Merge tag 'v4.20' into next

Merge with mainline to bring in the new APIs.

39 files changed, 83 insertions, 53 deletions

diff --git a/Documentation/devicetree/bindings/input/cypress,cyapa.txt b/Documentation/devicetree/bindings/input/cypress,cyapa.txt
index 8d91ba9ff2fd..d3db65916a36 100644
--- a/Documentation/devicetree/bindings/input/cypress,cyapa.txt
+++ b/Documentation/devicetree/bindings/input/cypress,cyapa.txt
@@ -3,8 +3,6 @@ Cypress I2C Touchpad
 Required properties:
 - compatible: must be "cypress,cyapa".
 - reg: I2C address of the chip.
-- interrupt-parent: a phandle for the interrupt controller (see interrupt
-	binding[0]).
 - interrupts: interrupt to which the chip is connected (see interrupt
 	binding[0]).
 
diff --git a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt
index f517660a3204..ef2ae729718f 100644
--- a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt
+++ b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt
@@ -6,8 +6,6 @@ Required properties:
     * "cypress,midas-touchkey" - for the touchkey found on midas boards
     * "cypress,aries-touchkey" - for the touchkey found on aries boards
 - reg: I2C address of the chip.
-- interrupt-parent: a phandle for the interrupt controller (see interrupt
-	binding[0]).
 - interrupts: interrupt to which the chip is connected (see interrupt
 	binding[0]).
 - vcc-supply : internal regulator output. 1.8V
diff --git a/Documentation/devicetree/bindings/input/e3x0-button.txt b/Documentation/devicetree/bindings/input/e3x0-button.txt
index 751665e8e47a..907b195f2eaa 100644
--- a/Documentation/devicetree/bindings/input/e3x0-button.txt
+++ b/Documentation/devicetree/bindings/input/e3x0-button.txt
@@ -7,8 +7,6 @@ This module provides a simple power button event via two interrupts.
 Required properties:
 - compatible: should be one of the following
   - "ettus,e3x0-button": For devices such as the NI Ettus Research USRP E3x0
-- interrupt-parent:
-  - a phandle to the interrupt controller that it is attached to.
 - interrupts: should be one of the following
   - <0 30 1>, <0 31 1>: For devices such as the NI Ettus Research USRP E3x0
 - interrupt-names: should be one of the following
diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt b/Documentation/devicetree/bindings/input/elan_i2c.txt
index d80a83583238..797607460735 100644
--- a/Documentation/devicetree/bindings/input/elan_i2c.txt
+++ b/Documentation/devicetree/bindings/input/elan_i2c.txt
@@ -3,8 +3,6 @@ Elantech I2C Touchpad
 Required properties:
 - compatible: must be "elan,ekth3000".
 - reg: I2C address of the chip.
-- interrupt-parent: a phandle for the interrupt controller (see interrupt
-  binding[0]).
 - interrupts: interrupt to which the chip is connected (see interrupt
   binding[0]).
 
diff --git a/Documentation/devicetree/bindings/input/elants_i2c.txt b/Documentation/devicetree/bindings/input/elants_i2c.txt
index 8a71038f3489..5edac8be0802 100644
--- a/Documentation/devicetree/bindings/input/elants_i2c.txt
+++ b/Documentation/devicetree/bindings/input/elants_i2c.txt
@@ -3,8 +3,6 @@ Elantech I2C Touchscreen
 Required properties:
 - compatible: must be "elan,ekth3500".
 - reg: I2C address of the chip.
-- interrupt-parent: a phandle for the interrupt controller (see interrupt
-  binding[0]).
 - interrupts: interrupt to which the chip is connected (see interrupt
   binding[0]).
 
diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt
index 996ce84352cb..7cccc49b6bea 100644
--- a/Documentation/devicetree/bindings/input/gpio-keys.txt
+++ b/Documentation/devicetree/bindings/input/gpio-keys.txt
@@ -1,4 +1,4 @@
-Device-Tree bindings for input/gpio_keys.c keyboard driver
+Device-Tree bindings for input/keyboard/gpio_keys.c keyboard driver
 
 Required properties:
 	- compatible = "gpio-keys";
diff --git a/Documentation/devicetree/bindings/input/hid-over-i2c.txt b/Documentation/devicetree/bindings/input/hid-over-i2c.txt
index 4d3da9d91de4..c76bafaf98d2 100644
--- a/Documentation/devicetree/bindings/input/hid-over-i2c.txt
+++ b/Documentation/devicetree/bindings/input/hid-over-i2c.txt
@@ -14,7 +14,6 @@ Required properties:
 - compatible: must be "hid-over-i2c"
 - reg: i2c slave address
 - hid-descr-addr: HID descriptor address
-- interrupt-parent: the phandle for the interrupt controller
 - interrupts: interrupt line
 
