mtd: nand: denali: avoid hard-coding ECC step, strength, bytes

This driver was originally written for the Intel MRST platform with
several platform-specific parameters hard-coded.

Currently, the ECC settings are hard-coded as follows:

  #define ECC_SECTOR_SIZE 512
  #define ECC_8BITS       14
  #define ECC_15BITS      26

Therefore, the driver can only support two cases.
 - ecc.size = 512, ecc.strength = 8    --> ecc.bytes = 14
 - ecc.size = 512, ecc.strength = 15   --> ecc.bytes = 26

However, these are actually customizable parameters, for example,
UniPhier platform supports the following:

 - ecc.size = 1024, ecc.strength = 8   --> ecc.bytes = 14
 - ecc.size = 1024, ecc.strength = 16  --> ecc.bytes = 28
 - ecc.size = 1024, ecc.strength = 24  --> ecc.bytes = 42

So, we need to handle the ECC parameters in a more generic manner.
Fortunately, the Denali User's Guide explains how to calculate the
ecc.bytes.  The formula is:

  ecc.bytes = 2 * CEIL(13 * ecc.strength / 16)  (for ecc.size = 512)
  ecc.bytes = 2 * CEIL(14 * ecc.strength / 16)  (for ecc.size = 1024)

For DT platforms, it would be reasonable to allow DT to specify ECC
strength by either "nand-ecc-strength" or "nand-ecc-maximize".  If
none of them is specified, the driver will try to meet the chip's ECC
requirement.

For PCI platforms, the max ECC strength is used to keep the original
behavior.

Newer versions of this IP need ecc.size and ecc.steps explicitly
set up via the following registers:
  CFG_DATA_BLOCK_SIZE       (0x6b0)
  CFG_LAST_DATA_BLOCK_SIZE  (0x6c0)
  CFG_NUM_DATA_BLOCKS       (0x6d0)

For older IP versions, write accesses to these registers are just
ignored.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

1 files changed, 4 insertions, 0 deletions

diff --git a/drivers/mtd/nand/denali_pci.c b/drivers/mtd/nand/denali_pci.c
index ac843238b77e..37dc0934c24c 100644
--- a/drivers/mtd/nand/denali_pci.c
+++ b/drivers/mtd/nand/denali_pci.c
@@ -27,6 +27,8 @@ static const struct pci_device_id denali_pci_ids[] = {
 };
 MODULE_DEVICE_TABLE(pci, denali_pci_ids);
 
+NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);
+
 static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 {
 	int ret;
@@ -65,6 +67,8 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	pci_set_master(dev);
 	denali->dev = &dev->dev;
 	denali->irq = dev->irq;
+	denali->ecc_caps = &denali_pci_ecc_caps;
+	denali->nand.ecc.options |= NAND_ECC_MAXIMIZE;
 
 	ret = pci_request_regions(dev, DENALI_NAND_NAME);
 	if (ret) {