Merge branch 'master' of /home/davem/src/GIT/linux-2.6/

6 files changed, 448 insertions, 1 deletions

diff --git a/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt b/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt
new file mode 100644
index 000000000000..515ebcf1b97d
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt
@@ -0,0 +1,93 @@
+PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator)
+
+Device nodes needed for operation of the ppc440spe-adma driver
+are specified hereby. These are I2O/DMA, DMA and XOR nodes
+for DMA engines and Memory Queue Module node. The latter is used
+by ADMA driver for configuration of RAID-6 H/W capabilities of
+the PPC440SPe. In addition to the nodes and properties described
+below, the ranges property of PLB node must specify ranges for
+DMA devices.
+
+ i) The I2O node
+
+ Required properties:
+
+ - compatible		: "ibm,i2o-440spe";
+ - reg			: <registers mapping>
+ - dcr-reg		: <DCR registers range>
+
+ Example:
+
+	I2O: i2o@400100000 {
+		compatible = "ibm,i2o-440spe";
+		reg = <0x00000004 0x00100000 0x100>;
+		dcr-reg = <0x060 0x020>;
+	};
+
+
+ ii) The DMA node
+
+ Required properties:
+
+ - compatible		: "ibm,dma-440spe";
+ - cell-index		: 1 cell, hardware index of the DMA engine
+			  (typically 0x0 and 0x1 for DMA0 and DMA1)
+ - reg			: <registers mapping>
+ - dcr-reg		: <DCR registers range>
+ - interrupts		: <interrupt mapping for DMA0/1 interrupts sources:
+			   2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0)
+			   and DMA Error IRQ (on UIC1). The latter is common
+			   for both DMA engines>.
+ - interrupt-parent	: needed for interrupt mapping
+
+ Example:
+
+	DMA0: dma0@400100100 {
+		compatible = "ibm,dma-440spe";
+		cell-index = <0>;
+		reg = <0x00000004 0x00100100 0x100>;
+		dcr-reg = <0x060 0x020>;
+		interrupt-parent = <&DMA0>;
+		interrupts = <0 1>;
+		#interrupt-cells = <1>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		interrupt-map = <
+			0 &UIC0 0x14 4
+			1 &UIC1 0x16 4>;
+	};
+
+
+ iii) XOR Accelerator node
+
+ Required properties:
+
+ - compatible		: "amcc,xor-accelerator";
+ - reg			: <registers mapping>
+ - interrupts		: <interrupt mapping for XOR interrupt source>
+ - interrupt-parent	: for interrupt mapping
+
+ Example:
+
+	xor-accel@400200000 {
+		compatible = "amcc,xor-accelerator";
+		reg = <0x00000004 0x00200000 0x400>;
+		interrupt-parent = <&UIC1>;
+		interrupts = <0x1f 4>;
+	};
+
+
+ iv) Memory Queue Module node
+
+ Required properties:
+
+ - compatible		: "ibm,mq-440spe";
+ - dcr-reg		: <DCR registers range>
+
+ Example:
+
+	MQ0: mq {
+		compatible = "ibm,mq-440spe";
+		dcr-reg = <0x040 0x020>;
+	};
+
diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt
index e8b5bc24d0ac..39e941515a36 100644
--- a/Documentation/powerpc/dts-bindings/fsl/board.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/board.txt
@@ -20,12 +20,16 @@ Required properities:
 - compatible : should be "fsl,fpga-pixis".
 - reg : should contain the address and the length of the FPPGA register
   set.
+- interrupt-parent: should specify phandle for the interrupt controller.
+- interrupts : should specify event (wakeup) IRQ.
 
 Example (MPC8610HPCD):
 
 	board-control@e8000000 {
 		compatible = "fsl,fpga-pixis";
 		reg = <0xe8000000 32>;
+		interrupt-parent = <&mpic>;
+		interrupts = <8 8>;
 	};
 
 * Freescale BCSR GPIO banks
diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
index cabc780f7258..5c6602dbfdc2 100644
--- a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
@@ -103,7 +103,22 @@ fsl,mpc5200-gpt nodes
 ---------------------
 On the mpc5200 and 5200b, GPT0 has a watchdog timer function.  If the board
 design supports the internal wdt, then the device node for GPT0 should
-include the empty property 'fsl,has-wdt'.
