Merge tag 'hwmon-for-linus-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - New drivers for FTS BMC "Teutates", TI INA3221, and Sensirion SHT3x.

 - Added support for Microchip MCP9808 and TI TMP461.

 - Cleanup and minor fixes in various drivers.

* tag 'hwmon-for-linus-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (37 commits)
  Documentation: dtb: xgene: Add hwmon dts binding documentation
  hwmon: (ftsteutates) Remove unused including <linux/version.h>
  hwmon: (adt7411) set bit 3 in CFG1 register
  hwmon: Add driver for FTS BMC chip "Teutates"
  hwmon: (sht3x) add humidity heater element control
  hwmon: (jc42) Add support for generic JC-42.4 devicetree binding
  dt/bindings: Add bindings for JC-42.4 compatible temperature sensors
  hwmon: (tmp102) Convert to use regmap, and drop local cache
  hwmon: (tmp102) Rework chip configuration
  hwmon: (tmp102) Improve handling of initial read delay
  hwmon: (lm90) Drop unnecessary else statements
  hwmon: (lm90) Use bool for valid flag
  hwmon: (lm90) Read limit registers only once
  hwmon: (lm90) Simplify read functions
  hwmon: (lm90) Use devm_hwmon_device_register_with_groups
  hwmon: (lm90) Use devm_add_action for cleanup
  hwmon: (lm75) Convert to use regmap
  hwmon: (lm75) Add update_interval attribute
  hwmon: (lm75) Drop lm75_read_value and lm75_write_value
  hwmon: (lm75) Handle cleanup with devm_add_action
  ...

