Introduce EFIKA_COMMON

The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things
so it makes sense to create a common file for both devices and a specific
file for each. No functionnal change except dropping uart 1 & 2.

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 175 insertions, 0 deletions

diff --git a/arch/arm/mach-mx5/mx51_efika.c b/arch/arm/mach-mx5/mx51_efika.c
new file mode 100644
index 000000000000..a249ca3c4138
--- /dev/null
+++ b/arch/arm/mach-mx5/mx51_efika.c
@@ -0,0 +1,175 @@
+/*
+ * based on code from the following
+ * Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2009-2010 Pegatron Corporation. All Rights Reserved.
+ * Copyright 2009-2010 Genesi USA, Inc. All Rights Reserved.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/fsl_devices.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/spi.h>
+
+#include <mach/common.h>
+#include <mach/hardware.h>
+#include <mach/iomux-mx51.h>
+#include <mach/i2c.h>
+#include <mach/mxc_ehci.h>
+
+#include <asm/irq.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include "devices-imx51.h"
+#include "devices.h"
+#include "efika.h"
+
+#define	MX51_USB_PLL_DIV_24_MHZ	0x01
+
+#define EFIKAMX_SPI_CS0		IMX_GPIO_NR(4, 24)
+#define EFIKAMX_SPI_CS1		IMX_GPIO_NR(4, 25)
+
+static iomux_v3_cfg_t mx51efika_pads[] = {
+	/* UART1 */
+	MX51_PAD_UART1_RXD__UART1_RXD,
+	MX51_PAD_UART1_TXD__UART1_TXD,
+	MX51_PAD_UART1_RTS__UART1_RTS,
+	MX51_PAD_UART1_CTS__UART1_CTS,
+
+	/* SD 1 */
+	MX51_PAD_SD1_CMD__SD1_CMD,
+	MX51_PAD_SD1_CLK__SD1_CLK,
+	MX51_PAD_SD1_DATA0__SD1_DATA0,
+	MX51_PAD_SD1_DATA1__SD1_DATA1,
+	MX51_PAD_SD1_DATA2__SD1_DATA2,
+	MX51_PAD_SD1_DATA3__SD1_DATA3,
+
+	/* SD 2 */
+	MX51_PAD_SD2_CMD__SD2_CMD,
+	MX51_PAD_SD2_CLK__SD2_CLK,
+	MX51_PAD_SD2_DATA0__SD2_DATA0,
+	MX51_PAD_SD2_DATA1__SD2_DATA1,
+	MX51_PAD_SD2_DATA2__SD2_DATA2,
+	MX51_PAD_SD2_DATA3__SD2_DATA3,
+
+	/* SD/MMC WP/CD */
+	MX51_PAD_GPIO1_0__SD1_CD,
+	MX51_PAD_GPIO1_1__SD1_WP,
+	MX51_PAD_GPIO1_7__SD2_WP,
+	MX51_PAD_GPIO1_8__SD2_CD,
+
+	/* spi */
+	MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
+	MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
+	MX51_PAD_CSPI1_SS0__GPIO4_24,
+	MX51_PAD_CSPI1_SS1__GPIO4_25,
+	MX51_PAD_CSPI1_RDY__ECSPI1_RDY,
+	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
+};
+
+/* Serial ports */
+static const struct imxuart_platform_data uart_pdata = {
+	.flags = IMXUART_HAVE_RTSCTS,
+};
+
+/* This function is board specific as the bit mask for the plldiv will also
+ * be different for other Freescale SoCs, thus a common bitmask is not
+ * possible and cannot get place in /plat-mxc/ehci.c.
+ */
+static int initialize_otg_port(struct platform_device *pdev)
+{
+	u32 v;
+	void __iomem *usb_base;
+	void __iomem *usbother_base;
+	usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
+	if (!usb_base)
+		return -ENOMEM;
+	usbother_base = (void __iomem *)(usb_base + MX5_USBOTHER_REGS_OFFSET);
+
+	/* Set the PHY clock to 19.2MHz */
+	v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
+	v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
+	v |= MX51_USB_PLL_DIV_24_MHZ;
+	__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
+	iounmap(usb_base);
+
+	mdelay(10);
+
+	return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
+}
+
+static struct mxc_usbh_platform_data dr_utmi_config = {
+	.init   = initialize_otg_port,
+	.portsc = MXC_EHCI_UTMI_16BIT,
+};
+
+static struct mtd_partition mx51_efika_spi_nor_partitions[] = {
+	{
+	 .name = "u-boot",
+	 .offset = 0,
+	 .size = SZ_256K,
+	},
+	{
+	  .name = "config",
+	  .offset = MTDPART_OFS_APPEND,
+	  .size = SZ_64K,
+	},
+};
+
+static struct flash_platform_data mx51_efika_spi_flash_data = {
+	.name		= "spi_flash",
+	.parts		= mx51_efika_spi_nor_partitions,
+	.nr_parts	= ARRAY_SIZE(mx51_efika_spi_nor_partitions),
+	.type		= "sst25vf032b",
+};
+
+static struct spi_board_info mx51_efika_spi_board_info[] __initdata = {
+	{
+		.modalias = "m25p80",
+		.max_speed_hz = 25000000,
+		.bus_num = 0,
+		.chip_select = 1,
+		.platform_data = &mx51_efika_spi_flash_data,
+		.irq = -1,
+	},
+};
+
+static int mx51_efika_spi_cs[] = {
+	EFIKAMX_SPI_CS0,
+	EFIKAMX_SPI_CS1,
+};
+
+static const struct spi_imx_master mx51_efika_spi_pdata __initconst = {
+	.chipselect     = mx51_efika_spi_cs,
+	.num_chipselect = ARRAY_SIZE(mx51_efika_spi_cs),
+};
+
+void __init efika_board_common_init(void)
+{
+	mxc_iomux_v3_setup_multiple_pads(mx51efika_pads,
+					ARRAY_SIZE(mx51efika_pads));
+	mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
+	imx51_add_imx_uart(0, &uart_pdata);
+	imx51_add_sdhci_esdhc_imx(0, NULL);
+
+	spi_register_board_info(mx51_efika_spi_board_info,
+		ARRAY_SIZE(mx51_efika_spi_board_info));
+	imx51_add_ecspi(0, &mx51_efika_spi_pdata);
+}
+