mmc: atmel-mci: move atmel-mci-regs.h content in atmel-mci.c

atmel-mci-regs.h is only included in atmel-mci.c so move its content in
the driver and do some cleanup in these definitions to remove checkpatch
errors.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

1 files changed, 149 insertions, 1 deletions

diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index bf62e429f7fc..9f3bb611000f 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -44,7 +44,155 @@
 #include <asm/io.h>
 #include <asm/unaligned.h>
 
-#include "atmel-mci-regs.h"
+/*
+ * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
+ * Registers and bitfields marked with [2] are only available in MCI2
+ */
+
+/* MCI Register Definitions */
+#define	ATMCI_CR			0x0000	/* Control */
+#define		ATMCI_CR_MCIEN			BIT(0)		/* MCI Enable */
+#define		ATMCI_CR_MCIDIS			BIT(1)		/* MCI Disable */
+#define		ATMCI_CR_PWSEN			BIT(2)		/* Power Save Enable */
+#define		ATMCI_CR_PWSDIS			BIT(3)		/* Power Save Disable */
+#define		ATMCI_CR_SWRST			BIT(7)		/* Software Reset */
+#define	ATMCI_MR			0x0004	/* Mode */
+#define		ATMCI_MR_CLKDIV(x)		((x) <<  0)	/* Clock Divider */
+#define		ATMCI_MR_PWSDIV(x)		((x) <<  8)	/* Power Saving Divider */
+#define		ATMCI_MR_RDPROOF		BIT(11)		/* Read Proof */
+#define		ATMCI_MR_WRPROOF		BIT(12)		/* Write Proof */
+#define		ATMCI_MR_PDCFBYTE		BIT(13)		/* Force Byte Transfer */
+#define		ATMCI_MR_PDCPADV		BIT(14)		/* Padding Value */
+#define		ATMCI_MR_PDCMODE		BIT(15)		/* PDC-oriented Mode */
+#define		ATMCI_MR_CLKODD(x)		((x) << 16)	/* LSB of Clock Divider */
+#define	ATMCI_DTOR			0x0008	/* Data Timeout */
+#define		ATMCI_DTOCYC(x)			((x) <<  0)	/* Data Timeout Cycles */
+#define		ATMCI_DTOMUL(x)			((x) <<  4)	/* Data Timeout Multiplier */
+#define	ATMCI_SDCR			0x000c	/* SD Card / SDIO */
+#define		ATMCI_SDCSEL_SLOT_A		(0 <<  0)	/* Select SD slot A */
+#define		ATMCI_SDCSEL_SLOT_B		(1 <<  0)	/* Select SD slot A */
+#define		ATMCI_SDCSEL_MASK		(3 <<  0)
+#define		ATMCI_SDCBUS_1BIT		(0 <<  6)	/* 1-bit data bus */
+#define		ATMCI_SDCBUS_4BIT		(2 <<  6)	/* 4-bit data bus */
+#define		ATMCI_SDCBUS_8BIT		(3 <<  6)	/* 8-bit data bus[2] */
+#define		ATMCI_SDCBUS_MASK		(3 <<  6)
+#define	ATMCI_ARGR			0x0010	/* Command Argument */
+#define	ATMCI_CMDR			0x0014	/* Command */
+#define		ATMCI_CMDR_CMDNB(x)		((x) <<  0)	/* Command Opcode */
+#define		ATMCI_CMDR_RSPTYP_NONE		(0 <<  6)	/* No response */
+#define		ATMCI_CMDR_RSPTYP_48BIT		(1 <<  6)	/* 48-bit response */
+#define		ATMCI_CMDR_RSPTYP_136BIT	(2 <<  6)	/* 136-bit response */
+#define		ATMCI_CMDR_SPCMD_INIT		(1 <<  8)	/* Initialization command */
+#define		ATMCI_CMDR_SPCMD_SYNC		(2 <<  8)	/* Synchronized command */
+#define		ATMCI_CMDR_SPCMD_INT		(4 <<  8)	/* Interrupt command */
