[netdrvr] skfp: remove a bunch of dead code

The driver has not compiled in anything except PCI support for many
years (see drivers/net/skfp/Makefile).  This driver is also unmaintained
for many years, so arguments for keeping the cross-OS, cross-bus (ISA,
EISA, MCA) code do not exist.

Signed-off-by: Jeff Garzik <jeff@garzik.org>

4 files changed, 2 insertions, 844 deletions

diff --git a/drivers/net/skfp/h/mbuf.h b/drivers/net/skfp/h/mbuf.h
index b339d1f2e0e5..f2aadcda9e7f 100644
--- a/drivers/net/skfp/h/mbuf.h
+++ b/drivers/net/skfp/h/mbuf.h
@@ -15,11 +15,7 @@
 #ifndef	_MBUF_
 #define _MBUF_
 
-#ifndef PCI
-#define M_SIZE	4550
-#else
 #define M_SIZE	4504
-#endif
 
 #ifndef MAX_MBUF
 #define MAX_MBUF	4
diff --git a/drivers/net/skfp/h/skfbi.h b/drivers/net/skfp/h/skfbi.h
index ba347d6910f1..d25c9f849842 100644
--- a/drivers/net/skfp/h/skfbi.h
+++ b/drivers/net/skfp/h/skfbi.h
@@ -21,791 +21,10 @@
 #endif
 
 /*
- * physical address offset + IO-Port base address
- */
-#ifndef	PCI
-#define	ADDR(a)	((a)+smc->hw.iop)
-#define	ADDRS(smc,a) ((a)+(smc)->hw.iop)
-#endif
-
-/*
- * FDDI-Fx (x := {I(SA), E(ISA), M(CA), P(CI)})
+ * FDDI-Fx (x := {I(SA), P(CI)})
  *	address calculation & function defines
  */
 
-#ifdef	EISA
-
-/*
- * Configuration PROM:	 !! all 8-Bit IO's !!
- *					    |<-	  MAC-Address	 ->|
- *	/-+--+--+--+--+-//-+--+--+--+--+-//-+--+--+--+--+-//-+--+--+--+--+-/
- * val:	  |PROD_ID0..3|	   | free      |    |00|00|5A|40|    |nn|mm|00|00|
- *	/-+--+--+--+--+-//-+--+--+--+--+-//-+--+--+--+--+-//-+--+--+--+--+-/
- * IO-	  ^	      ^	   ^		    ^		     ^
- * port	0C80	    0C83  0C88		   0C90		    0C98
- *	  |	       \
- *	  |		\
- *	  |		 \______________________________________________
- * EISA Expansion Board Product ID:					\
- * BIT:	  |7 6 5 4 3 2 1 0|						 \
- *	  | PROD_ID0	  | PROD_ID1	  | PROD_ID2	  | PROD_ID3	  |
- *	  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
- *	  |0| MAN_C0  | MAN_C1	| MAN_C2  | PROD1 | PROD0 | REV1  | REV0  |
- *	  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
- *	   ^=reserved			  | product numb. | revision numb |
- * MAN_Cx = compressed manufacterer code (x:=0..2)
- *	ASCII : 'A'..'Z' : 0x41..0x5A -> compr.(c-0x40) : 0x01..0x1A (5Bits!)
- */
-
-#ifndef	MULT_OEM
-#ifndef	OEM_CONCEPT
-#define	MAN_C0		('S'-0x40)
-#define	MAN_C1		('K'-0x40)
-#define	MAN_C2		('D'-0x40)
-#define	PROD_ID0	(u_char)((MAN_C0<<2) | (MAN_C1>>3))
-#define	PROD_ID1	(u_char)(((MAN_C1<<5) & 0xff) | MAN_C2)
-#define	PROD_ID2	(u_char)(1)	/* prod. nr. */
-#define	PROD_ID3	(u_char)(0)	/* rev. nr. */
-
-#ifndef	OEM_USER_DATA
-#define	OEM_USER_DATA	"SK-NET FDDI V2.0 Userdata"
-#endif
-#else	/*  OEM_CONCEPT */
-
-/* MAN_C(0|1|2) no longer present (ra). */
-#define	PROD_ID0	(u_char)OEM_PROD_ID0
-#define	PROD_ID1	(u_char)OEM_PROD_ID1
-#define	PROD_ID2	(u_char)OEM_PROD_ID2
-#define	PROD_ID3	(u_char)OEM_PROD_ID3
-#endif	/* OEM_CONCEPT */
-
-#define	SKLOGO		PROD_ID0, PROD_ID1, PROD_ID2, PROD_ID3
-#endif	/* MULT_OEM */
-
-#define	SADDRL	(0)		/* start address SKLOGO */
-#define	SA_MAC	(0x10)		/* start addr. MAC_AD within the PROM */
-#define	PRA_OFF	(4)
-#define SA_PMD_TYPE	(8)	/* start addr. PMD-Type */
-
-#define	SKFDDI_PSZ	32		/* address PROM size */
-
-/*
- * address transmission from logical to physical offset address on board
- */
-#define FMA(a)	(0x0400|((a)<<1))	/* FORMAC+ (r/w) */
-#define P1A(a)	(0x0800|((a)<<1))	/* PLC1 (r/w) */
-#define P2A(a)	(0x0840|((a)<<1))	/* PLC2 (r/w) */
-#define TIA(a)	(0x0880|((a)<<1))	/* Timer (r/w) */
-#define PRA(a)	(0x0c80| (a))		/* configuration PROM */
-#define	C0A(a)	(0x0c84| (a))		/* config. RAM */
-#define	C1A(a)	(0x0ca0| (a))		/* IRQ-, DMA-nr., EPROM type */
-#define	C2A(a)	(0x0ca4| (a))		/* EPROM and PAGE selector */
-
-#define	CONF	C0A(0)			/* config RAM (card enable bit port) */
-#define PGRA	C2A(0)			/* Flash page register */
