Merge tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pinctrl updates from Linus Walleij:
 "This is the bulk pin control changes for the v3.17 merge development
  cycle:

   - get rid of the .disable() callback from the driver callback vtable.

     This callback was abused and counterintuitive since a pin or group
     of pins can be said to always be in some setting, and never really
     disabled.  We now only enable a certain muxing, and move between
     some certain muxings, we never "disable" a mux setting

   - some janitorial moving the MSM, Samsung and Nomadik and drivers to
     their own subdirectories for a clearer view in the subsystem.  This
     will continue

   - kill off the use of the return value from gpiochip_remove(), this
     will be done in parallel in the GPIO subsystem and hopefully not
     trigger too many unchecked return value warnings before we get rid
     of this altogether

   - a huge set of changes and improvements to the Allwinner sunxi
     drivers especially for their latest A23 and A31 SoCs, and some
     ground work for the new sun8i platform family

   - a large set of Rockchip driver improvements adding support for the
     RK3288 SoC

   - advances in migration of older Freescale platforms to pin control,
     especially i.MX1

   - Samsung and Exynos improvements

   - support for the Qualcomm MSM8960 SoC

   - use the gpiolib irqchip helpers for the ST SPEAr and Intel Baytrail
     drivers

   - a bunch of nice janitorial work done with cppcheck"

* tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (61 commits)
  pinctrl: baytrail: Convert to use gpiolib irqchip
  pinctrl: sunxi: number gpio ranges starting from 0
  pinctrl: sunxi: use gpiolib API to mark a GPIO used as an IRQ
  pinctrl: rockchip: add drive-strength control for rk3288
  pinctrl: rockchip: add separate type for rk3288
  pinctrl: rockchip: set is_generic in pinconf_ops
  pinctrl: msm: drop negativity check on unsigned value
  pinctrl: remove all usage of gpio_remove ret val in driver/pinctl
  pinctrl: qcom: Make muxing of gpio function explicit
  pinctrl: nomadik: move all Nomadik drivers to subdir
  pinctrl: samsung: Group all drivers in a sub-dir
  sh-pfc: sh73a0: Introduce the use of devm_regulator_register
  sh-pfc: Add renesas,pfc-r8a7791 to binding documentation
  pinctrl: msm: move all qualcomm drivers to subdir
  pinctrl: msm: Add msm8960 definitions
  pinctrl: samsung: Allow pin value to be initialized using pinfunc
  pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes
  pinctrl: exynos: Consolidate irq_chips of GPIO and WKUP EINTs
  pinctrl: samsung: Handle GPIO request and free using pinctrl helpers
  pinctrl: samsung: Decouple direction setting from pinctrl
  ...

8 files changed, 213 insertions, 5 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index d8d065608ec0..93ce12eb422a 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -13,6 +13,8 @@ Required properties:
   "allwinner,sun6i-a31-pinctrl"
   "allwinner,sun6i-a31-r-pinctrl"
   "allwinner,sun7i-a20-pinctrl"
+  "allwinner,sun8i-a23-pinctrl"
+  "allwinner,sun8i-a23-r-pinctrl"
 - reg: Should contain the register physical address and length for the
   pin controller.
 
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
index 7181f925acaa..0211c6d8a522 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
@@ -46,7 +46,7 @@ Valid values for pins are:
   gpio0-gpio89
 
 Valid values for function are:
-  cam_mclk, codec_mic_i2s, codec_spkr_i2s, gsbi1, gsbi2, gsbi3, gsbi4,
+  cam_mclk, codec_mic_i2s, codec_spkr_i2s, gpio, gsbi1, gsbi2, gsbi3, gsbi4,
   gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6,
   gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1,
   gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm,
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
index e0d35a40981b..e33e4dcdce79 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
@@ -51,7 +51,7 @@ Valid values for qcom,pins are:
 
