Merge tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull MTD updates from Richard Weinberger:
 "MTD core changes:
   - Convert list_for_each to entry variant
   - Use MTD_DEVICE_ATTR_RO/RW() helper macros
   - Remove unnecessary OOM messages
   - Potential NULL dereference in mtd_otp_size()
   - Fix freeing of otp_info buffer
   - Create partname and partid debug files for child MTDs
   - tests:
      - Remove redundant assignment to err
      - Fix error return code in mtd_oobtest_init()
   - Add OTP NVMEM provider support
   - Allow specifying of_node
   - Convert sysfs sprintf/snprintf family to sysfs_emit

  Bindings changes:
   - Convert ti,am654-hbmc.txt to YAML schema
   - spi-nor: add otp property
   - Add OTP bindings
   - add YAML schema for the generic MTD bindings
   - Add brcm,trx-magic

  MTD device drivers changes:
   - Add support for microchip 48l640 EERAM
   - Remove superfluous "break"
   - sm_ftl:
      - Fix alignment of block comment
   - nftl:
      - Return -ENOMEM when kmalloc failed
   - nftlcore:
      - Remove set but rewrite variables
   - phram:
      - Fix error return code in phram_setup()
   - plat-ram:
      - Remove redundant dev_err call in platram_probe()

  MTD parsers changes:
   - Qcom:
      - Fix leaking of partition name
   - Redboot:
      - Fix style issues
      - Seek fis-index-block in the right node
   - trx:
      - Allow to use TRX parser on Mediatek SoCs
      - Allow to specify brcm, trx-magic in DT

  Raw NAND core:
   - Allow SDR timings to be nacked
   - Bring support for NV-DDR timings which involved a number of small
     preparation changes to bring new helpers, properly introduce NV-DDR
     structures, fill them, differenciate them and pick the best timing
     set.
   - Add the necessary infrastructure to parse the new gpio-cs property
     which aims at enlarging the number of available CS when a hardware
     controller is too constrained.
   - Update dead URL
   - Silence static checker warning in nand_setup_interface()
   - BBT:
      - Fix corner case in bad block table handling
   - onfi:
      - Use more recent ONFI specification wording
      - Use the BIT() macro when possible

  Raw NAND controller drivers:
   - Atmel:
      - Ensure the data interface is supported.
   - Arasan:
      - Finer grain NV-DDR configuration
      - Rename the data interface register
      - Use the right DMA mask
      - Leverage additional GPIO CS
      - Ensure proper configuration for the asserted target
      - Add support for the NV-DDR interface
      - Fix a macro parameter
   - brcmnand:
      - Convert bindings to json-schema
   - OMAP:
      - Various fixes and style improvements
      - Add larger page NAND chips support
   - PL35X:
      - New driver
   - QCOM:
      - Avoid writing to obsolete register
      - Delete an unneeded bool conversion
      - Allow override of partition parser
   - Marvell:
      - Minor documentation correction
      - Add missing clk_disable_unprepare() on error in
        marvell_nfc_resume()
   - R852:
      - Use DEVICE_ATTR_RO() helper macro
   - MTK:
      - Remove redundant dev_err call in mtk_ecc_probe()
   - HISI504:
      - Remove redundant dev_err call in probe

  SPI-NAND core:
   - Light reorganisation for the introduction of a core resume handler
   - Fix double counting of ECC stats

  SPI-NAND manufacturer drivers:
   - Macronix:
      - Add support for serial NAND flash

  SPI NOR core changes:
   - Ability to dump SFDP tables via sysfs
   - Support for erasing OTP regions on Winbond and similar flashes
   - Few API doc updates and fixes
   - Locking support for MX25L12805D

  SPI NOR controller drivers changes:
   - Use SPI_MODE_X_MASK in nxp-spifi
   - Intel Alder Lake-M SPI serial flash support"

* tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (125 commits)
  mtd: spi-nor: remove redundant continue statement
  mtd: rawnand: omap: Add larger page NAND chips support
  mtd: rawnand: omap: Various style fixes
  mtd: rawnand: omap: Check return values
  mtd: rawnand: omap: Rename a macro
  mtd: rawnand: omap: Aggregate the HW configuration of the ELM
  mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller
  dt-bindings: mtd: pl353-nand: Describe this hardware controller
  MAINTAINERS: Add PL353 NAND controller entry
  mtd: rawnand: qcom: avoid writing to obsolete register
  mtd: rawnand: marvell: Minor documentation correction
  mtd: rawnand: r852: use DEVICE_ATTR_RO() helper macro
  mtd: spinand: add SPI-NAND MTD resume handler
  mtd: spinand: Add spinand_init_flash() helper
  mtd: spinand: add spinand_read_cfg() helper
  mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()
  mtd: rawnand: arasan: Finer grain NV-DDR configuration
  mtd: rawnand: arasan: Rename the data interface register
  mtd: rawnand: onfi: Fix endianness when reading NV-DDR values
  mtd: rawnand: arasan: Use the right DMA mask
  ...