-#define	CDID	PRA(0)			/* Card ID I/O port addr. offset */
-
-
-/*
- * physical address offset + slot specific IO-Port base address
- */
-#define FM_A(a)	(FMA(a)+smc->hw.iop)	/* FORMAC Plus physical addr */
-#define P1_A(a)	(P1A(a)+smc->hw.iop)	/* PLC1 (r/w) */
-#define P2_A(a)	(P2A(a)+smc->hw.iop)	/* PLC2 (r/w) */
-#define TI_A(a)	(TIA(a)+smc->hw.iop)	/* Timer (r/w) */
-#define PR_A(a)	(PRA(a)+smc->hw.iop)	/* config. PROM */
-#define C0_A(a)	(C0A(a)+smc->hw.iop)	/* config. RAM */
-#define C1_A(a)	(C1A(a)+smc->hw.iop)	/* config. RAM */
-#define C2_A(a)	(C2A(a)+smc->hw.iop)	/* config. RAM */
-
-
-#define	CSRA	0x0008		/* control/status register address (r/w) */
-#define	ISRA	0x0008		/* int. source register address (upper 8Bits) */
-#define PLC1I	0x001a		/* clear PLC1 interrupt (write only) */
-#define PLC2I	0x0020		/* clear PLC2 interrupt (write only) */
-#define CSFA	0x001c		/* control/status FIFO BUSY flags (read only) */
-#define RQAA	0x001c		/* Request reg. (write only) */
-#define WCTA	0x001e		/* word counter (r/w) */
-#define	FFLAG	0x005e		/* FLAG/V_FULL (FIFO almost full, write only)*/
-
-#define	CSR_A	(CSRA+smc->hw.iop)	/* control/status register address (r/w) */
-#ifdef UNIX
-#define	CSR_AS(smc)	(CSRA+(smc)->hw.iop)	/* control/status register address (r/w) */
-#endif
-#define	ISR_A	(ISRA+smc->hw.iop)	/* int. source register address (upper 8Bits) */
-#define PLC1_I	(PLC1I+smc->hw.iop)	/* clear PLC1 internupt (write only) */
-#define PLC2_I	(PLC2I+smc->hw.iop)	/* clear PLC2 interrupt (write only) */
-#define CSF_A	(CSFA+smc->hw.iop)	/* control/status FIFO BUSY flags (r/w) */
-#define RQA_A	(RQAA+smc->hw.iop)	/* Request reg. (write only) */
-#define WCT_A	(WCTA+smc->hw.iop)	/* word counter (r/w) */
-#define	FFLAG_A	(FFLAG+smc->hw.iop)	/* FLAG/V_FULL (FIFO almost full, write only)*/
-
-/*
- * control/status register CSRA	bits
- */
-/* write */
-#define CS_CRESET	0x01		/* Card reset (0=reset) */
-#define	CS_RESET_FIFO	0x02		/* FIFO reset (0=reset) */
-#define	CS_IMSK		0x04		/* enable IRQ (1=enable, 0=disable) */
-#define	CS_EN_IRQ_TC	0x08		/* enable IRQ from transfer counter */
-#define CS_BYPASS	0x20		/* bypass switch (0=remove, 1=insert)*/
-#define CS_LED_0	0x40		/* switch LED 0 */
-#define	CS_LED_1	0x80		/* switch LED 1 */
-/* read */
-#define	CS_BYSTAT	0x40		/* 0=Bypass exist, 1= ..not */
-#define	CS_SAS		0x80		/* single attachement station (=1) */
-
-/*
- * control/status register CSFA bits (FIFO)
- */
-#define	CSF_MUX0	0x01
-#define	CSF_MUX1	0x02
-#define	CSF_HSREQ0	0x04
-#define	CSF_HSREQ1	0x08
-#define	CSF_HSREQ2	0x10
-#define	CSF_BUSY_DMA	0x40
-#define	CSF_BUSY_FIFO	0x80
-
-/*
- * Interrupt source register ISRA (upper 8 data bits) read only & low activ.
- */
-#define IS_MINTR1	0x0100		/* FORMAC ST1U/L & ~IMSK1U/L*/
-#define IS_MINTR2	0x0200		/* FORMAC ST2U/L & ~IMSK2U/L*/
-#define IS_PLINT1	0x0400		/* PLC1 */
-#define IS_PLINT2	0x0800		/* PLC2 */
-#define IS_TIMINT	0x1000		/* Timer 82C54-2 */
-#define	IS_TC		0x2000		/* transf. counter */
-
-#define	ALL_IRSR (IS_MINTR1|IS_MINTR2|IS_PLINT1|IS_PLINT2|IS_TIMINT|IS_TC)
-
-/*
- * CONFIG<0> RAM (C0_A())
- */
-#define	CFG_CARD_EN	0x01		/* card enable */
-
-/*
- * CONFIG<1> RAM (C1_A())
- */
-#define	CFG_IRQ_SEL	0x03		/* IRQ select (4 nr.) */
-#define	CFG_IRQ_TT	0x04		/* IRQ trigger type (LEVEL/EDGE) */
-#define	CFG_DRQ_SEL	0x18		/* DMA requ. (4 nr.) */
-#define	CFG_BOOT_EN	0x20		/* 0=BOOT-, 1=Application Software */
-#define	CFG_PROG_EN	0x40		/* V_Prog for FLASH_PROM (1=on) */
-
-/*
- * CONFIG<2> RAM (C2_A())
- */
-#define	CFG_EPROM_SEL	0x0f		/* FPROM start address selection */
-#define	CFG_PAGE	0xf0		/* FPROM page selection */
-
-
-#define	READ_PROM(a)	((u_char)inp(a))
-#define	GET_PAGE(i)	outp(C2_A(0),((int)(i)<<4) | (inp(C2_A(0)) & ~CFG_PAGE))
-#define	FPROM_SW()	(inp(C1_A(0)) & CFG_BOOT_EN)
-
-#define	MAX_PAGES	16		/* 16 pages */
-#define	MAX_FADDR	0x2000		/* 8K per page */