 Additional optional properties:
@@ -26,7 +25,8 @@ device-specific compatible properties, which should be used in addition to the
 
 - compatible:
   * "wacom,w9013" (Wacom W9013 digitizer). Supports:
-    - vdd-supply
+    - vdd-supply (3.3V)
+    - vddl-supply (1.8V)
     - post-power-on-delay-ms
 
 - vdd-supply: phandle of the regulator that provides the supply voltage.
diff --git a/Documentation/devicetree/bindings/input/input-reset.txt b/Documentation/devicetree/bindings/input/input-reset.txt
index 2bb2626fdb78..1ca6cc5ebf8e 100644
--- a/Documentation/devicetree/bindings/input/input-reset.txt
+++ b/Documentation/devicetree/bindings/input/input-reset.txt
@@ -12,7 +12,7 @@ The /chosen node should contain a 'linux,sysrq-reset-seq' child node to define
 a set of keys.
 
 Required property:
-sysrq-reset-seq: array of Linux keycodes, one keycode per cell.
+keyset: array of Linux keycodes, one keycode per cell.
 
 Optional property:
 timeout-ms: duration keys must be pressed together in milliseconds before
diff --git a/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt b/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt
new file mode 100644
index 000000000000..2888d07c2ef0
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/mtk-pmic-keys.txt
@@ -0,0 +1,43 @@
+MediaTek MT6397/MT6323 PMIC Keys Device Driver
+
+There are two key functions provided by MT6397/MT6323 PMIC, pwrkey
+and homekey. The key functions are defined as the subnode of the function
+node provided by MT6397/MT6323 PMIC that is being defined as one kind
+of Muti-Function Device (MFD)
+
+For MT6397/MT6323 MFD bindings see:
+Documentation/devicetree/bindings/mfd/mt6397.txt
+
+Required properties:
+- compatible: "mediatek,mt6397-keys" or "mediatek,mt6323-keys"
+- linux,keycodes: See Documentation/devicetree/bindings/input/keys.txt
+
+Optional Properties:
+- wakeup-source: See Documentation/devicetree/bindings/power/wakeup-source.txt
+- mediatek,long-press-mode: Long press key shutdown setting, 1 for
+	pwrkey only, 2 for pwrkey/homekey together, others for disabled.
+- power-off-time-sec: See Documentation/devicetree/bindings/input/keys.txt
+
+Example:
+
+	pmic: mt6397 {
+		compatible = "mediatek,mt6397";
+
+		...
+
+		mt6397keys: mt6397keys {
+			compatible = "mediatek,mt6397-keys";
+			mediatek,long-press-mode = <1>;
+			power-off-time-sec = <0>;
+
+			power {
+				linux,keycodes = <116>;
+				wakeup-source;
+			};
+
+			home {
+				linux,keycodes = <114>;
+			};
+		};
+
+	};
diff --git a/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt b/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt
index 5b6232db7c61..99a4f2ab5557 100644
--- a/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt
+++ b/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt
@@ -3,7 +3,6 @@ Raydium I2C touchscreen
 Required properties:
 - compatible: must be "raydium,rm32380"
 - reg: The I2C address of the device
-- interrupt-parent: the phandle for the interrupt controller
 - interrupts: interrupt to which the chip is connected
     See ../interrupt-controller/interrupts.txt
 Optional properties:
diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt
index f2c30c8b725d..9afffbdf6e28 100644
--- a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt
+++ b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt
@@ -12,7 +12,7 @@ Additional documentation for F11 can be found at:
 http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
 
 Optional Touch Properties:
-Description in Documentation/devicetree/bindings/input/touch
+Description in Documentation/devicetree/bindings/input/touchscreen
 - touchscreen-inverted-x
 - touchscreen-inverted-y
 - touchscreen-swapped-x-y
diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt
index ec908b91fd90..dcb012f5b3ee 100644
--- a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt
+++ b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt
@@ -16,7 +16,6 @@ Required Properties:
 
 Optional Properties:
 - interrupts: interrupt which the rmi device is connected to.
-- interrupt-parent: The interrupt controller.
 See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 
 - syna,reset-delay-ms: The number of milliseconds to wait after resetting the
diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt
index a4ca7828f21d..632f473db65b 100644
--- a/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt
+++ b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt
@@ -16,7 +16,6 @@ Required Properties:
 
 Optional Properties:
 - interrupts: interrupt which the rmi device is connected to.
-- interrupt-parent: The interrupt controller.
 See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 
 - spi-rx-delay-us: microsecond delay after a read transfer.
diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt
index f99fe5cdeaec..a644408b33b8 100644
--- a/Documentation/devicetree/bindings/input/rotary-encoder.txt
+++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt
@@ -28,7 +28,7 @@ Deprecated properties:
   This property is deprecated. Instead, a 'steps-per-period ' value should
   be used, such as "rotary-encoder,steps-per-period = <2>".
 
