misaligned, read error shows up. - * So when the CLK is higher than 100MHz, each clock cycle is short enough, - * host should configure the delay target. */ static void esdhc_set_strobe_dll(struct sdhci_host *host) { u32 v; - if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) { - /* disable clock before enabling strobe dll */ - writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) & - ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, - host->ioaddr + ESDHC_VENDOR_SPEC); + /* disable clock before enabling strobe dll */ + writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) & + ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, + host->ioaddr + ESDHC_VENDOR_SPEC); - /* force a reset on strobe dll */ - writel(ESDHC_STROBE_DLL_CTRL_RESET, - host->ioaddr + ESDHC_STROBE_DLL_CTRL); - /* - * enable strobe dll ctrl and adjust the delay target - * for the uSDHC loopback read clock - */ - v = ESDHC_STROBE_DLL_CTRL_ENABLE | - (7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT); - writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL); - /* wait 1us to make sure strobe dll status register stable */ - udelay(1); - v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS); - if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK)) - dev_warn(mmc_dev(host->mmc), - "warning! HS400 strobe DLL status REF not lock!\n"); - if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK)) - dev_warn(mmc_dev(host->mmc), - "warning! HS400 strobe DLL status SLV not lock!\n"); - } + /* force a reset on strobe dll */ + writel(ESDHC_STROBE_DLL_CTRL_RESET, + host->ioaddr + ESDHC_STROBE_DLL_CTRL); + /* + * enable strobe dll ctrl and adjust the delay target + * for the uSDHC loopback read clock + */ + v = ESDHC_STROBE_DLL_CTRL_ENABLE | + (7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT); + writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL); + /* wait 1us to make sure strobe dll status register stable */ + udelay(1); + v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS); + if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK)) + dev_warn(mmc_dev(host->mmc), + "warning! HS400 strobe DLL status REF not lock!\n"); + if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK)) + dev_warn(mmc_dev(host->mmc), + "warning! HS400 strobe DLL status SLV not lock!\n"); } static void esdhc_reset_tuning(struct sdhci_host *host) |