% $Id$ % \section{\label{ref:PlaybackOptions}Playback} The \setting{Playback} sub menu allows you to configure settings related to audio playback. \begin{description} \item[Shuffle]Turning shuffle on will cause Rockbox to randomly re-order the playlist. Thus, to shuffle all of the audio files on the player, you first need to create a playlist containing all of them. For more information on creating playlists refer to \reference{ref:working_with_playlists}.\\ Options: \setting{Yes}/\setting{No}. % \item[Repeat]Configures settings related to repeating of directories or playlists.\\ Options: \setting{Off} / \setting{All} / \setting{One} / \setting{Shuffle} / \setting{A-B}: \begin{description} % \item[Off]The current playlist will not repeat when it is finished. \note{If you have the \setting{Auto-Change Directory} option set to \setting{Yes}, Rockbox will move on to the next directory on your hard drive. If the \setting{Auto-Change Directory} option is set to \setting{No}, playback will stop when the current directory or playlist is finished.} % \item[All]The current playlist will repeat when it is finished. % \item[One]Repeat one track over and over. % \item[Shuffle]When the current playlist has finished playing, it will be shuffled and then repeated. % \item[A-B]Repeats between two user defined points within a track, typically used by musicians when attempting to learn a piece of music. This option is more complicated to use than the others as the \dap\ must first be placed into A-B repeat mode and then the start and end points defined.\\ \opt{RECORDER_PAD,IRIVER_H100_PAD,IRIVER_H300_PAD,IRIVER_H10_PAD,MROBE100_PAD% ,GIGABEAT_PAD,GIGABEAT_S_PAD,SANSA_E200_PAD,SANSA_C200_PAD}{% To set the Start Point (A) press \ActionWpsAbSetAPrevDir{}. Setting the End Point (B) is done accordingly using \ActionWpsAbSetBNextDir{}. To reset the markers press \ActionWpsAbReset{}. }% \opt{ipod,IAUDIO_X5_PAD,ONDIO_PAD,PLAYER_PAD}{% To set the Start Point (A) press \ActionWpsBrowse{}. The following press of \ActionWpsBrowse{} will set the End Point (B), and a third successive \ActionWpsBrowse{} will reset the markers. }% \end{description} \item[Play Selected First]This setting controls what happens when you select a file for playback while shuffle mode is on. If the \setting{Play Selected First} setting is \setting{Yes}, the file you selected will be played first. If this setting is \setting{No}, a random file in the directory will be played first. \item[Fast-Forward/Rewind]These settings control the speed and acceleration during fast forward and rewind. The setting \setting{FF/RW Min Step} controls the initial speed and \setting{FF/RW Accel} controls the acceleration. \item[Anti-Skip Buffer]This setting allows you to control how much music is stored in the \daps{} memory whilst playing a song, acting as a buffer against shock or playback problems. The \dap{} transfers the selected amount of the forthcoming song into its memory at high speed whilst you are playing the song. It keeps a ``rolling'' buffer, which keeps feeding more of the forthcoming song into memory as it goes along. If the \dap{} is knocked, shaken or jogged heavily while Rockbox is trying to read the hard drive, Rockbox might not be able to read the drive. Rockbox will retry over and over again until it succeeds, but may eventually reach the end of the memory buffer. When that happens, Rockbox must stop playing and wait for more data from the disk, which causes your music to skip. The anti-skip setting tells Rockbox how much extra buffer memory to spare to handle this situation. This setting therefore allows you to reduce the chances of there being a gap or pause during playback of songs. \nopt{ondio}{ \opt{MASCODEC}{The anti-skip buffer can be set to a value between 0 and 7 seconds.} }% \opt{ondio}{ The anti-skip buffer can safely be kept at zero. It will eventually be eliminated. }% \opt{swcodec}{The anti-skip buffer can be set to various values between 5 seconds and 10 minutes.}% \note{Having a large anti-skip buffer tends to use more power, and may reduce your battery life. It is recommended to always use the lowest possible setting that allows correct and continuous playback.} \item[Fade on Stop/Pause]Enables and disables a fade effect when you pause or stop playing a song. If the Fade on Stop/Pause option is set to \setting{Yes}, your music will fade out when you stop or pause playback, and fade in when you resume playback. \item[Party Mode]Enables unstoppable music playback. When new songs are selected, they are queued at the end of the current dynamic playlist instead of being played immediately. Pausing and stopping playback is disabled as well as skipping songs and launching plugins. \opt{swcodec}{ \item[Crossfade] This setting enables a cross-fader. At the end of a song, the song will fade out as the next song fades in, creating a smooth transition between songs. The crossfade setting is particularly effective when the player is set on shuffle.\\ Options for crossfade settings are: \begin{description} \item[Enable Crossfade]If set to \setting{Off}, crossfade is disabled. If set to \setting{Always}, songs will always crossfade into one another. If set to \setting{Shuffle}, crossfade is enabled when the shuffle feature is set to \setting{Yes}, but disabled otherwise. If set to track skip only, tracks will only crossfade when you manually change tracks. % \item[Fade In Delay]The ``fade in delay'' is the length of time between when the crossfade process begins and when the new track begins to fade in. % \item[Fade In Duration]The length of time, in seconds, that it takes your music to fade in once the \setting{Fade In Delay} has ended. % \item[Fade Out Delay]The ``fade out delay'' is the length of time between when the crossfade process begins and when the old track begins to fade out. % \item[Fade Out Duration]The length of time, in seconds, that it takes your music to fade out once the \setting{Fade Out Delay} has ended. % \item[Fade Out Mode]If set to \setting{Crossfade}, one song will fade out and the next song will simultaneously fade in. If set to \setting{Mix}, the ending song will continue to play as normal until its end, while the starting song will fade in from under it. \setting{Mix} mode is not used for manual track skips, even if it is selected here. \end{description} \note{The rules above apply except in the instance where \setting{Fade Out Delay} plus \setting{Fade Out Duration} is less then \setting{Fade In Delay} (which would create a gap in the audio). In this case, the \setting{Fade In Delay} is reduced to eliminate the gap.