Merge branch 'synaptics-rmi4' into next

Merge updated Synaptics RMI4 support, including support for SMBus
controllers and flashing firmware.

7 files changed, 150 insertions, 4 deletions

diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
new file mode 100644
index 000000000000..bbe0e87c6188
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/atmel-isc.txt
@@ -0,0 +1,65 @@
+Atmel Image Sensor Controller (ISC)
+----------------------------------------------
+
+Required properties for ISC:
+- compatible
+	Must be "atmel,sama5d2-isc".
+- reg
+	Physical base address and length of the registers set for the device.
+- interrupts
+	Should contain IRQ line for the ISC.
+- clocks
+	List of clock specifiers, corresponding to entries in
+	the clock-names property;
+	Please refer to clock-bindings.txt.
+- clock-names
+	Required elements: "hclock", "iscck", "gck".
+- #clock-cells
+	Should be 0.
+- clock-output-names
+	Should be "isc-mck".
+- pinctrl-names, pinctrl-0
+	Please refer to pinctrl-bindings.txt.
+
+ISC supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+isc: isc@f0008000 {
+	compatible = "atmel,sama5d2-isc";
+	reg = <0xf0008000 0x4000>;
+	interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>;
+	clocks = <&isc_clk>, <&iscck>, <&isc_gclk>;
+	clock-names = "hclock", "iscck", "gck";
+	#clock-cells = <0>;
+	clock-output-names = "isc-mck";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
+
+	port {
+		isc_0: endpoint {
+			remote-endpoint = <&ov7740_0>;
+			hsync-active = <1>;
+			vsync-active = <0>;
+			pclk-sample = <1>;
+		};
+	};
+};
+
+i2c1: i2c@fc028000 {
+	ov7740: camera@21 {
+		compatible = "ovti,ov7740";
+		reg = <0x21>;
+		clocks = <&isc>;
+		clock-names = "xvclk";
+		assigned-clocks = <&isc>;
+		assigned-clock-rates = <24000000>;
+
+		port {
+			ov7740_0: endpoint {
+				remote-endpoint = <&isc_0>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt
index 55c9ad6f9599..32ced99d4244 100644
--- a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt
+++ b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt
@@ -16,9 +16,10 @@ Required properties:
 - clocks	: list of clock specifiers, corresponding to entries in
 		  clock-names property;
 - clock-names	: must contain "ppmuispx", "ppmuispx", "lite0", "lite1"
-		  "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "uart",
-		  "ispdiv0", "ispdiv1", "mcuispdiv0", "mcuispdiv1", "aclk200",
-		  "div_aclk200", "aclk400mcuisp", "div_aclk400mcuisp" entries,
+		  "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "gicisp",
+		  "pwm_isp", "mcuctl_isp", "uart", "ispdiv0", "ispdiv1",
+		  "mcuispdiv0", "mcuispdiv1", "aclk200", "div_aclk200",
+		  "aclk400mcuisp", "div_aclk400mcuisp" entries,
 		  matching entries in the clocks property.
 pmu subnode
 -----------
diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
new file mode 100644
index 000000000000..5940ca11c021
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
@@ -0,0 +1,19 @@
+* Analog Devices AD5820 autofocus coil
+
+Required Properties:
+
+  - compatible: Must contain "adi,ad5820"
+
+  - reg: I2C slave address
+
+  - VANA-supply: supply of voltage for VANA pin
+
+Example:
+
+       ad5820: coil@c {
+               compatible = "adi,ad5820";
+               reg = <0x0c>;
+
+               VANA-supply = <&vaux4>;
+       };
+
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.txt b/Documentation/devicetree/bindings/media/i2c/adv7180.txt
index 0d501154dfb2..4da486f96ff6 100644
--- a/Documentation/devicetree/bindings/media/i2c/adv7180.txt
+++ b/Documentation/devicetree/bindings/media/i2c/adv7180.txt
@@ -15,6 +15,11 @@ Required Properties :
 		"adi,adv7282"
 		"adi,adv7282-m"
 
+Optional Properties :
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+  if any.
+
+
 Example:
 
 	i2c0@1c22000 {
diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt
index 6a12960609d8..27f9b8e459ac 100644
--- a/Documentation/devicetree/bindings/media/renesas,fcp.txt
+++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt
@@ -7,12 +7,14 @@ conversion of AXI transactions in order to reduce the memory bandwidth.
 