-#define	VPP_ON()	outp(C1_A(0),inp(C1_A(0)) |  CFG_PROG_EN)
-#define	VPP_OFF()	outp(C1_A(0),inp(C1_A(0)) & ~CFG_PROG_EN)
-
-#define	DMA_BUSY()	(inpw(CSF_A) & CSF_BUSY_DMA)
-#define FIFO_BUSY()	(inpw(CSF_A) & CSF_BUSY_FIFO)
-#define	DMA_FIFO_BUSY()	(inpw(CSF_A) & (CSF_BUSY_DMA | CSF_BUSY_FIFO))
-#define	BUS_CHECK()
-
-#ifdef UNISYS
-/* For UNISYS use another macro with drv_usecewait function */
-#define CHECK_DMA() {u_long k = 1000000; \
-		while (k && (DMA_BUSY())) { k--; drv_usecwait(20); } \
-		if (!k) SMT_PANIC(smc,HWM_E0003,HWM_E0003_MSG) ; }
-#else
-#define CHECK_DMA() {u_long k = 1000000 ;\
-		while (k && (DMA_BUSY())) k-- ;\
-		if (!k) SMT_PANIC(smc,HWM_E0003,HWM_E0003_MSG) ; }
-#endif
-
-#define CHECK_FIFO() {u_long k = 1000000 ;\
-		while (k && (FIFO_BUSY())) k-- ;\
-		if (!k) SMT_PANIC(smc,HWM_E0019,HWM_E0019_MSG) ; }
-
-#define CHECK_DMA_FIFO() {u_long k = 1000000 ;\
-		while (k && (DMA_FIFO_BUSY())) k-- ;\
-		if (!k) SMT_PANIC(smc,HWM_E0004,HWM_E0004_MSG) ; }
-
-#define	GET_ISR()	~inpw(ISR_A)
-#define CHECK_ISR()	~inpw(ISR_A)
-
-#ifndef UNIX
-#ifndef	WINNT
-#define	CLI_FBI()	outpw(CSR_A,(inpw(CSR_A)&\
-			(CS_CRESET|CS_BYPASS))|CS_RESET_FIFO|smc->hw.led)
-#else	/* WINNT */
-#define CLI_FBI()	outpw(CSR_A,(l_inpw(CSR_A)&\
-			(CS_CRESET|CS_BYPASS))|CS_RESET_FIFO|smc->hw.led)
-#endif	/* WINNT */
-#else	/* UNIX */
-#define	CLI_FBI(smc)	outpw(CSR_AS(smc),(inpw(CSR_AS(smc))&\
-			(CS_CRESET|CS_BYPASS))|CS_RESET_FIFO|(smc)->hw.led)
-#endif
-
-#ifndef UNIX
-#define	STI_FBI()	outpw(CSR_A,(inpw(CSR_A)&\
-		(CS_CRESET|CS_BYPASS|CS_RESET_FIFO))|CS_IMSK|smc->hw.led)
-#else
-#define	STI_FBI(smc)	outpw(CSR_AS(smc),(inpw(CSR_AS(smc))&\
-		(CS_CRESET|CS_BYPASS|CS_RESET_FIFO))|CS_IMSK|(smc)->hw.led)
-#endif
-
-/* EISA DMA Controller */
-#define DMA_WRITE_SINGLE_MASK_BIT_M	0x0a	/* Master DMA Controller */
-#define DMA_WRITE_SINGLE_MASK_BIT_S	0xd4	/* Slave DMA Controller */
-#define DMA_CLEAR_BYTE_POINTER_M	0x0c
-#define DMA_CLEAR_BYTE_POINTER_S	0xd8
-
-#endif	/* EISA */
-
-#ifdef	MCA
-
-/*
- * POS Register:	 !! all I/O's are 8-Bit !!
- */
-#define	POS_SYS_SETUP	0x94	/* system setup register */
-#define	POS_SYSTEM	0xff	/* system mode */
-
-#define	POS_CHANNEL_POS	0x96	/* register slot ID */
-#define	POS_CHANNEL_BIT	0x08	/* mask for -"- */
-
-#define	POS_BASE	0x100	/* POS base address */
-#define	POS_ID_LOW	POS_BASE	/* card ID low */
-#define	POS_ID_HIGH	(POS_BASE+1)	/* card ID high */
-#define	POS_102		(POS_BASE+2)	/* card en., arbitration level .. */
-#define	POS_103		(POS_BASE+3)	/* FPROM addr, page */
-#define	POS_104		(POS_BASE+4)	/* I/O, IRQ */
-#define	POS_105		(POS_BASE+5)	/* POS_CHCK */
-#define	POS_106		(POS_BASE+6)	/* to read VPD */
-#define	POS_107		(POS_BASE+7)	/* added without function */
-
-/* FM1 card IDs */
-#define	FM1_CARD_ID0	0x83
-#define	FM1_CARD_ID1	0
-
-#define	FM1_IBM_ID0	0x9c
-#define	FM1_IBM_ID1	0x8f
-
-
-/* FM2 card IDs */
-#define	FM2_CARD_ID0	0xab
-#define	FM2_CARD_ID1	0
-
-#define	FM2_IBM_ID0	0x7e
-#define	FM2_IBM_ID1	0x8f
-
-/* Board revision. */
-#define FM1_REV		0
-#define FM2_REV		1
-
-#define	MAX_SLOT	8
-
-/*
- * POS_102
- */
-#define	POS_CARD_EN	0x01	/* card enable =1 */
-#define	POS_SDAT_EN	0x02	/* enable 32-bit streaming data mode */
-#define	POS_EN_CHKINT	0x04	/* enable int. from check line asserted */
-#define	POS_EN_BUS_ERR	0x08	/* enable int. on invalid busmaster transf. */
-#define	POS_FAIRNESS	0x10	/* fairnes on =1 */
-/* attention: arbitration level used with bit 0 POS 105 */
-#define	POS_LARBIT	0xe0	/* arbitration level	(0,0,0)->level = 0x8
-							(1,1,1)->level = 0xf */
-/*
- * POS_103
- */
-#define	POS_PAGE	0x07	/* FPROM page selection */
-#define	POS_BOOT_EN	0x08	/* boot PROM enable =1 */
-#define	POS_MSEL	0x70	/* memory start address for FPROM mapping */
-#define	PROG_EN		0x80	/* FM1: Vpp prog on/off */
-#define	POS_SDR		0x80	/* FM2: Streaming data bit */
