/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * * mkamsboot.c - a tool for merging bootloader code into an Sansa V2 * (AMS) firmware file * * Copyright (C) 2008 Dave Chapman * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ /* Insert a Rockbox bootloader into a Sansa AMS original firmware file. Layout of a Sansa AMS original firmware file: ---------------------- 0x0 | HEADER | |----------------------| 0x400 | FIRMWARE BLOCK | (contains the OF version on some fuzev2 firmwares |----------------------| 0x600 | FIRMWARE BLOCK | |----------------------| 0x400 + firmware block size | LIBRARIES/DATA | ---------------------- END We replace the main firmware block while preserving the potential OF version (bytes 0x600..0x400+firmware_size) as follows: ---------------------- 0x0 | | | Dual-boot code | | | |----------------------| | EMPTY SPACE | |----------------------| | | | compressed RB image | | | |----------------------| | | | compressed OF image | | | |----------------------| | UCL unpack function | ---------------------- This entire block fits into the space previously occupied by the main firmware block - the space saved by compressing the OF image is used to store the compressed version of the Rockbox bootloader. On version 1 firmwares, the OF image is typically about 120KB, which allows us to store a Rockbox bootloader with an uncompressed size of about 60KB-70KB. Version 2 firmwares are bigger and are stored in SDRAM (instead of IRAM). In both cases, the RAM we are using is mapped at offset 0x0. mkamsboot then corrects the checksums and writes a new legal firmware file which can be installed on the device. When the Sansa device boots, this firmware block is loaded to RAM at address 0x0 and executed. Firstly, the dual-boot code will copy the UCL unpack function to the end of RAM. Then, depending on the detection of the dual-boot keypress, either the OF image or the Rockbox image is copied to the end of RAM (just before the ucl unpack function) and uncompressed to the start of RAM. Finally, the ucl unpack function branches to address 0x0, passing execution to the uncompressed firmware. */ #include #include #include #include #include #include #include #include #include #include "mkamsboot.h" #include "md5.h" /* Header for ARM code binaries */ #include "dualboot.h" /* Win32 compatibility */ #ifndef O_BINARY #define O_BINARY 0 #endif /* fw_revision: version 2 is used in Clipv2, Clip+ and Fuzev2 firmwares */ /* hw_revision: 4 for m200, 2 for e200/c200, 1 or 2 for fuze/clip, 1 for clip+ */ const struct ams_models ams_identity[] = { [MODEL_C200V2] = { 2, 1, "c200", dualboot_c200v2, sizeof(dualboot_c200v2), "c2v2", 44 }, [MODEL_CLIPPLUS]= { 1, 2, "Clip+", dualboot_clipplus, sizeof(dualboot_clipplus), "cli+", 66 }, [MODEL_CLIPV2] = { 2, 2, "Clip", dualboot_clipv2, sizeof(dualboot_clipv2), "clv2", 60 }, [MODEL_CLIP] = { 1, 1, "Clip", dualboot_clip, sizeof(dualboot_clip), "clip", 40 }, [MODEL_E200V2] = { 2, 1, "e200", dualboot_e200v2, sizeof(dualboot_e200v2), "e2v2", 41 }, [MODEL_FUZEV2] = { 2, 2, "Fuze", dualboot_fuzev2, sizeof(dualboot_fuzev2), "fuz2", 68 }, [MODEL_FUZE] = { 1, 1, "Fuze", dualboot_fuze, sizeof(dualboot_fuze), "fuze", 43 }, [MODEL_M200V4] = { 4, 1, "m200", dualboot_m200v4, sizeof(dualboot_m200v4), "m2v4", 42 }, [MODEL_CLIPZIP] = { 1, 2, "ClipZip", dualboot_clipzip, sizeof(dualboot_clipzip), "clzp", 79 }, }; /* Checksums of unmodified original firmwares - for safety, and device detection */ static struct md5sums sansasums[] = { /* NOTE: Different regional versions of the firmware normally only differ in the filename - the md5sums are identical */ /* model version md5 */ { MODEL_E200V2, "3.01.11", "e622ca8cb6df423f54b8b39628a1f0a3" }, { MODEL_E200V2, "3.01.14", "2c1d0383fc3584b2cc83ba8cc2243af6" }, { MODEL_E200V2, "3.01.16", "12563ad71b25a1034cf2092d1e0218c4" }, { MODEL_FUZE, "1.01.11", "cac8ffa03c599330ac02c4d41de66166" }, { MODEL_FUZE, "1.01.15", "df0e2c1612727f722c19a3c764cff7f2" }, { MODEL_FUZE, "1.01.22", "5aff5486fe8dd64239cc71eac470af98" }, { MODEL_FUZE, "1.02.26", "7c632c479461c48c8833baed74eb5e4f" }, { MODEL_FUZE, "1.02.28", "5b34260f6470e75f702a9c6825471752" }, { MODEL_FUZE, "1.02.31", "66d01b37462a5ef7ccc6ad37188b4235" }, { MODEL_C200V2, "3.02.05", "b6378ebd720b0ade3fad4dc7ab61c1a5" }, { MODEL_M200V4, "4.00.45", "82e3194310d1514e3bbcd06e84c4add3" }, { MODEL_M200V4, "4.01.08-A", "fc9dd6116001b3e6a150b898f1b091f0" }, { MODEL_M200V4, "4.01.08-E", "d3fb7d8ec8624ee65bc99f8dab0e2369" }, { MODEL_CLIP, "1.01.17", "12caad785d506219d73f538772afd99e" }, { MODEL_CLIP, "1.01.18", "d720b266bd5afa38a198986ef0508a45" }, { MODEL_CLIP, "1.01.20", "236d8f75189f468462c03f6d292cf2ac" }, { MODEL_CLIP, "1.01.29", "c12711342169c66e209540cd1f27cd26" }, { MODEL_CLIP, "1.01.30", "f2974d47c536549c9d8259170f1dbe4d" }, { MODEL_CLIP, "1.01.32", "d835d12342500732ffb9c4ee54abec15" }, { MODEL_CLIP, "1.01.35", "b4d0edb3b8f2a4e8eee0a344f7f8e480" }, { MODEL_CLIPV2, "2.01.16", "c57fb3fcbe07c2c9b360f060938f80cb" }, { MODEL_CLIPV2, "2.01.32", "0ad3723e52022509089d938d0fbbf8c5" }, { MODEL_CLIPV2, "2.01.35", "a3cbbd22b9508d7f8a9a1a39acc342c2" }, { MODEL_CLIPPLUS, "01.02.09", "656d38114774c2001dc18e6726df3c5d" }, { MODEL_CLIPPLUS, "01.02.13", "5f89872b79ef440b0e5ee3a7a44328b2" }, { MODEL_CLIPPLUS, "01.02.15", "680a4f521e790ad25b93b1b16f3a207d" }, { MODEL_CLIPPLUS, "01.02.16", "055a53de1dfb09f6cb71c504ad48bd13" }, { MODEL_CLIPPLUS, "01.02.18", "80b547244438b113e2a55ff0305f12c0" }, { MODEL_FUZEV2, "2.01.17", "8b85fb05bf645d08a4c8c3e344ec9ebe" }, { MODEL_FUZEV2, "2.02.26", "d4f6f85c3e4a8ea8f2e5acc421641801" }, { MODEL_FUZEV2, "2.03.31", "74fb197ccd51707388f3b233402186a6" }, { MODEL_FUZEV2, "2.03.33", "1599cc73d02ea7fe53fe2d4379c24b66" }, { MODEL_CLIPZIP, "1.01.12", "45adea0873326b5af34f096e5c402f78" }, { MODEL_CLIPZIP, "1.01.15", "f62af954334cd9ba1a87a7fa58ec6074" }, { MODEL_CLIPZIP, "1.01.17", "27bcb343d6950f35dc261629e22ba60c" }, { MODEL_CLIPZIP, "1.01.18", "ef16aa9e02b49885ebede5aa149502e8" }, { MODEL_CLIPZIP, "1.01.20", "d88c8977cc6a952d3f51ece105869d97" }, { MODEL_CLIPZIP, "1.01.21", "92c814d6e3250189706a36d2b49b6152" }, }; #define NUM_MD5S (sizeof(sansasums)/sizeof(sansasums[0])) static unsigned int model_memory_size(int model) { /* The OF boots with IRAM (320kB) mapped at 0x0 */ if(model == MODEL_CLIPV2) { /* The decompressed Clipv2 OF is around 380kB. * Let's use the full IRAM (1MB on AMSv2) */ return 1 << 20; } else { /* The IRAM is 320kB on AMSv1, and 320 will be enough on Fuzev1/Clip+ */ return 