 There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP
 for FDP (FCPF). Their configuration and behaviour depend on the module they
-are paired with. These DT bindings currently support the FCPV only.
+are paired with. These DT bindings currently support the FCPV and FCPF.
 
  - compatible: Must be one or more of the following
 
    - "renesas,r8a7795-fcpv" for R8A7795 (R-Car H3) compatible 'FCP for VSP'
+   - "renesas,r8a7795-fcpf" for R8A7795 (R-Car H3) compatible 'FCP for FDP'
    - "renesas,fcpv" for generic compatible 'FCP for VSP'
+   - "renesas,fcpf" for generic compatible 'FCP for FDP'
 
    When compatible with the generic version, nodes must list the
    SoC-specific version corresponding to the platform first, followed by the
@@ -21,6 +23,10 @@ are paired with. These DT bindings currently support the FCPV only.
  - reg: the register base and size for the device registers
  - clocks: Reference to the functional clock
 
+Optional properties:
+ - power-domains : power-domain property defined with a power domain specifier
+		   to respective power domain.
+
 
 Device node example
 -------------------
@@ -29,4 +35,5 @@ Device node example
 		compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
 		reg = <0 0xfea2f000 0 0x200>;
 		clocks = <&cpg CPG_MOD 602>;
+		power-domains = <&sysc R8A7795_PD_A3VP>;
 	};
diff --git a/Documentation/devicetree/bindings/media/st,st-hva.txt b/Documentation/devicetree/bindings/media/st,st-hva.txt
new file mode 100644
index 000000000000..0d76174a1f7e
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st,st-hva.txt
@@ -0,0 +1,24 @@
+st-hva: multi-format video encoder for STMicroelectronics SoC.
+
+Required properties:
+- compatible: should be "st,st-hva".
+- reg: HVA physical address location and length, esram address location and
+  length.
+- reg-names: names of the registers listed in registers property in the same
+  order.
+- interrupts: HVA interrupt number.
+- clocks: from common clock binding: handle hardware IP needed clocks, the
+  number of clocks may depend on the SoC type.
+  See ../clock/clock-bindings.txt for details.
+- clock-names: names of the clocks listed in clocks property in the same order.
+
+Example:
+	hva@8c85000{
+		compatible = "st,st-hva";
+		reg = <0x8c85000 0x400>, <0x6000000 0x40000>;
+		reg-names = "hva_registers", "hva_esram";
+		interrupts = <GIC_SPI 58 IRQ_TYPE_NONE>,
+			     <GIC_SPI 59 IRQ_TYPE_NONE>;
+		clock-names = "clk_hva";
+		clocks = <&clk_s_c0_flexgen CLK_HVA>;
+	};
diff --git a/Documentation/devicetree/bindings/media/stih-cec.txt b/Documentation/devicetree/bindings/media/stih-cec.txt
new file mode 100644
index 000000000000..71c4b2f4bcef
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/stih-cec.txt
@@ -0,0 +1,25 @@
+STMicroelectronics STIH4xx HDMI CEC driver
+
+Required properties:
+ - compatible : value should be "st,stih-cec"
+ - reg : Physical base address of the IP registers and length of memory
+	 mapped region.
+ - clocks : from common clock binding: handle to HDMI CEC clock
+ - interrupts : HDMI CEC interrupt number to the CPU.
+ - pinctrl-names: Contains only one value - "default"
+ - pinctrl-0: Specifies the pin control groups used for CEC hardware.
+ - resets: Reference to a reset controller
+
+Example for STIH407:
+
+sti-cec@094a087c {
+	compatible = "st,stih-cec";
+	reg = <0x94a087c 0x64>;
+	clocks = <&clk_sysin>;
+	clock-names = "cec-clk";
+	interrupts = <GIC_SPI 140 IRQ_TYPE_NONE>;
+	interrupt-names = "cec-irq";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cec0_default>;
+	resets = <&softreset STIH407_LPM_SOFTRESET>;
+};