 
 Valid values for function are:
-  mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gsbi1, gsbi2, gsbi4, gsbi5,
+  mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gpio, gsbi1, gsbi2, gsbi4, gsbi5,
   gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1,
   spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata,
   pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt,
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt
new file mode 100644
index 000000000000..93b7de91b9f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt
@@ -0,0 +1,181 @@
+Qualcomm MSM8960 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8960 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,msm8960-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    gpio0-gpio151,
+		    sdc1_clk,
+		    sdc1_cmd,
+		    sdc1_data
+		    sdc3_clk,
+		    sdc3_cmd,
+		    sdc3_data
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+		    audio_pcm, bt, cam_mclk0, cam_mclk1, cam_mclk2,
+		    codec_mic_i2s, codec_spkr_i2s, ext_gps, fm, gps_blanking,
+		    gps_pps_in, gps_pps_out, gp_clk_0a, gp_clk_0b, gp_clk_1a,
+		    gp_clk_1b, gp_clk_2a, gp_clk_2b, gp_mn, gp_pdm_0a,
+		    gp_pdm_0b, gp_pdm_1a, gp_pdm_1b, gp_pdm_2a, gp_pdm_2b, gpio,
+		    gsbi1, gsbi1_spi_cs1_n, gsbi1_spi_cs2a_n, gsbi1_spi_cs2b_n,
+		    gsbi1_spi_cs3_n, gsbi2, gsbi2_spi_cs1_n, gsbi2_spi_cs2_n,
+		    gsbi2_spi_cs3_n, gsbi3, gsbi4, gsbi4_3d_cam_i2c_l,
+		    gsbi4_3d_cam_i2c_r, gsbi5, gsbi5_3d_cam_i2c_l,
+		    gsbi5_3d_cam_i2c_r, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10,
+		    gsbi11, gsbi11_spi_cs1a_n, gsbi11_spi_cs1b_n,
+		    gsbi11_spi_cs2a_n, gsbi11_spi_cs2b_n, gsbi11_spi_cs3_n,
+		    gsbi12, hdmi_cec, hdmi_ddc_clock, hdmi_ddc_data,
+		    hdmi_hot_plug_detect, hsic, mdp_vsync, mi2s, mic_i2s,
+		    pmb_clk, pmb_ext_ctrl, ps_hold, rpm_wdog, sdc2, sdc4, sdc5,
+		    slimbus1, slimbus2, spkr_i2s, ssbi1, ssbi2, ssbi_ext_gps,
+		    ssbi_pmic2, ssbi_qpa1, ssbi_ts, tsif1, tsif2, ts_eoc,
+		    usb_fs1, usb_fs1_oe, usb_fs1_oe_n, usb_fs2, usb_fs2_oe,
+		    usb_fs2_oe_n, vfe_camif_timer1_a, vfe_camif_timer1_b,
+		    vfe_camif_timer2, vfe_camif_timer3_a, vfe_camif_timer3_b,
+		    vfe_camif_timer4_a, vfe_camif_timer4_b, vfe_camif_timer4_c,
+		    vfe_camif_timer5_a, vfe_camif_timer5_b, vfe_camif_timer6_a,
+		    vfe_camif_timer6_b, vfe_camif_timer6_c, vfe_camif_timer7_a,
+		    vfe_camif_timer7_b, vfe_camif_timer7_c, wlan
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+		    Not valid for sdc pins.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+		    Not valid for sdc pins.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	msmgpio: pinctrl@800000 {
+		compatible = "qcom,msm8960-pinctrl";
+		reg = <0x800000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 16 0x4>;
+
+		gsbi8_uart: gsbi8-uart {
+			mux {
+				pins = "gpio34", "gpio35";
+				function = "gsbi8";
+			};
+
+			tx {
+				pins = "gpio34";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio35";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
index 73262b575dfc..d2ea80dc43eb 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
@@ -70,7 +70,7 @@ Valid values for function are:
   cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc,
   hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk,
   gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s,
-  ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus
+  ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, gpio
 
   (Note that this is not yet the complete list of functions)
 
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
index 35d2e1f186f0..daef6fad6a5f 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
@@ -15,6 +15,7 @@ Required Properties:
     - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller.
     - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller.
     - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller.
+    - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2) compatible pin-controller.
     - "renesas,pfc-sh7372": for SH7372 (SH-Mobile AP4) compatible pin-controller.
     - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller.
 
diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
index cefef741a40b..4658b69d4f4d 100644
--- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
@@ -21,6 +21,7 @@ defined as gpio sub-nodes of the pinmux controller.
 Required properties for iomux controller:
   - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl"
 		       "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl"
+		       "rockchip,rk3288-pinctrl"
   - rockchip,grf: phandle referencing a syscon providing the
 	 "general register files"
 
@@ -36,7 +37,7 @@ Deprecated properties for iomux controller:
 	 Use rockchip,grf and rockchip,pmu described above instead.
 
 Required properties for gpio sub nodes:
-  - compatible: "rockchip,gpio-bank", "rockchip,rk3188-gpio-bank0"
+  - compatible: "rockchip,gpio-bank"
   - reg: register of the gpio bank (different than the iomux registerset)
   - interrupts: base interrupt of the gpio bank in the interrupt controller
   - clocks: clock that drives this bank
@@ -50,6 +51,7 @@ Required properties for gpio sub nodes:
     bindings/interrupt-controller/interrupts.txt
 
 Deprecated properties for gpio sub nodes:
+  - compatible: "rockchip,rk3188-gpio-bank0"
   - reg: second element: separate pull register for rk3188 bank0, use
 	 rockchip,pmu described above instead
 
diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
index 2b32783ba821..e82aaf492517 100644
--- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -44,7 +44,11 @@ Required Properties:
 - Pin mux/config groups as child nodes: The pin mux (selecting pin function
   mode) and pin config (pull up/down, driver strength) settings are represented
   as child nodes of the pin-controller node. There should be atleast one
-  child node and there is no limit on the count of these child nodes.
+  child node and there is no limit on the count of these child nodes. It is
+  also possible for a child node to consist of several further child nodes
+  to allow grouping multiple pinctrl groups into one. The format of second
+  level child nodes is exactly the same as for first level ones and is
+  described below.
 
   The child node should contain a list of pin(s) on which a particular pin
   function selection or pin configuration (or both) have to applied. This
@@ -71,6 +75,7 @@ Required Properties:
   "samsung,pins" property of the child node. The following pin configuration
   properties are supported.
 
+  - samsung,pin-val: Initial value of pin output buffer.
   - samsung,pin-pud: Pull up/down configuration.
   - samsung,pin-drv: Drive strength configuration.
   - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
@@ -249,6 +254,23 @@ Example 1: A pin-controller node with pin groups.
 			samsung,pin-pud = <3>;
 			samsung,pin-drv = <0>;
 		};
+
+		sd4_bus8: sd4-bus-width8 {
+			part-1 {
+				samsung,pins = "gpk0-3", "gpk0-4",
+						"gpk0-5", "gpk0-6";
+				samsung,pin-function = <3>;
+				samsung,pin-pud = <3>;
+				samsung,pin-drv = <3>;
+			};
+			part-2 {
+				samsung,pins = "gpk1-3", "gpk1-4",
+						"gpk1-5", "gpk1-6";
+				samsung,pin-function = <4>;
+				samsung,pin-pud = <4>;
+				samsung,pin-drv = <3>;
+			};
+		};
 	};
 
 Example 2: A pin-controller node with external wakeup interrupt controller node.