10 files changed, 240 insertions, 11 deletions

diff --git a/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt b/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt
new file mode 100644
index 000000000000..59b38557f1bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt
@@ -0,0 +1,14 @@
+APM X-Gene hwmon driver
+
+APM X-Gene SOC sensors are accessed over the "SLIMpro" mailbox.
+
+Required properties :
+ - compatible : should be "apm,xgene-slimpro-hwmon"
+ - mboxes : use the label reference for the mailbox as the first parameter.
+	    The second parameter is the channel number.
+
+Example :
+	hwmonslimpro {
+		compatible = "apm,xgene-slimpro-hwmon";
+		mboxes = <&mailbox 7>;
+	};
diff --git a/Documentation/devicetree/bindings/hwmon/jc42.txt b/Documentation/devicetree/bindings/hwmon/jc42.txt
new file mode 100644
index 000000000000..07a250498fbb
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/jc42.txt
@@ -0,0 +1,42 @@
+Properties for Jedec JC-42.4 compatible temperature sensors
+
+Required properties:
+- compatible: May include a device-specific string consisting of the
+	      manufacturer and the name of the chip. A list of supported
+	      chip names follows.
+	      Must include "jedec,jc-42.4-temp" for any Jedec JC-42.4
+	      compatible temperature sensor.
+
+	      Supported chip names:
+		adi,adt7408
+		atmel,at30ts00
+		atmel,at30tse004
+		onnn,cat6095
+		onnn,cat34ts02
+		maxim,max6604
+		microchip,mcp9804
+		microchip,mcp9805
+		microchip,mcp9808
+		microchip,mcp98243
+		microchip,mcp98244
+		microchip,mcp9843
+		nxp,se97
+		nxp,se98
+		st,stts2002
+		st,stts2004
+		st,stts3000
+		st,stts424
+		st,stts424e
+		idt,tse2002
+		idt,tse2004
+		idt,ts3000
+		idt,ts3001
+
+- reg: I2C address
+
+Example:
+
+temp-sensor@1a {
+	compatible = "jedec,jc-42.4-temp";
+	reg = <0x1a>;
+};
diff --git a/Documentation/hwmon/abituguru b/Documentation/hwmon/abituguru
index f1d4fe4c366c..44013d23b3f0 100644
--- a/Documentation/hwmon/abituguru
+++ b/Documentation/hwmon/abituguru
@@ -24,7 +24,7 @@ Supported chips:
 				 AW9D-MAX) (2)
 	1) For revisions 2 and 3 uGuru's the driver can autodetect the
 	   sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's
-	   this doesnot always work. For these uGuru's the autodection can
+	   this does not always work. For these uGuru's the autodetection can
 	   be overridden with the bank1_types module param. For all 3 known
 	   revison 1 motherboards the correct use of this param is:
 	   bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1
diff --git a/Documentation/hwmon/ftsteutates b/Documentation/hwmon/ftsteutates
new file mode 100644
index 000000000000..2a1bf69c6a26
--- /dev/null
+++ b/Documentation/hwmon/ftsteutates
@@ -0,0 +1,23 @@
+Kernel driver ftsteutates
+=====================
+
+Supported chips:
+  * FTS Teutates
+    Prefix: 'ftsteutates'
+    Addresses scanned: I2C 0x73 (7-Bit)
+
+Author: Thilo Cestonaro <thilo.cestonaro@ts.fujitsu.com>
+
+
+Description
+-----------
+The BMC Teutates is the Eleventh generation of Superior System
+monitoring and thermal management solution. It is builds on the basic
+functionality of the BMC Theseus and contains several new features and
+enhancements. It can monitor up to 4 voltages, 16 temperatures and
+8 fans. It also contains an integrated watchdog which is currently
+implemented in this driver.
+
+Specification of the chip can be found here:
+ftp:///pub/Mainboard-OEM-Sales/Services/Software&Tools/Linux_SystemMonitoring&Watchdog&GPIO/BMC-Teutates_Specification_V1.21.pdf
+ftp:///pub/Mainboard-OEM-Sales/Services/Software&Tools/Linux_SystemMonitoring&Watchdog&GPIO/Fujitsu_mainboards-1-Sensors_HowTo-en-US.pdf
diff --git a/Documentation/hwmon/ina3221 b/Documentation/hwmon/ina3221
new file mode 100644
index 000000000000..0ff74854cb2e
--- /dev/null
+++ b/Documentation/hwmon/ina3221
@@ -0,0 +1,35 @@
+Kernel driver ina3221
+=====================
+
+Supported chips:
+  * Texas Instruments INA3221
+    Prefix: 'ina3221'
+    Addresses: I2C 0x40 - 0x43
+    Datasheet: Publicly available at the Texas Instruments website
+               http://www.ti.com/
+
+Author: Andrew F. Davis <afd@ti.com>
+
+Description
+-----------
+
+The Texas Instruments INA3221 monitors voltage, current, and power on the high
+side of up to three D.C. power supplies. The INA3221 monitors both shunt drop
+and supply voltage, with programmable conversion times and averaging, current
+and power are calculated host-side from these.
+
+Sysfs entries
+-------------
+
+in[123]_input           Bus voltage(mV) channels
+curr[123]_input         Current(mA) measurement channels
+shunt[123]_resistor     Shunt resistance(uOhm) channels
+curr[123]_crit          Critical alert current(mA) setting, activates the
+                          corresponding alarm when the respective current
+                          is above this value
+curr[123]_crit_alarm    Critical alert current limit exceeded
+curr[123]_max           Warning alert current(mA) setting, activates the
+                          corresponding alarm when the respective current
+                          average is above this value.
+curr[123]_max_alarm     Warning alert current limit exceeded
+in[456]_input           Shunt voltage(uV) for channels 1, 2, and 3 respectively
diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42
index f7f1830a2566..b4b671f22453 100644
--- a/Documentation/hwmon/jc42
+++ b/Documentation/hwmon/jc42
@@ -18,10 +18,11 @@ Supported chips:
   * Maxim MAX6604
     Datasheets:
 	http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
-  * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP98244, MCP9843
+  * Microchip MCP9804, MCP9805, MCP9808, MCP98242, MCP98243, MCP98244, MCP9843
     Datasheets:
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
+	http://ww1.microchip.com/downloads/en/DeviceDoc/25095A.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22327A.pdf
diff --git a/Documentation/hwmon/max1668 b/Documentation/hwmon/max1668
index 0616ed9758df..8f9d570dbfec 100644
--- a/Documentation/hwmon/max1668
+++ b/Documentation/hwmon/max1668
@@ -17,7 +17,7 @@ This driver implements support for the Maxim MAX1668, MAX1805 and MAX1989
 chips.
 
 The three devices are very similar, but the MAX1805 has a reduced feature
-set; only two remote temperature inputs vs the four avaible on the other
+set; only two remote temperature inputs vs the four available on the other
 two ICs.
 
