Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-09-01

This series contains updates to i40e, ixgbe and ixgbevf.

Anjali fixes a bug in i40e where the port is not receiving multicast or VLAN
tagged packets in promiscuous mode.  Which can occur when a software bridge
is created on top of the device.

Don adds support in ixgbe that indicates the presence of management firmware.
Added support for entering low power link up state on devices that support
it when the device is closing or suspending.  Updated the driver to report
unknown bus speed and width since IOSF does not report a PCIe bus speed or
width for X550 devices.  Also added the new bus type for integrated I/O
interface (IOSF).  Cleaned up of redundant code in ixgbe.

Mark adds support for UDP-encapsulation transmit checksum and for VXLAN
receive offloads.  Introduces a helper function to do the register access
and processing to avoid needless PHY access on copper PHYs.  Added support
for reporting 2.5G link speed.  Fixed warnings resulting from redundant
initializations of the get_bus_info field.

Maninder Singh updates the ixgbe driver to use kzalloc instead of kcalloc
for allocation of one thing.

Tom Barbette adds support for ethtool to change the rxfh indirection table
and/or key using ethtool interface.

Emil resolves an issue where users were not able to dynamically set number
of queues for 82598 via ethtool -L.

Alex Williamson removes bimodal SR-IOV disabling behavior since it is
confusing to users and results in a state where the PF is broken for other
uses unless the user sets sriov_numvfs to zero prior to unbinding the
device.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 179 insertions, 3 deletions

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 7581da13e92a..9fe9445cd73b 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -26,6 +26,20 @@
 #include "ixgbe_common.h"
 #include "ixgbe_phy.h"
 
+static s32 ixgbe_get_invariants_X550_x(struct ixgbe_hw *hw)
+{
+	struct ixgbe_mac_info *mac = &hw->mac;
+	struct ixgbe_phy_info *phy = &hw->phy;
+
+	/* Start with X540 invariants, since so simular */
+	ixgbe_get_invariants_X540(hw);
+
+	if (mac->ops.get_media_type(hw) != ixgbe_media_type_copper)
+		phy->ops.set_phy_power = NULL;
+
+	return 0;
+}
+
 /** ixgbe_setup_mux_ctl - Setup ESDP register for I2C mux control
  *  @hw: pointer to hardware structure
  **/
@@ -597,6 +611,24 @@ static s32 ixgbe_update_flash_X550(struct ixgbe_hw *hw)
 	return status;
 }
 
+/**
+ * ixgbe_get_bus_info_X550em - Set PCI bus info
+ * @hw: pointer to hardware structure
+ *
+ * Sets bus link width and speed to unknown because X550em is
+ * not a PCI device.
+ **/
+static s32 ixgbe_get_bus_info_X550em(struct ixgbe_hw *hw)
+{
+	hw->bus.type  = ixgbe_bus_type_internal;
+	hw->bus.width = ixgbe_bus_width_unknown;
+	hw->bus.speed = ixgbe_bus_speed_unknown;
+
+	hw->mac.ops.set_lan_id(hw);
+
+	return 0;
+}
+
 /** ixgbe_disable_rx_x550 - Disable RX unit
  *
  *  Enables the Rx DMA unit for x550
@@ -1444,6 +1476,144 @@ static s32 ixgbe_reset_phy_t_X550em(struct ixgbe_hw *hw)
 	return ixgbe_enable_lasi_ext_t_x550em(hw);
 }
 