+#define		ATMCI_CMDR_SPCMD_INTRESP	(5 <<  8)	/* Interrupt response */
+#define		ATMCI_CMDR_OPDCMD		(1 << 11)	/* Open Drain */
+#define		ATMCI_CMDR_MAXLAT_5CYC		(0 << 12)	/* Max latency 5 cycles */
+#define		ATMCI_CMDR_MAXLAT_64CYC		(1 << 12)	/* Max latency 64 cycles */
+#define		ATMCI_CMDR_START_XFER		(1 << 16)	/* Start data transfer */
+#define		ATMCI_CMDR_STOP_XFER		(2 << 16)	/* Stop data transfer */
+#define		ATMCI_CMDR_TRDIR_WRITE		(0 << 18)	/* Write data */
+#define		ATMCI_CMDR_TRDIR_READ		(1 << 18)	/* Read data */
+#define		ATMCI_CMDR_BLOCK		(0 << 19)	/* Single-block transfer */
+#define		ATMCI_CMDR_MULTI_BLOCK		(1 << 19)	/* Multi-block transfer */
+#define		ATMCI_CMDR_STREAM		(2 << 19)	/* MMC Stream transfer */
+#define		ATMCI_CMDR_SDIO_BYTE		(4 << 19)	/* SDIO Byte transfer */
+#define		ATMCI_CMDR_SDIO_BLOCK		(5 << 19)	/* SDIO Block transfer */
+#define		ATMCI_CMDR_SDIO_SUSPEND		(1 << 24)	/* SDIO Suspend Command */
+#define		ATMCI_CMDR_SDIO_RESUME		(2 << 24)	/* SDIO Resume Command */
+#define	ATMCI_BLKR			0x0018	/* Block */
+#define		ATMCI_BCNT(x)			((x) <<  0)	/* Data Block Count */
+#define		ATMCI_BLKLEN(x)			((x) << 16)	/* Data Block Length */
+#define	ATMCI_CSTOR			0x001c	/* Completion Signal Timeout[2] */
+#define		ATMCI_CSTOCYC(x)		((x) <<  0)	/* CST cycles */
+#define		ATMCI_CSTOMUL(x)		((x) <<  4)	/* CST multiplier */
+#define	ATMCI_RSPR			0x0020	/* Response 0 */
+#define	ATMCI_RSPR1			0x0024	/* Response 1 */
+#define	ATMCI_RSPR2			0x0028	/* Response 2 */
+#define	ATMCI_RSPR3			0x002c	/* Response 3 */
+#define	ATMCI_RDR			0x0030	/* Receive Data */
+#define	ATMCI_TDR			0x0034	/* Transmit Data */
+#define	ATMCI_SR			0x0040	/* Status */
+#define	ATMCI_IER			0x0044	/* Interrupt Enable */
+#define	ATMCI_IDR			0x0048	/* Interrupt Disable */
+#define	ATMCI_IMR			0x004c	/* Interrupt Mask */
+#define		ATMCI_CMDRDY			BIT(0)		/* Command Ready */
+#define		ATMCI_RXRDY			BIT(1)		/* Receiver Ready */
+#define		ATMCI_TXRDY			BIT(2)		/* Transmitter Ready */
+#define		ATMCI_BLKE			BIT(3)		/* Data Block Ended */
+#define		ATMCI_DTIP			BIT(4)		/* Data Transfer In Progress */
+#define		ATMCI_NOTBUSY			BIT(5)		/* Data Not Busy */
+#define		ATMCI_ENDRX			BIT(6)		/* End of RX Buffer */
+#define		ATMCI_ENDTX			BIT(7)		/* End of TX Buffer */
+#define		ATMCI_SDIOIRQA			BIT(8)		/* SDIO IRQ in slot A */
+#define		ATMCI_SDIOIRQB			BIT(9)		/* SDIO IRQ in slot B */
+#define		ATMCI_SDIOWAIT			BIT(12)		/* SDIO Read Wait Operation Status */
+#define		ATMCI_CSRCV			BIT(13)		/* CE-ATA Completion Signal Received */
+#define		ATMCI_RXBUFF			BIT(14)		/* RX Buffer Full */
+#define		ATMCI_TXBUFE			BIT(15)		/* TX Buffer Empty */
+#define		ATMCI_RINDE			BIT(16)		/* Response Index Error */
+#define		ATMCI_RDIRE			BIT(17)		/* Response Direction Error */
+#define		ATMCI_RCRCE			BIT(18)		/* Response CRC Error */
+#define		ATMCI_RENDE			BIT(19)		/* Response End Bit Error */
+#define		ATMCI_RTOE			BIT(20)		/* Response Time-Out Error */
+#define		ATMCI_DCRCE			BIT(21)		/* Data CRC Error */
+#define		ATMCI_DTOE			BIT(22)		/* Data Time-Out Error */
+#define		ATMCI_CSTOE			BIT(23)		/* Completion Signal Time-out Error */
+#define		ATMCI_BLKOVRE			BIT(24)		/* DMA Block Overrun Error */
+#define		ATMCI_DMADONE			BIT(25)		/* DMA Transfer Done */
+#define		ATMCI_FIFOEMPTY			BIT(26)		/* FIFO Empty Flag */
+#define		ATMCI_XFRDONE			BIT(27)		/* Transfer Done Flag */
+#define		ATMCI_ACKRCV			BIT(28)		/* Boot Operation Acknowledge Received */
+#define		ATMCI_ACKRCVE			BIT(29)		/* Boot Operation Acknowledge Error */
+#define		ATMCI_OVRE			BIT(30)		/* RX Overrun Error */
+#define		ATMCI_UNRE			BIT(31)		/* TX Underrun Error */
+#define	ATMCI_DMA			0x0050	/* DMA Configuration[2] */
+#define		ATMCI_DMA_OFFSET(x)		((x) <<  0)	/* DMA Write Buffer Offset */
+#define		ATMCI_DMA_CHKSIZE(x)		((x) <<  4)	/* DMA Channel Read and Write Chunk Size */
+#define		ATMCI_DMAEN			BIT(8)	/* DMA Hardware Handshaking Enable */
+#define	ATMCI_CFG			0x0054	/* Configuration[2] */
+#define		ATMCI_CFG_FIFOMODE_1DATA	BIT(0)		/* MCI Internal FIFO control mode */
+#define		ATMCI_CFG_FERRCTRL_COR		BIT(4)		/* Flow Error flag reset control mode */
+#define		ATMCI_CFG_HSMODE		BIT(8)		/* High Speed Mode */
+#define		ATMCI_CFG_LSYNC			BIT(12)		/* Synchronize on the last block */
+#define	ATMCI_WPMR			0x00e4	/* Write Protection Mode[2] */
+#define		ATMCI_WP_EN			BIT(0)		/* WP Enable */
+#define		ATMCI_WP_KEY			(0x4d4349 << 8)	/* WP Key */
+#define	ATMCI_WPSR			0x00e8	/* Write Protection Status[2] */
+#define		ATMCI_GET_WP_VS(x)		((x) & 0x0f)
+#define		ATMCI_GET_WP_VSRC(x)		(((x) >> 8) & 0xffff)
+#define	ATMCI_VERSION			0x00FC  /* Version */
+#define	ATMCI_FIFO_APERTURE		0x0200	/* FIFO Aperture[2] */
+
+/* This is not including the FIFO Aperture on MCI2 */
+#define	ATMCI_REGS_SIZE		0x100
+
+/* Register access macros */
+#define	atmci_readl(port, reg)				\
+	__raw_readl((port)->regs + reg)
+#define	atmci_writel(port, reg, value)			\
+	__raw_writel((value), (port)->regs + reg)
+
+/* On AVR chips the Peripheral DMA Controller is not connected to MCI. */
+#ifdef CONFIG_AVR32
+#	define ATMCI_PDC_CONNECTED	0
+#else
+#	define ATMCI_PDC_CONNECTED	1
+#endif
+
+/*
+ * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
+ * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
+ *
+ * This can be done by finding most significant bit set.
+ */
+static inline unsigned int atmci_convert_chksize(unsigned int maxburst)
+{
+	if (maxburst > 1)
+		return fls(maxburst) - 2;
+	else
+		return 0;
+}
 
 #define AUTOSUSPEND_DELAY	50