-See Documentation/input/rotary-encoder.txt for more information.
+See Documentation/input/devices/rotary-encoder.rst for more information.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt
index a3dde8c30e67..c829e18e1a05 100644
--- a/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt
+++ b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt
@@ -9,7 +9,6 @@ This module provides a simple power button event via an Interrupt.
 Required properties:
 - compatible: should be one of the following
    - "ti,palmas-pwrbutton": For Palmas compatible power on button
-- interrupt-parent: Parent interrupt device, must be handle of palmas node.
 - interrupts: Interrupt number of power button submodule on device.
 
 Optional Properties:
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt
index 3c8614c451f2..cdd743a1f2d5 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt
@@ -5,7 +5,6 @@ Required properties:
 				  for I2C slave, use "adi,ad7879-1"
 - reg				: SPI chipselect/I2C slave address
 				  See spi-bus.txt for more SPI slave properties
-- interrupt-parent		: the phandle for the interrupt controller
 - interrupts			: touch controller interrupt
 - touchscreen-max-pressure	: maximum reported pressure
 - adi,resistance-plate-x	: total resistance of X-plate (for pressure
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt
index 9fc47b006fd1..04413da51391 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt
@@ -18,7 +18,6 @@ Additional required properties:
 					"ti,ads7846"
 					"ti,ads7873"
 
-	interrupt-parent
 	interrupts		An interrupt node describing the IRQ line the chip's
 				!PENIRQ pin is connected to.
 	vcc-supply		A regulator node for the supply voltage.
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt b/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt
index e459e8546f34..82019bd6094e 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt
@@ -3,7 +3,6 @@
 Required properties:
 - compatible		: "microchip,ar1021-i2c"
 - reg			: I2C slave address
-- interrupt-parent	: the phandle for the interrupt controller
 - interrupts		: touch controller interrupt
 
 Example:
diff --git a/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt b/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt
index d11f8d615b5d..38b0603f65f3 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt
@@ -3,8 +3,6 @@
 Required properties:
  - compatible		  : "chipone,icn8318"
  - reg			  : I2C slave address of the chip (0x40)
- - interrupt-parent	  : a phandle pointing to the interrupt controller
-			    serving the interrupt for this chip
  - interrupts		  : interrupt specification for the icn8318 interrupt
  - wake-gpios		  : GPIO specification for the WAKE input
  - touchscreen-size-x	  : horizontal resolution of touchscreen (in pixels)
diff --git a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
index df531b5b6a0d..2e1490a8fe74 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
@@ -7,7 +7,6 @@ Required Properties:
 - xm-gpios: FET gate driver for input of X-
 - yp-gpios: FET gate driver for input of Y+
 - ym-gpios: FET gate driver for input of Y-
-- interrupt-parent: phandle for the interrupt controller
 - interrupts: pen irq interrupt for touch detection
 - pinctrl-names: "idle", "default", "gpios"
 - pinctrl-0: pinctrl node for pen/touch detection state pinmux
diff --git a/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt
index b75d4cfd2c36..6ee274aa8b03 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt
@@ -4,8 +4,6 @@ Required properties:
  - compatible		: must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi"
  - reg			: Device I2C address or SPI chip select number
  - spi-max-frequency	: Maximum SPI clocking speed of the device (for cyttsp-spi)
- - interrupt-parent	: the phandle for the gpio controller
-			  (see interrupt binding[0]).
  - interrupts		: (gpio) interrupt to which the chip is connected
 			  (see interrupt binding[0]).
  - bootloader-key	: the 8-byte bootloader key that is required to switch
diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
index 025cf8c9324a..da2dc5d6c98b 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
@@ -22,8 +22,6 @@ Required properties:
            or:  "focaltech,ft6236"
 
