Staging: w35und: remove dead code from wbhal.c

Remove tons of unused code from wbhal.c.

Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

2 files changed, 1 insertions, 332 deletions

diff --git a/drivers/staging/winbond/wbhal.c b/drivers/staging/winbond/wbhal.c
index b23c5055605c..8a9d21cbb0c0 100644
--- a/drivers/staging/winbond/wbhal.c
+++ b/drivers/staging/winbond/wbhal.c
@@ -2,13 +2,6 @@
 #include "wbhal_f.h"
 #include "wblinux_f.h"
 
-void hal_get_ethernet_address( phw_data_t pHwData, u8 *current_address )
-{
-	if( pHwData->SurpriseRemove ) return;
-
-	memcpy( current_address, pHwData->CurrentMacAddress, ETH_LENGTH_OF_ADDRESS );
-}
-
 void hal_set_ethernet_address( phw_data_t pHwData, u8 *current_address )
 {
 	u32 ltmp[2];
@@ -377,92 +370,6 @@ void hal_halt(phw_data_t pHwData, void *ppa_data)
 }
 
 //---------------------------------------------------------------------------------------------------
-void hal_set_rates(phw_data_t pHwData, u8 *pbss_rates,
-		   u8 length, unsigned char basic_rate_set)
-{
-	struct wb35_reg *reg = &pHwData->reg;
-	u32		tmp, tmp1;
-	u8		Rate[12]={ 2, 4, 11, 22, 12, 18, 24, 36, 48, 72, 96, 108 };
-	u8		SupportedRate[16];
-	u8		i, j, k, Count1, Count2, Byte;
-
-	if( pHwData->SurpriseRemove ) return;
-
-	if (basic_rate_set) {
-		reg->M28_MacControl &= ~0x000fff00;
-		tmp1 = 0x00000100;
-	} else {
-		reg->M28_MacControl &= ~0xfff00000;
-		tmp1 = 0x00100000;
-	}
-
-	tmp = 0;
-	for (i=0; i<length; i++) {
-		Byte = pbss_rates[i] & 0x7f;
-		for (j=0; j<12; j++) {
-			if( Byte == Rate[j] )
-				break;
-		}
-
-		if (j < 12)
-			tmp |= (tmp1<<j);
-	}
-
-	reg->M28_MacControl |= tmp;
-	Wb35Reg_Write( pHwData, 0x0828, reg->M28_MacControl );
-
-	// 930206.2.c M78 setting
-	j = k = Count1 = Count2 = 0;
-	memset( SupportedRate, 0, 16 );
-	tmp = 0x00100000;
-	tmp1 = 0x00000100;
-	for (i=0; i<12; i++) { // Get the supported rate
-		if (tmp & reg->M28_MacControl) {
-			SupportedRate[j] = Rate[i];
-
-			if (tmp1 & reg->M28_MacControl)
-				SupportedRate[j] |= 0x80;
-
-			if (k)
-				Count2++;
-			else
-				Count1++;
-
-			j++;
-		}
-
-		if (i==4 && k==0) {
-			if( !(reg->M28_MacControl & 0x000ff000) ) // if basic rate in 11g domain)
-			{
-				k = 1;
-				j = 8;
-			}
-		}
-
-		tmp <<= 1;
-		tmp1 <<= 1;
-	}
-
-	// Fill data into support rate until buffer full
-	//---20060926 add by anson's endian
-	for (i=0; i<4; i++)
-		*(u32 *)(SupportedRate+(i<<2)) = cpu_to_le32( *(u32 *)(SupportedRate+(i<<2)) );
-	//--- end 20060926 add by anson's endian
-	Wb35Reg_BurstWrite( pHwData,0x087c, (u32 *)SupportedRate, 4, AUTO_INCREMENT );
-	reg->M7C_MacControl = ((u32 *)SupportedRate)[0];
-	reg->M80_MacControl = ((u32 *)SupportedRate)[1];
-	reg->M84_MacControl = ((u32 *)SupportedRate)[2];
-	reg->M88_MacControl = ((u32 *)SupportedRate)[3];
-
-	// Fill length
-	tmp = Count1<<28 | Count2<<24;
-	reg->M78_ERPInformation &= ~0xff000000;
-	reg->M78_ERPInformation |= tmp;
-	Wb35Reg_Write( pHwData, 0x0878, reg->M78_ERPInformation );
-}
-
-
-//---------------------------------------------------------------------------------------------------
 void hal_set_beacon_period(  phw_data_t pHwData,  u16 beacon_period )
 {
 	u32	tmp;
@@ -476,7 +383,7 @@ void hal_set_beacon_period(  phw_data_t pHwData,  u16 beacon_period )
 }
 
