Merge tag 'drm-misc-next-fixes-2018-10-31' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

- Properly label Innolux TV123WAM as P120ZDG-BF1 (Doug)
- Add optional delay for panels without hpd hooked up (which solves the
  mystery delay for TI SN65DSI86 bridge) (Doug)
- Another 6bpc quirk for BOE panel 0x0771 (Shawn)

Cc: Doug Anderson <dianders@chromium.org>
Cc: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031201944.GA262020@art_vandelay

3 files changed, 39 insertions, 22 deletions

diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi86.c b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
index f8a931cf3665..680566d97adc 100644
--- a/drivers/gpu/drm/bridge/ti-sn65dsi86.c
+++ b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
@@ -458,18 +458,6 @@ static void ti_sn_bridge_enable(struct drm_bridge *bridge)
 	unsigned int val;
 	int ret;
 
-	/*
-	 * FIXME:
-	 * This 70ms was found necessary by experimentation. If it's not
-	 * present, link training fails. It seems like it can go anywhere from
-	 * pre_enable() up to semi-auto link training initiation below.
-	 *
-	 * Neither the datasheet for the bridge nor the panel tested mention a
-	 * delay of this magnitude in the timing requirements. So for now, add
-	 * the mystery delay until someone figures out a better fix.
-	 */
-	msleep(70);
-
 	/* DSI_A lane config */
 	val = CHA_DSI_LANES(4 - pdata->dsi->lanes);
 	regmap_update_bits(pdata->regmap, SN_DSI_LANES_REG,
@@ -536,7 +524,22 @@ static void ti_sn_bridge_pre_enable(struct drm_bridge *bridge)
 	/* configure bridge ref_clk */
 	ti_sn_bridge_set_refclk_freq(pdata);
 
-	/* in case drm_panel is connected then HPD is not supported */
+	/*
+	 * HPD on this bridge chip is a bit useless.  This is an eDP bridge
+	 * so the HPD is an internal signal that's only there to signal that
+	 * the panel is done powering up.  ...but the bridge chip debounces
+	 * this signal by between 100 ms and 400 ms (depending on process,
+	 * voltage, and temperate--I measured it at about 200 ms).  One
+	 * particular panel asserted HPD 84 ms after it was powered on meaning
+	 * that we saw HPD 284 ms after power on.  ...but the same panel said
+	 * that instead of looking at HPD you could just hardcode a delay of
+	 * 200 ms.  We'll assume that the panel driver will have the hardcoded
+	 * delay in its prepare and always disable HPD.
+	 *
+	 * If HPD somehow makes sense on some future panel we'll have to
+	 * change this to be conditional on someone specifying that HPD should
+	 * be used.
+	 */
 	regmap_update_bits(pdata->regmap, SN_HPD_DISABLE_REG, HPD_DISABLE,
 			   HPD_DISABLE);
 
diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index 3c9fc99648b7..08821dfa3327 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -119,6 +119,9 @@ static const struct edid_quirk {
 	/* SDC panel of Lenovo B50-80 reports 8 bpc, but is a 6 bpc panel */
 	{ "SDC", 0x3652, EDID_QUIRK_FORCE_6BPC },
 
+	/* BOE model 0x0771 reports 8 bpc, but is a 6 bpc panel */
+	{ "BOE", 0x0771, EDID_QUIRK_FORCE_6BPC },
+
 	/* Belinea 10 15 55 */
 	{ "MAX", 1516, EDID_QUIRK_PREFER_LARGE_60 },
 	{ "MAX", 0x77e, EDID_QUIRK_PREFER_LARGE_60 },
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 97964f7f2ace..a04ffb3b2174 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -56,6 +56,8 @@ struct panel_desc {
 	/**
 	 * @prepare: the time (in milliseconds) that it takes for the panel to
 	 *           become ready and start receiving video data
+	 * @hpd_absent_delay: Add this to the prepare delay if we know Hot
+	 *                    Plug Detect isn't used.
 	 * @enable: the time (in milliseconds) that it takes for the panel to
 	 *          display the first valid frame after starting to receive
 	 *          video data
@@ -66,6 +68,7 @@ struct panel_desc {
 	 */
 	struct {
 		unsigned int prepare;
+		unsigned int hpd_absent_delay;
 		unsigned int enable;
 		unsigned int disable;
 		unsigned int unprepare;
@@ -79,6 +82,7 @@ struct panel_simple {
 	struct drm_panel base;
 	bool prepared;
 	bool enabled;
+	bool no_hpd;
 
 	const struct panel_desc *desc;
 
@@ -202,6 +206,7 @@ static int panel_simple_unprepare(struct drm_panel *panel)
 static int panel_simple_prepare(struct drm_panel *panel)
 {
 	struct panel_simple *p = to_panel_simple(panel);
+	unsigned int delay;
 	int err;
 
 	if (p->prepared)
@@ -215,8 +220,11 @@ static int panel_simple_prepare(struct drm_panel *panel)
 
 	gpiod_set_value_cansleep(p->enable_gpio, 1);
 
-	if (p->desc->delay.prepare)
-		msleep(p->desc->delay.prepare);
+	delay = p->desc->delay.prepare;
+	if (p->no_hpd)
+		delay += p->desc->delay.hpd_absent_delay;
+	if (delay)
+		msleep(delay);
 
 	p->prepared = true;
 
@@ -305,6 +313,8 @@ static int panel_simple_probe(struct device *dev, const struct panel_desc *desc)
 	panel->prepared = false;
 	panel->desc = desc;
 
+	panel->no_hpd = of_property_read_bool(dev->of_node, "no-hpd");
+
 	panel->supply = devm_regulator_get(dev, "power");
 	if (IS_ERR(panel->supply))
 		return PTR_ERR(panel->supply);
@@ -1363,7 +1373,7 @@ static const struct panel_desc innolux_n156bge_l21 = {
 	},
 };
 
-static const struct drm_display_mode innolux_tv123wam_mode = {
+static const struct drm_display_mode innolux_p120zdg_bf1_mode = {
 	.clock = 206016,
 	.hdisplay = 2160,
 	.hsync_start = 2160 + 48,
@@ -1377,15 +1387,16 @@ static const struct drm_display_mode innolux_tv123wam_mode = {
 	.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC,
 };
 
-static const struct panel_desc innolux_tv123wam = {
-	.modes = &innolux_tv123wam_mode,
+static const struct panel_desc innolux_p120zdg_bf1 = {
+	.modes = &innolux_p120zdg_bf1_mode,
 	.num_modes = 1,
 	.bpc = 8,
 	.size = {
-		.width = 259,
-		.height = 173,
+		.width = 254,
+		.height = 169,
 	},
 	.delay = {
+		.hpd_absent_delay = 200,
 		.unprepare = 500,
 	},
 };
@@ -2445,8 +2456,8 @@ static const struct of_device_id platform_of_match[] = {
 		.compatible = "innolux,n156bge-l21",
 		.data = &innolux_n156bge_l21,
 	}, {
-		.compatible = "innolux,tv123wam",
-		.data = &innolux_tv123wam,
+		.compatible = "innolux,p120zdg-bf1",
+		.data = &innolux_p120zdg_bf1,
 	}, {
 		.compatible = "innolux,zj070na-01p",
 		.data = &innolux_zj070na_01p,