Merge tag 'v4.13-rc4' into patchwork

Linux 4.13-rc4

* tag 'v4.13-rc4': (863 commits)
  Linux 4.13-rc4
  Fix compat_sys_sigpending breakage
  ext4: fix copy paste error in ext4_swap_extents()
  ext4: fix overflow caused by missing cast in ext4_resize_fs()
  ext4, project: expand inode extra size if possible
  ext4: cleanup ext4_expand_extra_isize_ea()
  ext4: restructure ext4_expand_extra_isize
  ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
  ext4: make xattr inode reads faster
  ext4: inplace xattr block update fails to deduplicate blocks
  ext4: remove unused mode parameter
  ext4: fix warning about stack corruption
  ext4: fix dir_nlink behaviour
  ext4: silence array overflow warning
  ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
  platform/x86: intel-vbtn: match power button on press rather than release
  ext4: release discard bio after sending discard commands
  sparc64: Fix exception handling in UltraSPARC-III memcpy.
  arm64: avoid overflow in VA_START and PAGE_OFFSET
  arm64: Fix potential race with hardware DBM in ptep_set_access_flags()
  ...

17 files changed, 48 insertions, 52 deletions

diff --git a/Documentation/admin-guide/pm/cpufreq.rst b/Documentation/admin-guide/pm/cpufreq.rst
index 463cf7e73db8..7af83a92d2d6 100644
--- a/Documentation/admin-guide/pm/cpufreq.rst
+++ b/Documentation/admin-guide/pm/cpufreq.rst
@@ -237,6 +237,14 @@ are the following:
 	This attribute is not present if the scaling driver in use does not
 	support it.
 
+``cpuinfo_cur_freq``
+	Current frequency of the CPUs belonging to this policy as obtained from
+	the hardware (in KHz).
+
+	This is expected to be the frequency the hardware actually runs at.
+	If that frequency cannot be determined, this attribute should not
+	be present.
+
 ``cpuinfo_max_freq``
 	Maximum possible operating frequency the CPUs belonging to this policy
 	can run at (in kHz).
diff --git a/Documentation/device-mapper/dm-raid.txt b/Documentation/device-mapper/dm-raid.txt
index 7e06e65586d4..4a0a7469fdd7 100644
--- a/Documentation/device-mapper/dm-raid.txt
+++ b/Documentation/device-mapper/dm-raid.txt
@@ -343,3 +343,4 @@ Version History
 1.11.0  Fix table line argument order
 	(wrong raid10_copies/raid10_format sequence)
 1.11.1  Add raid4/5/6 journal write-back support via journal_mode option
+1.12.1  fix for MD deadlock between mddev_suspend() and md_write_start() available
diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt
index 0764f9ab63dc..e20eac7a3087 100644
--- a/Documentation/devicetree/bindings/ata/sata_rcar.txt
+++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt
@@ -1,14 +1,22 @@
 * Renesas R-Car SATA
 
 Required properties:
-- compatible		: should contain one of the following:
+- compatible		: should contain one or more of the following:
 			  - "renesas,sata-r8a7779" for R-Car H1
-			    ("renesas,rcar-sata" is deprecated)
 			  - "renesas,sata-r8a7790-es1" for R-Car H2 ES1
 			  - "renesas,sata-r8a7790" for R-Car H2 other than ES1
 			  - "renesas,sata-r8a7791" for R-Car M2-W
 			  - "renesas,sata-r8a7793" for R-Car M2-N
 			  - "renesas,sata-r8a7795" for R-Car H3
+			  - "renesas,rcar-gen2-sata" for a generic R-Car Gen2 compatible device
+			  - "renesas,rcar-gen3-sata" for a generic R-Car Gen3 compatible device
+			  - "renesas,rcar-sata" is deprecated
+
+			  When compatible with the generic version nodes
+			  must list the SoC-specific version corresponding
+			  to the platform first followed by the generic
+			  version.
+
 - reg			: address and length of the SATA registers;
 - interrupts		: must consist of one interrupt specifier.
 - clocks		: must contain a reference to the functional clock.
@@ -16,7 +24,7 @@ Required properties:
 Example:
 
 sata0: sata@ee300000 {
-	compatible = "renesas,sata-r8a7791";
+	compatible = "renesas,sata-r8a7791", "renesas,rcar-gen2-sata";
 	reg = <0 0xee300000 0 0x2000>;
 	interrupt-parent = <&gic>;
 	interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt b/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt
index f69773f4252b..941bb6a6fb13 100644
--- a/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt
+++ b/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt
@@ -8,7 +8,6 @@ Required properties:
 
 Optional properties:
 - clocks: Reference to the crypto engine clock.
-- dma-mask: The address mask limitation. Defaults to 64.
 