13 files changed, 658 insertions, 300 deletions

diff --git a/Documentation/devicetree/bindings/memory-controllers/arm,pl353-smc.yaml b/Documentation/devicetree/bindings/memory-controllers/arm,pl353-smc.yaml
new file mode 100644
index 000000000000..7a63c85ef8c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/arm,pl353-smc.yaml
@@ -0,0 +1,131 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/arm,pl353-smc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ARM PL353 Static Memory Controller (SMC) device-tree bindings
+
+maintainers:
+  - Miquel Raynal <miquel.raynal@bootlin.com>
+  - Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
+
+description:
+  The PL353 Static Memory Controller is a bus where you can connect two kinds
+  of memory interfaces, which are NAND and memory mapped interfaces (such as
+  SRAM or NOR).
+
+# We need a select here so we don't match all nodes with 'arm,primecell'
+select:
+  properties:
+    compatible:
+      contains:
+        const: arm,pl353-smc-r2p1
+  required:
+    - compatible
+
+properties:
+  $nodename:
+    pattern: "^memory-controller@[0-9a-f]+$"
+
+  compatible:
+    items:
+      - const: arm,pl353-smc-r2p1
+      - const: arm,primecell
+
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 1
+
+  reg:
+    items:
+      - description:
+          Configuration registers for the host and sub-controllers.
+          The three chip select regions are defined in 'ranges'.
+
+  clocks:
+    items:
+      - description: clock for the memory device bus
+      - description: main clock of the SMC
+
+  clock-names:
+    items:
+      - const: memclk
+      - const: apb_pclk
+
+  ranges:
+    minItems: 1
+    maxItems: 3
+    description: |
+      Memory bus areas for interacting with the devices. Reflects
+      the memory layout with four integer values following:
+      <cs-number> 0 <offset> <size>
+    items:
+      - description: NAND bank 0
+      - description: NOR/SRAM bank 0
+      - description: NOR/SRAM bank 1
+
+  interrupts: true
+
+patternProperties:
+  "@[0-3],[a-f0-9]+$":
+    type: object
+    description: |
+      The child device node represents the controller connected to the SMC
+      bus. The controller can be a NAND controller or a pair of any memory
+      mapped controllers such as NOR and SRAM controllers.
+
+    properties:
+      compatible:
+        description:
+          Compatible of memory controller.
+
+      reg:
+        items:
+          - items:
+              - description: |
+                  Chip-select ID, as in the parent range property.
+                minimum: 0
+                maximum: 2
+              - description: |
+                  Offset of the memory region requested by the device.
+              - description: |
+                  Length of the memory region requested by the device.
+
+    required:
+      - compatible
+      - reg
+
+required:
+  - compatible
+  - reg
+  - clock-names
+  - clocks
+  - "#address-cells"
+  - "#size-cells"
+  - ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    smcc: memory-controller@e000e000 {
+      compatible = "arm,pl353-smc-r2p1", "arm,primecell";
+      reg = <0xe000e000 0x0001000>;
+      clock-names = "memclk", "apb_pclk";
+      clocks = <&clkc 11>, <&clkc 44>;
+      ranges = <0x0 0x0 0xe1000000 0x1000000 /* Nand CS region */
+                0x1 0x0 0xe2000000 0x2000000 /* SRAM/NOR CS0 region */
+                0x2 0x0 0xe4000000 0x2000000>; /* SRAM/NOR CS1 region */
+      #address-cells = <2>;
+      #size-cells = <1>;
+
+      nfc0: nand-controller@0,0 {
+        compatible = "arm,pl353-nand-r2p1";
+        reg = <0 0 0x1000000>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/memory-controllers/pl353-smc.txt b/Documentation/devicetree/bindings/memory-controllers/pl353-smc.txt
deleted file mode 100644
index d56615fd343a..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/pl353-smc.txt
+++ /dev/null
@@ -1,47 +0,0 @@
-Device tree bindings for ARM PL353 static memory controller
-
-PL353 static memory controller supports two kinds of memory
-interfaces.i.e NAND and SRAM/NOR interfaces.
-The actual devices are instantiated from the child nodes of pl353 smc node.
-
-Required properties:
-- compatible		: Should be "arm,pl353-smc-r2p1", "arm,primecell".
-- reg			: Controller registers map and length.
-- clock-names		: List of input clock names - "memclk", "apb_pclk"
-			  (See clock bindings for details).
-- clocks		: Clock phandles (see clock bindings for details).
-- address-cells		: Must be 2.
-- size-cells		: Must be 1.
-
-Child nodes:
- For NAND the "arm,pl353-nand-r2p1" and for NOR the "cfi-flash" drivers are
-supported as child nodes.
-
-for NAND partition information please refer the below file
-Documentation/devicetree/bindings/mtd/partition.txt
-
-Example:
-	smcc: memory-controller@e000e000
