/* * This config file is for the Sandisk Sansa Clip+ */ /* For Rolo and boot loader */ #define MODEL_NUMBER 66 #define MODEL_NAME "Sandisk Sansa Clip+" #define FIRMWARE_OFFSET_FILE_DATA 8 #define FIRMWARE_OFFSET_FILE_CRC 0 #ifndef BOOTLOADER #define HAVE_MULTIDRIVE #define NUM_DRIVES 2 #define HAVE_HOTSWAP #endif #define HW_SAMPR_CAPS SAMPR_CAP_ALL /* define this if you have recording possibility */ #define HAVE_RECORDING #define REC_SAMPR_CAPS (SAMPR_CAP_48 | SAMPR_CAP_44 | SAMPR_CAP_32 | \ SAMPR_CAP_24 | SAMPR_CAP_22 | SAMPR_CAP_16 | \ SAMPR_CAP_12 | SAMPR_CAP_11 | SAMPR_CAP_8) /* because the samplerates don't match at each point, we must be able to * tell PCM which set of rates to use. not needed if recording rates are * a simple subset of playback rates and are equal values. */ #define CONFIG_SAMPR_TYPES /* Define bitmask of input sources - recordable bitmask can be defined explicitly if different */ #define INPUT_SRC_CAPS (SRC_CAP_MIC | SRC_CAP_FMRADIO) /* define this if you have a bitmap LCD display */ #define HAVE_LCD_BITMAP /* define this if you have access to the quickscreen */ #define HAVE_QUICKSCREEN /* define this if you would like tagcache to build on this target */ #define HAVE_TAGCACHE /* LCD dimensions */ #define LCD_WIDTH 128 #define LCD_HEIGHT 64 #define LCD_DEPTH 1 #define LCD_PIXELFORMAT VERTICAL_PACKING #define HAVE_NEGATIVE_LCD /* bright on dark */ #define HAVE_LCD_SPLIT /* split display */ /* Display colours, for screenshots and sim (0xRRGGBB) */ #define LCD_DARKCOLOR 0x000000 #define LCD_BRIGHTCOLOR 0x000000 #define LCD_BL_DARKCOLOR 0x000000 #define LCD_BL_BRIGHTCOLOR 0x0de2e5 #define LCD_DARKCOLOR_2 0x000000 #define LCD_BRIGHTCOLOR_2 0x000000 #define LCD_BL_DARKCOLOR_2 0x000000 #define LCD_BL_BRIGHTCOLOR_2 0xffe60f #define LCD_SPLIT_POS 16 #define LCD_SPLIT_LINES 2 /* define this if you have LCD enable function */ #define HAVE_LCD_ENABLE #ifndef BOOTLOADER /* Define this if your LCD can be put to sleep. * HAVE_LCD_ENABLE should be defined as well. */ //#define HAVE_LCD_SLEEP //#define HAVE_LCD_SLEEP_SETTING #endif /* define this if you can flip your LCD */ #define HAVE_LCD_FLIP /* define this if you can invert the pixels */ #define HAVE_LCD_INVERT /* Define this if your LCD can set contrast */ #define HAVE_LCD_CONTRAST #define MIN_CONTRAST_SETTING 0 #define MAX_CONTRAST_SETTING 50 #define DEFAULT_CONTRAST_SETTING 30 #define IRAM_LCDFRAMEBUFFER IDATA_ATTR /* put the lcd frame buffer in IRAM */ #define CONFIG_KEYPAD SANSA_CLIP_PAD /* define this if the target has volume keys which can be used in the lists */ #define HAVE_VOLUME_IN_LIST /* Define this if you do software codec */ #define CONFIG_CODEC SWCODEC /* There is no hardware tone control */ #define HAVE_SW_TONE_CONTROLS /* AS3514 or newer */ #define HAVE_AS3514 #define HAVE_AS3543 #ifndef BOOTLOADER /* define this if you have a real-time clock */ #define CONFIG_RTC RTC_AS3514 /* Define if the device can wake from an RTC alarm */ #define HAVE_RTC_ALARM #endif /* Define this if you have a software controlled poweroff */ #define HAVE_SW_POWEROFF #define HAVE_FAT16SUPPORT /* The number of bytes reserved for loadable codecs */ #define CODEC_SIZE (0x100000-0x8000) /* The number of bytes reserved for loadable plugins */ #define PLUGIN_BUFFER_SIZE 0x80000 #define AB_REPEAT_ENABLE /* FM Tuner */ #define CONFIG_TUNER (SI4700|RDA5802) /* in fact SI4702 */ //#define HAVE_TUNER_PWR_CTRL /* Define this for LCD backlight available */ #define HAVE_BACKLIGHT /* define this if you have a flash memory storage */ #define HAVE_FLASH_STORAGE /* define this if the flash memory uses the SecureDigital Memory Card protocol */ #define CONFIG_STORAGE STORAGE_SD #define BATTERY_CAPACITY_DEFAULT 290 /* default battery capacity */ #define BATTERY_CAPACITY_MIN 290 /* min. capacity selectable */ #define BATTERY_CAPACITY_MAX 290 /* max. capacity selectable */ #define BATTERY_CAPACITY_INC 0 /* capacity increment */ #define BATTERY_TYPES_COUNT 1 /* only one type */ #define CONFIG_BATTERY_MEASURE VOLTAGE_MEASURE /* Charging implemented in a target-specific algorithm */ #define CONFIG_CHARGING CHARGING_TARGET /* define this if the unit can be powered or charged via USB */ #define HAVE_USB_POWER /** Non-simulator section **/ #ifndef SIMULATOR /* Define this if you have a AMS AS3525v2 SoC */ #define CONFIG_CPU AS3525v2 /* Define this if you want to use the AS3525 i2c interface */ #define CONFIG_I2C I2C_AS3525 /* define this if the hardware can be powered off while charging */ /* Sansa can't be powered off while charging */ /* #define HAVE_POWEROFF_WHILE_CHARGING */ /* define current usage levels (based on battery bench) */ #define CURRENT_NORMAL 19 #define CURRENT_BACKLIGHT 15 #define CURRENT_RECORD CURRENT_NORMAL /* TODO */ /* maximum charging current */ #define CURRENT_MAX_CHG 150 /* Define this to the CPU frequency */ #define CPU_FREQ 240000000 /* Type of LCD */ #define CONFIG_LCD LCD_SSD1303 /* USB On-the-go */ #define CONFIG_USBOTG USBOTG_S3C6400X /* enable these for the experimental usb stack */ #define HAVE_USBSTACK #define USE_ROCKBOX_USB #define USB_VENDOR_ID 0x0781 #define USB_PRODUCT_ID 0x74d1 /* Virtual LED (icon) */ #define CONFIG_LED LED_VIRTUAL /* Define this if you have adjustable CPU frequency */ //#define HAVE_ADJUSTABLE_CPU_FREQ #define BOOTFILE_EXT "sansa" #define BOOTFILE "rockbox." BOOTFILE_EXT #define BOOTDIR "/.rockbox" #define ICODE_ATTR_TREMOR_NOT_MDCT #define INCLUDE_TIMEOUT_API #endif /* SIMULATOR */ /** Port-specific settings **/ /* Main LCD backlight brightness range and defaults */ #define MIN_BRIGHTNESS_SETTING 1 #define MAX_BRIGHTNESS_SETTING 12 #define DEFAULT_BRIGHTNESS_SETTING 6 /* Default recording levels */ #define DEFAULT_REC_MIC_GAIN 23 #define DEFAULT_REC_LEFT_GAIN 23 #define DEFAULT_REC_RIGHT_GAIN 23 /* Define this if a programmable hotkey is mapped */ //#define HAVE_HOTKEY