Merge tag 'fbdev-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux

Pull fbdev updates from Tomi Valkeinen:

 - ssd1307fb: various fixes and improvements, SSD1305 support

 - use architecture agnostic functions instead of MTRR functions in
   various fbdev drivers

 - TI DRA7xx SoC display support (arch/arm/ side)

 - OMAPDSS componentization to fix probing order issues

 - OMAPDSS scaling fixes

 - msm_fb: remove obsoleted driver

* tag 'fbdev-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (77 commits)
  msm: msm_fb: Remove dead code
  OMAPDSS: HDMI: wait for framedone when stopping video
  OMAPDSS: HDMI4: fix error handling
  OMAPDSS: DISPC: scaler debug print
  OMAPDSS: DISPC: do only y decimation on OMAP3
  OMAPDSS: DISPC: check if scaling setup failed
  OMAPDSS: DISPC: fix 64 bit issue in 5-tap
  OMAPDSS: DISPC: fix row_inc for OMAP3
  OMAPDSS: DISPC: add check for scaling limits
  OMAPDSS: DISPC: fix check_horiz_timing_omap3 args
  OMAPDSS: DISPC: fix predecimation for YUV modes
  OMAPDSS: DISPC: work-around for errata i631
  OMAPDSS: simplify submodule reg/unreg code
  OMAPDSS: componentize omapdss
  OMAPDSS: reorder uninit calls
  OMAPDSS: remove uses of __init/__exit
  OMAPDSS: fix dss_init_ports error handling
  OMAPDSS: refactor dss probe function
  OMAPDSS: move 'dss_initialized' to dss driver
  fbdev: propagate result of fb_videomode_from_videomode()
  ...

2 files changed, 23 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 7b8c1295fd90..53d87bad0adc 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -182,6 +182,7 @@ skyworks	Skyworks Solutions, Inc.
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
 solidrun	SolidRun
+solomon        Solomon Systech Limited
 sony	Sony Corporation
 spansion	Spansion Inc.
 sprd	Spreadtrum Communications Inc.
diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt
index 7a125427ff4b..d1be78db63f5 100644
--- a/Documentation/devicetree/bindings/video/ssd1307fb.txt
+++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt
@@ -2,7 +2,7 @@
 
 Required properties:
   - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for
-    now is i2c, and the supported chips are ssd1306 and ssd1307.
+    now is i2c, and the supported chips are ssd1305, ssd1306 and ssd1307.
   - reg: Should contain address of the controller on the I2C bus. Most likely
          0x3c or 0x3d
   - pwm: Should contain the pwm to use according to the OF device tree PWM
@@ -15,6 +15,16 @@ Required properties:
 
 Optional properties:
   - reset-active-low: Is the reset gpio is active on physical low?
+  - solomon,segment-no-remap: Display needs normal (non-inverted) data column
+                              to segment mapping
+  - solomon,com-seq: Display uses sequential COM pin configuration
+  - solomon,com-lrremap: Display uses left-right COM pin remap
+  - solomon,com-invdir: Display uses inverted COM pin scan direction
+  - solomon,com-offset: Number of the COM pin wired to the first display line
+  - solomon,prechargep1: Length of deselect period (phase 1) in clock cycles.
+  - solomon,prechargep2: Length of precharge period (phase 2) in clock cycles.
+                         This needs to be the higher, the higher the capacitance
+                         of the OLED's pixels is
 
 [0]: Documentation/devicetree/bindings/pwm/pwm.txt
 
@@ -26,3 +36,14 @@ ssd1307: oled@3c {
         reset-gpios = <&gpio2 7>;
         reset-active-low;
 };
+
+ssd1306: oled@3c {
+        compatible = "solomon,ssd1306fb-i2c";
+        reg = <0x3c>;
+        pwms = <&pwm 4 3000>;
+        reset-gpios = <&gpio2 7>;
+        reset-active-low;
+        solomon,com-lrremap;
+        solomon,com-invdir;
+        solomon,com-offset = <32>;
+};