Merge tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.8 kernel cycle.

  Nothing stands out as especially exiting: new drivers, new subdrivers,
  lots of cleanups and incremental features.

  Business as usual.

  New drivers:

   - New driver for Oxnas pin control and GPIO.  This ARM-based chipset
     is used in a few storage (NAS) type devices.

   - New driver for the MAX77620/MAX20024 pin controller portions.

   - New driver for the Intel Merrifield pin controller.

  New subdrivers:

   - New subdriver for the Qualcomm MDM9615

   - New subdriver for the STM32F746 MCU

   - New subdriver for the Broadcom NSP SoC.

  Cleanups:

   - Demodularization of bool compiled-in drivers.

  Apart from this there is just regular incremental improvements to a
  lot of drivers, especially Uniphier and PFC"

* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
  pinctrl: fix pincontrol definition for marvell
  pinctrl: xway: fix typo
  Revert "pinctrl: amd: make it explicitly non-modular"
  pinctrl: iproc: Add NSP and Stingray GPIO support
  pinctrl: Update iProc GPIO DT bindings
  pinctrl: bcm: add OF dependencies
  pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
  pinctrl: Add STM32F746 MCU support
  pinctrl: intel: Protect set wake flow by spin lock
  pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
  pinctrl: uniphier: add Ethernet pin-mux settings
  sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
  pinctrl: ns2: fix return value check in ns2_pinmux_probe()
  pinctrl: qcom: update DT bindings with ebi2 groups
  pinctrl: qcom: establish proper EBI2 pin groups
  pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
  Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
  includes: dt-bindings: Add STM32F746 pinctrl DT bindings
  pinctrl: sunxi: fix nand0 function name for sun8i
  pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
  ...

12 files changed, 498 insertions, 17 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
new file mode 100644
index 000000000000..928ed4f43907
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
@@ -0,0 +1,47 @@
+* Oxford Semiconductor OXNAS SoC GPIO Controller
+
+Please refer to gpio.txt for generic information regarding GPIO bindings.
+
+Required properties:
+ - compatible: "oxsemi,ox810se-gpio"
+ - reg: Base address and length for the device.
+ - interrupts: The port interrupt shared by all pins.
+ - gpio-controller: Marks the port as GPIO controller.
+ - #gpio-cells: Two. The first cell is the pin number and
+   the second cell is used to specify the gpio polarity as defined in
+   defined in <dt-bindings/gpio/gpio.h>:
+      0 = GPIO_ACTIVE_HIGH
+      1 = GPIO_ACTIVE_LOW
+ - interrupt-controller: Marks the device node as an interrupt controller.
+ - #interrupt-cells: Two. The first cell is the GPIO number and second cell
+   is used to specify the trigger type as defined in
+   <dt-bindings/interrupt-controller/irq.h>:
+      IRQ_TYPE_EDGE_RISING
+      IRQ_TYPE_EDGE_FALLING
+      IRQ_TYPE_EDGE_BOTH
+ - gpio-ranges: Interaction with the PINCTRL subsystem, it also specifies the
+   gpio base and count, should be in the format of numeric-gpio-range as
+   specified in the gpio.txt file.
+
+Example:
+
+gpio0: gpio@0 {
+	compatible = "oxsemi,ox810se-gpio";
+	reg = <0x000000 0x100000>;
+	interrupts = <21>;
+	#gpio-cells = <2>;
+	gpio-controller;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	gpio-ranges = <&pinctrl 0 0 32>;
+};
+
+keys {
+	...
+
+	button-esc {
+		label = "ESC";
+		linux,code = <1>;
+		gpios = <&gpio0 12 0>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt
index e4277921f3e3..a73cbeb0f309 100644
--- a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt
@@ -3,8 +3,22 @@ Broadcom iProc GPIO/PINCONF Controller
 Required properties:
 
 - compatible:
-    Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio",
-    "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio"
+    "brcm,iproc-gpio" for the generic iProc based GPIO controller IP that
+    supports full-featured pinctrl and GPIO functions used in various iProc
+    based SoCs
+
+    May contain an SoC-specific compatibility string to accommodate any
+    SoC-specific features
+
+    "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or
+    "brcm,cygnus-crmu-gpio" for Cygnus SoCs
+
+    "brcm,iproc-nsp-gpio" for the iProc NSP SoC that has drive strength support
+    disabled
+
+    "brcm,iproc-stingray-gpio" for the iProc Stingray SoC that has the general
+    pinctrl support completely disabled in this IP block. In Stingray, a
+    different IP block is used to handle pinctrl related functions
 
 - reg:
     Define the base and range of the I/O address space that contains SoC
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt
new file mode 100644
index 000000000000..603564e5fe6f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt
@@ -0,0 +1,79 @@
+Broadcom NSP (Northstar plus) IOMUX Controller
+
+The NSP IOMUX controller supports group based mux configuration. In
+addition, certain pins can be muxed to GPIO function individually.
+
+Required properties:
+- compatible:
+    Must be "brcm,nsp-pinmux"
+
+- reg:
+    Should contain the register physical address and length for each of
+    GPIO_CONTROL0, GP_AUX_SEL and IPROC_CONFIG IOMUX registers
+
+Properties in subnodes:
+- function:
+    The mux function to select
+
+- groups:
+    The list of groups to select with a given function
+
+For more details, refer to
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+For example:
+
+	pinmux: pinmux@1803f1c0 {
+		compatible = "brcm,nsp-pinmux";
+		reg = <0x1803f1c0 0x04>,
+		      <0x18030028 0x04>,
+		      <0x1803f408 0x04>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm &gpio_b &nand_sel>;
+
+		pwm: pwm {
+			function = "pwm";
+			groups = "pwm0_grp", "pwm1_grp";
+		};
+
+		gpio_b: gpio_b {
+			function = "gpio_b";
+			groups = "gpio_b_0_grp", "gpio_b_1_grp";
+		};
+
+		nand_sel: nand_sel {
+			function = "nand";
+			groups = "nand_grp";
+		};
+	};
+
+List of supported functions and groups in Northstar Plus:
+
+"spi": "spi_grp"
+
+"i2c": "i2c_grp"
+
+"mdio": "mdio_grp"
+
+"pwm": "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp"
+
+"gpio_b": "gpio_b_0_grp", "gpio_b_1_grp", "gpio_b_2_grp", "gpio_b_3_grp"
+
+"uart1": "uart1_grp"
+
+"uart2": "uart2_grp"
+
+"synce": "synce_grp"
+
+"sata_led_grps": "sata0_led_grp", "sata1_led_grp"
+
+"xtal_out": "xtal_out_grp"
+
+"sdio": "sdio_pwr_grp", "sdio_1p8v_grp"
+
+"switch_led": "switch_p05_led0_grp", "switch_p05_led1_grp"
+
+"nand": "nand_grp"
+
+"emmc": "emmc_grp"
diff --git a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt
new file mode 100644
index 000000000000..d6074321f730
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt
@@ -0,0 +1,57 @@
+* Oxford Semiconductor OXNAS SoC Family Pin Controller
+
+Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and
+../interrupt-controller/interrupts.txt for generic information regarding
+pin controller, GPIO, and interrupt bindings.
+
+OXNAS 'pin configuration node' is a node of a group of pins which can be
+used for a specific device or function. This node represents configurations of
+pins, optional function, and optional mux related configuration.
+
+Required properties for pin controller node:
+ - compatible: "oxsemi,ox810se-pinctrl"
+ - oxsemi,sys-ctrl: a phandle to the system controller syscon node
+
+Required properties for pin configuration sub-nodes:
+ - pins: List of pins to which the configuration applies.
+
+Optional properties for pin configuration sub-nodes:
+----------------------------------------------------
+ - function: Mux function for the specified pins.
+ - bias-pull-up: Enable weak pull-up.
+
+Example:
+
+pinctrl: pinctrl {
+	compatible = "oxsemi,ox810se-pinctrl";
+
+	/* Regmap for sys registers */
+	oxsemi,sys-ctrl = <&sys>;
+
+	pinctrl_uart2: pinctrl_uart2 {
+		uart2a {
+			pins = "gpio31";
+			function = "fct3";
+		};
+		uart2b {
+			pins = "gpio32";
+			function = "fct3";
+		};
+	};
+};
+
+uart2: serial@900000 {
+	compatible = "ns16550a";
+	reg = <0x900000 0x100000>;
+	clocks = <&sysclk>;
+	interrupts = <29>;
+	reg-shift = <0>;
+	fifo-size = <16>;
+	reg-io-width = <1>;
+	current-speed = <115200>;
+	no-loopback-test;
+	status = "disabled";
+	resets = <&reset 22>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
new file mode 100644
index 000000000000..ad4fce3552bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
@@ -0,0 +1,127 @@
+Pincontrol driver for MAX77620 Power management IC from Maxim Semiconductor.
+
+Device has 8 GPIO pins which can be configured as GPIO as well as the
+special IO functions.
+
+Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt>
+for details of the common pinctrl bindings used by client devices,
+including the meaning of the phrase "pin configuration node".
+
+Optional Pinmux properties:
+--------------------------
+Following properties are required if default setting of pins are required
+at boot.
+- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>.
+- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
+		<pinctrl-binding.txt>.
+
+The pin configurations are defined as child of the pinctrl states node. Each
+sub-node have following properties:
+
+Required properties:
+------------------
+- pins: List of pins. Valid values of pins properties are:
+		      gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7.
+
+Optional properties:
+-------------------
+Following are optional properties defined as pinmux DT binding document
+<pinctrl-bindings.txt>. Absence of properties will leave the configuration
+on default.
+	function,
+	drive-push-pull,
+	drive-open-drain,
+	bias-pull-up,
+	bias-pull-down.
+
+Valid values for function properties are:
+	gpio, lpm-control-in, fps-out, 32k-out, sd0-dvs-in, sd1-dvs-in,
+	reference-out
+
+Theres is also customised properties for the GPIO1, GPIO2 and GPIO3. These
+customised properties are required to configure FPS configuration parameters
+of these GPIOs. Please refer <devicetree/bindings/mfd/max77620.txt> for more
+detail of Flexible Power Sequence (FPS).
+
+- maxim,active-fps-source:		FPS source for the GPIOs to get
+					enabled/disabled when system is in
+					active state.  Valid values are:
+					- MAX77620_FPS_SRC_0,
+						FPS source is FPS0.
+					- MAX77620_FPS_SRC_1,
+						FPS source is FPS1
+					- MAX77620_FPS_SRC_2 and
+						FPS source is FPS2
+					- MAX77620_FPS_SRC_NONE.
+						GPIO is not controlled
+						by FPS events and it gets
+						enabled/disabled by register
+						access.
+					Absence of this property will leave
+					the FPS configuration register for that
+					GPIO to default configuration.
+
+- maxim,active-fps-power-up-slot:	Sequencing event slot number on which
+					the GPIO get enabled when
+					master FPS input event set to HIGH.
+					Valid values are 0 to 7.
+					This is applicable if FPS source is
+					selected as FPS0, FPS1 or FPS2.
+
+- maxim,active-fps-power-down-slot:	Sequencing event slot number on which
+					the GPIO get disabled when master
+					FPS input event set to LOW.
+					Valid values are 0 to 7.
+					This is applicable if FPS source is
+					selected as FPS0, FPS1 or FPS2.
+
+- maxim,suspend-fps-source:		This is same as property
+					"maxim,active-fps-source" but value
+					get configured when system enters in
+					to suspend state.
+
+- maxim,suspend-fps-power-up-slot:	This is same as property
+					"maxim,active-fps-power-up-slot" but
+					this value get configured into FPS
+					configuration register when system
+					enters into suspend.
+					This is applicable if suspend state
+					FPS source is selected as FPS0, FPS1 or
+
+- maxim,suspend-fps-power-down-slot:	This is same as property
+					"maxim,active-fps-power-down-slot" but
+					this value get configured into FPS
+					configuration register when system
+					enters into suspend.
+					This is applicable if suspend state
+					FPS source is selected as FPS0, FPS1 or
+					FPS2.
+
+Example:
+--------
+#include <dt-bindings/mfd/max77620.h>
+...
+max77620@3c {
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&spmic_default>;
+
+	spmic_default: pinmux@0 {
+		pin_gpio0 {
+			pins = "gpio0";
+			function = "gpio";
+		};
+
+		pin_gpio1 {
+			pins = "gpio1";
+			function = "fps-out";
+			maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+		};
+
+		pin_gpio2 {
+			pins = "gpio2";
+			function = "fps-out";
+			maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt
new file mode 100644
index 000000000000..1b52f01ddcb7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt
@@ -0,0 +1,152 @@
+Qualcomm MDM9615 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MDM9615 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,mdm9615-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    gpio0-gpio87
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins.
+		    Valid values are:
+		    gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart,
+		    sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio,
+		    cdc_mclk
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	msmgpio: pinctrl@800000 {
+		compatible = "qcom,mdm9615-pinctrl";
+		reg = <0x800000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 16 0x4>;
+
+		gsbi8_uart: gsbi8-uart {
+			mux {
+				pins = "gpio34", "gpio35";
+				function = "gsbi8";
+			};
+
+			tx {
+				pins = "gpio34";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio35";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt
index 77aa11790163..df9a838ec5f9 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt
@@ -52,7 +52,7 @@ Valid values for function are:
   gsbi2_spi_cs3_n, gsbi3, gsbi3_spi_cs1_n, gsbi3_spi_cs2_n, gsbi3_spi_cs3_n,
   gsbi4, gsbi5, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10, gsbi11, gsbi12, hdmi, i2s,
   lcdc, mdp_vsync, mi2s, pcm, ps_hold, sdc1, sdc2, sdc5, tsif1, tsif2, usb_fs1,
-  usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm,
+  usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, ebi2, ebi2cs
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
index e4d6a9d20f7d..453bd7c76d6b 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
@@ -49,6 +49,9 @@ Valid values for pins are:
   sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data
     Supports bias and drive-strength
 
