Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2017-02-19

Here's a set of Bluetooth patches for the 4.11 kernel:

 - New USB IDs to the btusb driver
 - Race fix in btmrvl driver
 - Added out-of-band wakeup support to the btusb driver
 - NULL dereference fix to bt_sock_recvmsg

Please let me know if there are any issues pulling. Thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

2 files changed, 81 insertions, 8 deletions

diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt
new file mode 100644
index 000000000000..01fa2d4188d4
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/btusb.txt
@@ -0,0 +1,43 @@
+Generic Bluetooth controller over USB (btusb driver)
+---------------------------------------------------
+
+Required properties:
+
+  - compatible : should comply with the format "usbVID,PID" specified in
+		 Documentation/devicetree/bindings/usb/usb-device.txt
+		 At the time of writing, the only OF supported devices
+		 (more may be added later) are:
+
+		  "usb1286,204e" (Marvell 8997)
+
+Also, vendors that use btusb may have device additional properties, e.g:
+Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
+
+Optional properties:
+
+  - interrupt-parent: phandle of the parent interrupt controller
+  - interrupt-names: (see below)
+  - interrupts : The interrupt specified by the name "wakeup" is the interrupt
+		 that shall be used for out-of-band wake-on-bt. Driver will
+		 request this interrupt for wakeup. During system suspend, the
+		 irq will be enabled so that the bluetooth chip can wakeup host
+		 platform out of band. During system resume, the irq will be
+		 disabled to make sure unnecessary interrupt is not received.
+
+Example:
+
+Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt:
+
+&usb_host1_ehci {
+    status = "okay";
+    #address-cells = <1>;
+    #size-cells = <0>;
+
+    mvl_bt1: bt@1 {
+	compatible = "usb1286,204e";
+	reg = <1>;
+	interrupt-parent = <&gpio0>;
+	interrupt-name = "wakeup";
+	interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+    };
+};
diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
index 6a9a63cb0543..9be1059ff03f 100644
--- a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
+++ b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
@@ -1,16 +1,21 @@
-Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices
+Marvell 8897/8997 (sd8897/sd8997) bluetooth devices (SDIO or USB based)
 ------
+The 8997 devices supports multiple interfaces. When used on SDIO interfaces,
+the btmrvl driver is used and when used on USB interface, the btusb driver is
+used.
 
 Required properties:
 
   - compatible : should be one of the following:
-	* "marvell,sd8897-bt"
-	* "marvell,sd8997-bt"
+	* "marvell,sd8897-bt" (for SDIO)
+	* "marvell,sd8997-bt" (for SDIO)
+	* "usb1286,204e"      (for USB)
 
 Optional properties:
 
   - marvell,cal-data: Calibration data downloaded to the device during
 		      initialization. This is an array of 28 values(u8).
+		      This is only applicable to SDIO devices.
 
   - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip.
 		        firmware will use the pin to wakeup host system (u16).
@@ -18,10 +23,15 @@ Optional properties:
 		      platform. The value will be configured to firmware. This
 		      is needed to work chip's sleep feature as expected (u16).
   - interrupt-parent: phandle of the parent interrupt controller
-  - interrupts : interrupt pin number to the cpu. Driver will request an irq based
-		 on this interrupt number. During system suspend, the irq will be
-		 enabled so that the bluetooth chip can wakeup host platform under
-		 certain condition. During system resume, the irq will be disabled
+  - interrupt-names: Used only for USB based devices (See below)
+  - interrupts : specifies the interrupt pin number to the cpu. For SDIO, the
+		 driver will use the first interrupt specified in the interrupt
+		 array. For USB based devices, the driver will use the interrupt
+		 named "wakeup" from the interrupt-names and interrupt arrays.
+		 The driver will request an irq based on this interrupt number.
+		 During system suspend, the irq will be enabled so that the
+		 bluetooth chip can wakeup host platform under certain
+		 conditions. During system resume, the irq will be disabled
 		 to make sure unnecessary interrupt is not received.
 
 Example:
@@ -29,7 +39,9 @@ Example:
 IRQ pin 119 is used as system wakeup source interrupt.
 wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host
 using this device side pin and wakeup latency.
-calibration data is also available in below example.
+
+Example for SDIO device follows (calibration data is also available in
+below example).
 
 &mmc3 {
 	status = "okay";
@@ -54,3 +66,21 @@ calibration data is also available in below example.
 		marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
 	};
 };
+
+Example for USB device:
+
+&usb_host1_ohci {
+    status = "okay";
+    #address-cells = <1>;
+    #size-cells = <0>;
+
+    mvl_bt1: bt@1 {
+	compatible = "usb1286,204e";
+	reg = <1>;
+	interrupt-parent = <&gpio0>;
+	interrupt-names = "wakeup";
+	interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
+	marvell,wakeup-pin = /bits/ 16 <0x0d>;
+	marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
+    };
+};