Merge branch 'spi-5.3' into spi-next

13 files changed, 637 insertions, 297 deletions

diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
index 7f0cd72f47d2..699fd3c9ace8 100644
--- a/Documentation/devicetree/bindings/mfd/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
@@ -17,17 +17,24 @@ Required properties for USART in SPI mode:
 - cs-gpios: chipselects (internal cs not supported)
 - atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
 
+Optional properties in serial and SPI mode:
+- dma bindings for dma transfer:
+	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+		memory peripheral interface and USART DMA channel ID, FIFO configuration.
+		The order of DMA channels is fixed. The first DMA channel must be TX
+		associated channel and the second one must be RX associated channel.
+		Refer to dma.txt and atmel-dma.txt for details.
+	- dma-names: "tx" for TX channel.
+		     "rx" for RX channel.
+		     The order of dma-names is also fixed. The first name must be "tx"
+		     and the second one must be "rx" as in the examples below.
+
 Optional properties in serial mode:
 - atmel,use-dma-rx: use of PDC or DMA for receiving data
 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
 - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
   It will use specified PIO instead of the peripheral function pin for the USART feature.
   If unsure, don't specify this property.
-- add dma bindings for dma transfer:
-	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
-		memory peripheral interface and USART DMA channel ID, FIFO configuration.
-		Refer to dma.txt and atmel-dma.txt for details.
-	- dma-names: "rx" for RX channel, "tx" for TX channel.
 - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
   capable USARTs.
 - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
@@ -81,5 +88,8 @@ Example:
 		interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
 		clocks = <&usart0_clk>;
 		clock-names = "usart";
+		dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
+		       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+		dma-names = "tx", "rx";
 		cs-gpios = <&pioB 3 0>;
 	};
diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml
new file mode 100644
index 000000000000..c374fd4923a6
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/allwinner,sun4i-a10-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A10 SPI Controller Device Tree Bindings
+
+allOf:
+  - $ref: "spi-controller.yaml"
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    const: allwinner,sun4i-a10-spi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: ahb
+      - const: mod
+
+  dmas:
+    items:
+      - description: RX DMA Channel
+      - description: TX DMA Channel
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx
+
+  num-cs: true
+
+patternProperties:
+  "^.*@[0-9a-f]+":
+    properties:
+      reg:
+        items:
+          minimum: 0
+          maximum: 4
+
+      spi-rx-bus-width:
+        const: 1
+
+      spi-tx-bus-width:
+        const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    spi1: spi@1c06000 {
+        compatible = "allwinner,sun4i-a10-spi";
+        reg = <0x01c06000 0x1000>;
+        interrupts = <11>;
+        clocks = <&ahb_gates 21>, <&spi1_clk>;
+        clock-names = "ahb", "mod";
+        #address-cells = <1>;
+        #size-cells = <0>;
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
new file mode 100644
index 000000000000..bda7a5befd8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
@@ -0,0 +1,106 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/allwinner,sun6i-a31-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A31 SPI Controller Device Tree Bindings
+
+allOf:
+  - $ref: "spi-controller.yaml"
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    enum:
+      - allwinner,sun6i-a31-spi
+      - allwinner,sun8i-h3-spi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: ahb
+      - const: mod
+
+  resets:
+    maxItems: 1
+
+  dmas:
+    items:
+      - description: RX DMA Channel
+      - description: TX DMA Channel
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx
+
+  num-cs: true
+
+patternProperties:
+  "^.*@[0-9a-f]+":
+    properties:
+      reg:
+        items:
+          minimum: 0
+          maximum: 4
+
+      spi-rx-bus-width:
+        const: 1
+
+      spi-tx-bus-width:
+        const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    spi1: spi@1c69000 {
+        compatible = "allwinner,sun6i-a31-spi";
+        reg = <0x01c69000 0x1000>;
+        interrupts = <0 66 4>;
+        clocks = <&ahb1_gates 21>, <&spi1_clk>;
+        clock-names = "ahb", "mod";
+        resets = <&ahb1_rst 21>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+    };
+
+  - |
+    spi0: spi@1c68000 {
+        compatible = "allwinner,sun8i-h3-spi";
+        reg = <0x01c68000 0x1000>;
+        interrupts = <0 65 4>;
+        clocks = <&ccu 30>, <&ccu 82>;
+        clock-names = "ahb", "mod";
+        dmas = <&dma 23>, <&dma 23>;
+        dma-names = "rx", "tx";
+        resets = <&ccu 15>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt
index 1f6e86f787ef..e07783505498 100644
--- a/Documentation/devicetree/bindings/spi/spi-bus.txt
+++ b/Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -1,111 +1 @@
-SPI (Serial Peripheral Interface) busses
-
-SPI busses can be described with a node for the SPI controller device
-and a set of child nodes for each SPI slave on the bus.  The system's SPI
-controller may be described for use in SPI master mode or in SPI slave mode,
-but not for both at the same time.
