Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6

Conflicts:
	drivers/net/tokenring/tmspci.c
	drivers/net/ucc_geth_mii.c

2 files changed, 40 insertions, 6 deletions

diff --git a/Documentation/networking/ipv6.txt b/Documentation/networking/ipv6.txt
new file mode 100644
index 000000000000..268e5c103dd8
--- /dev/null
+++ b/Documentation/networking/ipv6.txt
@@ -0,0 +1,35 @@
+
+Options for the ipv6 module are supplied as parameters at load time.
+
+Module options may be given as command line arguments to the insmod
+or modprobe command, but are usually specified in either the
+/etc/modules.conf or /etc/modprobe.conf configuration file, or in a
+distro-specific configuration file.
+
+The available ipv6 module parameters are listed below.  If a parameter
+is not specified the default value is used.
+
+The parameters are as follows:
+
+disable
+
+	Specifies whether to load the IPv6 module, but disable all
+	its functionality.  This might be used when another module
+	has a dependency on the IPv6 module being loaded, but no
+	IPv6 addresses or operations are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled.
+
+		No IPv6 addresses will be added to interfaces, and
+		it will not be possible to open an IPv6 socket.
+
+		A reboot is required to enable IPv6.
+
diff --git a/Documentation/scsi/cxgb3i.txt b/Documentation/scsi/cxgb3i.txt
index 8141fa01978e..7ac8032ee9b2 100644
--- a/Documentation/scsi/cxgb3i.txt
+++ b/Documentation/scsi/cxgb3i.txt
@@ -4,7 +4,7 @@ Introduction
 ============
 
 The Chelsio T3 ASIC based Adapters (S310, S320, S302, S304, Mezz cards, etc.
-series of products) supports iSCSI acceleration and iSCSI Direct Data Placement
+series of products) support iSCSI acceleration and iSCSI Direct Data Placement
 (DDP) where the hardware handles the expensive byte touching operations, such
 as CRC computation and verification, and direct DMA to the final host memory
 destination:
@@ -31,9 +31,9 @@ destination:
 	  the TCP segments onto the wire. It handles TCP retransmission if
 	  needed.
 
-	  On receving, S3 h/w recovers the iSCSI PDU by reassembling TCP
+	  On receiving, S3 h/w recovers the iSCSI PDU by reassembling TCP
 	  segments, separating the header and data, calculating and verifying
-	  the digests, then forwards the header to the host. The payload data,
+	  the digests, then forwarding the header to the host. The payload data,
 	  if possible, will be directly placed into the pre-posted host DDP
 	  buffer. Otherwise, the payload data will be sent to the host too.
 
@@ -68,9 +68,8 @@ The following steps need to be taken to accelerates the open-iscsi initiator:
 	sure the ip address is unique in the network.
 
 3. edit /etc/iscsi/iscsid.conf
-   The default setting for MaxRecvDataSegmentLength (131072) is too big,
-   replace "node.conn[0].iscsi.MaxRecvDataSegmentLength" to be a value no
-   bigger than 15360 (for example 8192):
+   The default setting for MaxRecvDataSegmentLength (131072) is too big;
+   replace with a value no bigger than 15360 (for example 8192):
 
 	node.conn[0].iscsi.MaxRecvDataSegmentLength = 8192