+include the empty property 'fsl,has-wdt'.  Note that this does not activate
+the watchdog.  The timer will function as a GPT if the timer api is used, and
+it will function as watchdog if the watchdog device is used.  The watchdog
+mode has priority over the gpt mode, i.e. if the watchdog is activated, any
+gpt api call to this timer will fail with -EBUSY.
+
+If you add the property
+	fsl,wdt-on-boot = <n>;
+GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it.
+If n>0, the watchdog is started with a timeout of n seconds.  If n=0, the
+configuration of the watchdog is not touched.  This is useful in two cases:
+- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later;
+- do not touch a configuration assigned by the boot loader which supervises
+  the boot process itself.
+
+The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option.
 
 An mpc5200-gpt can be used as a single line GPIO controller.  To do so,
 add the following properties to the gpt node:
diff --git a/Documentation/powerpc/dts-bindings/fsl/mpic.txt b/Documentation/powerpc/dts-bindings/fsl/mpic.txt
new file mode 100644
index 000000000000..71e39cf3215b
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/mpic.txt
@@ -0,0 +1,42 @@
+* OpenPIC and its interrupt numbers on Freescale's e500/e600 cores
+
+The OpenPIC specification does not specify which interrupt source has to
+become which interrupt number. This is up to the software implementation
+of the interrupt controller. The only requirement is that every
+interrupt source has to have an unique interrupt number / vector number.
+To accomplish this the current implementation assigns the number zero to
+the first source, the number one to the second source and so on until
+all interrupt sources have their unique number.
+Usually the assigned vector number equals the interrupt number mentioned
+in the documentation for a given core / CPU. This is however not true
+for the e500 cores (MPC85XX CPUs) where the documentation distinguishes
+between internal and external interrupt sources and starts counting at
+zero for both of them.
+
+So what to write for external interrupt source X or internal interrupt
+source Y into the device tree? Here is an example:
+
+The memory map for the interrupt controller in the MPC8544[0] shows,
+that the first interrupt source starts at 0x5_0000 (PIC Register Address
+Map-Interrupt Source Configuration Registers). This source becomes the
+number zero therefore:
+ External interrupt 0 = interrupt number 0
+ External interrupt 1 = interrupt number 1
+ External interrupt 2 = interrupt number 2
+ ...
+Every interrupt number allocates 0x20 bytes register space. So to get
+its number it is sufficient to shift the lower 16bits to right by five.
+So for the external interrupt 10 we have:
+  0x0140 >> 5 = 10
+
+After the external sources, the internal sources follow. The in core I2C
+controller on the MPC8544 for instance has the internal source number
+27. Oo obtain its interrupt number we take the lower 16bits of its memory
+address (0x5_0560) and shift it right:
+ 0x0560 >> 5 = 43
+
+Therefore the I2C device node for the MPC8544 CPU has to have the
+interrupt number 43 specified in the device tree.
+
+[0] MPC8544E PowerQUICCTM III, Integrated Host Processor Family Reference Manual
+    MPC8544ERM Rev. 1 10/2007
diff --git a/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt
new file mode 100644
index 000000000000..b558585b1aaf
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt
@@ -0,0 +1,109 @@
+
+Nintendo GameCube device tree
+=============================
+
+1) The "flipper" node
+
+  This node represents the multi-function "Flipper" chip, which packages
+  many of the devices found in the Nintendo GameCube.
+
+  Required properties:
+
+   - compatible : Should be "nintendo,flipper"
+
+1.a) The Video Interface (VI) node
+
+  Represents the interface between the graphics processor and a external
+  video encoder.
+
+  Required properties:
+
+   - compatible : should be "nintendo,flipper-vi"
+   - reg : should contain the VI registers location and length
+   - interrupts : should contain the VI interrupt
+
+1.b) The Processor Interface (PI) node
+
+  Represents the data and control interface between the main processor
+  and graphics and audio processor.
+
+  Required properties:
+
+  - compatible : should be "nintendo,flipper-pi"
+  - reg : should contain the PI registers location and length
+
+1.b.i) The "Flipper" interrupt controller node
+
+  Represents the interrupt controller within the "Flipper" chip.
+  The node for the "Flipper" interrupt controller must be placed under
+  the PI node.
+
+  Required properties:
+
+  - compatible : should be "nintendo,flipper-pic"
+
+1.c) The Digital Signal Procesor (DSP) node
+
+  Represents the digital signal processor interface, designed to offload
+  audio related tasks.
+
+  Required properties:
+
+   - compatible : should be "nintendo,flipper-dsp"
+   - reg : should contain the DSP registers location and length
+   - interrupts : should contain the DSP interrupt
+
+1.c.i) The Auxiliary RAM (ARAM) node
+
+  Represents the non cpu-addressable ram designed mainly to store audio
+  related information.
+  The ARAM node must be placed under the DSP node.
+
+  Required properties:
+
+   - compatible : should be "nintendo,flipper-aram"
+   - reg : should contain the ARAM start (zero-based) and length
+
+1.d) The Disk Interface (DI) node
+
+  Represents the interface used to communicate with mass storage devices.
+
+  Required properties:
+
+   - compatible : should be "nintendo,flipper-di"
+   - reg : should contain the DI registers location and length
+   - interrupts : should contain the DI interrupt
+
+1.e) The Audio Interface (AI) node
+
+  Represents the interface to the external 16-bit stereo digital-to-analog
+  converter.
+
+  Required properties:
+
+   - compatible : should be "nintendo,flipper-ai"
+   - reg : should contain the AI registers location and length
+   - interrupts : should contain the AI interrupt
+
+1.f) The Serial Interface (SI) node
+
+  Represents the interface to the four single bit serial interfaces.
+  The SI is a proprietary serial interface used normally to control gamepads.
+  It's NOT a RS232-type interface.
+
+  Required properties:
+
+   - compatible : should be "nintendo,flipper-si"
+   - reg : should contain the SI registers location and length
+   - interrupts : should contain the SI interrupt
+
+1.g) The External Interface (EXI) node
+
+  Represents the multi-channel SPI-like interface.
+
+  Required properties:
+
+   - compatible : should be "nintendo,flipper-exi"
+   - reg : should contain the EXI registers location and length
+   - interrupts : should contain the EXI interrupt
+
diff --git a/Documentation/powerpc/dts-bindings/nintendo/wii.txt b/Documentation/powerpc/dts-bindings/nintendo/wii.txt
new file mode 100644
index 000000000000..a7e155a023b8
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/nintendo/wii.txt
@@ -0,0 +1,184 @@
+
+Nintendo Wii device tree
+========================
+
+0) The root node
+
+  This node represents the Nintendo Wii video game console.
+
+  Required properties:
+
+   - model : Should be "nintendo,wii"
+   - compatible : Should be "nintendo,wii"
+
+1) The "hollywood" node
+
+  This node represents the multi-function "Hollywood" chip, which packages
+  many of the devices found in the Nintendo Wii.
+
+  Required properties:
+
+   - compatible : Should be "nintendo,hollywood"
+
+1.a) The Video Interface (VI) node
+
+  Represents the interface between the graphics processor and a external
+  video encoder.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-vi","nintendo,flipper-vi"
+   - reg : should contain the VI registers location and length
+   - interrupts : should contain the VI interrupt
+
+1.b) The Processor Interface (PI) node
+
+  Represents the data and control interface between the main processor
+  and graphics and audio processor.
+
+  Required properties:
+
+  - compatible : should be "nintendo,hollywood-pi","nintendo,flipper-pi"
+  - reg : should contain the PI registers location and length
+
+1.b.i) The "Flipper" interrupt controller node
+
+  Represents the "Flipper" interrupt controller within the "Hollywood" chip.