  - reg:         I2C slave address of the chip (0x38)
- - interrupt-parent: a phandle pointing to the interrupt controller
-                     serving the interrupt for this chip
  - interrupts:       interrupt specification for the touchdetect
                      interrupt
 
diff --git a/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt
index 298e3442f143..92fb2620f5e2 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt
@@ -3,7 +3,6 @@
 Required properties:
 - compatible: must be "eeti,egalax_ts"
 - reg: i2c slave address
-- interrupt-parent: the phandle for the interrupt controller
 - interrupts: touch controller interrupt
 - wakeup-gpios: the gpio pin to be used for waking up the controller
   and also used as irq pin
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt
index 5a19f4c3e9d7..94c4fc644940 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt
@@ -3,8 +3,6 @@
 Required properties:
  - compatible		  : "elan,ektf2127"
  - reg			  : I2C slave address of the chip (0x40)
- - interrupt-parent	  : a phandle pointing to the interrupt controller
-			    serving the interrupt for this chip
  - interrupts		  : interrupt specification for the ektf2127 interrupt
  - power-gpios		  : GPIO specification for the pin connected to the
 			    ektf2127's wake input. This needs to be driven high
diff --git a/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt b/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt
index 1dcff4a43eaa..68291b94fec2 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt
@@ -3,7 +3,6 @@
 Required properties:
 - compatible: must be "eeti,exc3000"
 - reg: i2c slave address
-- interrupt-parent: the phandle for the interrupt controller
 - interrupts: touch controller interrupt
 - touchscreen-size-x: See touchscreen.txt
 - touchscreen-size-y: See touchscreen.txt
diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
index abfcab3edc66..99d6f9d25335 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
@@ -8,7 +8,6 @@ Required properties:
  - reg: Memory range of the device.
  - interrupts: Should be the interrupt number associated with this module within
    the tscadc unit (<0>).
- - interrupt-parent: Should be a phandle to the tscadc unit.
  - fsl,wires: Should be '<4>' or '<5>'
 
 Optional properties:
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index 0c369d8ebcab..f7e95c52f3c7 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -11,7 +11,6 @@ Required properties:
 				 or "goodix,gt928"
 				 or "goodix,gt967"
  - reg			: I2C address of the chip. Should be 0x5d or 0x14
- - interrupt-parent	: Interrupt controller to which the chip is connected
  - interrupts		: Interrupt to which the chip is connected
 
 Optional properties:
diff --git a/Documentation/devicetree/bindings/input/touchscreen/hideep.txt b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt
index 121d9b7c79a2..a47c36190b01 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/hideep.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt
@@ -3,7 +3,6 @@
 Required properties:
 - compatible		: must be "hideep,hideep-ts"
 - reg			: I2C slave address, (e.g. 0x6C).
-- interrupt-parent : Interrupt controller to which the chip is connected.
 - interrupts : Interrupt to which the chip is connected.
 
 Optional properties:
@@ -32,7 +31,7 @@ i2c@00000000 {
 		reg = <0x6c>;
 		interrupt-parent = <&gpx1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
-		vdd-supply = <&ldo15_reg>";
+		vdd-supply = <&ldo15_reg>;
 		vid-supply = <&ldo18_reg>;
 		reset-gpios = <&gpx1 5 0>;
 		touchscreen-size-x = <1080>;
diff --git a/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt
index 40ac0fe94df6..05e982c3454e 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt
@@ -3,7 +3,6 @@
 Required properties:
 - compatible: must be "maxim,max11801"
 - reg: i2c slave address
-- interrupt-parent: the phandle for the interrupt controller
 - interrupts: touch controller interrupt
 
 Example:
diff --git a/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt b/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt
index 7b8944c2cb31..b2ab5498e519 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt
@@ -3,7 +3,6 @@
 Required properties:
 - compatible: must be "melfas,mip4_ts"
 - reg: I2C slave address of the chip (0x48 or 0x34)
-- interrupt-parent: interrupt controller to which the chip is connected
 - interrupts: interrupt to which the chip is connected
 
