Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	drivers/net/ethernet/cadence/macb.c
	drivers/net/phy/phy.c
	include/linux/skbuff.h
	net/ipv4/tcp.c
	net/switchdev/switchdev.c

Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.

phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.

tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.

macb.c involved the addition of two zyncq device entries.

skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.

Signed-off-by: David S. Miller <davem@davemloft.net>

5 files changed, 25 insertions, 9 deletions

diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt
index c40711e8e8f7..28b28309f535 100644
--- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt
+++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt
@@ -17,7 +17,8 @@ Required properties:
 - #clock-cells: from common clock binding; shall be set to 1.
 - clocks: from common clock binding; list of parent clock
   handles, shall be xtal reference clock or xtal and clkin for
-  si5351c only.
+  si5351c only. Corresponding clock input names are "xtal" and
+  "clkin" respectively.
 - #address-cells: shall be set to 1.
 - #size-cells: shall be set to 0.
 
@@ -71,6 +72,7 @@ i2c-master-node {
 
 		/* connect xtal input to 25MHz reference */
 		clocks = <&ref25>;
+		clock-names = "xtal";
 
 		/* connect xtal input as source of pll0 and pll1 */
 		silabs,pll-source = <0 0>, <1 0>;
diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
index f20b111b502a..2bee68103b01 100644
--- a/Documentation/devicetree/bindings/mtd/m25p80.txt
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
@@ -8,8 +8,8 @@ Required properties:
                is not Linux-only, but in case of Linux, see the "m25p_ids"
                table in drivers/mtd/devices/m25p80.c for the list of supported
                chips.
-               Must also include "nor-jedec" for any SPI NOR flash that can be
-               identified by the JEDEC READ ID opcode (0x9F).
+               Must also include "jedec,spi-nor" for any SPI NOR flash that can
+               be identified by the JEDEC READ ID opcode (0x9F).
 - reg : Chip-Select number
 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
 
@@ -25,7 +25,7 @@ Example:
 	flash: m25p80@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "spansion,m25p80", "nor-jedec";
+		compatible = "spansion,m25p80", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 		m25p,fast-read;
diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt
index abd67c13d344..4451ee973223 100644
--- a/Documentation/devicetree/bindings/net/cdns-emac.txt
+++ b/Documentation/devicetree/bindings/net/cdns-emac.txt
@@ -3,7 +3,8 @@
 Required properties:
 - compatible: Should be "cdns,[<chip>-]{emac}"
   Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
-  or the generic form: "cdns,emac".
+  Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
+  Or the generic form: "cdns,emac".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt
 - phy-mode: see ethernet.txt file in the same directory.
diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt
index 1e52d67d0abf..dbe6623fed1c 100644
--- a/Documentation/serial/tty.txt
+++ b/Documentation/serial/tty.txt
@@ -198,6 +198,9 @@ TTY_IO_ERROR		If set, causes all subsequent userspace read/write
 
 TTY_OTHER_CLOSED	Device is a pty and the other side has closed.
 
+TTY_OTHER_DONE		Device is a pty and the other side has closed and
+			all pending input processing has been completed.
+
 TTY_NO_WRITE_SPLIT	Prevent driver from splitting up writes into
 			smaller chunks.
 
diff --git a/Documentation/virtual/kvm/mmu.txt b/Documentation/virtual/kvm/mmu.txt
index 53838d9c6295..c59bd9bc41ef 100644
--- a/Documentation/virtual/kvm/mmu.txt
+++ b/Documentation/virtual/kvm/mmu.txt
@@ -169,6 +169,10 @@ Shadow pages contain the following information:
     Contains the value of cr4.smep && !cr0.wp for which the page is valid
     (pages for which this is true are different from other pages; see the
     treatment of cr0.wp=0 below).
+  role.smap_andnot_wp:
+    Contains the value of cr4.smap && !cr0.wp for which the page is valid
+    (pages for which this is true are different from other pages; see the
+    treatment of cr0.wp=0 below).
   gfn:
     Either the guest page table containing the translations shadowed by this
     page, or the base page frame for linear translations.  See role.direct.
@@ -344,10 +348,16 @@ on fault type:
 
 (user write faults generate a #PF)
 
-In the first case there is an additional complication if CR4.SMEP is
-enabled: since we've turned the page into a kernel page, the kernel may now
-execute it.  We handle this by also setting spte.nx.  If we get a user
-fetch or read fault, we'll change spte.u=1 and spte.nx=gpte.nx back.
+In the first case there are two additional complications:
+- if CR4.SMEP is enabled: since we've turned the page into a kernel page,
+  the kernel may now execute it.  We handle this by also setting spte.nx.
+  If we get a user fetch or read fault, we'll change spte.u=1 and
+  spte.nx=gpte.nx back.
+- if CR4.SMAP is disabled: since the page has been changed to a kernel
+  page, it can not be reused when CR4.SMAP is enabled. We set
+  CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note,
+  here we do not care the case that CR4.SMAP is enabled since KVM will
+  directly inject #PF to guest due to failed permission check.
 
 To prevent an spte that was converted into a kernel page with cr0.wp=0
 from being written by the kernel after cr0.wp has changed to 1, we make