-
-The SPI controller node requires the following properties:
-- compatible      - Name of SPI bus controller following generic names
-		    recommended practice.
-
-In master mode, the SPI controller node requires the following additional
-properties:
-- #address-cells  - number of cells required to define a chip select
-		address on the SPI bus.
-- #size-cells     - should be zero.
-
-In slave mode, the SPI controller node requires one additional property:
-- spi-slave       - Empty property.
-
-No other properties are required in the SPI bus node.  It is assumed
-that a driver for an SPI bus device will understand that it is an SPI bus.
-However, the binding does not attempt to define the specific method for
-assigning chip select numbers.  Since SPI chip select configuration is
-flexible and non-standardized, it is left out of this binding with the
-assumption that board specific platform code will be used to manage
-chip selects.  Individual drivers can define additional properties to
-support describing the chip select layout.
-
-Optional properties (master mode only):
-- cs-gpios	  - gpios chip select.
-- num-cs	  - total number of chipselects.
-
-If cs-gpios is used the number of chip selects will be increased automatically
-with max(cs-gpios > hw cs).
-
-So if for example the controller has 2 CS lines, and the cs-gpios
-property looks like this:
-
-cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>;
-
-Then it should be configured so that num_chipselect = 4 with the
-following mapping:
-
-cs0 : &gpio1 0 0
-cs1 : native
-cs2 : &gpio1 1 0
-cs3 : &gpio1 2 0
-
-
-SPI slave nodes must be children of the SPI controller node.
-
-In master mode, one or more slave nodes (up to the number of chip selects) can
-be present.  Required properties are:
-- compatible      - Name of SPI device following generic names recommended
-		    practice.
-- reg             - Chip select address of device.
-- spi-max-frequency - Maximum SPI clocking speed of device in Hz.
-
-In slave mode, the (single) slave node is optional.
-If present, it must be called "slave".  Required properties are:
-- compatible      - Name of SPI device following generic names recommended
-		    practice.
-
-All slave nodes can contain the following optional properties:
-- spi-cpol        - Empty property indicating device requires inverse clock
-		    polarity (CPOL) mode.
-- spi-cpha        - Empty property indicating device requires shifted clock
-		    phase (CPHA) mode.
-- spi-cs-high     - Empty property indicating device requires chip select
-		    active high.
-- spi-3wire       - Empty property indicating device requires 3-wire mode.
-- spi-lsb-first   - Empty property indicating device requires LSB first mode.
-- spi-tx-bus-width - The bus width (number of data wires) that is used for MOSI.
-		    Defaults to 1 if not present.
-- spi-rx-bus-width - The bus width (number of data wires) that is used for MISO.
-		    Defaults to 1 if not present.
-- spi-rx-delay-us - Microsecond delay after a read transfer.
-- spi-tx-delay-us - Microsecond delay after a write transfer.
-
-Some SPI controllers and devices support Dual and Quad SPI transfer mode.
-It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4
-wires (QUAD).
-Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is
-only 1 (SINGLE), 2 (DUAL) and 4 (QUAD).
-Dual/Quad mode is not allowed when 3-wire mode is used.
-
-If a gpio chipselect is used for the SPI slave the gpio number will be passed
-via the SPI master node cs-gpios property.
-
-SPI example for an MPC5200 SPI bus:
-	spi@f00 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-		reg = <0xf00 0x20>;
-		interrupts = <2 13 0 2 14 0>;
-		interrupt-parent = <&mpc5200_pic>;
-
-		ethernet-switch@0 {
-			compatible = "micrel,ks8995m";
-			spi-max-frequency = <1000000>;
-			reg = <0>;
-		};
-
-		codec@1 {
-			compatible = "ti,tlv320aic26";
-			spi-max-frequency = <100000>;
-			reg = <1>;
-		};
-	};
+This file has moved to spi-controller.yaml.
diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml
new file mode 100644
index 000000000000..876c0623f322
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml
@@ -0,0 +1,161 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SPI Controller Generic Binding
+
+maintainers:
+  - Mark Brown <broonie@kernel.org>
+
+description: |
+  SPI busses can be described with a node for the SPI controller device
+  and a set of child nodes for each SPI slave on the bus. The system SPI
+  controller may be described for use in SPI master mode or in SPI slave mode,
+  but not for both at the same time.