 The driver is able to distinguish between the devices and creates sysfs
diff --git a/Documentation/hwmon/sht3x b/Documentation/hwmon/sht3x
new file mode 100644
index 000000000000..b0d88184f48e
--- /dev/null
+++ b/Documentation/hwmon/sht3x
@@ -0,0 +1,76 @@
+Kernel driver sht3x
+===================
+
+Supported chips:
+  * Sensirion SHT3x-DIS
+    Prefix: 'sht3x'
+    Addresses scanned: none
+    Datasheet: http://www.sensirion.com/fileadmin/user_upload/customers/sensirion/Dokumente/Humidity/Sensirion_Humidity_Datasheet_SHT3x_DIS.pdf
+
+Author:
+  David Frey <david.frey@sensirion.com>
+  Pascal Sachs <pascal.sachs@sensirion.com>
+
+Description
+-----------
+
+This driver implements support for the Sensirion SHT3x-DIS chip, a humidity
+and temperature sensor. Temperature is measured in degrees celsius, relative
+humidity is expressed as a percentage. In the sysfs interface, all values are
+scaled by 1000, i.e. the value for 31.5 degrees celsius is 31500.
+
+The device communicates with the I2C protocol. Sensors can have the I2C
+addresses 0x44 or 0x45, depending on the wiring. See
+Documentation/i2c/instantiating-devices for methods to instantiate the device.
+
+There are two options configurable by means of sht3x_platform_data:
+1. blocking (pull the I2C clock line down while performing the measurement) or
+   non-blocking mode. Blocking mode will guarantee the fastest result but
+   the I2C bus will be busy during that time. By default, non-blocking mode
+   is used. Make sure clock-stretching works properly on your device if you
+   want to use blocking mode.
+2. high or low accuracy. High accuracy is used by default and using it is
+   strongly recommended.
+
+The sht3x sensor supports a single shot mode as well as 5 periodic measure
+modes, which can be controlled with the update_interval sysfs interface.
+The allowed update_interval in milliseconds are as follows:
+  *     0   single shot mode
+  *  2000   0.5 Hz periodic measurement
+  *  1000   1   Hz periodic measurement
+  *   500   2   Hz periodic measurement
+  *   250   4   Hz periodic measurement
+  *   100  10   Hz periodic measurement
+
+In the periodic measure mode, the sensor automatically triggers a measurement
+with the configured update interval on the chip. When a temperature or humidity
+reading exceeds the configured limits, the alert attribute is set to 1 and
+the alert pin on the sensor is set to high.
+When the temperature and humidity readings move back between the hysteresis
+values, the alert bit is set to 0 and the alert pin on the sensor is set to
+low.
+
+sysfs-Interface
+---------------
+
+temp1_input:        temperature input
+humidity1_input:    humidity input
+temp1_max:          temperature max value
+temp1_max_hyst:     temperature hysteresis value for max limit
+humidity1_max:      humidity max value
+humidity1_max_hyst: humidity hysteresis value for max limit
+temp1_min:          temperature min value
+temp1_min_hyst:     temperature hysteresis value for min limit
+humidity1_min:      humidity min value
+humidity1_min_hyst: humidity hysteresis value for min limit
+temp1_alarm:        alarm flag is set to 1 if the temperature is outside the
+                    configured limits. Alarm only works in periodic measure mode
+humidity1_alarm:    alarm flag is set to 1 if the humidity is outside the
+                    configured limits. Alarm only works in periodic measure mode
+heater_enable:      heater enable, heating element removes excess humidity from
+                    sensor
+                        0: turned off
+                        1: turned on
+update_interval:    update interval, 0 for single shot, interval in msec
+                    for periodic measurement. If the interval is not supported
+                    by the sensor, the next faster interval is chosen
diff --git a/Documentation/hwmon/submitting-patches b/Documentation/hwmon/submitting-patches
index d201828d202f..57f60307accc 100644
--- a/Documentation/hwmon/submitting-patches
+++ b/Documentation/hwmon/submitting-patches
@@ -15,10 +15,15 @@ increase the chances of your change being accepted.
     Documentation/SubmittingPatches
     Documentation/CodingStyle
 
-* If your patch generates checkpatch warnings, please refrain from explanations
-  such as "I don't like that coding style". Keep in mind that each unnecessary
-  warning helps hiding a real problem. If you don't like the kernel coding
-  style, don't write kernel drivers.
+* Please run your patch through 'checkpatch --strict'. There should be no
+  errors, no warnings, and few if any check messages. If there are any
+  messages, please be prepared to explain.
+
+* If your patch generates checkpatch errors, warnings, or check messages,
+  please refrain from explanations such as "I prefer that coding style".
+  Keep in mind that each unnecessary message helps hiding a real problem,
+  and a consistent coding style makes it easier for others to understand
+  and review the code.
 