 
-void hal_set_current_channel_ex(  phw_data_t pHwData,  ChanInfo channel )
+static void hal_set_current_channel_ex(  phw_data_t pHwData,  ChanInfo channel )
 {
 	struct wb35_reg *reg = &pHwData->reg;
 
@@ -502,12 +409,6 @@ void hal_set_current_channel(  phw_data_t pHwData,  ChanInfo channel )
 	hal_set_current_channel_ex( pHwData, channel );
 }
 //---------------------------------------------------------------------------------------------------
-void hal_get_current_channel(  phw_data_t pHwData,  ChanInfo *channel )
-{
-	channel->ChanNo = pHwData->Channel;
-	channel->band = pHwData->band;
-}
-//---------------------------------------------------------------------------------------------------
 void hal_set_accept_broadcast(  phw_data_t pHwData,  u8 enable )
 {
 	struct wb35_reg *reg = &pHwData->reg;
@@ -565,46 +466,6 @@ void hal_set_accept_beacon(  phw_data_t pHwData,  u8 enable )
 	Wb35Reg_Write( pHwData, 0x0800, reg->M00_MacControl );
 }
 //---------------------------------------------------------------------------------------------------
-void hal_set_multicast_address( phw_data_t pHwData, u8 *address, u8 number )
-{
-	struct wb35_reg *reg = &pHwData->reg;
-	u8		Byte, Bit;
-
-	if( pHwData->SurpriseRemove ) return;
-
-	//Erases and refills the card multicast registers. Used when an address
-	//    has been deleted and all bits must be recomputed.
-	reg->M04_MulticastAddress1 = 0;
-	reg->M08_MulticastAddress2 = 0;
-
-	while( number )
-	{
-		number--;
-		CardGetMulticastBit( (address+(number*ETH_LENGTH_OF_ADDRESS)), &Byte, &Bit);
-		reg->Multicast[Byte] |= Bit;
-	}
-
-	// Updating register
-	Wb35Reg_BurstWrite( pHwData, 0x0804, (u32 *)reg->Multicast, 2, AUTO_INCREMENT );
-}
-//---------------------------------------------------------------------------------------------------
-u8 hal_get_accept_beacon(  phw_data_t pHwData )
-{
-	struct wb35_reg *reg = &pHwData->reg;
-
-	if( pHwData->SurpriseRemove ) return 0;
-
-	if( reg->M00_MacControl & 0x04000000 )
-		return 1;
-	else
-		return 0;
-}
-
-unsigned char hal_reset_hardware( phw_data_t pHwData, void* ppa )
-{
-	// Not implement yet
-	return true;
-}
 