-			compatible = "arm,pl353-smc-r2p1", "arm,primecell";
-			clock-names = "memclk", "apb_pclk";
-			clocks = <&clkc 11>, <&clkc 44>;
-			reg = <0xe000e000 0x1000>;
-			#address-cells = <2>;
-			#size-cells = <1>;
-			ranges = <0x0 0x0 0xe1000000 0x1000000 //Nand CS Region
-				  0x1 0x0 0xe2000000 0x2000000 //SRAM/NOR CS Region
-				  0x2 0x0 0xe4000000 0x2000000>; //SRAM/NOR CS Region
-			nand_0: flash@e1000000 {
-				compatible = "arm,pl353-nand-r2p1"
-				reg = <0 0 0x1000000>;
-				(...)
-			};
-			nor0: flash@e2000000 {
-				compatible = "cfi-flash";
-				reg = <1 0 0x2000000>;
-			};
-			nor1: flash@e4000000 {
-				compatible = "cfi-flash";
-				reg = <2 0 0x2000000>;
-			};
-	};
diff --git a/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml b/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml
new file mode 100644
index 000000000000..5f126bb9b202
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/arm,pl353-nand-r2p1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PL353 NAND Controller device tree bindings
+
+allOf:
+  - $ref: "nand-controller.yaml"
+
+maintainers:
+  - Miquel Raynal <miquel.raynal@bootlin.com>
+  - Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
+
+properties:
+  compatible:
+    items:
+      - const: arm,pl353-nand-r2p1
+
+  reg:
+    items:
+      - items:
+          - description: CS with regard to the parent ranges property
+          - description: Offset of the memory region requested by the device
+          - description: Length of the memory region requested by the device
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    smcc: memory-controller@e000e000 {
+      compatible = "arm,pl353-smc-r2p1", "arm,primecell";
+      reg = <0xe000e000 0x0001000>;
+      clock-names = "memclk", "apb_pclk";
+      clocks = <&clkc 11>, <&clkc 44>;
+      ranges = <0x0 0x0 0xe1000000 0x1000000 /* Nand CS region */
+                0x1 0x0 0xe2000000 0x2000000 /* SRAM/NOR CS0 region */
+                0x2 0x0 0xe4000000 0x2000000>; /* SRAM/NOR CS1 region */
+      #address-cells = <2>;
+      #size-cells = <1>;
+
+      nfc0: nand-controller@0,0 {
+        compatible = "arm,pl353-nand-r2p1";
+        reg = <0 0 0x1000000>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
deleted file mode 100644
index 44335a4f8bfb..000000000000
--- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
+++ /dev/null
@@ -1,186 +0,0 @@
-* Broadcom STB NAND Controller
-
-The Broadcom Set-Top Box NAND controller supports low-level access to raw NAND
-flash chips. It has a memory-mapped register interface for both control
-registers and for its data input/output buffer. On some SoCs, this controller is
-paired with a custom DMA engine (inventively named "Flash DMA") which supports
-basic PROGRAM and READ functions, among other features.
-
-This controller was originally designed for STB SoCs (BCM7xxx) but is now
-available on a variety of Broadcom SoCs, including some BCM3xxx, BCM63xx, and
-iProc/Cygnus. Its history includes several similar (but not fully register
-compatible) versions.
-
-Required properties:
-- compatible       : May contain an SoC-specific compatibility string (see below)
-                     to account for any SoC-specific hardware bits that may be
-                     added on top of the base core controller.
-                     In addition, must contain compatibility information about
-                     the core NAND controller, of the following form:
-                     "brcm,brcmnand" and an appropriate version compatibility
-                     string, like "brcm,brcmnand-v7.0"
-                     Possible values:
-                         brcm,brcmnand-v2.1
-                         brcm,brcmnand-v2.2
-                         brcm,brcmnand-v4.0
-                         brcm,brcmnand-v5.0
-                         brcm,brcmnand-v6.0
-                         brcm,brcmnand-v6.1
-                         brcm,brcmnand-v6.2
-                         brcm,brcmnand-v7.0
-                         brcm,brcmnand-v7.1
-                         brcm,brcmnand-v7.2
-                         brcm,brcmnand-v7.3
-                         brcm,brcmnand
-- reg              : the register start and length for NAND register region.
-                     (optional) Flash DMA register range (if present)
-                     (optional) NAND flash cache range (if at non-standard offset)
-- reg-names        : a list of the names corresponding to the previous register
-                     ranges. Should contain "nand" and (optionally)
-                     "flash-dma" or "flash-edu" and/or "nand-cache".
-- interrupts       : The NAND CTLRDY interrupt, (if Flash DMA is available)
-                     FLASH_DMA_DONE and if EDU is avaialble and used FLASH_EDU_DONE
-- interrupt-names  : May be "nand_ctlrdy" or "flash_dma_done" or "flash_edu_done",
-                     if broken out as individual interrupts.
-                     May be "nand", if the SoC has the individual NAND
-                     interrupts multiplexed behind another custom piece of
-                     hardware
-- #address-cells   : <1> - subnodes give the chip-select number
-- #size-cells      : <0>
-
-Optional properties:
-- clock                     : reference to the clock for the NAND controller
-- clock-names               : "nand" (required for the above clock)
-- brcm,nand-has-wp          : Some versions of this IP include a write-protect
-                              (WP) control bit. It is always available on >=
-                              v7.0. Use this property to describe the rare
-                              earlier versions of this core that include WP
-
- -- Additional SoC-specific NAND controller properties --
-
-The NAND controller is integrated differently on the variety of SoCs on which it
-is found. Part of this integration involves providing status and enable bits
-with which to control the 8 exposed NAND interrupts, as well as hardware for
-configuring the endianness of the data bus. On some SoCs, these features are
-handled via standard, modular components (e.g., their interrupts look like a
-normal IRQ chip), but on others, they are controlled in unique and interesting
-ways, sometimes with registers that lump multiple NAND-related functions
-together. The former case can be described simply by the standard interrupts
-properties in the main controller node. But for the latter exceptional cases,
-we define additional 'compatible' properties and associated register resources within the NAND controller node above.
-
- - compatible: Can be one of several SoC-specific strings. Each SoC may have
-   different requirements for its additional properties, as described below each
-   bullet point below.
-
-   * "brcm,nand-bcm63138"
-     - reg: (required) the 'NAND_INT_BASE' register range, with separate status
-       and enable registers
-     - reg-names: (required) "nand-int-base"
-
-   * "brcm,nand-bcm6368"
-     - compatible: should contain "brcm,nand-bcm<soc>", "brcm,nand-bcm6368"
-     - reg: (required) the 'NAND_INTR_BASE' register range, with combined status
-       and enable registers, and boot address registers
-     - reg-names: (required) "nand-int-base"
-
-   * "brcm,nand-iproc"
-     - reg: (required) the "IDM" register range, for interrupt enable and APB
-       bus access endianness configuration, and the "EXT" register range,
-       for interrupt status/ack.
-     - reg-names: (required) a list of the names corresponding to the previous
-       register ranges. Should contain "iproc-idm" and "iproc-ext".
-
-
-* NAND chip-select
-
-Each controller (compatible: "brcm,brcmnand") may contain one or more subnodes
-to represent enabled chip-selects which (may) contain NAND flash chips. Their
-properties are as follows.
-
-Required properties:
-- compatible                : should contain "brcm,nandcs"
-- reg                       : a single integer representing the chip-select
-                              number (e.g., 0, 1, 2, etc.)
-- #address-cells            : see partition.txt
-- #size-cells               : see partition.txt
-
-Optional properties:
-- nand-ecc-strength         : see nand-controller.yaml
-- nand-ecc-step-size        : must be 512 or 1024. See nand-controller.yaml
-- nand-on-flash-bbt         : boolean, to enable the on-flash BBT for this
-                              chip-select. See nand-controller.yaml
-- brcm,nand-oob-sector-size : integer, to denote the spare area sector size
-                              expected for the ECC layout in use. This size, in
-                              addition to the strength and step-size,
-                              determines how the hardware BCH engine will lay
-                              out the parity bytes it stores on the flash.
-                              This property can be automatically determined by
-                              the flash geometry (particularly the NAND page
-                              and OOB size) in many cases, but when booting
-                              from NAND, the boot controller has only a limited
-                              number of available options for its default ECC
-                              layout.
-
-Each nandcs device node may optionally contain sub-nodes describing the flash
-partition mapping. See partition.txt for more detail.
-
-
-Example:
-
-nand@f0442800 {
-	compatible = "brcm,brcmnand-v7.0", "brcm,brcmnand";
-	reg = <0xF0442800 0x600>,
-	      <0xF0443000 0x100>;
-	reg-names = "nand", "flash-dma";
-	interrupt-parent = <&hif_intr2_intc>;
-	interrupts = <24>, <4>;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	nandcs@1 {