+
+properties:
+  $nodename:
+    pattern: "^spi(@.*|-[0-9a-f])*$"
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  cs-gpios:
+    description: |
+      GPIOs used as chip selects.
+      If that property is used, the number of chip selects will be
+      increased automatically with max(cs-gpios, hardware chip selects).
+
+      So if, for example, the controller has 2 CS lines, and the
+      cs-gpios looks like this
+        cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>;
+
+      Then it should be configured so that num_chipselect = 4, with
+      the following mapping
+        cs0 : &gpio1 0 0
+        cs1 : native
+        cs2 : &gpio1 1 0
+        cs3 : &gpio1 2 0
+
+  num-cs:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Total number of chip selects.
+
+  spi-slave:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The SPI controller acts as a slave, instead of a master.
+
+patternProperties:
+  "^slave$":
+    type: object
+
+    properties:
+      compatible:
+        description:
+          Compatible of the SPI device.
+
+    required:
+      - compatible
+
+  "^.*@[0-9a-f]+$":
+    type: object
+
+    properties:
+      compatible:
+        description:
+          Compatible of the SPI device.
+
+      reg:
+        maxItems: 1
+        minimum: 0
+        maximum: 256
+        description:
+          Chip select used by the device.
+
+      spi-3wire:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires 3-wire mode.
+
+      spi-cpha:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires shifted clock phase (CPHA) mode.
+
+      spi-cpol:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires inverse clock polarity (CPOL) mode.
+
+      spi-cs-high:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires the chip select active high.
+
+      spi-lsb-first:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires the LSB first mode.
+
+      spi-max-frequency:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Maximum SPI clocking speed of the device in Hz.
+
+      spi-rx-bus-width:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [ 1, 2, 4 ]
+          - default: 1
+        description:
+          Bus width to the SPI bus used for MISO.
+
+      spi-rx-delay-us:
+        description:
+          Delay, in microseconds, after a read transfer.
+
+      spi-tx-bus-width:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [ 1, 2, 4 ]
+          - default: 1
+        description:
+          Bus width to the SPI bus used for MOSI.
+
+      spi-tx-delay-us:
+        description:
+          Delay, in microseconds, after a write transfer.
+
+    required:
+      - compatible
+      - reg
+
+examples:
+  - |
+    spi@f00 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+        reg = <0xf00 0x20>;
+        interrupts = <2 13 0 2 14 0>;
+        interrupt-parent = <&mpc5200_pic>;
+
+        ethernet-switch@0 {
+            compatible = "micrel,ks8995m";
+            spi-max-frequency = <1000000>;
+            reg = <0>;
+        };
+
+        codec@1 {
+            compatible = "ti,tlv320aic26";
+            spi-max-frequency = <100000>;
+            reg = <1>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.txt b/Documentation/devicetree/bindings/spi/spi-gpio.txt
deleted file mode 100644
index 52db562f17a4..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-gpio.txt
+++ /dev/null
@@ -1,43 +0,0 @@
-SPI-GPIO devicetree bindings
-
-This represents a group of 3-n GPIO lines used for bit-banged SPI on dedicated
-GPIO lines.
-
-Required properties:
-
- - compatible: should be set to "spi-gpio"
- - #address-cells: should be set to <0x1>
- - ranges
- - sck-gpios: GPIO spec for the SCK line to use
- - miso-gpios: GPIO spec for the MISO line to use
- - mosi-gpios: GPIO spec for the MOSI line to use
- - cs-gpios: GPIOs to use for chipselect lines.
-             Not needed if num-chipselects = <0>.
- - num-chipselects: Number of chipselect lines. Should be <0> if a single device
-                    with no chip select is connected.
-
-Deprecated bindings:
-
-These legacy GPIO line bindings can alternatively be used to define the
-GPIO lines used, they should not be used in new device trees.
-
- - gpio-sck: GPIO spec for the SCK line to use
- - gpio-miso: GPIO spec for the MISO line to use
- - gpio-mosi: GPIO spec for the MOSI line to use
-
-Example:
-
-	spi {
-		compatible = "spi-gpio";
-		#address-cells = <0x1>;
-		ranges;
-
-		sck-gpios = <&gpio 95 0>;
-		miso-gpios = <&gpio 98 0>;
-		mosi-gpios = <&gpio 97 0>;
-		cs-gpios = <&gpio 125 0>;
-		num-chipselects = <1>;
-
-		/* clients */
-	};
-
diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.yaml b/Documentation/devicetree/bindings/spi/spi-gpio.yaml
new file mode 100644
index 000000000000..55c4f1705f07
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-gpio.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SPI-GPIO devicetree bindings
+
+maintainers:
+  - Rob Herring <robh@kernel.org>
+
+description:
+  This represents a group of 3-n GPIO lines used for bit-banged SPI on
+  dedicated GPIO lines.
+
+allOf:
+  - $ref: "/schemas/spi/spi-controller.yaml#"
+
+properties:
+  compatible:
+    const: spi-gpio
+
+  sck-gpios:
+    description: GPIO spec for the SCK line to use
+    maxItems: 1
+
+  miso-gpios:
+    description: GPIO spec for the MISO line to use
+    maxItems: 1
+
+  mosi-gpios:
+    description: GPIO spec for the MOSI line to use
+    maxItems: 1
+
+  cs-gpios:
+    description: GPIOs to use for chipselect lines.
+      Not needed if num-chipselects = <0>.
+    minItems: 1
+    maxItems: 1024
+
+  num-chipselects:
+    description: Number of chipselect lines. Should be <0> if a single device
+      with no chip select is connected.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  # Deprecated properties
+  gpio-sck: false
+  gpio-miso: false
+  gpio-mosi: false
+
+required:
+  - compatible
+  - num-chipselects
+  - sck-gpios
+
+examples:
+  - |
+    spi {
+      compatible = "spi-gpio";
+      #address-cells = <0x1>;
+      #size-cells = <0x0>;
+
+      sck-gpios = <&gpio 95 0>;
+      miso-gpios = <&gpio 98 0>;
+      mosi-gpios = <&gpio 97 0>;
+      cs-gpios = <&gpio 125 0>;
+      num-chipselects = <1>;
+
+      /* clients */
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/spi/spi-pl022.yaml b/Documentation/devicetree/bindings/spi/spi-pl022.yaml
new file mode 100644
index 000000000000..dfb697c69341
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-pl022.yaml
@@ -0,0 +1,165 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-pl022.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ARM PL022 SPI controller
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+# We need a select here so we don't match all nodes with 'arm,primecell'
+select:
+  properties:
+    compatible:
+      contains:
+        const: arm,pl022
+  required:
+    - compatible
+
+properties:
+  compatible:
+    items:
+      - const: arm,pl022
+      - const: arm,primecell
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - enum:
+          - SSPCLK
+          - sspclk
+      - const: apb_pclk
+
+  pl022,autosuspend-delay:
+    description: delay in ms following transfer completion before the
+      runtime power management system suspends the device. A setting of 0
+      indicates no delay and the device will be suspended immediately.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  pl022,rt:
+    description: indicates the controller should run the message pump with realtime
+               priority to minimise the transfer latency on the bus (boolean)
+    type: boolean
+
+  dmas:
+    description:
+      Two or more DMA channel specifiers following the convention outlined
+      in bindings/dma/dma.txt
+    minItems: 2
+    maxItems: 32
+
+  dma-names:
+    description:
+      There must be at least one channel named "tx" for transmit and named "rx"
+      for receive.
+    minItems: 2
+    maxItems: 32
+    additionalItems: true
+    items:
+      - const: rx
+      - const: tx
+
+patternProperties:
+  "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$":
+    type: object
+    # SPI slave nodes must be children of the SPI master node and can
+    # contain the following properties.
+    properties:
+      pl022,interface:
+        description: SPI interface type
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum:
+              - 0  # SPI
+              - 1  # Texas Instruments Synchronous Serial Frame Format
+              - 2  # Microwire (Half Duplex)
+
+      pl022,com-mode:
+        description: Specifies the transfer mode
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum:
+              - 0  # interrupt mode
+              - 1  # polling mode
+              - 2  # DMA mode
+            default: 1
+
+      pl022,rx-level-trig:
+        description: Rx FIFO watermark level
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 4
+
+      pl022,tx-level-trig:
+        description: Tx FIFO watermark level
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 4
+
+      pl022,ctrl-len:
+        description: Microwire interface - Control length
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0x03
+            maximum: 0x1f
+
+      pl022,wait-state:
+        description: Microwire interface - Wait state
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum: [ 0, 1 ]
+
+      pl022,duplex:
+        description: Microwire interface - Full/Half duplex
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum: [ 0, 1 ]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    spi@e0100000 {
+      compatible = "arm,pl022", "arm,primecell";
+      reg = <0xe0100000 0x1000>;
+      #address-cells = <1>;
+      #size-cells = <0>;
+      interrupts = <0 31 0x4>;
+      dmas = <&dma_controller 23 1>,
+        <&dma_controller 24 0>;
+      dma-names = "rx", "tx";
+
+      m25p80@1 {
+        compatible = "st,m25p80";
+        reg = <1>;
+        spi-max-frequency = <12000000>;
+        spi-cpol;
+        spi-cpha;
+        pl022,interface = <0>;
+        pl022,com-mode = <0x2>;
+        pl022,rx-level-trig = <0>;
+        pl022,tx-level-trig = <0>;
+        pl022,ctrl-len = <0x11>;
+        pl022,wait-state = <0>;
+        pl022,duplex = <0>;
+      };
+    };
+...
diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
index adeeb63e84b9..bfc038b9478d 100644
--- a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
+++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
@@ -19,8 +19,11 @@ Required properties:
 - reg: chip-Select number (QSPI controller may connect 2 flashes)
 - spi-max-frequency: max frequency of spi bus
 
-Optional property:
+Optional properties:
 - spi-rx-bus-width: see ./spi-bus.txt for the description
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+Documentation/devicetree/bindings/dma/dma.txt.
+- dma-names: DMA request names should include "tx" and "rx" if present.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/spi/spi-sun4i.txt b/Documentation/devicetree/bindings/spi/spi-sun4i.txt
deleted file mode 100644
index c75d604a8290..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-sun4i.txt
+++ /dev/null
@@ -1,23 +0,0 @@
-Allwinner A10 SPI controller
-
-Required properties:
-- compatible: Should be "allwinner,sun4-a10-spi".
-- reg: Should contain register location and length.
-- interrupts: Should contain interrupt.
-- clocks: phandle to the clocks feeding the SPI controller. Two are
-          needed:
-  - "ahb": the gated AHB parent clock
-  - "mod": the parent module clock
-- clock-names: Must contain the clock names described just above
-
-Example:
-
-spi1: spi@1c06000 {
-	compatible = "allwinner,sun4i-a10-spi";
-	reg = <0x01c06000 0x1000>;
-	interrupts = <11>;
-	clocks = <&ahb_gates 21>, <&spi1_clk>;
-	clock-names = "ahb", "mod";
-	#address-cells = <1>;
-	#size-cells = <0>;
-};
diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt
deleted file mode 100644
index 435a8e0731ac..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-sun6i.txt
+++ /dev/null
@@ -1,44 +0,0 @@
-Allwinner A31/H3 SPI controller
-
-Required properties:
-- compatible: Should be "allwinner,sun6i-a31-spi" or "allwinner,sun8i-h3-spi".
-- reg: Should contain register location and length.
-- interrupts: Should contain interrupt.
-- clocks: phandle to the clocks feeding the SPI controller. Two are
-          needed:
-  - "ahb": the gated AHB parent clock
-  - "mod": the parent module clock
-- clock-names: Must contain the clock names described just above
-- resets: phandle to the reset controller asserting this device in
-          reset
-
-Optional properties:
-- dmas: DMA specifiers for rx and tx dma. See the DMA client binding,
-	Documentation/devicetree/bindings/dma/dma.txt
-- dma-names: DMA request names should include "rx" and "tx" if present.