 void hal_stop(  phw_data_t pHwData )
 {
@@ -631,115 +492,11 @@ unsigned char hal_idle(phw_data_t pHwData)
 	return true;
 }
 //---------------------------------------------------------------------------------------------------
-void hal_set_cwmin(  phw_data_t pHwData,  u8	cwin_min )
-{
-	struct wb35_reg *reg = &pHwData->reg;
-
-	if( pHwData->SurpriseRemove ) return;
-
-	pHwData->cwmin = cwin_min;
-	reg->M2C_MacControl &= ~0x7c00;	//bit 10 ~ 14
-	reg->M2C_MacControl |= (pHwData->cwmin<<10);
-	Wb35Reg_Write( pHwData, 0x082c, reg->M2C_MacControl );
-}
-
-s32 hal_get_rssi(  phw_data_t pHwData,  u32 *HalRssiArry,  u8 Count )
-{
-	struct wb35_reg *reg = &pHwData->reg;
-	R01_DESCRIPTOR	r01;
-	s32 ltmp = 0, tmp;
-	u8	i;
-
-	if( pHwData->SurpriseRemove ) return -200;
-	if( Count > MAX_ACC_RSSI_COUNT ) // Because the TS may use this funtion
-		Count = MAX_ACC_RSSI_COUNT;
-
-	// RSSI = C1 + C2 * (agc_state[7:0] + offset_map(lna_state[1:0]))
-	// C1 = -195, C2 = 0.66 = 85/128
-	for (i=0; i<Count; i++)
-	{
-		r01.value = HalRssiArry[i];
-		tmp = ((( r01.R01_AGC_state + reg->LNAValue[r01.R01_LNA_state]) * 85 ) >>7 ) - 195;
-		ltmp += tmp;
-	}
-	ltmp /= Count;
-	if( pHwData->phy_type == RF_AIROHA_2230 ) ltmp -= 5; // 10;
-	if( pHwData->phy_type == RF_AIROHA_2230S ) ltmp -= 5; // 10; 20060420 Add this
-
-	//if( ltmp < -200 ) ltmp = -200;
-	if( ltmp < -110 ) ltmp = -110;// 1.0.24.0 For NJRC
-
-	return ltmp;
-}
-//----------------------------------------------------------------------------------------------------
-s32 hal_get_rssi_bss(struct wbsoft_priv *adapter,  u16 idx,  u8 Count)
-{
-	phw_data_t pHwData = &adapter->sHwData;
-	struct wb35_reg *reg = &pHwData->reg;
-	R01_DESCRIPTOR	r01;
-	s32 ltmp = 0, tmp;
-	u8	i, j;
-//	u32 *HalRssiArry = psBSS(idx)->HalRssi;
-
-	if( pHwData->SurpriseRemove ) return -200;
-	if( Count > MAX_ACC_RSSI_COUNT ) // Because the TS may use this funtion
-		Count = MAX_ACC_RSSI_COUNT;
-
-	// RSSI = C1 + C2 * (agc_state[7:0] + offset_map(lna_state[1:0]))
-	// C1 = -195, C2 = 0.66 = 85/128
-#if 0
-	for (i=0; i<Count; i++)
-	{
-		r01.value = HalRssiArry[i];
-		tmp = ((( r01.R01_AGC_state + reg->LNAValue[r01.R01_LNA_state]) * 85 ) >>7 ) - 195;
-		ltmp += tmp;
-	}
-#else
-	if (psBSS(idx)->HalRssiIndex == 0)
-		psBSS(idx)->HalRssiIndex = MAX_ACC_RSSI_COUNT;
-	j = (u8)psBSS(idx)->HalRssiIndex-1;
-
-	for (i=0; i<Count; i++)
-	{
-		r01.value = psBSS(idx)->HalRssi[j];
-		tmp = ((( r01.R01_AGC_state + reg->LNAValue[r01.R01_LNA_state]) * 85 ) >>7 ) - 195;
-		ltmp += tmp;
-		if (j == 0)
-		{
-			j = MAX_ACC_RSSI_COUNT;
-		}
-		j--;
-	}
-#endif
-	ltmp /= Count;
-	if( pHwData->phy_type == RF_AIROHA_2230 ) ltmp -= 5; // 10;
-	if( pHwData->phy_type == RF_AIROHA_2230S ) ltmp -= 5; // 10; 20060420 Add this
-
-	//if( ltmp < -200 ) ltmp = -200;
-	if( ltmp < -110 ) ltmp = -110;// 1.0.24.0 For NJRC
-
-	return ltmp;
-}
-
-//---------------------------------------------------------------------------
-
 void hal_set_phy_type(  phw_data_t pHwData,  u8 PhyType )
 {
 	pHwData->phy_type = PhyType;
 }
 
-void hal_get_phy_type(  phw_data_t pHwData,  u8 *PhyType )
-{
-	*PhyType = pHwData->phy_type;
-}
-
-void hal_reset_counter(  phw_data_t pHwData )
-{
-	pHwData->dto_tx_retry_count = 0;
-	pHwData->dto_tx_frag_count = 0;
-	memset( pHwData->tx_retry_count, 0, 8);
-}
-
 void hal_set_radio_mode( phw_data_t pHwData,  unsigned char radio_off)
 {
 	struct wb35_reg *reg = &pHwData->reg;
@@ -769,22 +526,6 @@ u8 hal_get_antenna_number(  phw_data_t pHwData )
 		return 1;
 }
 
-void hal_set_antenna_number(  phw_data_t pHwData, u8 number )
-{
-
-	struct wb35_reg *reg = &pHwData->reg;
-
-	if (number == 1) {
-		reg->BB2C |= BIT(11);
-	} else {
-		reg->BB2C &= ~BIT(11);
-	}
-	Wb35Reg_Write( pHwData, 0x102c, reg->BB2C );
-#ifdef _PE_STATE_DUMP_
-	WBDEBUG(("Current antenna number : %d\n", number));
-#endif
-}
-
 //----------------------------------------------------------------------------------------------------
 //0 : radio on; 1: radio off
 u8 hal_get_hw_radio_off(  phw_data_t pHwData )
@@ -821,57 +562,7 @@ unsigned char hal_set_dxx_reg(  phw_data_t pHwData,  u16 number,  u32 value )
 	return ret;
 }
 
-void hal_scan_status_indicate(phw_data_t pHwData, unsigned char IsOnProgress)
-{
-	if( pHwData->SurpriseRemove ) return;
-	pHwData->LED_Scanning = IsOnProgress ? 1 : 0;
-}
-
-void hal_system_power_change(phw_data_t pHwData, u32 PowerState)
-{
-	if( PowerState != 0 )
-	{
-		pHwData->SurpriseRemove = 1;
-		if( pHwData->WbUsb.IsUsb20 )
-			hal_stop( pHwData );
-	}
-	else
-	{
-		if( !pHwData->WbUsb.IsUsb20 )
-			hal_stop( pHwData );
-	}
-}
-
-void hal_surprise_remove(struct wbsoft_priv *adapter)
-{
-	phw_data_t pHwData = &adapter->sHwData;
-
-	if (atomic_inc_return( &pHwData->SurpriseRemoveCount ) == 1) {
-		#ifdef _PE_STATE_DUMP_
-		WBDEBUG(("Calling hal_surprise_remove\n"));
-		#endif
-	}
-}
-
-void hal_rate_change(struct wbsoft_priv *adapter) // Notify the HAL rate is changing 20060613.1
-{
-	phw_data_t pHwData = &adapter->sHwData;
-	u8		rate = CURRENT_TX_RATE;
-
-	BBProcessor_RateChanging( pHwData, rate );
-}
-
 void hal_set_rf_power(phw_data_t pHwData, u8 PowerIndex)
 {
 	RFSynthesizer_SetPowerIndex( pHwData, PowerIndex );
 }
-
-unsigned char hal_set_LED(phw_data_t pHwData, u32 Mode) // 20061108 for WPS led control
-{
-	pHwData->LED_Blinking = 0;
-	pHwData->LED_control = Mode;
-	pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(10);
-	add_timer(&pHwData->LEDTimer);
-	return true;
-}
-
diff --git a/drivers/staging/winbond/wbhal_f.h b/drivers/staging/winbond/wbhal_f.h
index dc5709f5a52a..e805f40f6354 100644
--- a/drivers/staging/winbond/wbhal_f.h
+++ b/drivers/staging/winbond/wbhal_f.h
@@ -26,9 +26,6 @@ void hal_set_power_save_mode(  phw_data_t pHwData,  unsigned char power_save,  u
 void hal_get_power_save_mode(  phw_data_t pHwData,   u8 *pin_pwr_save );
 void hal_set_slot_time(  phw_data_t pHwData,  u8 type );
 #define hal_set_atim_window( _A, _ATM )
-void hal_set_rates(  phw_data_t pHwData,  u8 *pbss_rates,  u8 length,  unsigned char basic_rate_set );
-#define hal_set_basic_rates( _A, _R, _L ) hal_set_rates( _A, _R, _L, TRUE )
-#define hal_set_op_rates( _A, _R, _L ) hal_set_rates( _A, _R, _L, FALSE )
 void hal_start_bss(  phw_data_t pHwData,  u8 mac_op_mode );
 void hal_join_request(  phw_data_t pHwData,  u8 bss_type ); // 0:BSS STA 1:IBSS STA//
 void hal_stop_sync_bss(  phw_data_t pHwData );
@@ -41,35 +38,23 @@ void hal_set_listen_interval(  phw_data_t pHwData,  u16 listen_interval );
 void hal_set_cap_info(  phw_data_t pHwData,  u16 capability_info );
 void hal_set_ssid(  phw_data_t pHwData,  u8 *pssid,  u8 ssid_len );
 void hal_set_current_channel(  phw_data_t pHwData,  ChanInfo channel );