320 << 10; } } int firmware_revision(int model) { return ams_identity[model].fw_revision; } static off_t filesize(int fd) { struct stat buf; if (fstat(fd, &buf) < 0) { perror("[ERR] Checking filesize of input file"); return -1; } else { return(buf.st_size); } } static uint32_t get_uint32le(unsigned char* p) { return p[0] | (p[1] << 8) | (p[2] << 16) | (p[3] << 24); } static uint32_t get_uint32be(unsigned char* p) { return (p[0] << 24) | (p[1] << 16) | (p[2] << 8) | p[3]; } static void put_uint32le(unsigned char* p, uint32_t x) { p[0] = x & 0xff; p[1] = (x >> 8) & 0xff; p[2] = (x >> 16) & 0xff; p[3] = (x >> 24) & 0xff; } void calc_MD5(unsigned char* buf, int len, char *md5str) { int i; md5_context ctx; unsigned char md5sum[16]; md5_starts(&ctx); md5_update(&ctx, buf, len); md5_finish(&ctx, md5sum); for (i = 0; i < 16; ++i) sprintf(md5str + 2*i, "%02x", md5sum[i]); } /* Calculate a simple checksum used in Sansa Original Firmwares */ static uint32_t calc_checksum(unsigned char* buf, uint32_t n) { uint32_t sum = 0; uint32_t i; for (i=0;i maxsize) { /* this should NEVER happen, and implies memory corruption */ fprintf(stderr, "internal error - compression failed: %d\n", r); free(outbuf); return NULL; } return outbuf; } #define ERROR(format, ...) \ do { \ snprintf(errstr, errstrsize, format, __VA_ARGS__); \ goto error; \ } while(0) /* Loads a Sansa AMS Original Firmware file into memory */ unsigned char* load_of_file( char* filename, int model, off_t* bufsize, struct md5sums *sum, int* firmware_size, unsigned char** of_packed, int* of_packedsize, char* errstr, int errstrsize) { int fd; unsigned char* buf =NULL; off_t n; unsigned int i=0; uint32_t checksum; unsigned int last_word; fd = open(filename, O_RDONLY|O_BINARY); if (fd < 0) ERROR("[ERR] Could not open %s for reading\n", filename); *bufsize = filesize(fd); buf = malloc(*bufsize); if (buf == NULL) ERROR("[ERR] Could not allocate memory for %s\n", filename); n = read(fd, buf, *bufsize); if (n != *bufsize) ERROR("[ERR] Could not read file %s\n", filename); /* check the file */ /* Calculate MD5 checksum of OF */ calc_MD5(buf, *bufsize, sum->md5); while ((i < NUM_MD5S) && (strcmp(sansasums[i].md5, sum->md5) != 0)) i++; if (i < NUM_MD5S) { *sum = sansasums[i]; if(sum->model != model) { ERROR("[ERR] OF File provided is %sv%d version %s, not for %sv%d\n", ams_identity[sum->model].model_name, ams_identity[sum->model].hw_revision, sum->version, ams_identity[model].model_name, ams_identity[model].hw_revision ); } } else { /* OF unknown, give a list of tested versions for the requested model */ char tested_versions[100]; tested_versions[0] = '\0'; for (i = 0; i < NUM_MD5S ; i++) if (sansasums[i].model == model) { if (tested_versions[0] != '\0') { strncat(tested_versions, ", ", sizeof(tested_versions) - strlen(tested_versions) - 1); } strncat(tested_versions, sansasums[i].version, sizeof(tested_versions) - strlen(tested_versions) - 1); } ERROR("[ERR] Original firmware unknown, please try another version." " Tested %sv%d versions are: %s\n", ams_identity[model].model_name, ams_identity[model].hw_revision, tested_versions); } /* TODO: Do some more sanity checks on the OF image. Some images (like m200v4) dont have a checksum at the end, only padding (0xdeadbeef). */ last_word = *bufsize - 4; checksum = get_uint32le(buf + last_word); if (checksum != 0xefbeadde && checksum != calc_checksum(buf, last_word)) ERROR("%s", "[ERR] Whole file checksum failed\n"); if (ams_identity[sum->model].bootloader == NULL) ERROR("[ERR] Unsupported model - \"%s\"\n", ams_identity[sum->model].model_name); /* Get the firmware size */ if (ams_identity[sum->model].fw_revision == 1) *firmware_size = get_uint32le(&buf[0x0c]); else if (ams_identity[sum->model].fw_revision == 2) *firmware_size = get_uint32le(&buf[0x10]); /* Compress the original firmware image */ *of_packed = uclpack(buf + 0x400, *firmware_size, of_packedsize); if (*of_packed == NULL) ERROR("[ERR] Could not compress %s\n", filename); return buf; error: free(buf); return NULL; } /* Loads a rockbox bootloader file into memory */ unsigned char* load_rockbox_file( char* filename, int *model, int* bufsize, int* rb_packedsize, char* errstr, int errstrsize) { int fd; unsigned char* buf = NULL; unsigned char* packed = NULL; unsigned char header[8]; uint32_t sum; off_t n; int i; fd = open(filename, O_RDONLY|O_BINARY); if (fd < 0) ERROR("[ERR] Could not open %s for reading\n", filename); /* Read Rockbox header */ n = read(fd, header, sizeof(header)); if (n != sizeof(header)) ERROR("[ERR] Could not read file %s\n", filename); for(*model = 0; *model < NUM_MODELS; (*model)++) if (memcmp(ams_identity[*model].rb_model_name, header + 4, 4) == 0) break; if(*model == NUM_MODELS) ERROR("[ERR] Model name \"%4.4s\" unknown. Is this really a rockbox bootloader?\n", header + 4); *bufsize = filesize(fd) - sizeof(header); buf = malloc(*bufsize); if (buf == NULL) ERROR("[ERR] Could not allocate memory for %s\n", filename); n = read(fd, buf, *bufsize); if (n != *bufsize) ERROR("[ERR] Could not read file %s\n", filename); /* Check checksum */ sum = ams_identity[*model].rb_model_num; for (i = 0; i < *bufsize; i++) { /* add 8 unsigned bits but keep a 32 bit sum */ sum += buf[i]; } if (sum != get_uint32be(header)) ERROR("[ERR] Checksum mismatch in %s\n", filename); packed = uclpack(buf, *bufsize, rb_packedsize); if(packed == NULL) ERROR("[ERR] Could not compress %s\n", filename); free(buf); return packed; error: free(buf); return NULL; } #undef ERROR /* Patches a Sansa AMS Original Firmware file */ void patch_firmware( int model, int fw_revision, int firmware_size, unsigned char* buf, int len, unsigned char* of_packed, int of_packedsize, unsigned char* rb_packed, int rb_packedsize) { unsigned char *p; uint32_t sum, filesum; uint32_t ucl_dest; unsigned int i; /* Zero the original firmware area - not needed, but helps debugging */ memset(buf + 0x600, 0, firmware_size); /* Insert dual-boot bootloader at offset 0x200, we preserve the OF * version string located between 0x0 and 0x200 */ memcpy(buf + 0x600, ams_identity[model].bootloader, ams_identity[model].bootloader_size); /* Insert vectors, they won't overwrite the OF version string */ static const uint32_t goto_start = 0xe3a0fc02; // mov pc, #0x200 static const uint32_t infinite_loop = 0xeafffffe; // 1: b 1b /* ALL vectors: infinite loop */ for (i=0; i < 8; i++) put_uint32le(buf + 0x400 + 4*i, infinite_loop); /* Now change only the interesting vectors */ /* Reset/SWI vectors: branch to our dualboot code at 0x200 */ put_uint32le(buf + 0x400 + 4*0, goto_start); // Reset put_uint32le(buf + 0x400 + 4*2, goto_start); // SWI /* We are filling the firmware buffer backwards from the end */ p = buf + 0x400 + firmware_size; /* 1 - UCL unpack function */ p -= sizeof(nrv2e_d8); memcpy(p, nrv2e_d8, sizeof(nrv2e_d8)); /* 2 - Compressed copy of original firmware */ p -= of_packedsize; memcpy(p, of_packed, of_packedsize); /* 3 - Compressed copy of Rockbox bootloader */ p -= rb_packedsize; memcpy(p, rb_packed, rb_packedsize); /* Write the locations of the various images to the variables at the start of the dualboot image - we save the location of the last byte in each image, along with the size in bytes */ /* UCL unpack function */ put_uint32le(&buf[0x604], firmware_size - 1); put_uint32le(&buf[0x608], sizeof(nrv2e_d8)); /* Compressed original firmware image */ put_uint32le(&buf[0x60c], firmware_size - sizeof(nrv2e_d8) - 1); put_uint32le(&buf[0x610], of_packedsize); /* Compressed Rockbox image */ put_uint32le(&buf[0x614], firmware_size - sizeof(nrv2e_d8) - of_packedsize - 1); put_uint32le(&buf[0x618], rb_packedsize); ucl_dest = model_memory_size(model) - 1; /* last byte of memory */ put_uint32le(&buf[0x61c], ucl_dest); /* Update the firmware block checksum */ sum = calc_checksum(buf + 0x400, firmware_size); if (fw_revision == 1) { put_uint32le(&buf[0x04], sum); put_uint32le(&buf[0x204], sum); } else if (fw_revision == 2) { put_uint32le(&buf[0x08], sum); put_uint32le(&buf[0x208], sum); /* Update the header checksums */ put_uint32le(&buf[0x1fc], calc_checksum(buf, 0x1fc)); put_uint32le(&buf[0x3fc], calc_checksum(buf + 0x200, 0x1fc)); } /* Update the whole-file checksum */ filesum = 0; for (i=0;i < (unsigned)len - 4; i+=4) filesum += get_uint32le(&buf[i]); put_uint32le(buf + len - 4, filesum); } /* returns != 0 if the firmware can be safely patched */ int check_sizes(int model, int rb_packed_size, int rb_unpacked_size, int of_packed_size, int of_unpacked_size, int *total_size, char *errstr, int errstrsize) { /* XXX: we keep the first 0x200 bytes block unmodified, we just replace * the ARM vectors */ unsigned int packed_size = ams_identity[model].bootloader_size + sizeof(nrv2e_d8) + of_packed_size + rb_packed_size + 0x200; /* how much memory is available */ unsigned int memory_size = model_memory_size(model); /* the memory used when unpacking the OF */ unsigned int ram_of = sizeof(nrv2e_d8) + of_packed_size + of_unpacked_size; /* the memory used when unpacking the bootloader */ unsigned int ram_rb = sizeof(nrv2e_d8) + rb_packed_size + rb_unpacked_size; *total_size = packed_size; #define ERROR(format, ...) \ do { \ snprintf(errstr, errstrsize, format, __VA_ARGS__); \ return 0; \ } while(0) /* will packed data fit in the OF file ? */ if(packed_size > of_unpacked_size) ERROR( "[ERR] Packed data (%d bytes) doesn't fit in the firmware " "(%d bytes)\n", packed_size, of_unpacked_size ); else if(ram_rb > memory_size) ERROR("[ERR] Rockbox can't be unpacked at runtime, needs %d bytes " "of memory and only %d available\n", ram_rb, memory_size ); else if(ram_of > memory_size) ERROR("[ERR] OF can't be unpacked at runtime, needs %d bytes " "of memory and only %d available\n", ram_of, memory_size ); return 1; #undef ERROR }