-		compatible = "brcm,nandcs";
-		reg = <1>; // Chip select 1
-		nand-on-flash-bbt;
-		nand-ecc-strength = <12>;
-		nand-ecc-step-size = <512>;
-
-		// Partitions
-		#address-cells = <1>;  // <2>, for 64-bit offset
-		#size-cells = <1>;     // <2>, for 64-bit length
-		flash0.rootfs@0 {
-			reg = <0 0x10000000>;
-		};
-		flash0@0 {
-			reg = <0 0>; // MTDPART_SIZ_FULL
-		};
-		flash0.kernel@10000000 {
-			reg = <0x10000000 0x400000>;
-		};
-	};
-};
-
-nand@10000200 {
-	compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368",
-		"brcm,brcmnand-v4.0", "brcm,brcmnand";
-	reg = <0x10000200 0x180>,
-	      <0x10000600 0x200>,
-	      <0x100000b0 0x10>;
-	reg-names = "nand", "nand-cache", "nand-int-base";
-	interrupt-parent = <&periph_intc>;
-	interrupts = <50>;
-	clocks = <&periph_clk 20>;
-	clock-names = "nand";
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	nand0: nandcs@0 {
-		compatible = "brcm,nandcs";
-		reg = <0>;
-		nand-on-flash-bbt;
-		nand-ecc-strength = <1>;
-		nand-ecc-step-size = <512>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml
new file mode 100644
index 000000000000..e5f1a33332a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml
@@ -0,0 +1,242 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/brcm,brcmnand.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom STB NAND Controller
+
+maintainers:
+  - Brian Norris <computersforpeace@gmail.com>
+  - Kamal Dasu <kdasu.kdev@gmail.com>
+
+description: |
+  The Broadcom Set-Top Box NAND controller supports low-level access to raw NAND
+  flash chips. It has a memory-mapped register interface for both control
+  registers and for its data input/output buffer. On some SoCs, this controller
+  is paired with a custom DMA engine (inventively named "Flash DMA") which
+  supports basic PROGRAM and READ functions, among other features.
+
+  This controller was originally designed for STB SoCs (BCM7xxx) but is now
+  available on a variety of Broadcom SoCs, including some BCM3xxx, BCM63xx, and
+  iProc/Cygnus. Its history includes several similar (but not fully register
+  compatible) versions.
+
+  -- Additional SoC-specific NAND controller properties --
+
+  The NAND controller is integrated differently on the variety of SoCs on which
+  it is found. Part of this integration involves providing status and enable
+  bits with which to control the 8 exposed NAND interrupts, as well as hardware
+  for configuring the endianness of the data bus. On some SoCs, these features
+  are handled via standard, modular components (e.g., their interrupts look like
+  a normal IRQ chip), but on others, they are controlled in unique and
+  interesting ways, sometimes with registers that lump multiple NAND-related
+  functions together. The former case can be described simply by the standard
+  interrupts properties in the main controller node. But for the latter
+  exceptional cases, we define additional 'compatible' properties and associated
+  register resources within the NAND controller node above.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - brcm,brcmnand-v2.1
+              - brcm,brcmnand-v2.2
+              - brcm,brcmnand-v4.0
+              - brcm,brcmnand-v5.0
+              - brcm,brcmnand-v6.0
+              - brcm,brcmnand-v6.1
+              - brcm,brcmnand-v6.2
+              - brcm,brcmnand-v7.0
+              - brcm,brcmnand-v7.1
+              - brcm,brcmnand-v7.2
+              - brcm,brcmnand-v7.3
+          - const: brcm,brcmnand
+      - description: BCM63138 SoC-specific NAND controller
+        items:
+          - const: brcm,nand-bcm63138
+          - enum:
+              - brcm,brcmnand-v7.0
+              - brcm,brcmnand-v7.1
+          - const: brcm,brcmnand
+      - description: iProc SoC-specific NAND controller
+        items:
+          - const: brcm,nand-iproc
+          - const: brcm,brcmnand-v6.1
+          - const: brcm,brcmnand
+      - description: BCM63168 SoC-specific NAND controller
+        items:
+          - const: brcm,nand-bcm63168
+          - const: brcm,nand-bcm6368
+          - const: brcm,brcmnand-v4.0
+          - const: brcm,brcmnand
+
+  reg:
+    minItems: 1
+    maxItems: 6
+
+  reg-names:
+    minItems: 1
+    maxItems: 6
+    items:
+      enum: [ nand, flash-dma, flash-edu, nand-cache, nand-int-base, iproc-idm, iproc-ext ]
+
+  interrupts:
+    minItems: 1
+    maxItems: 3
+    items:
+      - description: NAND CTLRDY interrupt
+      - description: FLASH_DMA_DONE if flash DMA is available
+      - description: FLASH_EDU_DONE if EDU is available
+
+  interrupt-names:
+    minItems: 1
+    maxItems: 3
+    items:
+      - const: nand_ctlrdy
+      - const: flash_dma_done
+      - const: flash_edu_done
+
+  clocks:
+    maxItems: 1
+    description: reference to the clock for the NAND controller