 Optional properties:
diff --git a/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.txt b/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.txt
new file mode 100644
index 000000000000..51456c0e9a27
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.txt
@@ -0,0 +1,30 @@
+Generic resistive touchscreen ADC
+
+Required properties:
+
+ - compatible: must be "resistive-adc-touch"
+The device must be connected to an ADC device that provides channels for
+position measurement and optional pressure.
+Refer to ../iio/iio-bindings.txt for details
+ - iio-channels: must have at least two channels connected to an ADC device.
+These should correspond to the channels exposed by the ADC device and should
+have the right index as the ADC device registers them. These channels
+represent the relative position on the "x" and "y" axes.
+ - iio-channel-names: must have all the channels' names. Mandatory channels
+are "x" and "y".
+
+Optional properties:
+ - iio-channels: The third channel named "pressure" is optional and can be
+used if the ADC device also measures pressure besides position.
+If this channel is missing, pressure will be ignored and the touchscreen
+will only report position.
+ - iio-channel-names: optional channel named "pressure".
+
+Example:
+
+	resistive_touch: resistive_touch {
+		compatible = "resistive-adc-touch";
+		touchscreen-min-pressure = <50000>;
+		io-channels = <&adc 24>, <&adc 25>, <&adc 26>;
+		io-channel-names = "x", "y", "pressure";
+	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt
index d9b7c2ff611e..6805d10d226d 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt
@@ -3,8 +3,6 @@
 Required properties:
 - compatible		: must be "samsung,s6sy761"
 - reg			: I2C slave address, (e.g. 0x48)
-- interrupt-parent	: the phandle to the interrupt controller which provides
-			  the interrupt
 - interrupts		: interrupt specification
 - avdd-supply		: analogic power supply
 - vdd-supply		: power supply
diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt
index 84752de12412..d67e558e5ab5 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt
@@ -8,8 +8,6 @@ Required properties:
 			    "silead,gsl3675"
 			    "silead,gsl3692"
 - reg			  : I2C slave address of the chip (0x40)
-- interrupt-parent	  : a phandle pointing to the interrupt controller
-			    serving the interrupt for this chip
 - interrupts		  : interrupt specification for the gsl1680 interrupt
 - power-gpios		  : Specification for the pin connected to the gsl1680's
 			    shutdown input. This needs to be driven high to take the
diff --git a/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt b/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt
index d87ad14f1efe..8f5322e01024 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt
@@ -3,8 +3,6 @@
 Required properties:
 - compatible: must be "sis,9200-ts"
 - reg: i2c slave address
-- interrupt-parent: the phandle for the interrupt controller
-  (see interrupt binding [0])
 - interrupts: touch controller interrupt (see interrupt
   binding [0])
 
diff --git a/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt b/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt
index 9683595cd0f5..0a5d0cb4a280 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt
@@ -10,8 +10,6 @@ coordinates.
 Required properties:
 - compatible		: must be "st,stmfts"
 - reg			: I2C slave address, (e.g. 0x49)
-- interrupt-parent	: the phandle to the interrupt controller which provides
-			  the interrupt
 - interrupts		: interrupt specification
 - avdd-supply		: analogic power supply
 - vdd-supply		: power supply
diff --git a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt
index 5aaa6b3aa90c..4886c4aa2906 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt
@@ -3,7 +3,6 @@
 Required properties:
 - compatible: must be "semtech,sx8654"
 - reg: i2c slave address
-- interrupt-parent: the phandle for the interrupt controller
 - interrupts: touch controller interrupt
 
 Example:
diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
index 8aff9551259f..8641a2d70851 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
@@ -9,6 +9,9 @@ Optional properties for Touchscreens:
 				  (maximum y coordinate reported + 1)
  - touchscreen-max-pressure	: maximum reported pressure (arbitrary range
 				  dependent on the controller)
+ - touchscreen-min-pressure	: minimum pressure on the touchscreen to be
+				  achieved in order for the touchscreen
+				  driver to report a touch event.
  - touchscreen-fuzz-x		: horizontal noise value of the absolute input
 				  device (in pixels)
  - touchscreen-fuzz-y		: vertical noise value of the absolute input
diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
index ec365e172236..ed00f61b8c08 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
@@ -9,8 +9,6 @@ Optional properties:
 - gpios: the interrupt gpio the chip is connected to (trough the penirq pin).
   The penirq pin goes to low when the panel is touched.
   (see GPIO binding[1] for more details).
-- interrupt-parent: the phandle for the gpio controller
-  (see interrupt binding[0]).
 - interrupts: (gpio) interrupt to which the chip is connected
   (see interrupt binding[0]).
 - ti,max-rt: maximum pressure.
diff --git a/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt b/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt
index fe6a1feef703..27d55a506f18 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt
@@ -3,8 +3,6 @@ Zeitec ZET6223 I2C touchscreen controller
 Required properties:
 - compatible		  : "zeitec,zet6223"
 - reg			  : I2C slave address of the chip (0x76)
-- interrupt-parent	  : a phandle pointing to the interrupt controller
-			    serving the interrupt for this chip
 - interrupts		  : interrupt specification for the zet6223 interrupt
 
 Optional properties: