/***************************************************************************
 *             __________               __   ___.
 *   Open      \______   \ ____   ____ |  | _\_ |__   _______  ___
 *   Source     |       _//  _ \_/ ___\|  |/ /| __ \ /  _ \  \/  /
 *   Jukebox    |    |   (  <_> )  \___|    < | \_\ (  <_> > <  <
 *   Firmware   |____|_  /\____/ \___  >__|_ \|___  /\____/__/\_ \
 *                     \/            \/     \/    \/            \/
 * $Id$
 *
 * Copyright (C) 2002 by Alan Korr
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version 2
 * of the License, or (at your option) any later version.
 *
 * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
 * KIND, either express or implied.
 *
 ****************************************************************************/
#include "system.h"
#include "thread.h"
#include "i2s.h"
#include "i2c-pp.h"
#include "as3514.h"
#ifdef HAVE_HOTSWAP
#include "sd-pp-target.h"
#endif
#include "button-target.h"
#include "usb-target.h"
#include "usb_drv.h"
#ifdef HAVE_REMOTE_LCD
#include "lcd-remote-target.h"
#endif

#if !defined(BOOTLOADER) || defined(HAVE_BOOTLOADER_USB_MODE)
extern void TIMER1(void);
extern void TIMER2(void);
extern void SERIAL0(void);

#if defined(HAVE_ADJUSTABLE_CPU_FREQ) && (NUM_CORES > 1)
static struct corelock cpufreq_cl SHAREDBSS_ATTR;
#endif

#if defined(IPOD_VIDEO) && !defined(BOOTLOADER)
unsigned char probed_ramsize;
#endif

void __attribute__((interrupt("IRQ"))) irq_handler(void)
{
    if(CURRENT_CORE == CPU)
    {
        if (CPU_INT_STAT & TIMER1_MASK) {
            TIMER1();
        }
        else if (CPU_INT_STAT & TIMER2_MASK) {
            TIMER2();
        }
#ifdef HAVE_USBSTACK
        /* Rather high priority - place near front */
        else if (CPU_INT_STAT & USB_MASK) {
            usb_drv_int();
        }
#endif
#if defined(IPOD_MINI) /* Mini 1st gen only, mini 2nd gen uses iPod 4G code */
        else if (CPU_HI_INT_STAT & GPIO0_MASK) {
            if ((GPIOA_INT_STAT & 0x3f) || (GPIOB_INT_STAT & 0x30))
                ipod_mini_button_int();
            if (GPIOC_INT_STAT & 0x02)
                firewire_insert_int();
            if (GPIOD_INT_STAT & 0x08)
                usb_insert_int();
        }
/* end IPOD_MINI */
#elif CONFIG_KEYPAD == IPOD_4G_PAD /* except Mini 1st gen, handled above */
        else if (CPU_HI_INT_STAT & I2C_MASK) {
            ipod_4g_button_int();
        }
#if defined(IPOD_COLOR) || defined(IPOD_MINI2G) || defined(IPOD_4G)
        else if (CPU_HI_INT_STAT & GPIO0_MASK) {
            if (GPIOC_INT_STAT & 0x02)
                firewire_insert_int();
            if (GPIOD_INT_STAT & 0x08)
                usb_insert_int();
        }
#elif defined(IPOD_NANO) || defined(IPOD_VIDEO)
        else if (CPU_HI_INT_STAT & GPIO2_MASK) {
            if (GPIOL_INT_STAT & 0x10)
                usb_insert_int();
        }
#endif
/* end CONFIG_KEYPAD == IPOD_4G_PAD */
#elif defined(IRIVER_H10) || defined(IRIVER_H10_5GB)
        else if (CPU_HI_INT_STAT & GPIO2_MASK) {
            if (GPIOL_INT_STAT & 0x04)
                usb_insert_int();
        }
/* end IRIVER_H10 || IRIVER_H10_5GB */
#elif defined(SANSA_E200)
        else if (CPU_HI_INT_STAT & GPIO0_MASK) {
#ifdef HAVE_HOTSWAP
            if (GPIOA_INT_STAT & 0x80)
                microsd_int();
#endif
            if (GPIOB_INT_STAT & 0x10)
                usb_insert_int();
        }
        else if (CPU_HI_INT_STAT & GPIO1_MASK) {
            if (GPIOF_INT_STAT & 0xff)
                button_int();
            if (GPIOH_INT_STAT & 0xc0)
                clickwheel_int();
        }
/* end SANSA_E200 */
#elif defined(SANSA_C200)
        else if (CPU_HI_INT_STAT & GPIO1_MASK) {
            if (GPIOH_INT_STAT & 0x02)
                usb_insert_int();
        }
#ifdef HAVE_HOTSWAP
        else if (CPU_HI_INT_STAT & GPIO2_MASK) {
            if (GPIOL_INT_STAT & 0x08)
                microsd_int();
        }
#endif
/* end SANSA_C200 */
#elif defined(MROBE_100)
        else if (CPU_HI_INT_STAT & GPIO0_MASK) {
            if (GPIOD_INT_STAT & 0x02)
                button_int();
            if (GPIOD_INT_STAT & 0x80)
                headphones_int();

        }
        else if (CPU_HI_INT_STAT & GPIO2_MASK) {
            if (GPIOL_INT_STAT & 0x04)
                usb_insert_int();
        }
/* end MROBE_100 */
#elif defined(PHILIPS_SA9200)
        else if (CPU_HI_INT_STAT & GPIO0_MASK) {
            if (GPIOD_INT_STAT & 0x02)
                button_int();
            if (GPIOB_INT_STAT & 0x40)
                usb_insert_int();
        }
/* end PHILIPS_SA9200 */
#elif defined(PHILIPS_HDD1630) || defined(PHILIPS_HDD6330)
        else if (CPU_HI_INT_STAT & GPIO0_MASK) {
            if (GPIOA_INT_STAT & 0x20)
                button_int();
        }
        else if (CPU_HI_INT_STAT & GPIO1_MASK) {
            if (GPIOE_INT_STAT & 0x04)
                usb_insert_int();
        }
/* end PHILIPS_HDD1630 || PHILIPS_HDD6330 */
#elif defined(SAMSUNG_YH820) || defined(SAMSUNG_YH920) || defined(SAMSUNG_YH925)
        else if (CPU_HI_INT_STAT & GPIO0_MASK) {
            if (GPIOD_INT_STAT & 0x10)
                usb_insert_int();
        }
/* end SAMSUNG_YHxxx */
#elif defined(PBELL_VIBE500)
        else if (CPU_HI_INT_STAT & GPIO0_MASK) {
            if (GPIOA_INT_STAT & 0x20)
                button_int();
        }
        else if (CPU_HI_INT_STAT & GPIO2_MASK) {
            if (GPIOL_INT_STAT & 0x04)
                usb_insert_int();
        }
/* end PBELL_VIBE500 */
#endif
#ifdef IPOD_ACCESSORY_PROTOCOL
        else if (CPU_HI_INT_STAT & SER0_MASK) {
            SERIAL0();
        }
#endif
    } else {
        if (COP_INT_STAT & TIMER2_MASK)
            TIMER2();
    }
}
#endif /* BOOTLOADER || HAVE_BOOTLOADER_USB_MODE */

#if !defined(BOOTLOADER) || defined(HAVE_BOOTLOADER_USB_MODE)
static void disable_all_interrupts(void)
{
    COP_HI_INT_DIS      = -1;
    CPU_HI_INT_DIS      = -1;
    HI_INT_FORCED_CLR   = -1;

    COP_INT_DIS         = -1;
    CPU_INT_DIS         = -1;
    INT_FORCED_CLR      = -1;

    GPIOA_INT_EN        = 0;
    GPIOB_INT_EN        = 0;
    GPIOC_INT_EN        = 0;
    GPIOD_INT_EN        = 0;
    GPIOE_INT_EN        = 0;
    GPIOF_INT_EN        = 0;
    GPIOG_INT_EN        = 0;
    GPIOH_INT_EN        = 0;
    GPIOI_INT_EN        = 0;
    GPIOJ_INT_EN        = 0;
    GPIOK_INT_EN        = 0;
    GPIOL_INT_EN        = 0;
}

void ICODE_ATTR cpucache_commit(void)
{
    if (CACHE_CTL & CACHE_CTL_ENABLE)
    {
        CACHE_OPERATION |= CACHE_OP_FLUSH;
        while ((CACHE_CTL & CACHE_CTL_BUSY) != 0);
        nop; nop; nop; nop;
    }
}
void cpucache_flush(void) __attribute__((alias("cpucache_commit")));

void ICODE_ATTR cpucache_commit_discard(void)
{
    if (CACHE_CTL & CACHE_CTL_ENABLE)
    {
        CACHE_OPERATION |= CACHE_OP_FLUSH | CACHE_OP_INVALIDATE;
        while ((CACHE_CTL & CACHE_CTL_BUSY) != 0);
        nop; nop; nop; nop;
    }
}
void cpucache_invalidate(void) __attribute__((alias("cpucache_commit_discard")));

static void init_cache(void)
{
/* Initialising the cache in the iPod bootloader may prevent Rockbox from starting
 * depending on the model */

    /* cache init mode */
    CACHE_CTL &= ~(CACHE_CTL_ENABLE | CACHE_CTL_RUN);
    CACHE_CTL |= CACHE_CTL_INIT;

#ifndef BOOTLOADER
    /* what's this do? */
    CACHE_PRIORITY |= CURRENT_CORE == CPU ? 0x10 : 0x20;
#endif

    /* Cache if (addr & mask) >> 16 == (mask & match) >> 16:
     * yes: 0x00000000 - 0x03ffffff
     *  no: 0x04000000 - 0x1fffffff
     * yes: 0x20000000 - 0x23ffffff
     *  no: 0x24000000 - 0x3fffffff
     */
    CACHE_MASK = 0x00001c00;
    CACHE_OPERATION = 0xfc0;

    /* enable cache */
    CACHE_CTL |= CACHE_CTL_INIT | CACHE_CTL_ENABLE | CACHE_CTL_RUN;
    nop; nop; nop; nop;
}
#endif /* BOOTLOADER || HAVE_BOOTLOADER_USB_MODE */

/* We need this for Sansas since we boost the cpu in their bootloader */
#if !defined(BOOTLOADER) || (defined(SANSA_E200) || defined(SANSA_C200) || \
    defined(PHILIPS_SA9200))
void scale_suspend_core(bool suspend) ICODE_ATTR;
void scale_suspend_core(bool suspend)
{
    unsigned int core = CURRENT_CORE;
    IF_COP( unsigned int othercore = 1 - core; )
    static int oldstatus IBSS_ATTR;

    if (suspend)
    {
        oldstatus = disable_interrupt_save(IRQ_FIQ_STATUS);
        IF_COP( PROC_CTL(othercore) = 0x40000000; nop; )
        PROC_CTL(core) = 0x48000003; nop;
    }
    else
    {
        PROC_CTL(core) = 0x4800001f; nop;
        IF_COP( PROC_CTL(othercore) = 0x00000000; nop; )
        restore_interrupt(oldstatus);
    }
}

#ifdef HAVE_ADJUSTABLE_CPU_FREQ
void set_cpu_frequency(long frequency) ICODE_ATTR;
void set_cpu_frequency(long frequency)
#else
static void pp_set_cpu_frequency(long frequency)
#endif
{      
#if defined(HAVE_ADJUSTABLE_CPU_FREQ) && (NUM_CORES > 1)
    corelock_lock(&cpufreq_cl);
#endif

    switch (frequency)
    {
      /* Note1: The PP5022 PLL must be run at >= 96MHz
       * Bits 20..21 select the post divider (1/2/4/8).
       * PP5026 is similar to PP5022 except it doesn't
       * have this limitation (and the post divider?) 
       * Note2: CLOCK_SOURCE is set via 0=32kHz, 1=16MHz,
       * 2=24MHz, 3=33MHz, 4=48MHz, 5=SLOW, 6=FAST, 7=PLL. 
       * SLOW = 24MHz / (DIV_SLOW + 1), DIV = Bits 16-19
       * FAST = PLL   / (DIV_FAST + 1), DIV = Bits 20-23 */
      case CPUFREQ_SLEEP:
        cpu_frequency =  CPUFREQ_SLEEP;
        PLL_CONTROL  |=  0x0c000000;
        scale_suspend_core(true);
        CLOCK_SOURCE  =  0x20000000; /* source #1, #2, #3, #4: 32kHz (#2 active) */
        scale_suspend_core(false);
        PLL_CONTROL  &= ~0x80000000; /* disable PLL */
        DEV_INIT2    &= ~INIT_PLL;   /* disable PLL power */
        break;
        
      case CPUFREQ_MAX:
        cpu_frequency = CPUFREQ_MAX;
        DEV_INIT2    |= INIT_PLL;   /* enable PLL power */
        PLL_CONTROL  |= 0x88000000; /* enable PLL */
        scale_suspend_core(true);
        CLOCK_SOURCE  = 0x20002222; /* source #1, #2, #3, #4: 24MHz (#2 active) */
        DEV_TIMING1   = 0x00000303;
        scale_suspend_core(false);
#if   defined(IPOD_MINI2G)
        MLCD_SCLK_DIV = 0x00000001; /* Mono LCD bridge serial clock divider */
#elif defined(IPOD_NANO)
        IDE0_CFG     |= 0x10000000; /* set ">65MHz" bit */
#endif
#if CONFIG_CPU == PP5020
        PLL_CONTROL   = 0x8a020a03; /* 80 MHz = 10/3 * 24MHz */
        PLL_STATUS    = 0xd19b;     /* unlock frequencies > 66MHz */
        PLL_CONTROL   = 0x8a020a03; /* repeat setup */
        udelay(500);                /* wait for relock */
#elif (CONFIG_CPU == PP5022) || (CONFIG_CPU == PP5024)
        PLL_CONTROL   = 0x8a121403; /*  80 MHz = (20/3 * 24MHz) / 2 */
        while (!(PLL_STATUS & 0x80000000)); /* wait for relock */
#endif
        scale_suspend_core(true);
        DEV_TIMING1   = 0x00000808;
        CLOCK_SOURCE  = 0x20007777; /* source #1, #2, #3, #4: PLL (#2 active) */
        scale_suspend_core(false);
        break;
#if 0 /******** CPUFREQ_NORMAL = 24MHz without PLL ********/
      case CPUFREQ_NORMAL:
        cpu_frequency =  CPUFREQ_NORMAL;
        PLL_CONTROL  |=  0x08000000;
        scale_suspend_core(true);
        CLOCK_SOURCE  =  0x20002222; /* source #1, #2, #3, #4: 24MHz (#2 active) */
        DEV_TIMING1   =  0x00000303;
#if   defined(IPOD_MINI2G)
        MLCD_SCLK_DIV =  0x00000000; /* Mono LCD bridge serial clock divider */
#elif defined(IPOD_NANO)
        IDE0_CFG     &= ~0x10000000; /* clear ">65MHz" bit */
#endif
        scale_suspend_core(false);
        PLL_CONTROL  &= ~0x80000000; /* disable PLL */
        DEV_INIT2    &= ~INIT_PLL;   /* disable PLL power */
        break;
#else /******** CPUFREQ_NORMAL = 30MHz with PLL ********/
    case CPUFREQ_NORMAL:
        cpu_frequency = CPUFREQ_NORMAL;
        DEV_INIT2    |= INIT_PLL;   /* enable PLL power */
        PLL_CONTROL  |= 0x88000000; /* enable PLL */
        scale_suspend_core(true);
        CLOCK_SOURCE  = 0x20002222; /* source #1, #2, #3, #4: 24MHz (#2 active) */
        DEV_TIMING1   = 0x00000303;
        scale_suspend_core(false);
#if   defined(IPOD_MINI2G)
        MLCD_SCLK_DIV =  0x00000000; /* Mono LCD bridge serial clock divider */
#elif defined(IPOD_NANO)
        IDE0_CFG     &= ~0x10000000; /* clear ">65MHz" bit */
#endif
#if CONFIG_CPU == PP5020
        PLL_CONTROL   = 0x8a020504; /* 30 MHz = 5/4 * 24MHz */
        udelay(500);                /* wait for relock */
#elif (CONFIG_CPU == PP5022) || (CONFIG_CPU == PP5024)
        PLL_CONTROL   = 0x8a220501; /* 30 MHz = (5/1 * 24MHz) / 4 */
        while (!(PLL_STATUS & 0x80000000)); /* wait for relock */
#endif
        scale_suspend_core(true);
        DEV_TIMING1   = 0x00000303;
        CLOCK_SOURCE  = 0x20007777; /* source #1, #2, #3, #4: PLL (#2 active) */
        scale_suspend_core(false);
        break;
#endif /******** CPUFREQ_NORMAL end ********/
      default:
        cpu_frequency =  CPUFREQ_DEFAULT;
        PLL_CONTROL  |=  0x08000000;
        scale_suspend_core(true);
        CLOCK_SOURCE  =  0x20002222; /* source #1, #2, #3, #4: 24MHz (#2 active) */
        DEV_TIMING1   =  0x00000303;
#if   defined(IPOD_MINI2G)
        MLCD_SCLK_DIV =  0x00000000; /* Mono LCD bridge serial clock divider */
#elif defined(IPOD_NANO)
        IDE0_CFG     &= ~0x10000000; /* clear ">65MHz" bit */
#endif
        scale_suspend_core(false);
        PLL_CONTROL  &= ~0x80000000; /* disable PLL */
        DEV_INIT2    &= ~INIT_PLL;   /* disable PLL power */
        break;
    }
    
#if defined(HAVE_ADJUSTABLE_CPU_FREQ) && (NUM_CORES > 1)
    corelock_unlock(&cpufreq_cl);
#endif
}
#endif /* !BOOTLOADER || (SANSA_E200 || SANSA_C200 || PHILIPS_SA9200) */

#ifndef BOOTLOADER
void system_init(void)
{
    if (CURRENT_CORE == CPU)
    {
#if defined (IRIVER_H10) || defined(IRIVER_H10_5GB) || defined(IPOD_COLOR)
        /* set minimum startup configuration */
        DEV_EN         = 0xc2000124;
        DEV_EN2        = 0x00002000;
        CACHE_PRIORITY = 0x0000003f;
        GPO32_VAL      = 0x20000000;
        DEV_INIT1      = 0xdc000000;
        DEV_INIT2      = 0x40000000;

        /* reset all allowed devices */
        DEV_RS         = 0x3dfffef8;
        DEV_RS2        = 0xffffdfff;
        DEV_RS         = 0x00000000;
        DEV_RS2        = 0x00000000;
#elif defined (IPOD_VIDEO)    
        /* set minimum startup configuration */
        DEV_EN         = 0xc2000124;
        DEV_EN2        = 0x00000000;
        CACHE_PRIORITY = 0x0000003f;
        GPO32_VAL     &= 0x00004000;
        DEV_INIT1      = 0x00000000;
        DEV_INIT2      = 0x40000000;

        /* reset all allowed devices */
        DEV_RS         = 0x3dfffef8;
        DEV_RS2        = 0xffffffff;
        DEV_RS         = 0x00000000;
        DEV_RS2        = 0x00000000;
#elif defined (IPOD_NANO)    
        /* set minimum startup configuration */
        DEV_EN         = 0xc2000124;
        DEV_EN2        = 0x00002000;
        CACHE_PRIORITY = 0x0000003f;
        GPO32_VAL      = 0x50000000;
        DEV_INIT1      = 0xa8000000;
        DEV_INIT2      = 0x40000000;

        /* reset all allowed devices */
        DEV_RS         = 0x3ffffef8;
        DEV_RS2        = 0xffffdfff;
        DEV_RS         = 0x00000000;
        DEV_RS2        = 0x00000000;
#elif defined(SANSA_C200) || defined (SANSA_E200)
        /* set minimum startup configuration */
        DEV_EN         = 0xc4000124;
        DEV_EN2        = 0x00000000;
        CACHE_PRIORITY = 0x0000003f;
        GPO32_VAL      = 0x10000000;
        DEV_INIT1      = 0x54000000;
        DEV_INIT2      = 0x40000000;

        /* reset all allowed devices */
        DEV_RS         = 0x3bfffef8;
        DEV_RS2        = 0xffffffff;
        DEV_RS         = 0x00000000;
        DEV_RS2        = 0x00000000;
#elif defined(PHILIPS_SA9200)
        /* reset all allowed devices */
        DEV_RS         = 0x3ffffef8;
        DEV_RS2        = 0xffffffff;
        DEV_RS         = 0x00000000;
        DEV_RS2        = 0x00000000;
#elif defined(IPOD_4G)
        /* set minimum startup configuration */
        DEV_EN         = 0xc2020124;
        DEV_EN2        = 0x00000000;
        CACHE_PRIORITY = 0x0000003f;
        GPO32_VAL      = 0x02000000;
        DEV_INIT1      = 0x00000000;
        DEV_INIT2      = 0x40000000;

        /* reset all allowed devices */
        DEV_RS         = 0x3dfdfef8;
        DEV_RS2        = 0xffffffff;
        DEV_RS         = 0x00000000;
        DEV_RS2        = 0x00000000;
#elif defined (IPOD_MINI)
        /* to be done */
#elif defined (IPOD_MINI2G)
        /* to be done */
#elif defined (MROBE_100)
        /* to be done */
#elif defined (TATUNG_TPJ1022)
        /* to be done */
#elif defined(PBELL_VIBE500)
        /* reset all allowed devices */
        DEV_RS         = 0x3ffffef8;
        DEV_RS2        = 0xffffffff;
        DEV_RS         = 0x00000000;
        DEV_RS2        = 0x00000000;
#endif

#if !defined(SANSA_E200) && !defined(SANSA_C200) && !defined(PHILIPS_SA9200)
        /* Remap the flash ROM on CPU, keep hidden from COP:
         * 0x00000000-0x3fffffff = 0x20000000-0x23ffffff */
        MMAP1_LOGICAL  = 0x20003c00;
        MMAP1_PHYSICAL = 0x00003084 |
            MMAP_PHYS_READ_MASK | MMAP_PHYS_WRITE_MASK |
            MMAP_PHYS_DATA_MASK | MMAP_PHYS_CODE_MASK;
#endif

        disable_all_interrupts();

#ifdef HAVE_ADJUSTABLE_CPU_FREQ
#if NUM_CORES > 1
        corelock_init(&cpufreq_cl);
        cpu_boost_init();
#endif
#else
        pp_set_cpu_frequency(CPUFREQ_MAX);
#endif

#if defined(IPOD_VIDEO)
        /* crt0-pp.S wrote the ram size to the last byte of the first 32MB
           ram bank. See the comment there for how we determine it. */
        volatile unsigned char *end32 = (volatile unsigned char *)0x01ffffff;
        probed_ramsize = *end32;
#endif
    }

    init_cache();
}

#else /* BOOTLOADER */

void system_init(void)
{
    /* Only the CPU gets here in the bootloader */
#ifdef HAVE_BOOTLOADER_USB_MODE
    disable_all_interrupts();
    init_cache();
    /* Use the local vector map */
    CACHE_CTL |= CACHE_CTL_VECT_REMAP;
#endif /* HAVE_BOOTLOADER_USB_MODE */

#if defined(SANSA_C200) || defined(SANSA_E200) || defined(PHILIPS_SA9200)
        pp_set_cpu_frequency(CPUFREQ_MAX);
#endif
    /* Else the frequency should get changed upon USB connect -
     * decide per-target */
}

#ifdef HAVE_BOOTLOADER_USB_MODE
void system_prepare_fw_start(void)
{
    disable_interrupt(IRQ_FIQ_STATUS);
    tick_stop();
    disable_all_interrupts();
    /* Some OF's disable this themselves, others do not and will hang. */
    CACHE_CTL &= ~CACHE_CTL_VECT_REMAP;
}
#endif /* HAVE_BOOTLOADER_USB_MODE */
#endif /* !BOOTLOADER */

void ICODE_ATTR system_reboot(void)
{
    disable_interrupt(IRQ_FIQ_STATUS);
    CPU_INT_DIS = -1;
    COP_INT_DIS = -1;

    /* Reboot */
#if defined(SANSA_E200) || defined(SANSA_C200) || defined(PHILIPS_SA9200)
    CACHE_CTL &= ~CACHE_CTL_VECT_REMAP;

    /* Magic used by the c200 OF: 0x23066000
       Magic used by the c200 BL: 0x23066b7b
       In both cases, the OF executes these 2 commands from iram. */
    STRAP_OPT_A = 0x23066b7b;
    DEV_RS = DEV_SYSTEM;
#else
    DEV_RS |= DEV_SYSTEM;
#endif
    /* wait until reboot kicks in */
    while (1);
}

void system_exception_wait(void)
{
    /* FIXME: we just need the right buttons */
    CPU_INT_DIS = -1;
    COP_INT_DIS = -1;

    /* Halt */
    PROC_CTL(CURRENT_CORE) = 0x40000000;
    while (1);
}

int system_memory_guard(int newmode)
{
    (void)newmode;
    return 0;
}