+  The node for the "Flipper" interrupt controller must be placed under
+  the PI node.
+
+  Required properties:
+
+  - #interrupt-cells : <1>
+  - compatible : should be "nintendo,flipper-pic"
+  - interrupt-controller
+
+1.c) The Digital Signal Procesor (DSP) node
+
+  Represents the digital signal processor interface, designed to offload
+  audio related tasks.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-dsp","nintendo,flipper-dsp"
+   - reg : should contain the DSP registers location and length
+   - interrupts : should contain the DSP interrupt
+
+1.d) The Serial Interface (SI) node
+
+  Represents the interface to the four single bit serial interfaces.
+  The SI is a proprietary serial interface used normally to control gamepads.
+  It's NOT a RS232-type interface.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-si","nintendo,flipper-si"
+   - reg : should contain the SI registers location and length
+   - interrupts : should contain the SI interrupt
+
+1.e) The Audio Interface (AI) node
+
+  Represents the interface to the external 16-bit stereo digital-to-analog
+  converter.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-ai","nintendo,flipper-ai"
+   - reg : should contain the AI registers location and length
+   - interrupts : should contain the AI interrupt
+
+1.f) The External Interface (EXI) node
+
+  Represents the multi-channel SPI-like interface.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-exi","nintendo,flipper-exi"
+   - reg : should contain the EXI registers location and length
+   - interrupts : should contain the EXI interrupt
+
+1.g) The Open Host Controller Interface (OHCI) nodes
+
+  Represent the USB 1.x Open Host Controller Interfaces.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-usb-ohci","usb-ohci"
+   - reg : should contain the OHCI registers location and length
+   - interrupts : should contain the OHCI interrupt
+
+1.h) The Enhanced Host Controller Interface (EHCI) node
+
+  Represents the USB 2.0 Enhanced Host Controller Interface.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-usb-ehci","usb-ehci"
+   - reg : should contain the EHCI registers location and length
+   - interrupts : should contain the EHCI interrupt
+
+1.i) The Secure Digital Host Controller Interface (SDHCI) nodes
+
+  Represent the Secure Digital Host Controller Interfaces.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-sdhci","sdhci"
+   - reg : should contain the SDHCI registers location and length
+   - interrupts : should contain the SDHCI interrupt
+
+1.j) The Inter-Processsor Communication (IPC) node
+
+  Represent the Inter-Processor Communication interface. This interface
+  enables communications between the Broadway and the Starlet processors.
+
+   - compatible : should be "nintendo,hollywood-ipc"
+   - reg : should contain the IPC registers location and length
+   - interrupts : should contain the IPC interrupt
+
+1.k) The "Hollywood" interrupt controller node
+
+  Represents the "Hollywood" interrupt controller within the
+  "Hollywood" chip.
+
+  Required properties:
+
+  - #interrupt-cells : <1>
+  - compatible : should be "nintendo,hollywood-pic"
+  - reg : should contain the controller registers location and length
+  - interrupt-controller
+  - interrupts : should contain the cascade interrupt of the "flipper" pic
+  - interrupt-parent: should contain the phandle of the "flipper" pic
+
+1.l) The General Purpose I/O (GPIO) controller node
+
+  Represents the dual access 32 GPIO controller interface.
+
+  Required properties:
+
+  - #gpio-cells : <2>
+  - compatible : should be "nintendo,hollywood-gpio"
+  - reg : should contain the IPC registers location and length
+  - gpio-controller
+
+1.m) The control node
+
+  Represents the control interface used to setup several miscellaneous
+  settings of the "Hollywood" chip like boot memory mappings, resets,
+  disk interface mode, etc.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-control"
+   - reg : should contain the control registers location and length
+
+1.n) The Disk Interface (DI) node
+
+  Represents the interface used to communicate with mass storage devices.
+
+  Required properties:
+
+   - compatible : should be "nintendo,hollywood-di"
+   - reg : should contain the DI registers location and length
+   - interrupts : should contain the DI interrupt
+