Merge branch 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "Summary:

   - legacy PM code removed from the core, there were no users anymore
     (thanks to Lars-Peter Clausen)

   - new driver for Broadcom iProc

   - bigger driver updates for designware, rk3x, cadence, ocores

   - a bunch of smaller updates and bugfixes"

* 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (31 commits)
  i2c: ocores: rework clk code to handle NULL cookie
  i2c: designware-baytrail: another fixup for proper Kconfig dependencies
  i2c: fix reference to functionality constants definition
  i2c: iproc: Add Broadcom iProc I2C Driver
  i2c: designware-pci: update Intel copyright line
  i2c: ocores: add common clock support
  i2c: hix5hd2: add COMPILE_TEST
  i2c: clarify comments about the dev_released completion
  i2c: ocores: fix clock-frequency binding usage
  i2c: tegra: Maintain CPU endianness
  i2c: designware-baytrail: use proper Kconfig dependencies
  i2c: designware: Do not calculate SCL timing parameters needlessly
  i2c: do not try to load modules for of-registered devices
  i2c: designware: Add Intel Baytrail PMIC I2C bus support
  i2c: designware: Add i2c bus locking support
  of: i2c: Add i2c-mux-idle-disconnect DT property to PCA954x mux driver
  i2c: designware: use {readl|writel}_relaxed instead of readl/writel
  i2c: designware-pci: no need to provide clk_khz
  i2c: designware-pci: remove Moorestown support
  i2c: imx: whitespace and checkpatch cleanup
  ...

5 files changed, 95 insertions, 6 deletions

diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
new file mode 100644
index 000000000000..81f982ccca31
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
@@ -0,0 +1,37 @@
+Broadcom iProc I2C controller
+
+Required properties:
+
+- compatible:
+    Must be "brcm,iproc-i2c"
+
+- reg:
+    Define the base and range of the I/O address space that contain the iProc
+    I2C controller registers
+
+- interrupts:
+    Should contain the I2C interrupt
+
+- clock-frequency:
+    This is the I2C bus clock. Need to be either 100000 or 400000
+
+- #address-cells:
+    Always 1 (for I2C addresses)
+
+- #size-cells:
+    Always 0
+
+Example:
+	i2c0: i2c@18008000 {
+		compatible = "brcm,iproc-i2c";
+		reg = <0x18008000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+		clock-frequency = <100000>;
+
+		codec: wm8750@1a {
+			compatible = "wlf,wm8750";
+			reg = <0x1a>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
index 34a3fb6f8488..cf53d5fba20a 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
@@ -16,6 +16,9 @@ Required Properties:
 Optional Properties:
 
   - reset-gpios: Reference to the GPIO connected to the reset input.
+  - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
+    children in idle state. This is necessary for example, if there are several
+    multiplexers on the bus and the devices behind them use same I2C addresses.
 
 
 Example:
diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
index 1637c298a1b3..17bef9a34e50 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
@@ -4,24 +4,60 @@ Required properties:
 - compatible      : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst"
 - reg             : bus address start and address range size of device
 - interrupts      : interrupt number
-- clock-frequency : frequency of bus clock in Hz
+- clocks          : handle to the controller clock; see the note below.
+                    Mutually exclusive with opencores,ip-clock-frequency
+- opencores,ip-clock-frequency: frequency of the controller clock in Hz;
+                    see the note below. Mutually exclusive with clocks
 - #address-cells  : should be <1>
 - #size-cells     : should be <0>
 
 Optional properties:
+- clock-frequency : frequency of bus clock in Hz; see the note below.
+                    Defaults to 100 KHz when the property is not specified
 - reg-shift       : device register offsets are shifted by this value
 - reg-io-width    : io register width in bytes (1, 2 or 4)
 - regstep         : deprecated, use reg-shift above
 
-Example:
+Note
+clock-frequency property is meant to control the bus frequency for i2c bus
+drivers, but it was incorrectly used to specify i2c controller input clock
+frequency. So the following rules are set to fix this situation:
+- if clock-frequency is present and neither opencores,ip-clock-frequency nor
+  clocks are, then clock-frequency specifies i2c controller clock frequency.
+  This is to keep backwards compatibility with setups using old DTB. i2c bus
+  frequency is fixed at 100 KHz.
+- if clocks is present it specifies i2c controller clock. clock-frequency
+  property specifies i2c bus frequency.
+- if opencores,ip-clock-frequency is present it specifies i2c controller
+  clock frequency. clock-frequency property specifies i2c bus frequency.
 
+Examples:
+
+	i2c0: ocores@a0000000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "opencores,i2c-ocores";
+		reg = <0xa0000000 0x8>;
+		interrupts = <10>;
+		opencores,ip-clock-frequency = <20000000>;
+
+		reg-shift = <0>;	/* 8 bit registers */
+		reg-io-width = <1>;	/* 8 bit read/write */
+
+		dummy@60 {
+			compatible = "dummy";
+			reg = <0x60>;
+		};
+	};
+or
 	i2c0: ocores@a0000000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "opencores,i2c-ocores";
 		reg = <0xa0000000 0x8>;
 		interrupts = <10>;
-		clock-frequency = <20000000>;
+		clocks = <&osc>;
+		clock-frequency = <400000>; /* i2c bus frequency 400 KHz */
 
 		reg-shift = <0>;	/* 8 bit registers */
 		reg-io-width = <1>;	/* 8 bit read/write */
diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt
index dde6c22ce91a..f0d71bc52e64 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt
@@ -21,6 +21,17 @@ Required on RK3066, RK3188 :
 Optional properties :
 
  - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used.
+ - i2c-scl-rising-time-ns : Number of nanoseconds the SCL signal takes to rise
+	(t(r) in I2C specification). If not specified this is assumed to be
+	the maximum the specification allows(1000 ns for Standard-mode,
+	300 ns for Fast-mode) which might cause slightly slower communication.
+ - i2c-scl-falling-time-ns : Number of nanoseconds the SCL signal takes to fall
+	(t(f) in the I2C specification). If not specified this is assumed to
+	be the maximum the specification allows (300 ns) which might cause
+	slightly slower communication.
+ - i2c-sda-falling-time-ns : Number of nanoseconds the SDA signal takes to fall
+	(t(f) in the I2C specification). If not specified we'll use the SCL
+	value since they are the same in nearly all cases.
 
 Example:
 
@@ -39,4 +50,7 @@ i2c0: i2c@2002d000 {
 
 	clock-names = "i2c";
 	clocks = <&cru PCLK_I2C0>;
+
+	i2c-scl-rising-time-ns = <800>;
+	i2c-scl-falling-time-ns = <100>;
 };
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 4dcd88d5f7ca..aaa8325004d2 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -61,9 +61,8 @@ fsl,sgtl5000		SGTL5000: Ultra Low-Power Audio Codec
 gmt,g751		G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface
 infineon,slb9635tt	Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz)
 infineon,slb9645tt	Infineon SLB9645 I2C TPM (new protocol, max 400khz)
-isl,isl12057		Intersil ISL12057 I2C RTC Chip
-isil,isl29028           (deprecated, use isl)
-isl,isl29028            Intersil ISL29028 Ambient Light and Proximity Sensor
+isil,isl12057		Intersil ISL12057 I2C RTC Chip
+isil,isl29028		Intersil ISL29028 Ambient Light and Proximity Sensor
 maxim,ds1050		5 Bit Programmable, Pulse-Width Modulator
 maxim,max1237		Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs
 maxim,max6625		9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface