diff options
author | Arnd Bergmann <arnd@arndb.de> | 2018-01-04 17:05:06 +0100 |
---|---|---|
committer | Arnd Bergmann <arnd@arndb.de> | 2018-01-04 17:05:06 +0100 |
commit | 3bfbed8d83a5c48d6c43178402a93b90c342a8f1 (patch) | |
tree | f609831e26cf7922aea60d6094da8932d57ce6c1 | |
parent | fbd90b4cae105fbd8364fa1ce3f41d0c06296f58 (diff) | |
parent | 7d2901f809c110bd9a261e879d59efe62e3bc758 (diff) |
Merge tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v4.15" from Simon Horman:
Vladimir Zapolskiy says:
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the change is also a safety improvement because it
removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Note that DTS files for V3M Starter Kit, Draak and Eagle boards
contain the same property, the files are untouched due to unavailable
schematics to verify if the fix applies to these boards as well.
* tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
arm64: dts: renesas: salvator-x: Remove renesas, no-ether-link property
-rw-r--r-- | arch/arm64/boot/dts/renesas/salvator-common.dtsi | 1 | ||||
-rw-r--r-- | arch/arm64/boot/dts/renesas/ulcb.dtsi | 1 |
2 files changed, 0 insertions, 2 deletions
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi index a298df74ca6c..dbe2648649db 100644 --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi @@ -255,7 +255,6 @@ &avb { pinctrl-0 = <&avb_pins>; pinctrl-names = "default"; - renesas,no-ether-link; phy-handle = <&phy0>; status = "okay"; diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi index 0d85b315ce71..73439cf48659 100644 --- a/arch/arm64/boot/dts/renesas/ulcb.dtsi +++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi @@ -145,7 +145,6 @@ &avb { pinctrl-0 = <&avb_pins>; pinctrl-names = "default"; - renesas,no-ether-link; phy-handle = <&phy0>; status = "okay"; |