 Example:
 
@@ -24,6 +23,5 @@ Example:
 		interrupt-names = "mem", "ring0", "ring1", "ring2", "ring3",
 				  "eip";
 		clocks = <&cpm_syscon0 1 26>;
-		dma-mask = <0xff 0xffffffff>;
 		status = "disabled";
 	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-exar.txt b/Documentation/devicetree/bindings/gpio/gpio-exar.txt
new file mode 100644
index 000000000000..4540d61824af
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-exar.txt
@@ -0,0 +1,5 @@
+Exportable MPIO interface of Exar UART chips
+
+Required properties of the device:
+ - exar,first-pin: first exportable pins (0..15)
+ - ngpios: number of exportable pins (1..16)
diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt
index d3b6e1a4713a..5aa5926029ee 100644
--- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt
+++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt
@@ -40,7 +40,7 @@ Optional properties:
 Example for a Mali-T760:
 
 gpu@ffa30000 {
-	compatible = "rockchip,rk3288-mali", "arm,mali-t760", "arm,mali-midgard";
+	compatible = "rockchip,rk3288-mali", "arm,mali-t760";
 	reg = <0xffa30000 0x10000>;
 	interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
index aad98442788b..a58c173b7ab9 100644
--- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
@@ -78,7 +78,6 @@ Example:
 	};
 
 	dwmmc0@12200000 {
-		num-slots = <1>;
 		cap-mmc-highspeed;
 		cap-sd-highspeed;
 		broken-cd;
diff --git a/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt
index 85de99fcaa2f..c54e577eea07 100644
--- a/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt
@@ -24,6 +24,5 @@ Example:
 
 		fifo-depth = <0x20>;
 		bus-width = <4>;
-		num-slots = <1>;
 		disable-wp;
 	};
diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
index 8af1afcb86dc..07242d141773 100644
--- a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
@@ -36,7 +36,6 @@ Example:
 
 	/* Board portion */
 	dwmmc0@fcd03000 {
-		num-slots = <1>;
 		vmmc-supply = <&ldo12>;
 		fifo-depth = <0x100>;
 		pinctrl-names = "default";
@@ -52,7 +51,6 @@ Example:
 
 	dwmmc_1: dwmmc1@f723e000 {
 		compatible = "hisilicon,hi6220-dw-mshc";
-		num-slots = <0x1>;
 		bus-width = <0x4>;
 		disable-wp;
 		cap-sd-highspeed;
diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
index 9cb55ca57461..ef3e5f14067a 100644
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
@@ -12,12 +12,12 @@ Required Properties:
 * #address-cells: should be 1.
 * #size-cells: should be 0.
 
-# Slots: The slot specific information are contained within child-nodes with
-  each child-node representing a supported slot. There should be atleast one
-  child node representing a card slot. The name of the child node representing
-  the slot is recommended to be slot@n where n is the unique number of the slot
-  connected to the controller. The following are optional properties which
-  can be included in the slot child node.
+# Slots (DEPRECATED): The slot specific information are contained within
+  child-nodes with each child-node representing a supported slot. There should
+  be atleast one child node representing a card slot. The name of the child node
+  representing the slot is recommended to be slot@n where n is the unique number
+  of the slot connected to the controller. The following are optional properties
+  which can be included in the slot child node.
 
 	* reg: specifies the physical slot number. The valid values of this
 	  property is 0 to (num-slots -1), where num-slots is the value
@@ -63,7 +63,7 @@ Optional properties:
   clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default.
 	  (Use the "max-frequency" instead of "clock-freq-min-max".)
 
-* num-slots: specifies the number of slots supported by the controller.
+* num-slots (DEPRECATED): specifies the number of slots supported by the controller.
   The number of physical slots actually used could be equal or less than the
   value specified by num-slots. If this property is not specified, the value
   of num-slot property is assumed to be 1.
@@ -124,7 +124,6 @@ board specific portions as listed below.
 	dwmmc0@12200000 {
 		clock-frequency = <400000000>;
 		clock-freq-min-max = <400000 200000000>;
-		num-slots = <1>;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
@@ -139,7 +138,6 @@ board specific portions as listed below.
 	dwmmc0@12200000 {
 		clock-frequency = <400000000>;
 		clock-freq-min-max = <400000 200000000>;
-		num-slots = <1>;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
index eaade0e5adeb..906819a90c2b 100644
--- a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
@@ -25,7 +25,6 @@ Example:
 		clock-frequency = <50000000>;
 		clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
 		clock-names = "biu", "ciu";
-		num-slots = <1>;
 		max-frequency = <50000000>;
 		cap-sdio-irq;
 		cap-sd-highspeed;
diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt
index 2fefa1a44afd..ad16c1f481f7 100644
--- a/Documentation/devicetree/bindings/net/brcm,amac.txt
+++ b/Documentation/devicetree/bindings/net/brcm,amac.txt
@@ -11,6 +11,7 @@ Required properties:
  - reg-names:	Names of the registers.
 		"amac_base":	Address and length of the GMAC registers
 		"idm_base":	Address and length of the GMAC IDM registers
+				(required for NSP and Northstar2)
 		"nicpm_base":	Address and length of the NIC Port Manager
 				registers (required for Northstar2)
  - interrupts:	Interrupt number
diff --git a/Documentation/devicetree/bindings/net/brcm,bgmac-nsp.txt b/Documentation/devicetree/bindings/net/brcm,bgmac-nsp.txt
deleted file mode 100644
index 022946caa7e2..000000000000
--- a/Documentation/devicetree/bindings/net/brcm,bgmac-nsp.txt
+++ /dev/null
@@ -1,24 +0,0 @@
-Broadcom GMAC Ethernet Controller Device Tree Bindings
--------------------------------------------------------------
-
-Required properties:
- - compatible:	"brcm,bgmac-nsp"
- - reg:		Address and length of the GMAC registers,
-		Address and length of the GMAC IDM registers
- - reg-names:	Names of the registers.  Must have both "gmac_base" and
-		"idm_base"
- - interrupts:	Interrupt number
-
-Optional properties:
-- mac-address:	See ethernet.txt file in the same directory
-
-Examples:
-
-gmac0: ethernet@18022000 {
-	compatible = "brcm,bgmac-nsp";
-	reg = <0x18022000 0x1000>,
-	      <0x18110000 0x1000>;
-	reg-names = "gmac_base", "idm_base";
-	interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
-	status = "disabled";
-};
diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt
index 194926f77194..1ff02afdc55a 100644
--- a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt
+++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt
@@ -4,7 +4,7 @@ Required properties:
 - compatible: Should be one of the following.
   - "rockchip,rk3066a-efuse" - for RK3066a SoCs.
   - "rockchip,rk3188-efuse" - for RK3188 SoCs.
-  - "rockchip,rk322x-efuse" - for RK322x SoCs.
+  - "rockchip,rk3228-efuse" - for RK3228 SoCs.
   - "rockchip,rk3288-efuse" - for RK3288 SoCs.
   - "rockchip,rk3399-efuse" - for RK3399 SoCs.
 - reg: Should contain the registers location and exact eFuse size
diff --git a/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt b/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt
index 07590bcdad15..7c04e22a5d6a 100644
--- a/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt
+++ b/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt
@@ -1,13 +1,20 @@
-* Broadcom Digital Timing Engine(DTE) based PTP clock driver
+* Broadcom Digital Timing Engine(DTE) based PTP clock
 
 Required properties:
-- compatible: should be "brcm,ptp-dte"
+- compatible: should contain the core compatibility string
+              and the SoC compatibility string. The SoC
+              compatibility string is to handle SoC specific
+              hardware differences.
+              Core compatibility string:
+                 "brcm,ptp-dte"
+              SoC compatibility strings:
+                 "brcm,iproc-ptp-dte" - for iproc based SoC's
 - reg: address and length of the DTE block's NCO registers
 
 Example:
 
-ptp_dte: ptp_dte@180af650 {
-	compatible = "brcm,ptp-dte";
+ptp: ptp-dte@180af650 {
+	compatible = "brcm,iproc-ptp-dte", "brcm,ptp-dte";
 	reg = <0x180af650 0x10>;
 	status = "okay";
 };
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
index e6b572409cf5..574c3a2c77d5 100644
--- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
@@ -9,7 +9,6 @@ Optional properties:
 - fsl,irda-mode : Indicate the uart supports irda mode
 - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
                   in DCE mode by default.
-- fsl,dma-size : Indicate the size of the DMA buffer and its periods
 
 Please check Documentation/devicetree/bindings/serial/serial.txt
 for the complete list of generic properties.
@@ -29,5 +28,4 @@ uart1: serial@73fbc000 {
 	interrupts = <31>;
 	uart-has-rtscts;
 	fsl,dte-mode;
-	fsl,dma-size = <1024 4>;
 };
diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt
index 0fde3dcf077a..625549d4c74a 100644
--- a/Documentation/power/runtime_pm.txt
+++ b/Documentation/power/runtime_pm.txt
@@ -435,7 +435,8 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h:
       PM status to 'suspended' and update its parent's counter of 'active'
       children as appropriate (it is only valid to use this function if
       'power.runtime_error' is set or 'power.disable_depth' is greater than
-      zero)
+      zero); it will fail and return an error code if the device has a child
+      which is active and the 'power.ignore_children' flag is unset
 
   bool pm_runtime_active(struct device *dev);
     - return true if the device's runtime PM status is 'active' or its