diff options
| author | stephen hemminger <shemminger@vyatta.com> | 2011-07-07 05:50:58 +0000 |
|---|---|---|
| committer | David S. Miller <davem@davemloft.net> | 2011-07-08 08:53:33 -0700 |
| commit | 8e11680f5e1abc85298c12a99e2b741249eadc0c (patch) | |
| tree | af9f39ed9b3607e2480776d40a0845b1da612d69 /drivers/net/sky2.c | |
| parent | aa5ca96c8fffea769aedd795f48695112393dc89 (diff) | |
sky2: use correct Inter Packet Gap at 10/100mbit
This is another fix picked out of the vendor driver. The IPG value
in the serial mode register is supposed to be programmed differently
at lower speeds.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diffstat (limited to 'drivers/net/sky2.c')
| -rw-r--r-- | drivers/net/sky2.c | 25 |
1 files changed, 22 insertions, 3 deletions
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 3fc8683b2ff0..b1a675a94a17 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -714,6 +714,20 @@ static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port) sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); } +/* configure IPG according to used link speed */ +static void sky2_set_ipg(struct sky2_port *sky2) +{ + u16 reg; + + reg = gma_read16(sky2->hw, sky2->port, GM_SERIAL_MODE); + reg &= ~GM_SMOD_IPG_MSK; + if (sky2->speed > SPEED_100) + reg |= IPG_DATA_VAL(IPG_DATA_DEF_1000); + else + reg |= IPG_DATA_VAL(IPG_DATA_DEF_10_100); + gma_write16(sky2->hw, sky2->port, GM_SERIAL_MODE, reg); +} + /* Enable Rx/Tx */ static void sky2_enable_rx_tx(struct sky2_port *sky2) { @@ -882,7 +896,7 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) /* serial mode register */ reg = DATA_BLIND_VAL(DATA_BLIND_DEF) | - GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF); + GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF_1000); if (hw->dev[port]->mtu > ETH_DATA_LEN) reg |= GM_SMOD_JUMBO_ENA; @@ -2053,6 +2067,8 @@ static void sky2_link_up(struct sky2_port *sky2) [FC_BOTH] = "both", }; + sky2_set_ipg(sky2); + sky2_enable_rx_tx(sky2); gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK); @@ -2290,8 +2306,11 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu) dev->mtu = new_mtu; netdev_update_features(dev); - mode = DATA_BLIND_VAL(DATA_BLIND_DEF) | - GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF); + mode = DATA_BLIND_VAL(DATA_BLIND_DEF) | GM_SMOD_VLAN_ENA; + if (sky2->speed > SPEED_100) + mode |= IPG_DATA_VAL(IPG_DATA_DEF_1000); + else + mode |= IPG_DATA_VAL(IPG_DATA_DEF_10_100); if (dev->mtu > ETH_DATA_LEN) mode |= GM_SMOD_JUMBO_ENA; |