-
-Example:
-
-spi1: spi@1c69000 {
-	compatible = "allwinner,sun6i-a31-spi";
-	reg = <0x01c69000 0x1000>;
-	interrupts = <0 66 4>;
-	clocks = <&ahb1_gates 21>, <&spi1_clk>;
-	clock-names = "ahb", "mod";
-	resets = <&ahb1_rst 21>;
-};
-
-spi0: spi@1c68000 {
-	compatible = "allwinner,sun8i-h3-spi";
-	reg = <0x01c68000 0x1000>;
-	interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
-	clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
-	clock-names = "ahb", "mod";
-	dmas = <&dma 23>, <&dma 23>;
-	dma-names = "rx", "tx";
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi0_pins>;
-	resets = <&ccu RST_BUS_SPI0>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-};
diff --git a/Documentation/devicetree/bindings/spi/spi-synquacer.txt b/Documentation/devicetree/bindings/spi/spi-synquacer.txt
new file mode 100644
index 000000000000..291dfa692d0a
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-synquacer.txt
@@ -0,0 +1,27 @@
+* Socionext Synquacer HS-SPI bindings
+
+Required Properties:
+- compatible: should be "socionext,synquacer-spi"
+- reg: physical base address of the controller and length of memory mapped
+       region.
+- interrupts: should contain the "spi_rx", "spi_tx" and "spi_fault" interrupts.
+- clocks: core clock iHCLK. Optional rate clock iPCLK (default is iHCLK)
+- clock-names: Shall be "iHCLK" and "iPCLK" respectively
+
+Optional Properties:
+- socionext,use-rtm: boolean, if required to use "retimed clock" for RX
+- socionext,set-aces: boolean, if same active clock edges field to be set.
+
+Example:
+
+	spi0: spi@ff110000 {
+		compatible = "socionext,synquacer-spi";
+		reg = <0xff110000 0x1000>;
+		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_hsspi>;
+		clock-names = "iHCLK";
+		socionext,use-rtm;
+		socionext,set-aces;
+	};
diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt
deleted file mode 100644
index 7638b4968ddb..000000000000
--- a/Documentation/devicetree/bindings/spi/spi_pl022.txt
+++ /dev/null
@@ -1,70 +0,0 @@
-ARM PL022 SPI controller
-
-Required properties:
-- compatible : "arm,pl022", "arm,primecell"
-- reg : Offset and length of the register set for the device
-- interrupts : Should contain SPI controller interrupt
-- num-cs : total number of chipselects
-
-Optional properties:
-- cs-gpios : should specify GPIOs used for chipselects.
-  The gpios will be referred to as reg = <index> in the SPI child nodes.
-  If unspecified, a single SPI device without a chip select can be used.
-- pl022,autosuspend-delay : delay in ms following transfer completion before
-			    the runtime power management system suspends the
-			    device. A setting of 0 indicates no delay and the
-                            device will be suspended immediately
-- pl022,rt : indicates the controller should run the message pump with realtime
-             priority to minimise the transfer latency on the bus (boolean)
-- dmas : Two or more DMA channel specifiers following the convention outlined
-         in bindings/dma/dma.txt
-- dma-names: Names for the dma channels, if present. There must be at
-	     least one channel named "tx" for transmit and named "rx" for
-             receive.
-
-
-SPI slave nodes must be children of the SPI master node and can
-contain the following properties.
-
-- pl022,interface : interface type:
-	0: SPI
-	1: Texas Instruments Synchronous Serial Frame Format
-	2: Microwire (Half Duplex)
-- pl022,com-mode : specifies the transfer mode:
-	0: interrupt mode
-	1: polling mode (default mode if property not present)
-	2: DMA mode
-- pl022,rx-level-trig : Rx FIFO watermark level
-- pl022,tx-level-trig : Tx FIFO watermark level
-- pl022,ctrl-len : Microwire interface: Control length
-- pl022,wait-state : Microwire interface: Wait state
-- pl022,duplex : Microwire interface: Full/Half duplex
-
-
-Example:
-
-	spi@e0100000 {
-		compatible = "arm,pl022", "arm,primecell";
-		reg = <0xe0100000 0x1000>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupts = <0 31 0x4>;
-		dmas = <&dma-controller 23 1>,
-			<&dma-controller 24 0>;
-		dma-names = "rx", "tx";
-
-		m25p80@1 {
-			compatible = "st,m25p80";
-			reg = <1>;
-			spi-max-frequency = <12000000>;
-			spi-cpol;
-			spi-cpha;
-			pl022,interface = <0>;
-			pl022,com-mode = <0x2>;
-			pl022,rx-level-trig = <0>;
-			pl022,tx-level-trig = <0>;
-			pl022,ctrl-len = <0x11>;
-			pl022,wait-state = <0>;
-			pl022,duplex = <0>;
-		};
-	};