 * Please test your patch thoroughly. We are not your test group.
   Sometimes a patch can not or not completely be tested because of missing
@@ -61,15 +66,30 @@ increase the chances of your change being accepted.
 
 * Make sure that all dependencies are listed in Kconfig.
 
+* Please list include files in alphabetic order.
+
+* Please align continuation lines with '(' on the previous line.
+
 * Avoid forward declarations if you can. Rearrange the code if necessary.
 
+* Avoid macros to generate groups of sensor attributes. It not only confuses
+  checkpatch, but also makes it more difficult to review the code.
+
 * Avoid calculations in macros and macro-generated functions. While such macros
   may save a line or so in the source, it obfuscates the code and makes code
   review more difficult. It may also result in code which is more complicated
   than necessary. Use inline functions or just regular functions instead.
 
+* Limit the number of kernel log messages. In general, your driver should not
+  generate an error message just because a runtime operation failed. Report
+  errors to user space instead, using an appropriate error code. Keep in mind
+  that kernel error log messages not only fill up the kernel log, but also are
+  printed synchronously, most likely with interrupt disabled, often to a serial
+  console. Excessive logging can seriously affect system performance.
+
 * Use devres functions whenever possible to allocate resources. For rationale
   and supported functions, please see Documentation/driver-model/devres.txt.
+  If a function is not supported by devres, consider using devm_add_action().
 
 * If the driver has a detect function, make sure it is silent. Debug messages
   and messages printed after a successful detection are acceptable, but it
@@ -96,8 +116,16 @@ increase the chances of your change being accepted.
   writing to it might cause a bad misconfiguration.
 
 * Make sure there are no race conditions in the probe function. Specifically,
-  completely initialize your chip first, then create sysfs entries and register
-  with the hwmon subsystem.
+  completely initialize your chip and your driver first, then register with
+  the hwmon subsystem.
+
+* Use devm_hwmon_device_register_with_groups() or, if your driver needs a remove
+  function, hwmon_device_register_with_groups() to register your driver with the
+  hwmon subsystem. Try using devm_add_action() instead of a remove function if
+  possible. Do not use hwmon_device_register().
+
+* Your driver should be buildable as module. If not, please be prepared to
+  explain why it has to be built into the kernel.
 
 * Do not provide support for deprecated sysfs attributes.
 
diff --git a/Documentation/hwmon/tmp401 b/Documentation/hwmon/tmp401
index 711f75e189eb..2d9ca42213cf 100644
--- a/Documentation/hwmon/tmp401
+++ b/Documentation/hwmon/tmp401
@@ -22,6 +22,9 @@ Supported chips:
     Prefix: 'tmp435'
     Addresses scanned: I2C 0x48 - 0x4f
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp435.html
+  * Texas Instruments TMP461
+    Prefix: 'tmp461'
+    Datasheet: http://www.ti.com/product/tmp461
 
 Authors:
          Hans de Goede <hdegoede@redhat.com>
@@ -31,8 +34,8 @@ Description
 -----------
 
 This driver implements support for Texas Instruments TMP401, TMP411,
-TMP431, TMP432 and TMP435 chips. These chips implement one or two remote
-and one local temperature sensors. Temperature is measured in degrees
+TMP431, TMP432, TMP435, and TMP461 chips. These chips implement one or two
+remote and one local temperature sensors. Temperature is measured in degrees
 Celsius. Resolution of the remote sensor is 0.0625 degree. Local
 sensor resolution can be set to 0.5, 0.25, 0.125 or 0.0625 degree (not
 supported by the driver so far, so using the default resolution of 0.5
@@ -55,3 +58,10 @@ some additional features.
 
 TMP432 is compatible with TMP401 and TMP431. It supports two external
 temperature sensors.
+
+TMP461 is compatible with TMP401. It supports offset correction
+that is applied to the remote sensor.
+
+* Sensor offset values are temperature values
+
+  Exported via sysfs attribute tempX_offset