+
+  clock-names:
+    const: nand
+
+  brcm,nand-has-wp:
+    description: >
+      Some versions of this IP include a write-protect
+      (WP) control bit. It is always available on >=
+      v7.0. Use this property to describe the rare
+      earlier versions of this core that include WP
+    type: boolean
+
+patternProperties:
+  "^nand@[a-f0-9]$":
+    type: object
+    properties:
+      compatible:
+        const: brcm,nandcs
+
+      nand-ecc-step-size:
+        enum: [ 512, 1024 ]
+
+      brcm,nand-oob-sector-size:
+        description: |
+          integer, to denote the spare area sector size
+          expected for the ECC layout in use. This size, in
+          addition to the strength and step-size,
+          determines how the hardware BCH engine will lay
+          out the parity bytes it stores on the flash.
+          This property can be automatically determined by
+          the flash geometry (particularly the NAND page
+          and OOB size) in many cases, but when booting
+          from NAND, the boot controller has only a limited
+          number of available options for its default ECC
+          layout.
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+allOf:
+  - $ref: nand-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: brcm,nand-bcm63138
+    then:
+      properties:
+        reg-names:
+          minItems: 2
+          maxItems: 2
+          items:
+            - const: nand
+            - const: nand-int-base
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: brcm,nand-bcm6368
+    then:
+      properties:
+        reg-names:
+          minItems: 3
+          maxItems: 3
+          items:
+            - const: nand
+            - const: nand-int-base
+            - const: nand-cache
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: brcm,nand-iproc
+    then:
+      properties:
+        reg-names:
+          minItems: 3
+          maxItems: 3
+          items:
+            - const: nand
+            - const: iproc-idm
+            - const: iproc-ext
+
+unevaluatedProperties: false
+
+required:
+  - reg
+  - reg-names
+  - interrupts
+
+examples:
+  - |
+    nand-controller@f0442800 {
+            compatible = "brcm,brcmnand-v7.0", "brcm,brcmnand";
+            reg = <0xf0442800 0x600>,
+                  <0xf0443000 0x100>;
+            reg-names = "nand", "flash-dma";
+            interrupt-parent = <&hif_intr2_intc>;
+            interrupts = <24>, <4>;
+
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            nand@1 {
+                    compatible = "brcm,nandcs";
+                    reg = <1>; // Chip select 1
+                    nand-on-flash-bbt;
+                    nand-ecc-strength = <12>;
+                    nand-ecc-step-size = <512>;
+
+                    #address-cells = <1>;
+                    #size-cells = <1>;
+            };
+    };
+  - |
+    nand-controller@10000200 {
+            compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368",
+                         "brcm,brcmnand-v4.0", "brcm,brcmnand";
+            reg = <0x10000200 0x180>,
+                  <0x100000b0 0x10>,
+                  <0x10000600 0x200>;
+            reg-names = "nand", "nand-int-base", "nand-cache";
+            interrupt-parent = <&periph_intc>;
+            interrupts = <50>;
+            clocks = <&periph_clk 20>;
+            clock-names = "nand";
+
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            nand@0 {
+                    compatible = "brcm,nandcs";
+                    reg = <0>;
+                    nand-on-flash-bbt;
+                    nand-ecc-strength = <1>;
+                    nand-ecc-step-size = <512>;
+
+                    #address-cells = <1>;
+                    #size-cells = <1>;
+            };
+    };
diff --git a/Documentation/devicetree/bindings/mtd/common.txt b/Documentation/devicetree/bindings/mtd/common.txt
index fc068b923d7a..ae16f9ea8606 100644
--- a/Documentation/devicetree/bindings/mtd/common.txt
+++ b/Documentation/devicetree/bindings/mtd/common.txt
@@ -1,15 +1 @@
-* Common properties of all MTD devices
-
-Optional properties:
-- label: user-defined MTD device name. Can be used to assign user
-  friendly names to MTD devices (instead of the flash model or flash
-  controller based name) in order to ease flash device identification
-  and/or describe what they are used for.
-
-Example:
-
-	flash@0 {
-		label = "System-firmware";
-
-		/* flash type specific properties */
-	};
+This file has been moved to mtd.yaml.
diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
index 5e7e5349f9a1..ed590d7c6e37 100644
--- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
@@ -9,6 +9,9 @@ title: SPI NOR flash ST M25Pxx (and similar) serial flash chips
 maintainers:
   - Rob Herring <robh@kernel.org>
 
