Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

Pull hw lockdown support from David Howells:
 "Annotation of module parameters that configure hardware resources
  including ioports, iomem addresses, irq lines and dma channels.

  This allows a future patch to prohibit the use of such module
  parameters to prevent that hardware from being abused to gain access
  to the running kernel image as part of locking the kernel down under
  UEFI secure boot conditions.

  Annotations are made by changing:

        module_param(n, t, p)
        module_param_named(n, v, t, p)
        module_param_array(n, t, m, p)

  to:

        module_param_hw(n, t, hwtype, p)
        module_param_hw_named(n, v, t, hwtype, p)
        module_param_hw_array(n, t, hwtype, m, p)

  where the module parameter refers to a hardware setting

  hwtype specifies the type of the resource being configured. This can
  be one of:

        ioport          Module parameter configures an I/O port
        iomem           Module parameter configures an I/O mem address
        ioport_or_iomem Module parameter could be either (runtime set)
        irq             Module parameter configures an I/O port
        dma             Module parameter configures a DMA channel
        dma_addr        Module parameter configures a DMA buffer address
        other           Module parameter configures some other value

  Note that the hwtype is compile checked, but not currently stored (the
  lockdown code probably won't require it). It is, however, there for
  future use.

  A bonus is that the hwtype can also be used for grepping.

  The intention is for the kernel to ignore or reject attempts to set
  annotated module parameters if lockdown is enabled. This applies to
  options passed on the boot command line, passed to insmod/modprobe or
  direct twiddling in /sys/module/ parameter files.

  The module initialisation then needs to handle the parameter not being
  set, by (1) giving an error, (2) probing for a value or (3) using a
  reasonable default.

  What I can't do is just reject a module out of hand because it may
  take a hardware setting in the module parameters. Some important
  modules, some ipmi stuff for instance, both probe for hardware and
  allow hardware to be manually specified; if the driver is aborts with
  any error, you don't get any ipmi hardware.

  Further, trying to do this entirely in the module initialisation code
  doesn't protect against sysfs twiddling.

  [!] Note that in and of itself, this series of patches should have no
      effect on the the size of the kernel or code execution - that is
      left to a patch in the next series to effect. It does mark
      annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
      an already existing field"

* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
  Annotate hardware config module parameters in sound/pci/
  Annotate hardware config module parameters in sound/oss/
  Annotate hardware config module parameters in sound/isa/
  Annotate hardware config module parameters in sound/drivers/
  Annotate hardware config module parameters in fs/pstore/
  Annotate hardware config module parameters in drivers/watchdog/
  Annotate hardware config module parameters in drivers/video/
  Annotate hardware config module parameters in drivers/tty/
  Annotate hardware config module parameters in drivers/staging/vme/
  Annotate hardware config module parameters in drivers/staging/speakup/
  Annotate hardware config module parameters in drivers/staging/media/
  Annotate hardware config module parameters in drivers/scsi/
  Annotate hardware config module parameters in drivers/pcmcia/
  Annotate hardware config module parameters in drivers/pci/hotplug/
  Annotate hardware config module parameters in drivers/parport/
  Annotate hardware config module parameters in drivers/net/wireless/
  Annotate hardware config module parameters in drivers/net/wan/
  Annotate hardware config module parameters in drivers/net/irda/
  Annotate hardware config module parameters in drivers/net/hamradio/
  Annotate hardware config module parameters in drivers/net/ethernet/
  ...

1 files changed, 7 insertions, 7 deletions

diff --git a/drivers/char/ipmi/ipmi_si_intf.c b/drivers/char/ipmi/ipmi_si_intf.c
index b2b618f066e0..59ee93ea84eb 100644
--- a/drivers/char/ipmi/ipmi_si_intf.c
+++ b/drivers/char/ipmi/ipmi_si_intf.c
@@ -1375,39 +1375,39 @@ MODULE_PARM_DESC(type, "Defines the type of each interface, each"
 		 " interface separated by commas.  The types are 'kcs',"
 		 " 'smic', and 'bt'.  For example si_type=kcs,bt will set"
 		 " the first interface to kcs and the second to bt");
-module_param_array(addrs, ulong, &num_addrs, 0);
+module_param_hw_array(addrs, ulong, iomem, &num_addrs, 0);
 MODULE_PARM_DESC(addrs, "Sets the memory address of each interface, the"
 		 " addresses separated by commas.  Only use if an interface"
 		 " is in memory.  Otherwise, set it to zero or leave"
 		 " it blank.");
-module_param_array(ports, uint, &num_ports, 0);
+module_param_hw_array(ports, uint, ioport, &num_ports, 0);
 MODULE_PARM_DESC(ports, "Sets the port address of each interface, the"
 		 " addresses separated by commas.  Only use if an interface"
 		 " is a port.  Otherwise, set it to zero or leave"
 		 " it blank.");
-module_param_array(irqs, int, &num_irqs, 0);
+module_param_hw_array(irqs, int, irq, &num_irqs, 0);
 MODULE_PARM_DESC(irqs, "Sets the interrupt of each interface, the"
 		 " addresses separated by commas.  Only use if an interface"
 		 " has an interrupt.  Otherwise, set it to zero or leave"
 		 " it blank.");
-module_param_array(regspacings, int, &num_regspacings, 0);
+module_param_hw_array(regspacings, int, other, &num_regspacings, 0);
 MODULE_PARM_DESC(regspacings, "The number of bytes between the start address"
 		 " and each successive register used by the interface.  For"
 		 " instance, if the start address is 0xca2 and the spacing"
 		 " is 2, then the second address is at 0xca4.  Defaults"
 		 " to 1.");
-module_param_array(regsizes, int, &num_regsizes, 0);
+module_param_hw_array(regsizes, int, other, &num_regsizes, 0);
 MODULE_PARM_DESC(regsizes, "The size of the specific IPMI register in bytes."
 		 " This should generally be 1, 2, 4, or 8 for an 8-bit,"
 		 " 16-bit, 32-bit, or 64-bit register.  Use this if you"
 		 " the 8-bit IPMI register has to be read from a larger"
 		 " register.");
-module_param_array(regshifts, int, &num_regshifts, 0);
+module_param_hw_array(regshifts, int, other, &num_regshifts, 0);
 MODULE_PARM_DESC(regshifts, "The amount to shift the data read from the."
 		 " IPMI register, in bits.  For instance, if the data"
 		 " is read from a 32-bit word and the IPMI data is in"
 		 " bit 8-15, then the shift would be 8");
-module_param_array(slave_addrs, int, &num_slave_addrs, 0);
+module_param_hw_array(slave_addrs, int, other, &num_slave_addrs, 0);
 MODULE_PARM_DESC(slave_addrs, "Set the default IPMB slave address for"
 		 " the controller.  Normally this is 0x20, but can be"
 		 " overridden by this parm.  This is an array indexed"