[PATCH] IB/ipath - program intconfig register using new HT irq hook

Eric's changes to the htirq infrastructure require corresponding
modifications to the ipath HT driver code so that interrupts are still
delivered properly.

Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

1 files changed, 49 insertions, 68 deletions

diff --git a/drivers/infiniband/hw/ipath/ipath_iba6110.c b/drivers/infiniband/hw/ipath/ipath_iba6110.c
index 9e4e8d4c6e20..e57c7a351cb5 100644
--- a/drivers/infiniband/hw/ipath/ipath_iba6110.c
+++ b/drivers/infiniband/hw/ipath/ipath_iba6110.c
@@ -38,6 +38,7 @@
 
 #include <linux/pci.h>
 #include <linux/delay.h>
+#include <linux/htirq.h>
 
 #include "ipath_kernel.h"
 #include "ipath_registers.h"
@@ -913,49 +914,40 @@ static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev,
 	}
 }
 
-static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev,
-			    int pos)
+static int ipath_ht_intconfig(struct ipath_devdata *dd)
 {
-	u32 int_handler_addr_lower;
-	u32 int_handler_addr_upper;
-	u64 ihandler;
-	u32 intvec;
+	int ret;
 
-	/* use indirection register to get the intr handler */
-	pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10);
-	pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower);
-	pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11);
-	pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper);
+	if (dd->ipath_intconfig) {
+		ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
+				 dd->ipath_intconfig);	/* interrupt address */
+		ret = 0;
+	} else {
+		ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
+			      "interrupt address\n");
+		ret = -EINVAL;
+	}
 
-	ihandler = (u64) int_handler_addr_lower |
-		((u64) int_handler_addr_upper << 32);
+	return ret;
+}
+
+static void ipath_ht_irq_update(struct pci_dev *dev, int irq,
+				struct ht_irq_msg *msg)
+{
+	struct ipath_devdata *dd = pci_get_drvdata(dev);
+	u64 prev_intconfig = dd->ipath_intconfig;
+
+	dd->ipath_intconfig = msg->address_lo;
+	dd->ipath_intconfig |= ((u64) msg->address_hi) << 32;
 
 	/*
-	 * kernels with CONFIG_PCI_MSI set the vector in the irq field of
-	 * struct pci_device, so we use that to program the internal
-	 * interrupt register (not config space) with that value. The BIOS
-	 * must still have done the basic MSI setup.
-	 */
-	intvec = pdev->irq;
-	/*
-	 * clear any vector bits there; normally not set but we'll overload
-	 * this for some debug purposes (setting the HTC debug register
-	 * value from software, rather than GPIOs), so it might be set on a
-	 * driver reload.
+	 * If the previous value of dd->ipath_intconfig is zero, we're
+	 * getting configured for the first time, and must not program the
+	 * intconfig register here (it will be programmed later, when the
+	 * hardware is ready).  Otherwise, we should.
 	 */
-	ihandler &= ~0xff0000;
-	/* x86 vector goes in intrinfo[23:16] */
-	ihandler |= intvec << 16;
-	ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, "
-		   "interruptconfig %llx\n", int_handler_addr_lower,
-		   int_handler_addr_upper, intvec,
-		   (unsigned long long) ihandler);
-
-	/* can't program yet, so save for interrupt setup */
-	dd->ipath_intconfig = ihandler;
-	/* keep going, so we find link control stuff also */
-
-	return ihandler != 0;
+	if (prev_intconfig)
+		ipath_ht_intconfig(dd);
 }
 
 /**
@@ -971,12 +963,19 @@ static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev,
 static int ipath_setup_ht_config(struct ipath_devdata *dd,
 				 struct pci_dev *pdev)
 {
-	int pos, ret = 0;
-	int ihandler = 0;
+	int pos, ret;
+
+	ret = __ht_create_irq(pdev, 0, ipath_ht_irq_update);
+	if (ret < 0) {
+		ipath_dev_err(dd, "Couldn't create interrupt handler: "
+			      "err %d\n", ret);
+		goto bail;
+	}
+	dd->ipath_irq = ret;
+	ret = 0;
 
 	/*
-	 * Read the capability info to find the interrupt info, and also
-	 * handle clearing CRC errors in linkctrl register if necessary.  We
+	 * Handle clearing CRC errors in linkctrl register if necessary.  We
 	 * do this early, before we ever enable errors or hardware errors,
 	 * mostly to avoid causing the chip to enter freeze mode.
 	 */
@@ -1000,17 +999,9 @@ static int ipath_setup_ht_config(struct ipath_devdata *dd,
 		}
 		if (!(cap_type & 0xE0))
 			slave_or_pri_blk(dd, pdev, pos, cap_type);
-		else if (cap_type == HT_INTR_DISC_CONFIG)
-			ihandler = set_int_handler(dd, pdev, pos);
 	} while ((pos = pci_find_next_capability(pdev, pos,
 						 PCI_CAP_ID_HT)));
 
-	if (!ihandler) {
-		ipath_dev_err(dd, "Couldn't find interrupt handler in "
-			      "config space\n");
-		ret = -ENODEV;
-	}
-
 bail:
 	return ret;
 }
@@ -1360,25 +1351,6 @@ static void ipath_ht_quiet_serdes(struct ipath_devdata *dd)
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
 }
 
-static int ipath_ht_intconfig(struct ipath_devdata *dd)
-{
-	int ret;
-
-	if (!dd->ipath_intconfig) {
-		ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
-			      "interrupt address\n");
-		ret = 1;
-		goto bail;
-	}
-
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
-			 dd->ipath_intconfig);	/* interrupt address */
-	ret = 0;
-
-bail:
-	return ret;
-}
-
 /**
  * ipath_pe_put_tid - write a TID in chip
  * @dd: the infinipath device
@@ -1575,6 +1547,14 @@ static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase)
 	return 0;
 }
 
+static void ipath_ht_free_irq(struct ipath_devdata *dd)
+{
+	free_irq(dd->ipath_irq, dd);
+	ht_destroy_irq(dd->ipath_irq);
+	dd->ipath_irq = 0;
+	dd->ipath_intconfig = 0;
+}
+
 /**
  * ipath_init_iba6110_funcs - set up the chip-specific function pointers
  * @dd: the infinipath device
@@ -1598,6 +1578,7 @@ void ipath_init_iba6110_funcs(struct ipath_devdata *dd)
 	dd->ipath_f_cleanup = ipath_setup_ht_cleanup;
 	dd->ipath_f_setextled = ipath_setup_ht_setextled;
 	dd->ipath_f_get_base_info = ipath_ht_get_base_info;
+	dd->ipath_f_free_irq = ipath_ht_free_irq;
 
 	/*
 	 * initialize chip-specific variables