+allOf:
+  - $ref: "mtd.yaml#"
+
 properties:
   compatible:
     oneOf:
@@ -82,6 +85,9 @@ patternProperties:
   '^partition@':
     type: object
 
+  "^otp(-[0-9]+)?$":
+    type: object
+
 additionalProperties: false
 
 examples:
diff --git a/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml b/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml
new file mode 100644
index 000000000000..2cdf6bf3dc4a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/mtd/microchip,mchp48l640.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Microchip 48l640 (and similar) serial EERAM bindings
+
+maintainers:
+  - Heiko Schocher <hs@denx.de>
+
+description: |
+  The Microchip 48l640 is a 8KByte EERAM connected via SPI.
+
+  datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/20006055B.pdf
+
+properties:
+  compatible:
+    items:
+      - const: microchip,48l640
+
+  reg:
+    maxItems: 1
+
+  spi-max-frequency: true
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    spi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      eeram@0 {
+        compatible = "microchip,48l640";
+        reg = <0>;
+        spi-max-frequency = <20000000>;
+      };
+    };
+...
diff --git a/Documentation/devicetree/bindings/mtd/mtd.yaml b/Documentation/devicetree/bindings/mtd/mtd.yaml
new file mode 100644
index 000000000000..376b679cfc70
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mtd.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mtd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MTD (Memory Technology Device) Device Tree Bindings
+
+maintainers:
+  - Miquel Raynal <miquel.raynal@bootlin.com>
+  - Richard Weinberger <richard@nod.at>
+
+properties:
+  $nodename:
+    pattern: "^flash(@.*)?$"
+
+  label:
+    description:
+      User-defined MTD device name. Can be used to assign user friendly
+      names to MTD devices (instead of the flash model or flash controller
+      based name) in order to ease flash device identification and/or
+      describe what they are used for.
+
+patternProperties:
+  "^otp(-[0-9]+)?$":
+    type: object
+    $ref: ../nvmem/nvmem.yaml#
+
+    description: |
+      An OTP memory region. Some flashes provide a one-time-programmable
+      memory whose content can either be programmed by a user or is already
+      pre-programmed by the factory. Some flashes might provide both.
+
+    properties:
+      compatible:
+        enum:
+          - user-otp
+          - factory-otp
+
+    required:
+      - compatible
+
+additionalProperties: true
+
+examples:
+  - |
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        flash@0 {
+            reg = <0>;
+            compatible = "jedec,spi-nor";
+            label = "System-firmware";
+        };
+    };
+
+  - |
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        flash@0 {
+            reg = <0>;
+            compatible = "jedec,spi-nor";
+
+            otp-1 {
+                compatible = "factory-otp";
+                #address-cells = <1>;
+                #size-cells = <1>;
+
+                electronic-serial-number@0 {
+                    reg = <0 8>;
+                };
+            };
+
+            otp-2 {
+                compatible = "user-otp";
+                #address-cells = <1>;
+                #size-cells = <1>;
+
+                mac-address@0 {
+                    reg = <0 6>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
index 678b39952502..bd217e6f5018 100644
--- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
+++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
@@ -38,6 +38,17 @@ properties:
 
   ranges: true
 
+  cs-gpios:
+    minItems: 1
+    maxItems: 8
+    description:
+      Array of chip-select available to the controller. The first
+      entries are a 1:1 mapping of the available chip-select on the
+      NAND controller (even if they are not used). As many additional
+      chip-select as needed may follow and should be phandles of GPIO
+      lines. 'reg' entries of the NAND chip subnodes become indexes of
+      this array when this property is present.
+
 patternProperties:
   "^nand@[a-f0-9]$":
     type: object
@@ -164,14 +175,19 @@ examples:
     nand-controller {
       #address-cells = <1>;
       #size-cells = <0>;
+      cs-gpios = <0>, <&gpioA 1>; /* A single native CS is available */
 
       /* controller specific properties */
 
       nand@0 {
-        reg = <0>;
+        reg = <0>; /* Native CS */
         nand-use-soft-ecc-engine;
         nand-ecc-algo = "bch";
 
         /* controller specific properties */
       };
+
+      nand@1 {
+        reg = <1>; /* GPIO CS */
+      };
     };
diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt b/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt
index b677147ca4e1..c2175d3c82ec 100644
--- a/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt
+++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt
@@ -28,6 +28,11 @@ detected by a software parsing TRX header.
 Required properties:
 - compatible : (required) must be "brcm,trx"
 
+Optional properties:
+
+- brcm,trx-magic: TRX magic, if it is different from the default magic
+		  0x30524448 as a u32.
+
 Example:
 
 flash@0 {
diff --git a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
deleted file mode 100644
index ccfd37b8a0ad..000000000000
--- a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
+++ /dev/null
@@ -1,51 +0,0 @@
-Bindings for HyperBus Memory Controller (HBMC) on TI's K3 family of SoCs
-
-Required properties:
-- compatible : "ti,am654-hbmc" for AM654 SoC
-- reg : Two entries:
-	First entry pointed to the register space of HBMC controller
-	Second entry pointing to the memory map region dedicated for
-	MMIO access to attached flash devices
-- ranges : Address translation from offset within CS to allocated MMIO
-	   space in SoC
-
-Optional properties:
-- mux-controls : phandle to the multiplexer that controls selection of
-		 HBMC vs OSPI inside Flash SubSystem (FSS). Default is OSPI,
-		 if property is absent.
-		 See Documentation/devicetree/bindings/mux/reg-mux.yaml
-		 for mmio-mux binding details
-
-Example:
-
-	system-controller@47000000 {
-		compatible = "syscon", "simple-mfd";
-		reg = <0x0 0x47000000 0x0 0x100>;
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		hbmc_mux: multiplexer {
-			compatible = "mmio-mux";
-			#mux-control-cells = <1>;
-			mux-reg-masks = <0x4 0x2>; /* 0: reg 0x4, bit 1 */
-		};
-	};
-
-	hbmc: hyperbus@47034000 {
-		compatible = "ti,am654-hbmc";
-		reg = <0x0 0x47034000 0x0 0x100>,
-			<0x5 0x00000000 0x1 0x0000000>;
-		power-domains = <&k3_pds 55>;
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */
-			 <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */
-		mux-controls = <&hbmc_mux 0>;
-
-		/* Slave flash node */
-		flash@0,0 {
-			compatible = "cypress,hyperflash", "cfi-flash";
-			reg = <0x0 0x0 0x4000000>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.yaml b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.yaml
new file mode 100644
index 000000000000..30b458c41cac
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.yaml
@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/ti,am654-hbmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HyperBus Memory Controller (HBMC) on TI's K3 family of SoCs
+
+maintainers:
+  - Vignesh Raghavendra <vigneshr@ti.com>
+
+properties:
+  compatible:
+    const: ti,am654-hbmc
+
+  reg:
+    maxItems: 2
+
+  power-domains: true
+  '#address-cells': true
+  '#size-cells': true
+  ranges: true
+
+  mux-controls:
+    description: MMIO mux controller node to select b/w OSPI and HBMC.
+
+  clocks:
+    maxItems: 1
+
+patternProperties:
+  "^flash@[0-1],[0-9a-f]+$":
+    type: object
+
+required:
+  - compatible
+  - reg
+  - ranges
+  - clocks
+  - '#address-cells'
+  - '#size-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    bus {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      hbmc: memory-controller@47034000 {
+        compatible = "ti,am654-hbmc";
+        reg = <0x0 0x47034000 0x0 0x100>,
+              <0x5 0x00000000 0x1 0x0000000>;
+        ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */
+                 <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */
+        clocks = <&k3_clks 102 0>;
+        #address-cells = <2>;
+        #size-cells = <1>;
+        power-domains = <&k3_pds 55>;
+        mux-controls = <&hbmc_mux 0>;
+
+        flash@0,0 {
+            compatible = "cypress,hyperflash", "cfi-flash";
+            reg = <0x0 0x0 0x4000000>;
+            #address-cells = <1>;
+            #size-cells = <1>;
+        };
+      };
+    };