-void hal_set_current_channel_ex(  phw_data_t pHwData,  ChanInfo channel );
-void hal_get_current_channel(  phw_data_t pHwData,  ChanInfo *channel );
 void hal_set_accept_broadcast(  phw_data_t pHwData,  u8 enable );
 void hal_set_accept_multicast(  phw_data_t pHwData,  u8 enable );
 void hal_set_accept_beacon(  phw_data_t pHwData,  u8 enable );
-void hal_set_multicast_address(  phw_data_t pHwData,  u8 *address,  u8 number );
-u8 hal_get_accept_beacon(  phw_data_t pHwData );
 void hal_stop(  phw_data_t pHwData );
 void hal_halt(  phw_data_t pHwData, void *ppa_data );
 void hal_start_tx0(  phw_data_t pHwData );
 void hal_set_phy_type(  phw_data_t pHwData,  u8 PhyType );
-void hal_get_phy_type(  phw_data_t pHwData,  u8 *PhyType );
-unsigned char hal_reset_hardware(  phw_data_t pHwData,  void* ppa );
-void hal_set_cwmin(  phw_data_t pHwData,  u8	cwin_min );
 #define hal_get_cwmin( _A ) ( (_A)->cwmin )
 void hal_set_cwmax(  phw_data_t pHwData,  u16 cwin_max );
 #define hal_get_cwmax( _A ) ( (_A)->cwmax )
 void hal_set_rsn_wpa(  phw_data_t pHwData,  u32 * RSN_IE_Bitmap , u32 * RSN_OUI_type , unsigned char bDesiredAuthMode);
-//s32 hal_get_rssi(  phw_data_t pHwData,  u32 HalRssi );
-s32 hal_get_rssi(  phw_data_t pHwData,  u32 *HalRssiArry,  u8 Count );
-s32 hal_get_rssi_bss(struct wbsoft_priv *adapter,  u16 idx,  u8 Count);
 void hal_set_connect_info(  phw_data_t pHwData,  unsigned char boConnect );
 u8 hal_get_est_sq3(  phw_data_t pHwData,  u8 Count );
 void hal_set_rf_power(  phw_data_t pHwData,  u8 PowerIndex ); // 20060621 Modify
-void hal_reset_counter(  phw_data_t pHwData );
 void hal_set_radio_mode(  phw_data_t pHwData,  unsigned char boValue);
 void hal_descriptor_indicate(  phw_data_t pHwData,  PDESCRIPTOR pDes );
 u8 hal_get_antenna_number(  phw_data_t pHwData );
-void hal_set_antenna_number(  phw_data_t pHwData, u8 number );
 u32 hal_get_bss_pk_cnt(  phw_data_t pHwData );
 #define hal_get_region_from_EEPROM( _A ) ( (_A)->reg.EEPROMRegion )
 void hal_set_accept_promiscuous		(  phw_data_t pHwData,  u8 enable);
@@ -80,20 +65,13 @@ u8 hal_get_hw_radio_off			(  phw_data_t pHwData );
 #define hal_rssi_boundary_high( _A ) (_A->RSSI_high)
 #define hal_rssi_boundary_low( _A ) (_A->RSSI_low)
 #define hal_scan_interval( _A )		(_A->Scan_Interval)
-void hal_scan_status_indicate(  phw_data_t pHwData, u8 status);	// 0: complete, 1: in progress
-void hal_system_power_change(  phw_data_t pHwData, u32 PowerState ); // 20051230 -=D0 1=D1 ..
-void hal_surprise_remove(struct wbsoft_priv *adapter);
 
 #define PHY_DEBUG( msg, args... )
 
-
-
-void hal_rate_change(struct wbsoft_priv *adapter); // Notify the HAL rate is changing 20060613.1
 unsigned char hal_get_dxx_reg(  phw_data_t pHwData,  u16 number,  u32 * pValue );
 unsigned char hal_set_dxx_reg(  phw_data_t pHwData,  u16 number,  u32 value );
 #define hal_get_time_count( _P )	(_P->time_count/10)	// return 100ms count
 #define hal_detect_error( _P )		(_P->WbUsb.DetectCount)
-unsigned char hal_set_LED(  phw_data_t pHwData,  u32 Mode ); // 20061108 for WPS led control
 
 //-------------------------------------------------------------------------
 // The follow function is unused for IS89C35