} The graphic below illustrates how the different settings work in practice. \includegraphics[width=14cm]{configure_rockbox/images/crossfade_graphic.png} }% \opt{swcodec}{ \item[Replaygain]This allows you to control the replaygain function. The purpose of replaygain is to adjust the volume of the music played so that all songs (or albums, depending on your settings) have the same apparent volume. This prevents sudden changes in volume when changing between songs recorded at different volume levels. For replaygain to work, the songs must have been processed by a program that adds replaygain information to the ID3 tags (or Vorbis tags). \note{APEv2 tags are not currently supported.} Options for replaygain are: \begin{description} \item[Enable Replaygain]This turns on/off the replaygain function. % \item[Prevent Clipping]Avoid clipping of a song's waveform. If a song would clip during playback, the volume is lowered for that song. Replaygain information is needed for this to work. % \item[Replaygain Type]Choose the type of replaygain to apply: \begin{description} \item[Album Gain]Maintain a constant volume level between albums, but keep any intentional volume variations between songs in an album. (If album gain value is not available, uses track gain information). % \item[Track Gain]Maintain a constant volume level between tracks. If track gain value is not available, no replaygain is applied. % \item[Track Gain If Shuffling]Maintains a constant volume between tracks if \setting{Shuffle} is set to \setting{Yes}. Reverts to album mode if \setting{Shuffle} is set to \setting{No}. \end{description} % \item[Pre-amp]This allows you to adjust the volume when replaygain is applied. Replaygain often lowers the volume, sometimes quite much, so here you can compensate for that. Please note that a (large) positive pre-amp setting can cause clipping, unless prevent clipping is enabled. The pre-amp can be set to any decibel (dB) value between -12dB and +12dB, in increments of 0.1{}dB. \end{description} } \opt{swcodec}{ \item[Beep Volume]Controls the volume of the beep that is heard when skipping forward or backward between tracks. The beep is disabled when set to \setting{Off}. } \opt{spdif_power}{ \item[Optical Output. ]Enables or disables the optical S/PDIF output to allow a digital connection to a suitable external decoder. To enable optical output, set to \setting{Yes} } \item[Auto-Change Directory]Control what Rockbox does when it reaches the end of a directory. If \setting{Auto-Change Directory} is set to \setting{Yes}, Rockbox will continue to the next directory. If \setting{Auto-Change Directory} is set to \setting{No}, playback will stop at the end of the current playlist. Using the \setting{Random} feature requires you to first generate a folder list via the Random Folder Advance Configuration plugin (see \reference{ref:random_folder_advance_config}). \note{You must have the \setting{Repeat} option set to \setting{No} for \setting{Auto-Change Directory} to function properly.} \note{This feature only works when songs have been played from the file browser. Using it with the database may cause unexpected behavior.} % \opt{headphone_detection}{ \item[Pause on Headphone Unplug] Enables and disables automatic pausing of playback when the headphones are disconnected from the \daps{} headphone socket. % \begin{description} \item[Pause on Headphone Unplug]Options for automatic pause: \begin{description} \item[Off.] Disables automatic pause. % \item[Pause.] Pauses the \dap{} when the headphones are removed. % \item[Pause and Resume.] Pauses when the headphones are removed, and resumes playback when they are reconnected. \end{description} \item[Duration to Rewind] Number of seconds (between 0 and 15) to rewind playback when the headphones are removed. % \item[Disable Auto-Resume If Phones Not Present] This option will disable the automatic resumption of playback at startup if the headphones are not connected to the \dap{}. \note{This requires \setting{Resume on Startup} to be enabled.} \end{description} }% \item[Last.fm Log]\index{Last.fm Log}\index{Audioscrobbler|see{Last.fm Log}} Enables logging of your played tracks for submittal to \url{http://www.last.fm}. This service was formely known as \emph{Audioscrobbler}. When you enable this option, you'll have to reboot to start the logging. The log-file is called \opt{rtc}{\fname{.scrobbler.log},}% \nopt{rtc}{\fname{.scrobbler-timeless.log},}% and is to be found in the root directory of your \dap{}. \note{See \wikilink{LastFMLog} for a further description, and for tools you can use to submit your Last.fm log.} \item[Cuesheet Support]\index{Cuesheet Support} Enables reading of cuesheet files for played tracks. If a cuesheet is found for a track, track markers are displayed on the progressbar and it is possible to skip between the tracks within the cuesheet. Also the information found in the cuesheet file will replace the information from the ID3 tags. When you enable this option, you'll have to reboot for it to come into effect. \item[Skip Length]\index{Skip Length} Designed to speed up navigation and prevent unintentional track skipping when listening to long audio tracks, \setting{Skip Length} changes the behavior of the \ActionWpsSkipPrev{} and \ActionWpsSkipNext{} buttons so that they skip by a given number of minutes instead of skipping to a new track. \note{To skip tracks with this setting set to a time interval, press Short \ActionWpsSkipPrev{} + Long \ActionWpsSkipNext{} to go forward and Short \ActionWpsSkipNext{} + Long \ActionWpsSkipPrev{} to go back.} \end{description}