+/** ixgbe_get_lcd_x550em - Determine lowest common denominator
+ *  @hw: pointer to hardware structure
+ *  @lcd_speed: pointer to lowest common link speed
+ *
+ *  Determine lowest common link speed with link partner.
+ **/
+static s32 ixgbe_get_lcd_t_x550em(struct ixgbe_hw *hw,
+				  ixgbe_link_speed *lcd_speed)
+{
+	u16 an_lp_status;
+	s32 status;
+	u16 word = hw->eeprom.ctrl_word_3;
+
+	*lcd_speed = IXGBE_LINK_SPEED_UNKNOWN;
+
+	status = hw->phy.ops.read_reg(hw, IXGBE_AUTO_NEG_LP_STATUS,
+				      IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+				      &an_lp_status);
+	if (status)
+		return status;
+
+	/* If link partner advertised 1G, return 1G */
+	if (an_lp_status & IXGBE_AUTO_NEG_LP_1000BASE_CAP) {
+		*lcd_speed = IXGBE_LINK_SPEED_1GB_FULL;
+		return status;
+	}
+
+	/* If 10G disabled for LPLU via NVM D10GMP, then return no valid LCD */
+	if ((hw->bus.lan_id && (word & NVM_INIT_CTRL_3_D10GMP_PORT1)) ||
+	    (word & NVM_INIT_CTRL_3_D10GMP_PORT0))
+		return status;
+
+	/* Link partner not capable of lower speeds, return 10G */
+	*lcd_speed = IXGBE_LINK_SPEED_10GB_FULL;
+	return status;
+}
+
+/** ixgbe_enter_lplu_x550em - Transition to low power states
+ *  @hw: pointer to hardware structure
+ *
+ *  Configures Low Power Link Up on transition to low power states
+ *  (from D0 to non-D0). Link is required to enter LPLU so avoid resetting
+ *  the X557 PHY immediately prior to entering LPLU.
+ **/
+static s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
+{
+	u16 an_10g_cntl_reg, autoneg_reg, speed;
+	s32 status;
+	ixgbe_link_speed lcd_speed;
+	u32 save_autoneg;
+	bool link_up;
+
+	/* SW LPLU not required on later HW revisions. */
+	if (IXGBE_FUSES0_REV1 & IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0)))
+		return 0;
+
+	/* If blocked by MNG FW, then don't restart AN */
+	if (ixgbe_check_reset_blocked(hw))
+		return 0;
+
+	status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
+	if (status)
+		return status;
+
+	status = hw->eeprom.ops.read(hw, NVM_INIT_CTRL_3,
+				     &hw->eeprom.ctrl_word_3);
+	if (status)
+		return status;
+
+	/* If link is down, LPLU disabled in NVM, WoL disabled, or
+	 * manageability disabled, then force link down by entering
+	 * low power mode.
+	 */
+	if (!link_up || !(hw->eeprom.ctrl_word_3 & NVM_INIT_CTRL_3_LPLU) ||
+	    !(hw->wol_enabled || ixgbe_mng_present(hw)))
+		return ixgbe_set_copper_phy_power(hw, false);
+
+	/* Determine LCD */
+	status = ixgbe_get_lcd_t_x550em(hw, &lcd_speed);
+	if (status)
+		return status;
+
+	/* If no valid LCD link speed, then force link down and exit. */
+	if (lcd_speed == IXGBE_LINK_SPEED_UNKNOWN)
+		return ixgbe_set_copper_phy_power(hw, false);
+
+	status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
+				      IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+				      &speed);
+	if (status)
+		return status;
+
+	/* If no link now, speed is invalid so take link down */
+	status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
+	if (status)
+		return ixgbe_set_copper_phy_power(hw, false);
+
+	/* clear everything but the speed bits */
+	speed &= IXGBE_MDIO_AUTO_NEG_VEN_STAT_SPEED_MASK;
+
+	/* If current speed is already LCD, then exit. */
+	if (((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB) &&
+	     (lcd_speed == IXGBE_LINK_SPEED_1GB_FULL)) ||
+	    ((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB) &&
+	     (lcd_speed == IXGBE_LINK_SPEED_10GB_FULL)))
+		return status;
+
+	/* Clear AN completed indication */
+	status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM,
+				      IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+				      &autoneg_reg);
+	if (status)
+		return status;
+
+	status = hw->phy.ops.read_reg(hw, IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG,
+				      IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+				      &an_10g_cntl_reg);
+	if (status)
+		return status;
+
+	status = hw->phy.ops.read_reg(hw,
+				      IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG,
+				      IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+				      &autoneg_reg);
+	if (status)
+		return status;
+
+	save_autoneg = hw->phy.autoneg_advertised;
+
+	/* Setup link at least common link speed */
+	status = hw->mac.ops.setup_link(hw, lcd_speed, false);
+
+	/* restore autoneg from before setting lplu speed */
+	hw->phy.autoneg_advertised = save_autoneg;
+
+	return status;
+}
+
 /** ixgbe_init_phy_ops_X550em - PHY/SFP specific init
  *  @hw: pointer to hardware structure
  *
@@ -1514,6 +1684,11 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
 			ret_val = ixgbe_setup_kr_speed_x550em(hw, speed);
 		}
 
+		/* setup SW LPLU only for first revision */
+		if (!(IXGBE_FUSES0_REV1 & IXGBE_READ_REG(hw,
+							IXGBE_FUSES0_GROUP(0))))
+			phy->ops.enter_lplu = ixgbe_enter_lplu_t_x550em;
+
 		phy->ops.handle_lasi = ixgbe_handle_lasi_ext_t_x550em;
 		phy->ops.reset = ixgbe_reset_phy_t_X550em;
 		break;
@@ -1760,7 +1935,6 @@ static void ixgbe_set_source_address_pruning_X550(struct ixgbe_hw *hw,
 	.get_mac_addr			= &ixgbe_get_mac_addr_generic, \
 	.get_device_caps		= &ixgbe_get_device_caps_generic, \
 	.stop_adapter			= &ixgbe_stop_adapter_generic, \
-	.get_bus_info			= &ixgbe_get_bus_info_generic, \
 	.set_lan_id			= &ixgbe_set_lan_id_multi_port_pcie, \
 	.read_analog_reg8		= NULL, \
 	.write_analog_reg8		= NULL, \
@@ -1809,6 +1983,7 @@ static struct ixgbe_mac_operations mac_ops_X550 = {
 	.get_wwn_prefix		= &ixgbe_get_wwn_prefix_generic,
 	.setup_link		= &ixgbe_setup_mac_link_X540,
 	.get_link_capabilities	= &ixgbe_get_copper_link_capabilities_generic,
+	.get_bus_info		= &ixgbe_get_bus_info_generic,
 	.setup_sfp		= NULL,
 };
 
@@ -1820,6 +1995,7 @@ static struct ixgbe_mac_operations mac_ops_X550EM_x = {
 	.get_wwn_prefix		= NULL,
 	.setup_link		= NULL, /* defined later */
 	.get_link_capabilities	= &ixgbe_get_link_capabilities_X550em,
+	.get_bus_info		= &ixgbe_get_bus_info_X550em,
 	.setup_sfp		= ixgbe_setup_sfp_modules_X550em,
 
 };
@@ -1855,7 +2031,7 @@ static struct ixgbe_eeprom_operations eeprom_ops_X550EM_x = {
 	.read_reg		= &ixgbe_read_phy_reg_generic, \
 	.write_reg		= &ixgbe_write_phy_reg_generic, \
 	.setup_link		= &ixgbe_setup_phy_link_generic, \
-	.set_phy_power		= &ixgbe_set_copper_phy_power, \
+	.set_phy_power		= NULL, \
 	.check_overtemp		= &ixgbe_tn_check_overtemp, \
 	.get_firmware_version	= &ixgbe_get_phy_firmware_version_generic,
 
@@ -1893,7 +2069,7 @@ struct ixgbe_info ixgbe_X550_info = {
 
 struct ixgbe_info ixgbe_X550EM_x_info = {
 	.mac			= ixgbe_mac_X550EM_x,
-	.get_invariants		= &ixgbe_get_invariants_X540,
+	.get_invariants		= &ixgbe_get_invariants_X550_x,
 	.mac_ops		= &mac_ops_X550EM_x,
 	.eeprom_ops		= &eeprom_ops_X550EM_x,
 	.phy_ops		= &phy_ops_X550EM_x,