-
-/*
- * POS_104
- */
-#define	POS_IOSEL	0x3f	/* selected I/O base address */
-#define	POS_IRQSEL	0xc0	/* selected interrupt */
-
-/*
- * POS_105
- */
-#define	POS_CHCK	0x80
-#define POS_SYNC_ERR	0x20	/* FM2: synchronous error reporting	*/
-#define POS_PAR_DATA	0x10	/* FM2: data parity enable bit	*/
-#define POS_PAR_ADDR	0x08	/* FM2: address parity enable bit	*/
-#define	POS_IRQHSEL	0x02	/* FM2: Highest bit for IRQ_selection	*/
-#define POS_HARBIT	0x01	/* Highest bit in Bus arbitration selection */
-
-#define	SA_MAC	(0)		/* start addr. MAC_AD within the PROM	*/
-#define	PRA_OFF	(0)
-#define SA_PMD_TYPE	(8)	/* start addr. PMD-Type	*/
-
-/*
- * address transmission from logical to physical offset address on board
- */
-#define	FMA(a)	(0x0100|((a)<<1))	/* FORMAC+ (r/w) */
-#define	P2(a)	(0x00c0|((a)<<1))	/* PLC2 (r/w) (DAS) */
-#define	P1(a)	(0x0080|((a)<<1))	/* PLC1 (r/w) */
-#define	TI(a)	(0x0060|((a)<<1))	/* Timer (r/w) */
-#define	PR(a)	(0x0040|((a)<<1))	/* configuration PROM */
-#define	CS(a)	(0x0020| (a))		/* control/status */
-#define	FF(a)	(0x0010|((a)<<1))	/* FIFO ASIC */
-#define	CT(a)	(0x0000|((a)<<1))	/* counter */
-
-/*
- * counter
- */
-#define	ACLA	CT(0)		/* address counter low */
-#define	ACHA	CT(1)		/* address counter high */
-#define	BCN	CT(2)		/* byte counter */
-#define	MUX	CT(3)		/* MUX-register */
-#define	WCN	CT(0x08)	/* word counter */
-#define	FFLG	CT(0x09)	/* FIFO Flags */
-
-/*
- * test/control register (FM2 only)
- */
-#define CNT_TST	0x018		/* Counter test control register */
-#define CNT_STP 0x01a		/* Counter test step reg. (8 Bit) */
-
-/*
- * CS register (read only)
- */
-#define	CSRA	CS(0)		/* control/status register address */
-#define	CSFA	CS(2)		/* control/status FIFO BUSY ...	 */
-#define	ISRA	CS(4)		/* first int. source register address */
-#define	ISR2	CS(6)		/* second int. source register address */
-#define	LEDR	CS(0x0c)	/* LED register r/w */
-#define	CSIL	CS(0x10)	/* I/O mapped POS_ID_low (100) */
-#define	CSIH	CS(0x12)	/*	- " - POS_ID_HIGH (101) */
-#define	CSA	CS(0x14)	/*	- " - POS_102 */
-#define	CSM	CS(0x0e)	/*	- " - POS_103 */
-#define	CSM_FM1	CS(0x16)	/*	- " - POS_103 (copy in FM1) */
-#define	CSI	CS(0x18)	/*	- " - POS_104 */
-#define	CSS	CS(0x1a)	/*	- " - POS_105 */
-#define	CSP_06	CS(0x1c)	/*	- " - POS_106 */
-#define	WDOG_ST		0x1c	/* Watchdog status (FM2 only)	*/
-#define	WDOG_EN		0x1c	/* Watchdog enabling (FM2 only, 8Bit)	*/
-#define	WDOG_DIS	0x1e	/* Watchdog disabling (FM2 only, 8Bit)	*/
-
-#define PGRA	CSM		/* Flash page register */
-
-
-#define	WCTA	FF(0)		/* word counter */
-#define	FFLAG	FF(1)		/* FLAG/V_FULL (FIFO almost full, write only)*/
-
-/*
- * Timer register (FM2 only)
- */
-#define RTM_CNT		0x28		/* RTM Counter */
-#define TI_DIV		0x60		/* Timer Prescaler */
-#define TI_CH1		0x62		/* Timer channel 1 counter */
-#define TI_STOP		0x64		/* Stop timer on channel 1 */
-#define TI_STRT		0x66		/* Start timer on channel 1 */
-#define TI_INI2		0x68		/* Timer: Bus master preemption */
-#define TI_CNT2		0x6a		/* Timer */
-#define TI_INI3		0x6c		/* Timer: Streaming data */
-#define TI_CNT3		0x6e		/* Timer */
-#define WDOG_LO		0x70		/* Watchdog counter low */
-#define WDOG_HI		0x72		/* Watchdog counter high */
-#define RTM_PRE		0x74		/* restr. token prescaler */
-#define RTM_TIM		0x76		/* restr. token timer */
-
-/*
- * Recommended Timeout values (for FM2 timer only)
- */
-#define TOUT_BM_PRE	188		/* 3.76 usec	*/
-#define TOUT_S_DAT	374		/* 7.48 usec	*/
-
-/*
- * CS register (write only)
- */
-#define	HSR(p)	CS(0x18|(p))	/* Host request register */
-
-#define	RTM_PUT		0x36		/* restr. token counter write */
-#define	RTM_GET		0x28		/*	- " -	clear */
-#define	RTM_CLEAR	0x34		/*	- " -	read */
-
-/*
- * BCN	Bit definitions
- */
-#define BCN_BUSY	0x8000		/* DMA Busy flag */
-#define BCN_AZERO	0x4000		/* Almost zero flag (BCN < 4) */
-#define BCN_STREAM	0x2000		/* Allow streaming data (BCN >= 8) */
-
-/*
- * WCN	Bit definitions
- */
-#define WCN_ZERO	0x2000		/* Zero flag (counted to zero) */
-#define WCN_AZERO	0x1000		/* Almost zero flag (BCN < 4) */
-
-/*
- * CNT_TST	Bit definitions
- */
-#define CNT_MODE	0x01		/* Go into test mode */
-#define	CNT_D32		0x02		/* 16/32 BIT test mode */
-
-/*
- * FIFO Flag		FIFO Flags/Vfull register
- */
-#define FF_VFULL	0x003f		/* V_full value mask */
-#define FFLG_FULL	0x2000		/* FULL flag */
-#define FFLG_A_FULL	0x1000		/* Almost full flag */
-#define FFLG_VFULL	0x0800		/* V_full Flag */
-#define FFLG_A_EMP	0x0400		/* almost empty flag */
-#define FFLG_EMP	0x0200		/* empty flag */
-#define FFLG_T_EMP	0x0100		/* totally empty flag */
-
-/*
- * WDOG		Watchdog status register
- */
-#define WDOG_ALM	0x01		/* Watchdog alarm Bit */
-#define WDOG_ACT	0x02		/* Watchdog active Bit */
-
-/*
- * CS(0)	CONTROLS
- */
-#define	CS_CRESET	0x0001
-#define	FIFO_RST	0x0002
-#define	CS_IMSK		0x0004
-#define	EN_IRQ_CHCK	0x0008
-#define	EN_IRQ_TOKEN	0x0010
-#define	EN_IRQ_TC	0x0020
-#define	TOKEN_STATUS	0x0040
-#define	RTM_CHANGE	0x0080
-
-#define	CS_SAS		0x0100
-#define	CS_BYSTAT	0x0200	/* bypass connected (0=conn.) */
-#define	CS_BYPASS	0x0400	/* bypass on/off indication */
-
-/*
- * CS(2)	FIFOSTAT
- */
-#define	HSREQ		0x0007
-#define	BIGDIR		0x0008
-#define	CSF_BUSY_FIFO	0x0010
-#define	CSF_BUSY_DMA	0x0020
-#define	SLOT_32		0x0040
-
-#define	LED_0		0x0001
-#define	LED_1		0x0002
-#define	LED_2		0x0100
-
-#define	MAX_PAGES	8		/* pages */
-#define	MAX_FADDR	0x4000		/* 16K per page */
-
-/*
- *	IRQ = ISRA || ISR2 ;
- *
- *	ISRA = IRQ_OTH_EN && (IS_LAN | IS_BUS) ;
- *	ISR2 = IRQ_TC_EN && IS_TC ;
- *
- *	IS_LAN = (IS_MINTR1 | IS_MINTR2 | IS_PLINT1 | IS_PLINT2 | IS_TIMINT) ||
- *		 (IRQ_EN_TOKEN && IS_TOKEN) ;
- *	IS_BUS = IRQ_CHCK_EN && (IS_BUSERR | IS_CHCK_L) ;
- */
-/*
- *	ISRA	!!! activ high !!!
- */
-#define	IS_MINTR1	0x0001		/* FORMAC ST1U/L & ~IMSK1U/L*/
-#define	IS_MINTR2	0x0002		/* FORMAC ST2U/L & ~IMSK2U/L*/
-#define	IS_PLINT1	0x0004		/* PLC1 */
-#define	IS_PLINT2	0x0008		/* PLC2 */
-#define	IS_TIMINT	0x0010		/* Timer 82C54-2 */
-#define	IS_TOKEN	0x0020		/* restrictet token monitoring */
-#define	IS_CHCK_L	0x0040		/* check line asserted */
-#define	IS_BUSERR	0x0080		/* bus error */
-/*
- *	ISR2
- */
-#define	IS_TC		0x0001		/* terminal count irq */
-#define IS_SFDBKRTN	0x0002		/* selected feedback return */
-#define IS_D16		0x0004		/* DS16 */
-#define	IS_D32		0x0008		/* DS32 */
-#define IS_DPEI		0x0010		/* Data Parity Indication */
-
-#define	ALL_IRSR	0x00ff
-
-#define	FM_A(a)	ADDR(FMA(a))	/* FORMAC Plus physical addr */
-#define	P1_A(a)	ADDR(P1(a))	/* PLC1 (r/w) */
-#define	P2_A(a)	ADDR(P2(a))	/* PLC2 (r/w) (DAS) */
-#define	TI_A(a)	ADDR(TI(a))	/* Timer (r/w) FM1 only! */
-#define	PR_A(a)	ADDR(PR(a))	/* config. PROM */
-#define	CS_A(a)	ADDR(CS(a))	/* control/status */
-
-#define	ISR1_A	ADDR(ISRA)	/* first int. source register address */
-#define	ISR2_A	ADDR(ISR2)	/* second	-"-	 */
-#define	CSR_A	ADDR(CSRA)	/* control/status register address */
-#define	CSF_A	ADDR(CSFA)	/* control/status FIFO BUSY flags (r/w) */
-
-#define	CSIL_A	ADDR(CSIL)	/* I/O mapped POS_ID_low (102) */
-#define	CSIH_A	ADDR(CSIH)	/*	- " - POS_ID_HIGH (101) */
-#define	CSA_A	ADDR(CSA)	/*	- " - POS_102 */
-#define	CSI_A	ADDR(CSI)	/*	- " - POS_104 */
-#define	CSM_A	ADDR(CSM)	/*	- " - POS_103 */
-#define	CSM_FM1_A	ADDR(CSM_FM1)	/*	- " - POS_103 (2nd copy, FM1) */
-#define	CSP_06_A	ADDR(CSP_06)	/*	- " - POS_106 */
-
-#define	WCT_A	ADDR(WCTA)	/* word counter (r/w) */
-#define	FFLAG_A	ADDR(FFLAG)	/* FLAG/V_FULL (FIFO almost full, write only)*/
-
-#define	ACL_A	ADDR(ACLA)	/* address counter low */
-#define	ACH_A	ADDR(ACHA)	/* address counter high */
-#define	BCN_A	ADDR(BCN)	/* byte counter */
-#define	MUX_A	ADDR(MUX)	/* MUX-register */
-
-#define	ISR_A	ADDR(ISRA)	/* Interrupt Source Register */
-#define	FIFO_RESET_A	ADDR(FIFO_RESET)	/* reset the FIFO */
-#define	FIFO_EN_A	ADDR(FIFO_EN)		/* enable the FIFO */
-
-#define WDOG_EN_A	ADDR(WDOG_EN)		/* reset and start the WDOG */
-#define WDOG_DIS_A	ADDR(WDOG_DIS)		/* disable the WDOG */
-/*
- * all control reg. (read!) are 8 bit (except PAGE_RG_A and LEDR_A)
- */
-#define	HSR_A(p)	ADDR(HSR(p))	/* Host request register */
-
-#define	STAT_BYP	0		/* bypass station */
-#define	STAT_INS	2		/* insert station */
-#define	BYPASS(o)	CS(0x10|(o))	/* o=STAT_BYP || STAT_INS */
-
-#define	IRQ_TC_EN	CS(0x0b)	/* enable/disable IRQ on TC */
-#define	IRQ_TC_DIS	CS(0x0a)
-#define	IRQ_TOKEN_EN	CS(9)		/* enable/disable IRQ on restr. Token */
-#define	IRQ_TOKEN_DIS	CS(8)
-#define	IRQ_CHCK_EN	CS(7)		/*	-"-	IRQ after CHCK line */
-#define	IRQ_CHCK_DIS	CS(6)
-#define	IRQ_OTH_EN	CS(5)		/*	-"-	other IRQ's */
-#define	IRQ_OTH_DIS	CS(4)
-#define	FIFO_EN		CS(3)		/* disable (reset), enable FIFO */
-#define	FIFO_RESET	CS(2)
-#define	CARD_EN		CS(1)		/* disable (reset), enable card */
-#define	CARD_DIS	CS(0)
-
-#define	LEDR_A		ADDR(LEDR)	/* D0=green, D1=yellow, D8=L2 */
-#define	PAGE_RG_A	ADDR(CSM)	/* D<2..0> */
-#define	IRQ_CHCK_EN_A	ADDR(IRQ_CHCK_EN)
-#define IRQ_CHCK_DIS_A	ADDR(IRQ_CHCK_DIS)
-
-#define	GET_PAGE(bank)	outpw(PAGE_RG_A,(inpw(PAGE_RG_A) &\
-				(~POS_PAGE)) |(int) (bank))
-#define	VPP_ON()	if (smc->hw.rev == FM1_REV) {	\
-				outpw(PAGE_RG_A,	\
-				(inpw(PAGE_RG_A) & POS_PAGE) | PROG_EN); \
-			}
-#define	VPP_OFF()	if (smc->hw.rev == FM1_REV) {	\
-				outpw(PAGE_RG_A,(inpw(PAGE_RG_A) & POS_PAGE)); \
-			}
-
-#define	SKFDDI_PSZ	16		/* address PROM size */
-
-#define	READ_PROM(a)	((u_char)inp(a))
-
-#define	GET_ISR()	~inpw(ISR1_A)
-#ifndef	TCI
-#define	CHECK_ISR()	~inpw(ISR1_A)
-#define	CHECK_ISR_SMP(iop)	~inpw((iop)+ISRA)
-#else
-#define	CHECK_ISR()		(~inpw(ISR1_A) | ~inpw(ISR2_A))
-#define	CHECK_ISR_SMP(iop)	(~inpw((iop)+ISRA) | ~inpw((iop)+ISR2))
-#endif
-
-#define	DMA_BUSY()	(inpw(CSF_A) & CSF_BUSY_DMA)
-#define	FIFO_BUSY()	(inpw(CSF_A) & CSF_BUSY_FIFO)
-#define	DMA_FIFO_BUSY()	(inpw(CSF_A) & (CSF_BUSY_DMA | CSF_BUSY_FIFO))
-#define	BUS_CHECK() {	int i ; \
-			if ((i = GET_ISR()) & IS_BUSERR) \
-				SMT_PANIC(smc,HWM_E0020,HWM_E0020_MSG) ; \
-			if (i & IS_CHCK_L) \
-				SMT_PANIC(smc,HWM_E0014,HWM_E0014_MSG) ; \
-		}
-
-#define	CHECK_DMA() {	u_long k = 10000 ; \
-		 while (k && (DMA_BUSY())) { \
-			k-- ; \
-			BUS_CHECK() ; \
-		 } \
-		 if (!k) SMT_PANIC(smc,HWM_E0003,HWM_E0003_MSG) ; }
-
-#define	CHECK_FIFO() {u_long k = 1000000 ;\
-		 while (k && (FIFO_BUSY())) k-- ;\
-		 if (!k) SMT_PANIC(smc,HWM_E0019,HWM_E0019_MSG) ; }
-
-#define	CHECK_DMA_FIFO() {u_long k = 1000000 ;\
-		 while (k && (DMA_FIFO_BUSY())) { \
-			k-- ;\
-			BUS_CHECK() ; \
-		 } \
-		 if (!k) SMT_PANIC(smc,HWM_E0004,HWM_E0004_MSG) ; }
-
-#ifndef UNIX
-#define	CLI_FBI()	outp(ADDR(IRQ_OTH_DIS),0)
-#else
-#define	CLI_FBI(smc)	outp(ADDRS((smc),IRQ_OTH_DIS),0)
-#endif
-
-#ifndef	TCI
-#define	CLI_FBI_SMP(iop)	outp((iop)+IRQ_OTH_DIS,0)
-#else
-#define	CLI_FBI_SMP(iop)	outp((iop)+IRQ_OTH_DIS,0) ;\
-				outp((iop)+IRQ_TC_DIS,0)
-#endif
-
-#ifndef UNIX
-#define	STI_FBI()	outp(ADDR(IRQ_OTH_EN),0)
-#else
-#define	STI_FBI(smc)	outp(ADDRS((smc),IRQ_OTH_EN),0)
-#endif
-
-/*
- * Terminal count primitives
- */
-#define CLI_TCI(smc)	outp(ADDRS((smc),IRQ_TC_DIS),0)
-#define STI_TCI(smc)	outp(ADDRS((smc),IRQ_TC_EN),0)
-#define CHECK_TC(smc,k)	{(k) = 10000 ;\
-	while ((k) && (~inpw(ISR2_A) & IS_TC)) (k)-- ;\
-	if (!k) SMT_PANIC(smc,HWM_E0018,HWM_E0018_MSG) ; }
-
-#endif	/* MCA */
-
-#ifdef	ISA
-
-/*
- * address transmission from logic NPADDR6-0 to physical offset address on board
- */
-#define FMA(a)	(0x8000|(((a)&0x07)<<1)|(((a)&0x78)<<7))  /* FORMAC+ (r/w) */
-#define PRA(a)	(0x1000|(((a)&0x07)<<1)|(((a)&0x18)<<7))  /* PROM (read only)*/
-#define P1A(a)	(0x4000|(((a)&0x07)<<1)|(((a)&0x18)<<7))  /* PLC1 (r/w) */
-#define P2A(a)	(0x5000|(((a)&0x07)<<1)|(((a)&0x18)<<7))  /* PLC2 (r/w) */
-#define TIA(a)	(0x6000|(((a)&0x03)<<1))		  /* Timer (r/w) */
-
-#define	ISRA	0x0000		/* int. source register address (read only) */
-#define	ACLA	0x0000		/* address counter low address (write only) */
-#define	ACHA	0x0002		/* address counter high address (write only) */
-#define	TRCA	0x0004		/* transfer counter address (write only) */
-#define	PGRA	0x0006		/* page register address (write only) */
-#define RQAA	0x2000		/* Request reg. (write only) */
-#define	CSRA	0x3000		/* control/status register address (r/w) */
-
-/*
- * physical address offset + IO-Port base address
- */
-#define FM_A(a)	(FMA(a)+smc->hw.iop)	/* FORMAC Plus physical addr */
-#define PR_A(a)	(PRA(a)+smc->hw.iop)	/* PROM (read only)*/
-#define P1_A(a)	(P1A(a)+smc->hw.iop)	/* PLC1 (r/w) */
-#define P2_A(a)	(P2A(a)+smc->hw.iop)	/* PLC2 (r/w) */
-#define TI_A(a)	(TIA(a)+smc->hw.iop)	/* Timer (r/w) */
-
-#define	ISR_A	(0x0000+smc->hw.iop) /* int. source register address (read only) */
-#define	ACL_A	(0x0000+smc->hw.iop) /* address counter low address (write only) */
-#define	ACH_A	(0x0002+smc->hw.iop) /* address counter high address (write only)*/
-#define	TRC_A	(0x0004+smc->hw.iop) /* transfer counter address (write only) */
-#define	PGR_A	(0x0006+smc->hw.iop) /* page register address (write only) */
-#define RQA_A	(0x2000+smc->hw.iop) /* Request reg. (write only) */
-#define	CSR_A	(0x3000+smc->hw.iop) /* control/status register address (r/w) */
-#ifdef UNIX
-#define	CSR_AS(smc) (0x3000+(smc)->hw.iop) /* control/status register address */
-#endif
-#define	PLC1_I	(0x3400+smc->hw.iop) /* clear PLC1 interrupt bit */
-#define	PLC2_I	(0x3800+smc->hw.iop) /* clear PLC2 interrupt bit */
-
-#ifndef	MULT_OEM
-#ifndef	OEM_CONCEPT
-#define	SKLOGO_STR	"SKFDDI"
-#else	/* OEM_CONCEPT */
-#define	SKLOGO_STR	OEM_FDDI_LOGO
-#endif	/* OEM_CONCEPT */
-#endif  /* MULT_OEM */
-#define	SADDRL	(24)		/* start address SKLOGO */
-#define	SA_MAC	(0)		/* start addr. MAC_AD within the PROM */
-#define	PRA_OFF	(0)
-#define SA_PMD_TYPE	(8)	/* start addr. PMD-Type */
-
-#define	CDID	(PRA(SADDRL))	/* Card ID int/O port addr. offset */
-#define	NEXT_CDID	((PRA(SADDRL+1)) - CDID)
-
-#define	SKFDDI_PSZ	32		/* address PROM size */
-
-#define	READ_PROM(a)	((u_char)inpw(a))
-#define	GET_PAGE(i)	outpw(PGR_A,(int)(i))
-
-#define	MAX_PAGES	16		/* 16 pages */
-#define	MAX_FADDR	0x2000		/* 8K per page */
-#define	VPP_OFF()	outpw(CSR_A,(inpw(CSR_A) & (CS_CRESET|CS_BYPASS)))
-#define	VPP_ON()	outpw(CSR_A,(inpw(CSR_A) & (CS_CRESET|CS_BYPASS)) | \
-				CS_VPPSW)
-
-/*
- * control/status register CSRA	bits (log. addr: 0x3000)
- */
-/* write */
-#define CS_CRESET	0x01		/* Card reset (0=reset) */
-#define	CS_IMSK		0x02		/* enable IRQ (1=enable, 0=disable) */
-#define CS_RESINT1	0x04		/* PLINT1 reset */
-#define	CS_VPPSW	0x10		/* 12V power switch (0=off, 1=on) */
-#define CS_BYPASS	0x20		/* bypass switch (0=remove, 1=insert)*/
-#define CS_RESINT2	0x40		/* PLINT2 reset */
-/* read */
-#define	CS_BUSY		0x04		/* master transfer activ (=1) */
-#define	CS_SW_EPROM	0x08		/* 0=Application Soft. 1=BOOT-EPROM */
-#define	CS_BYSTAT	0x40		/* 0=Bypass exist, 1= ..not */
-#define	CS_SAS		0x80		/* single attachement station (=1) */
-
-/*
- * Interrupt source register ISRA (log. addr: 0x0000) read only & low activ.
- */
-#define IS_MINTR1	0x01		/* FORMAC ST1U/L && ~IMSK1U/L*/
-#define IS_MINTR2	0x02		/* FORMAC ST2U/L && ~IMSK2U/L*/
-#define IS_PLINT1	0x04		/* PLC1 */
-#define IS_PLINT2	0x08		/* PLC2 */
-#define IS_TIMINT	0x10		/* Timer 82C54-2 */
-
-#define	ALL_IRSR	(IS_MINTR1|IS_MINTR2|IS_PLINT1|IS_PLINT2|IS_TIMINT)
-
-#define	FPROM_SW()	(inpw(CSR_A)&CS_SW_EPROM)
-#define	DMA_BUSY()	(inpw(CSR_A)&CS_BUSY)
-#define CHECK_FIFO()
-#define	BUS_CHECK()
-
-/*
- * set Host Request register (wr.)
- */
-#define SET_HRQ(qup)	outpw(RQA_A+((qup)<<1),0)
-
-#ifndef UNIX
-#ifndef WINNT
-#define	CLI_FBI()	outpw(CSR_A,(inpw(CSR_A)&(CS_CRESET|CS_BYPASS|CS_VPPSW)))
-#else
-#define	CLI_FBI()	outpw(CSR_A,(l_inpw(CSR_A) & \
-				(CS_CRESET|CS_BYPASS|CS_VPPSW)))
-#endif
-#else
-#define	CLI_FBI(smc)	outpw(CSR_AS(smc),(inpw(CSR_AS(smc))& \
-						(CS_CRESET|CS_BYPASS|CS_VPPSW)))
-#endif
-
-#ifndef UNIX
-#define	STI_FBI()	outpw(CSR_A,(inpw(CSR_A) & \
-				(CS_CRESET|CS_BYPASS|CS_VPPSW)) | CS_IMSK)
-#else
-#define	STI_FBI(smc)	outpw(CSR_AS(smc),(inpw(CSR_AS(smc)) & \
-				(CS_CRESET|CS_BYPASS|CS_VPPSW)) | CS_IMSK)
-#endif
-
-#define CHECK_DMA()	{unsigned k = 10000 ;\
-			while (k && (DMA_BUSY())) k-- ;\
-			if (!k) SMT_PANIC(smc,HWM_E0003,HWM_E0003_MSG) ; }
-
-#define	GET_ISR()	~inpw(ISR_A)
-
-#endif	/* ISA */
-
 /*--------------------------------------------------------------------------*/
 #ifdef	PCI
 
diff --git a/drivers/net/skfp/h/skfbiinc.h b/drivers/net/skfp/h/skfbiinc.h
index 79d55ad2cd2a..ac2d7192f1ca 100644
--- a/drivers/net/skfp/h/skfbiinc.h
+++ b/drivers/net/skfp/h/skfbiinc.h
@@ -22,32 +22,6 @@
  */
 #define ERR_FLAGS (FS_MSRABT | FS_SEAC2 | FS_SFRMERR | FS_SFRMTY1)
 
-#ifdef	ISA
-#define DMA_BUSY_CHECK	CSRA
-#define	IMASK_FAST	(IS_PLINT1 | IS_PLINT2 | IS_TIMINT)
-#define	HRQR		(RQAA+(RQ_RRQ<<1))
-#define	HRQW		(RQAA+(RQ_WA2<<1))
-#define	HRQA0		(RQAA+(RQ_WA0<<1))
-#define HRQSQ		(RQAA+(RQ_WSQ<<1))
-#endif
-
-#ifdef	EISA
-#define	DMA_BUSY_CHECK	CSRA
-#define DMA_HIGH_WORD	0x0400
-#define DMA_MASK_M	0x0a
-#define DMA_MODE_M	0x0b
-#define DMA_BYTE_PTR_M	0x0c
-#define DMA_MASK_S	0x0d4
-#define DMA_MODE_S	0x0d6
-#define DMA_BYTE_PTR_S	0x0d8
-#define	IMASK_FAST	(IS_PLINT1 | IS_PLINT2 | IS_TIMINT | IS_TC)
-#endif	/* EISA */
-
-#ifdef	MCA
-#define	IMASK_FAST	(IS_PLINT1 | IS_PLINT2 | IS_TIMINT | IS_TOKEN | \
-			 IS_CHCK_L | IS_BUSERR)
-#endif
-
 #ifdef PCI
 #define	IMASK_FAST	(IS_PLINT1 | IS_PLINT2 | IS_TIMINT | IS_TOKEN | \
 			 IS_MINTR2 | IS_MINTR3 | IS_R1_P | \
diff --git a/drivers/net/skfp/h/targethw.h b/drivers/net/skfp/h/targethw.h
index 22c4923241d3..626dc7263591 100644
--- a/drivers/net/skfp/h/targethw.h
+++ b/drivers/net/skfp/h/targethw.h
@@ -53,11 +53,6 @@ struct	s_oem_ids {
 	u_char 	oi_sub_id[4] ;		/* sub id bytes, representation as */
 					/* defined by hardware,		*/
 #endif
-#ifdef ISA
-	u_char	oi_logo_len ;		/* the length of the adapter logo */	
-	u_char	oi_logo[6] ;		/* the adapter logo		*/
-	u_char	oi_reserved1 ;
-#endif	/* ISA */
 } ;
 #endif	/* MULT_OEM */
 
@@ -70,43 +65,17 @@ struct s_smt_hw {
 	short	dma ;			/* DMA channel */
 	short	irq ;			/* IRQ level */
 	short	eprom ;			/* FLASH prom */
-#ifndef	PCI
-	short	DmaWriteExtraBytes ;	/* add bytes for DMA write */
-#endif
 
 #ifndef SYNC
 	u_short	n_a_send ;		/* pending send requests */
 #endif
 
-#if	(defined(EISA) || defined(MCA) || defined(PCI))
+#if	defined(PCI)
 	short	slot ;			/* slot number */
 	short   max_slots ;		/* maximum number of slots */
-#endif
-
-#if	(defined(PCI) || defined(MCA))
 	short	wdog_used ;		/* TRUE if the watch dog is used */
 #endif
 
-#ifdef	MCA
-	short	slot_32 ;		/* 32bit slot (1) or 16bit slot (0) */
-	short	rev ;			/* Board revision (FMx_REV). */
-	short	VFullRead ;		/* V_full value for DMA read */
-	short	VFullWrite ;		/* V_full value for DMA write */
-#endif
-
-#ifdef	EISA
-	short	led ;			/* LED for FE card */
-
-	short	dma_rmode ;		/* read mode */
-	short	dma_wmode ;		/* write mode */
-	short	dma_emode ;		/* extend mode */
-
-	/* DMA controller channel dependent io addresses */
-	u_short dma_base_word_count ;
-	u_short dma_base_address ;
-	u_short dma_base_address_page ;
-#endif
-
 #ifdef	PCI
 	u_short	pci_handle ;		/* handle to access the BIOS func */
 	u_long	is_imask ;		/* int maske for the int source reg */