Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6

Pull device tree changes from Grant Likely:
 "Here are the DT changes I've got queued up for v3.8.  As described
  below, there are a lot of bug fixes here and documentation updates but
  nothing major:

  Bug fixes, little cleanups, and documentation changes.  The most
  invasive thing here touches a bunch of the arch directories to use a
  common build rule for .dtb files.  There are no major changes to
  functionality here other than a few new helper functions."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
  arm64: Fix the dtbs target building
  mtd: nand: davinci: fix the binding documentation
  rtc: rtc-mv: Add the device tree binding documentation
  devicetree/bindings: Move gpio-leds binding into leds directory
  of/vendor-prefixes: add Imagination Technologies
  microblaze: use new common dtc rule
  c6x: use new common dtc rule
  openrisc: use new common dtc rule
  arm64: Add dtbs target for building all the enabled dtb files
  arm64: use new common dtc rule
  ARM: dt: change .dtb build rules to build in dts directory
  kbuild: centralize .dts->.dtb rule
  Fix build when CONFIG_W1_MASTER_GPIO=m b exporting "allnodes"
  of/spi: Honour "status=disabled" property of device
  of_mdio: Honour "status=disabled" property of device
  of_i2c: Honour "status=disabled" property of device
  powerpc: Fix fallout from device_node->name constification
  of: add 'const' for of_parse_phandle parameter *np
  Documentation: correct of_platform_populate() argument list
  script: dtc: clean generated files
  ...

1 files changed, 0 insertions, 58 deletions

diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt
deleted file mode 100644
index edc83c1c0d54..000000000000
--- a/Documentation/devicetree/bindings/gpio/led.txt
+++ /dev/null
@@ -1,58 +0,0 @@
-LEDs connected to GPIO lines
-
-Required properties:
-- compatible : should be "gpio-leds".
-
-Each LED is represented as a sub-node of the gpio-leds device.  Each
-node's name represents the name of the corresponding LED.
-
-LED sub-node properties:
-- gpios :  Should specify the LED's GPIO, see "gpios property" in
-  Documentation/devicetree/bindings/gpio/gpio.txt.  Active low LEDs should be
-  indicated using flags in the GPIO specifier.
-- label :  (optional) The label for this LED.  If omitted, the label is
-  taken from the node name (excluding the unit address).
-- linux,default-trigger :  (optional) This parameter, if present, is a
-  string defining the trigger assigned to the LED.  Current triggers are:
-    "backlight" - LED will act as a back-light, controlled by the framebuffer
-		  system
-    "default-on" - LED will turn on, but see "default-state" below
-    "heartbeat" - LED "double" flashes at a load average based rate
-    "ide-disk" - LED indicates disk activity
-    "timer" - LED flashes at a fixed, configurable rate
-- default-state:  (optional) The initial state of the LED.  Valid
-  values are "on", "off", and "keep".  If the LED is already on or off
-  and the default-state property is set the to same value, then no
-  glitch should be produced where the LED momentarily turns off (or
-  on).  The "keep" setting will keep the LED at whatever its current
-  state is, without producing a glitch.  The default is off if this
-  property is not present.
-
-Examples:
-
-leds {
-	compatible = "gpio-leds";
-	hdd {
-		label = "IDE Activity";
-		gpios = <&mcu_pio 0 1>; /* Active low */
-		linux,default-trigger = "ide-disk";
-	};
-
-	fault {
-		gpios = <&mcu_pio 1 0>;
-		/* Keep LED on if BIOS detected hardware fault */
-		default-state = "keep";
-	};
-};
-
-run-control {
-	compatible = "gpio-leds";
-	red {
-		gpios = <&mpc8572 6 0>;
-		default-state = "off";
-	};
-	green {
-		gpios = <&mpc8572 7 0>;
-		default-state = "on";
-	};
-};