+  hsic_data, hsic_strobe
+    Supports only mux
+
 Valid values for function are:
   cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm,
   blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1,
@@ -70,7 +73,7 @@ Valid values for function are:
   cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc,
   hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk,
   gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s,
-  ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, gpio
+  ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl, gpio
 
   (Note that this is not yet the complete list of functions)
 
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
index d74e631e10da..b484ba1af78c 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
@@ -9,6 +9,7 @@ of PMIC's from Qualcomm.
 	Definition: Should contain one of:
 		    "qcom,pm8018-mpp",
 		    "qcom,pm8038-mpp",
+		    "qcom,pm8058-mpp",
 		    "qcom,pm8821-mpp",
 		    "qcom,pm8841-mpp",
 		    "qcom,pm8916-mpp",
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
index 74e6ec0339d6..e4cf022c992e 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
@@ -72,7 +72,7 @@ Pin Configuration Node Properties:
 
 The pin configuration parameters use the generic pinconf bindings defined in
 pinctrl-bindings.txt in this directory. The supported parameters are
-bias-disable, bias-pull-up, bias-pull-down, drive strength and power-source. For
+bias-disable, bias-pull-up, bias-pull-down, drive-strength and power-source. For
 pins that have a configurable I/O voltage, the power-source value should be the
 nominal I/O voltage in millivolts.
 
diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
index 7b4800cc251e..587bffb9cbc6 100644
--- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
@@ -9,6 +9,7 @@ Pin controller node:
 Required properies:
  - compatible: value should be one of the following:
    (a) "st,stm32f429-pinctrl"
+   (b) "st,stm32f746-pinctrl"
  - #address-cells: The value of this property must be 1
  - #size-cells	: The value of this property must be 1
  - ranges	: defines mapping between pin controller node (parent) to
diff --git a/Documentation/pinctrl.txt b/Documentation/pinctrl.txt
index 4976389e432d..0d3b9ce0a0b9 100644
--- a/Documentation/pinctrl.txt
+++ b/Documentation/pinctrl.txt
@@ -286,13 +286,13 @@ see the section named "pin control requests from drivers" and
 "drivers needing both pin control and GPIOs" below for details. But in some
 situations a cross-subsystem mapping between pins and GPIOs is needed.
 
-Since the pin controller subsystem have its pinspace local to the pin
-controller we need a mapping so that the pin control subsystem can figure out
-which pin controller handles control of a certain GPIO pin. Since a single
-pin controller may be muxing several GPIO ranges (typically SoCs that have
-one set of pins, but internally several GPIO silicon blocks, each modelled as
-a struct gpio_chip) any number of GPIO ranges can be added to a pin controller
-instance like this:
+Since the pin controller subsystem has its pinspace local to the pin controller
+we need a mapping so that the pin control subsystem can figure out which pin
+controller handles control of a certain GPIO pin. Since a single pin controller
+may be muxing several GPIO ranges (typically SoCs that have one set of pins,
+but internally several GPIO silicon blocks, each modelled as a struct
+gpio_chip) any number of GPIO ranges can be added to a pin controller instance
+like this:
 
 struct gpio_chip chip_a;
 struct gpio_chip chip_b;
@@ -493,12 +493,12 @@ Definitions:
 - The combination of a FUNCTION and a PIN GROUP determine a certain function
   for a certain set of pins. The knowledge of the functions and pin groups
   and their machine-specific particulars are kept inside the pinmux driver,
-  from the outside only the enumerators are known, and the driver core can:
+  from the outside only the enumerators are known, and the driver core can
+  request:
 
-  - Request the name of a function with a certain selector (>= 0)
+  - The name of a function with a certain selector (>= 0)
   - A list of groups associated with a certain function
-  - Request that a certain group in that list to be activated for a certain
-    function
+  - That a certain group in that list to be activated for a certain function
 
   As already described above, pin groups are in turn self-descriptive, so
   the core will retrieve the actual pin range in a certain group from the
@@ -831,7 +831,7 @@ separate memory range only intended for GPIO driving, and the register
 range dealing with pin config and pin multiplexing get placed into a
 different memory range and a separate section of the data sheet.
 
-A flag "strict" in struct pinctrl_desc is available to check and deny
+A flag "strict" in struct pinmux_ops is available to check and deny
 simultaneous access to the same pin from GPIO and pin multiplexing
 consumers on hardware of this type. The pinctrl driver should set this flag
 accordingly.