/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * Tuner driver for the Sanyo LV24020LP * * Copyright (C) 2007 Ivan Zupan * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ #include #include #include "config.h" #include "thread.h" #include "kernel.h" #include "tuner.h" /* tuner abstraction interface */ #include "power.h" #include "fmradio.h" /* physical interface driver */ #include "sound.h" #include "pp5024.h" #include "system.h" #ifndef BOOTLOADER static struct mutex tuner_mtx; #if 0 /* define to enable tuner logging */ #define SANYO_TUNER_LOG #endif #ifdef SANYO_TUNER_LOG #include "sprintf.h" #include "file.h" static int fd_log = -1; #define TUNER_LOG_OPEN() if (fd_log < 0) \ fd_log = creat("/tuner_dump.txt") /* syncing required because close() is never called */ #define TUNER_LOG_SYNC() fsync(fd_log) #define TUNER_LOG(s...) fdprintf(fd_log, s) #else #define TUNER_LOG_OPEN() #define TUNER_LOG_SYNC() #define TUNER_LOG(s...) #endif /* SANYO_TUNER_LOG */ /** tuner register defines **/ #if defined(SANSA_E200) || defined(SANSA_C200) #define GPIO_OUTPUT_EN GPIOH_OUTPUT_EN #define GPIO_OUTPUT_VAL GPIOH_OUTPUT_VAL #define GPIO_INPUT_VAL GPIOH_INPUT_VAL #define FM_NRW_PIN 3 #define FM_CLOCK_PIN 4 #define FM_DATA_PIN 5 #elif defined(IAUDIO_7) #define GPIO_OUTPUT_EN GPIOA_DIR #define GPIO_OUTPUT_VAL GPIOA #define GPIO_INPUT_VAL GPIOA #define FM_CLOCK_PIN 5 #define FM_DATA_PIN 6 #define FM_NRW_PIN 7 //#define udelay(x) /* Remove hack when D2 has udelay */ static void udelay(int usecs) { while (usecs--) asm("nop;nop;"); } #elif defined(COWON_D2) #define GPIO_OUTPUT_EN GPIOC_DIR #define GPIO_OUTPUT_VAL GPIOC #define GPIO_INPUT_VAL GPIOC #define FM_NRW_PIN 31 #define FM_CLOCK_PIN 29 #define FM_DATA_PIN 30 #define udelay(x) /* Remove hack when D2 has udelay */ #else #error GPIOs undefined for this target #endif #define FM_CLK_DELAY 1 /* block 1 registers */ /* R */ #define CHIP_ID 0x00 /* W */ #define BLK_SEL 0x01 #define BLK1 0x01 #define BLK2 0x02 /* W */ #define MSRC_SEL 0x02 #define MSR_O (1 << 7) #define AFC_LVL (1 << 6) #define AFC_SPD (1 << 5) #define MSS_SD (1 << 2) #define MSS_FM (1 << 1) #define MSS_IF (1 << 0) /* W */ #define FM_OSC 0x03 /* W */ #define SD_OSC 0x04 /* W */ #define IF_OSC 0x05 /* W */ #define CNT_CTRL 0x06 #define CNT1_CLR (1 << 7) #define CTAB(x) ((x) & (0x7 << 4)) #define CTAB_STOP_2 (0x0 << 4) #define CTAB_STOP_8 (0x1 << 4) #define CTAB_STOP_32 (0x2 << 4) #define CTAB_STOP_128 (0x3 << 4) #define CTAB_STOP_512 (0x4 << 4) #define CTAB_STOP_2048 (0x5 << 4) #define CTAB_STOP_8192 (0x6 << 4) #define CTAB_STOP_32768 (0x7 << 4) #define SWP_CNT_L (1 << 3) #define CNT_EN (1 << 2) #define CNT_SEL (1 << 1) #define CNT_SET (1 << 0) /* W */ #define IRQ_MSK 0x08 #define IM_MS (1 << 6) #define IRQ_LVL (1 << 3) #define IM_AFC (1 << 2) #define IM_FS (1 << 1) #define IM_CNT2 (1 << 0) /* W */ #define FM_CAP 0x09 /* R */ #define CNT_L 0x0a /* Counter register low value */ /* R */ #define CNT_H 0x0b /* Counter register high value */ /* R */ #define CTRL_STAT 0x0c #define AFC_FLG (1 << 0) /* R */ #define RADIO_STAT 0x0d #define RSS_MS (1 << 7) #define RSS_FS(x) ((x) & 0x7f) #define RSS_FS_GET(x) ((x) & 0x7f) #define RSS_FS_SET(x) (x) /* Note: Reading this register will clear field strength and mono/stereo interrupt. */ /* R */ #define IRQ_ID 0x0e #define II_CNT2 (1 << 5) #define II_AFC (1 << 3) #define II_FS_MS (1 << 0) /* W */ #define IRQ_OUT 0x0f /* block 2 registers - offset added in order to id and avoid manual switching */ #define BLK2_START 0x10 /* W */ #define RADIO_CTRL1 (0x02 + BLK2_START) #define EN_MEAS (1 << 7) #define EN_AFC (1 << 6) #define DIR_AFC (1 << 3) #define RST_AFC (1 << 2) /* W */ #define IF_CENTER (0x03 + BLK2_START) /* W */ #define IF_BW (0x05 + BLK2_START) /* W */ #define RADIO_CTRL2 (0x06 + BLK2_START) #define VREF2 (1 << 7) #define VREF (1 << 6) #define STABI_BP (1 << 5) #define IF_PM_L (1 << 4) #define AGCSP (1 << 1) #define AM_ANT_BSW (1 << 0) /* ?? */ /* W */ #define RADIO_CTRL3 (0x07 + BLK2_START) #define AGC_SLVL (1 << 7) #define VOLSH (1 << 6) #define TB_ON (1 << 5) #define AMUTE_L (1 << 4) #define SE_FM (1 << 3) #define SE_BE (1 << 1) #define SE_EXT (1 << 0) /* For LV24000=0, LV24001/24002=Ext source enab. */ /* W */ #define STEREO_CTRL (0x08 + BLK2_START) #define FRCST (1 << 7) #define FMCS(x) ((x) & (0x7 << 4)) #define FMCS_GET(x) (((x) & (0x7 << 4)) >> 4) #define FMCS_SET(x) ((x) << 4) #define AUTOSSR (1 << 3) #define PILTCA (1 << 2) #define SD_PM (1 << 1) #define ST_M (1 << 0) /* W */ #define AUDIO_CTRL1 (0x09 + BLK2_START) #define TONE_LVL(x) ((x) & (0xf << 4)) #define TONE_LVL_GET(x) (((x) & (0xf << 4)) >> 4) #define TONE_LVL_SET(x) ((x) << 4) #define VOL_LVL(x) ((x) & 0xf) #define VOL_LVL_GET(x) ((x) & 0xf) #define VOL_LVL_SET(x) ((x) << 4) /* W */ #define AUDIO_CTRL2 (0x0a + BLK2_START) #define BASS_PP (1 << 0) #define BASS_P (1 << 1) /* BASS_P, BASS_N are mutually-exclusive */ #define BASS_N (1 << 2) #define TREB_P (1 << 3) /* TREB_P, TREB_N are mutually-exclusive */ #define TREB_N (1 << 4) #define DEEMP (1 << 5) #define BPFREQ(x) ((x) & (0x3 << 6)) #define BPFREQ_2_0K (0x0 << 6) #define BPFREQ_1_0K (0x1 << 6) #define BPFREQ_0_5K (0x2 << 6) #define BPFREQ_HIGH (0x3 << 6) /* W */ #define PW_SCTRL (0x0b + BLK2_START) #define SS_CTRL(x) ((x) & (0x7 << 5)) #define SS_CTRL_GET(x) (((x) & (0x7 << 5)) >> 5) #define SS_CTRL_SET(x) ((x) << 5) #define SM_CTRL(x) ((x) & (0x7 << 2)) #define SM_CTRL_GET(x) (((x) & (0x7 << 2)) >> 2) #define SM_CTRL_SET(x) ((x) << 2) #define PW_HPA (1 << 1) /* LV24002 only */ #define PW_RAD (1 << 0) /* shadow for writeable registers */ #define TUNER_POWERED (1 << 0) #define TUNER_PRESENT (1 << 1) #define TUNER_AWAKE (1 << 2) #define TUNER_PRESENCE_CHECKED (1 << 3) static unsigned tuner_status = 0; static unsigned char lv24020lp_regs[0x1c]; static const int sw_osc_low = 10; /* 30; */ static const int sw_osc_high = 240; /* 200; */ static const int sw_cap_low = 0; static const int sw_cap_high = 191; /* linear coefficients used for tuning */ static int coef_00, coef_01, coef_10, coef_11; /* DAC control register set values */ static int if_set, sd_set; static inline bool tuner_awake(void) { return (tuner_status & TUNER_AWAKE) != 0; } /* send a byte to the tuner - expects write mode to be current */ static void lv24020lp_send_byte(unsigned int byte) { int i; for (i = 0; i < 8; i++) { GPIO_OUTPUT_VAL &= ~(1 << FM_CLOCK_PIN); if (byte & 1) GPIO_OUTPUT_VAL |= (1 << FM_DATA_PIN); else GPIO_OUTPUT_VAL &= ~(1 << FM_DATA_PIN); udelay(FM_CLK_DELAY); GPIO_OUTPUT_VAL |= (1 << FM_CLOCK_PIN); udelay(FM_CLK_DELAY); byte >>= 1; } } /* end a write cycle on the tuner */ static void lv24020lp_end_write(void) { /* switch back to read mode */ GPIO_OUTPUT_EN &= ~(1 << FM_DATA_PIN); GPIO_OUTPUT_VAL &= ~(1 << FM_NRW_PIN); udelay(FM_CLK_DELAY); } /* prepare a write cycle on the tuner */ static unsigned int lv24020lp_begin_write(unsigned int address) { /* Get register's block, translate address */ unsigned int blk = (address >= BLK2_START) ? (address -= BLK2_START, BLK2) : BLK1; for (;;) { /* Prepare 3-wire bus pins for write cycle */ GPIO_OUTPUT_VAL |= (1 << FM_NRW_PIN); GPIO_OUTPUT_EN |= (1 << FM_DATA_PIN); udelay(FM_CLK_DELAY); /* current block == register block? */ if (blk == lv24020lp_regs[BLK_SEL]) return address; /* switch block */ lv24020lp_regs[BLK_SEL] = blk; /* data first */ lv24020lp_send_byte(blk); /* then address */ lv24020lp_send_byte(BLK_SEL); lv24020lp_end_write(); } } /* write a byte to a tuner register */ static void lv24020lp_write(unsigned int address, unsigned int data) { /* shadow logical values but do logical=>physical remappings on some registers' data. */ lv24020lp_regs[address] = data; switch (address) { case FM_OSC: /* L: 000..255 * P: 255..000 */ data = 255 - data; break; case FM_CAP: /* L: 000..063, 064..191 * P: 255..192, 127..000 */ data = ((data < 64) ? 255 : (255 - 64)) - data; break; case RADIO_CTRL1: /* L: data * P: data | always "1" bits */ data |= (1 << 4) | (1 << 1) | (1 << 0); break; } /* Check if interface is turned on */ if (!(tuner_status & TUNER_POWERED)) return; address = lv24020lp_begin_write(address); /* data first */ lv24020lp_send_byte(data); /* then address */ lv24020lp_send_byte(address); lv24020lp_end_write(); } /* helpers to set/clear register bits */ static void lv24020lp_write_set(unsigned int address, unsigned int bits) { lv24020lp_write(address, lv24020lp_regs[address] | bits); } static void lv24020lp_write_clear(unsigned int address, unsigned int bits) { lv24020lp_write(address, lv24020lp_regs[address] & ~bits); } /* read a byte from a tuner register */ static unsigned int lv24020lp_read(unsigned int address) { int i; unsigned int toread; /* Check if interface is turned on */ if (!(tuner_status & TUNER_POWERED)) return 0; address = lv24020lp_begin_write(address); /* address */ lv24020lp_send_byte(address); lv24020lp_end_write(); /* data */ toread = 0; for (i = 0; i < 8; i++) { GPIO_OUTPUT_VAL &= ~(1 << FM_CLOCK_PIN); udelay(FM_CLK_DELAY); if (GPIO_INPUT_VAL & (1 << FM_DATA_PIN)) toread |= (1 << i); GPIO_OUTPUT_VAL |= (1 << FM_CLOCK_PIN); udelay(FM_CLK_DELAY); } return toread; } /* enables auto frequency centering */ static void enable_afc(bool enabled) { unsigned int radio_ctrl1 = lv24020lp_regs[RADIO_CTRL1]; if (enabled) { radio_ctrl1 &= ~RST_AFC; radio_ctrl1 |= EN_AFC; } else { radio_ctrl1 |= RST_AFC; radio_ctrl1 &= ~EN_AFC; } lv24020lp_write(RADIO_CTRL1, radio_ctrl1); } static int calculate_coef(unsigned fkhz) { /* Overflow below 66000kHz -- My tuner tunes down to a min of ~72600kHz but datasheet mentions 66000kHz as the minimum. ?? Perhaps 76000kHz was intended? */ return fkhz < 66000 ? 0x7fffffff : 0x81d1a47efc5cb700ull / ((uint64_t)fkhz*fkhz); } static int interpolate_x(int expected_y, int x1, int x2, int y1, int y2) { return y1 == y2 ? 0 : (int64_t)(expected_y - y1)*(x2 - x1) / (y2 - y1) + x1; } static int interpolate_y(int expected_x, int x1, int x2, int y1, int y2) { return x1 == x2 ? 0 : (int64_t)(expected_x - x1)*(y2 - y1) / (x2 - x1) + y1; } /* this performs measurements of IF, FM and Stereo frequencies * Input can be: MSS_FM, MSS_IF, MSS_SD */ static int tuner_measure(unsigned char type, int scale, int duration) { int64_t finval; /* enable measuring */ lv24020lp_write_set(MSRC_SEL, type); lv24020lp_write_clear(CNT_CTRL, CNT_SEL); lv24020lp_write_set(RADIO_CTRL1, EN_MEAS); /* reset counter */ lv24020lp_write_set(CNT_CTRL, CNT1_CLR); lv24020lp_write_clear(CNT_CTRL, CNT1_CLR); /* start counter, delay for specified time and stop it */ lv24020lp_write_set(CNT_CTRL, CNT_EN); udelay(duration*1000 - 16); lv24020lp_write_clear(CNT_CTRL, CNT_EN); /* read tick count */ finval = (lv24020lp_read(CNT_H) << 8) | lv24020lp_read(CNT_L); /* restore measure mode */ lv24020lp_write_clear(RADIO_CTRL1, EN_MEAS); lv24020lp_write_clear(MSRC_SEL, type); /* convert value */ if (type == MSS_FM) finval = scale*finval*256 / duration; else finval = scale*finval / duration; /* This function takes a loooong time and other stuff needs running by now */ yield(); return (int)finval; } /* set the FM oscillator frequency */ static void set_frequency(int freq) { int coef, cap_value, osc_value; int f1, f2, x1, x2; int count; TUNER_LOG_OPEN(); TUNER_LOG("set_frequency(%d)\n", freq); enable_afc(false); /* MHz -> kHz */ freq /= 1000; TUNER_LOG("Select cap:\n"); coef = calculate_coef(freq); cap_value = interpolate_x(coef, sw_cap_low, sw_cap_high, coef_00, coef_01); osc_value = sw_osc_low; lv24020lp_write(FM_OSC, osc_value); /* Just in case - don't go into infinite loop */ for (count = 0; count < 30; count++) { int y0 = interpolate_y(cap_value, sw_cap_low, sw_cap_high, coef_00, coef_01); int y1 = interpolate_y(cap_value, sw_cap_low, sw_cap_high, coef_10, coef_11); int coef_fcur, cap_new, coef_cor, range; lv24020lp_write(FM_CAP, cap_value); range = y1 - y0; f1 = tuner_measure(MSS_FM, 1, 16); coef_fcur = calculate_coef(f1); coef_cor = calculate_coef((f1*1000 + 32*256) / 1000); y0 = coef_cor; y1 = y0 + range; TUNER_LOG("%d %d %d %d %d %d %d %d\n", f1, cap_value, coef, coef_fcur, coef_cor, y0, y1, range); if (coef >= y0 && coef <= y1) { osc_value = interpolate_x(coef, sw_osc_low, sw_osc_high, y0, y1); if (osc_value >= sw_osc_low && osc_value <= sw_osc_high) break; } cap_new = interpolate_x(coef, cap_value, sw_cap_high, coef_fcur, coef_01); if (cap_new == cap_value) { if (coef < coef_fcur) cap_value++; else cap_value--; } else { cap_value = cap_new; } } TUNER_LOG("osc_value: %d\n", osc_value); TUNER_LOG("Tune:\n"); x1 = sw_osc_low, x2 = sw_osc_high; /* FM_OSC already at SW_OSC low and f1 is already the measured frequency */ do { int x2_new; lv24020lp_write(FM_OSC, x2); f2 = tuner_measure(MSS_FM, 1, 16); if (abs(f2 - freq) <= 16) { TUNER_LOG("%d %d %d %d\n", f1, f2, x1, x2); break; } x2_new = interpolate_x(freq, x1, x2, f1, f2); x1 = x2, f1 = f2, x2 = x2_new; TUNER_LOG("%d %d %d %d\n", f1, f2, x1, x2); } while (x2 != 0); if (x2 == 0) { /* May still be close enough */ TUNER_LOG("tuning failed - diff: %d\n", f2 - freq); } enable_afc(true); TUNER_LOG("\n"); TUNER_LOG_SYNC(); } #define TOO_SMALL (1 << 0) #define TOO_BIG (1 << 1) #define APPROACH_UP_1 (1 << 2) #define APPROACH_DOWN_1 (1 << 3) static void fine_step_tune(int (*setcmp)(int regval), int regval, int step) { /* Registers are not always stable, timeout if best fit not found soon enough */ unsigned long abort = current_tick + HZ*2; int flags = 0; while (TIME_BEFORE(current_tick, abort)) { int cmp; regval = regval + step; cmp = setcmp(regval); if (cmp == 0) break; step = abs(step); if (cmp < 0) { flags |= TOO_SMALL; if (step == 1) flags |= APPROACH_UP_1; } else { step = -step; flags |= TOO_BIG; if (step == -1) step |= APPROACH_DOWN_1; } if ((flags & APPROACH_UP_1) && (flags & APPROACH_DOWN_1)) break; /* approached with step=1: best fit value found */ if ((flags & TOO_SMALL) && (flags & TOO_BIG)) { step /= 2; if (step == 0) step = 1; flags &= ~(TOO_SMALL | TOO_BIG); } } } static int if_setcmp(int regval) { lv24020lp_write(IF_OSC, regval); lv24020lp_write(IF_CENTER, regval); lv24020lp_write(IF_BW, 65*regval/100); if_set = tuner_measure(MSS_IF, 1000, 32); /* This register is bounces around by a few hundred Hz and doesn't seem to be precisely tuneable. Just do 110000 +/- 500 since it's not very critical it seems. */ if (abs(if_set - 110000) <= 500) return 0; return if_set < 110000 ? -1 : 1; } static int sd_setcmp(int regval) { lv24020lp_write(SD_OSC, regval); sd_set = tuner_measure(MSS_SD, 1000, 32); if (abs(sd_set - 38300) <= 31) return 0; return sd_set < 38300 ? -1 : 1; } static void set_sleep(bool sleep) { if (sleep || tuner_awake()) return; if ((tuner_status & (TUNER_PRESENT | TUNER_POWERED)) != (TUNER_PRESENT | TUNER_POWERED)) return; enable_afc(false); /* 2. Calibrate the IF frequency at 110 kHz: */ lv24020lp_write_clear(RADIO_CTRL2, IF_PM_L); fine_step_tune(if_setcmp, 0x80, 8); lv24020lp_write_set(RADIO_CTRL2, IF_PM_L); /* 3. Calibrate the stereo decoder clock at 38.3 kHz: */ lv24020lp_write_set(STEREO_CTRL, SD_PM); fine_step_tune(sd_setcmp, 0x80, 8); lv24020lp_write_clear(STEREO_CTRL, SD_PM); /* calculate FM tuning coefficients */ lv24020lp_write(FM_CAP, sw_cap_low); lv24020lp_write(FM_OSC, sw_osc_low); coef_00 = calculate_coef(tuner_measure(MSS_FM, 1, 64)); lv24020lp_write(FM_CAP, sw_cap_high); coef_01 = calculate_coef(tuner_measure(MSS_FM, 1, 64)); lv24020lp_write(FM_CAP, sw_cap_low); lv24020lp_write(FM_OSC, sw_osc_high); coef_10 = calculate_coef(tuner_measure(MSS_FM, 1, 64)); lv24020lp_write(FM_CAP, sw_cap_high); coef_11 = calculate_coef(tuner_measure(MSS_FM, 1, 64)); /* set various audio level settings */ lv24020lp_write(AUDIO_CTRL1, TONE_LVL_SET(0) | VOL_LVL_SET(0)); lv24020lp_write_set(RADIO_CTRL2, AGCSP); lv24020lp_write_set(RADIO_CTRL3, VOLSH); lv24020lp_write(STEREO_CTRL, FMCS_SET(7) | AUTOSSR); lv24020lp_write(PW_SCTRL, SS_CTRL_SET(3) | SM_CTRL_SET(1) | PW_RAD); tuner_status |= TUNER_AWAKE; } static int lp24020lp_tuned(void) { return RSS_FS(lv24020lp_read(RADIO_STAT)) < 0x1f; } static int lv24020lp_debug_info(int setting) { int val = -1; if (setting >= LV24020LP_DEBUG_FIRST && setting <= LV24020LP_DEBUG_LAST) { val = 0; if (tuner_awake()) { switch (setting) { /* tuner-specific debug info */ case LV24020LP_CTRL_STAT: val = lv24020lp_read(CTRL_STAT); break; case LV24020LP_REG_STAT: val = lv24020lp_read(RADIO_STAT); break; case LV24020LP_MSS_FM: val = tuner_measure(MSS_FM, 1, 16); break; case LV24020LP_MSS_IF: val = tuner_measure(MSS_IF, 1000, 16); break; case LV24020LP_MSS_SD: val = tuner_measure(MSS_SD, 1000, 16); break; case LV24020LP_IF_SET: val = if_set; break; case LV24020LP_SD_SET: val = sd_set; break; } } } return val; } /** Public interfaces **/ void lv24020lp_init(void) { mutex_init(&tuner_mtx); } void lv24020lp_lock(void) { mutex_lock(&tuner_mtx); } void lv24020lp_unlock(void) { mutex_unlock(&tuner_mtx); } /* This function expects the driver to be locked externally */ void lv24020lp_power(bool status) { static const unsigned char tuner_defaults[][2] = { /* Block 1 writeable registers */ { MSRC_SEL, AFC_LVL }, { FM_OSC, 0x80 }, { SD_OSC, 0x80 }, { IF_OSC, 0x80 }, { CNT_CTRL, CNT1_CLR | SWP_CNT_L }, { IRQ_MSK, 0x00 }, /* IRQ_LVL -> Low to High */ { FM_CAP, 0x80 }, /* { IRQ_OUT, 0x00 }, No action on this register (skip) */ /* Block 2 writeable registers */ { RADIO_CTRL1, EN_AFC }, { IF_CENTER, 0x80 }, { IF_BW, 65*0x80 / 100 }, /* 65% of IF_OSC */ { RADIO_CTRL2, IF_PM_L }, { RADIO_CTRL3, AGC_SLVL | SE_FM }, { STEREO_CTRL, FMCS_SET(4) | AUTOSSR }, { AUDIO_CTRL1, TONE_LVL_SET(7) | VOL_LVL_SET(7) }, { AUDIO_CTRL2, BPFREQ_HIGH }, /* deemphasis 50us */ { PW_SCTRL, SS_CTRL_SET(3) | SM_CTRL_SET(3) | PW_RAD }, }; unsigned i; if (status) { tuner_status |= (TUNER_PRESENCE_CHECKED | TUNER_POWERED); /* if tuner is present, CHIP ID is 0x09 */ if (lv24020lp_read(CHIP_ID) == 0x09) { tuner_status |= TUNER_PRESENT; /* After power-up, the LV2400x needs to be initialized as follows: */ /* 1. Write default values to the registers: */ lv24020lp_regs[BLK_SEL] = 0; /* Force a switch on the first */ for (i = 0; i < ARRAYLEN(tuner_defaults); i++) lv24020lp_write(tuner_defaults[i][0], tuner_defaults[i][1]); /* Complete the startup calibration if the tuner is woken */ sleep(HZ/10); } } else { /* Power off */ if (tuner_status & TUNER_PRESENT) lv24020lp_write_clear(PW_SCTRL, PW_RAD); tuner_status &= ~(TUNER_POWERED | TUNER_AWAKE); } } int lv24020lp_set(int setting, int value) { int val = 1; mutex_lock(&tuner_mtx); switch(setting) { case RADIO_SLEEP: set_sleep(value); break; case RADIO_FREQUENCY: set_frequency(value); break; case RADIO_SCAN_FREQUENCY: /* TODO: really implement this */ set_frequency(value); val = lp24020lp_tuned(); break; case RADIO_MUTE: if (value) lv24020lp_write_clear(RADIO_CTRL3, AMUTE_L); else lv24020lp_write_set(RADIO_CTRL3, AMUTE_L); break; case RADIO_REGION: if (lv24020lp_region_data[value]) lv24020lp_write_set(AUDIO_CTRL2, DEEMP); else lv24020lp_write_clear(AUDIO_CTRL2, DEEMP); break; case RADIO_FORCE_MONO: if (value) lv24020lp_write_set(STEREO_CTRL, ST_M); else lv24020lp_write_clear(STEREO_CTRL, ST_M); break; default: value = -1; } mutex_unlock(&tuner_mtx); return val; } int lv24020lp_get(int setting) { int val = -1; mutex_lock(&tuner_mtx); switch(setting) { case RADIO_TUNED: /* TODO: really implement this */ val = lp24020lp_tuned(); break; case RADIO_STEREO: val = (lv24020lp_read(RADIO_STAT) & RSS_MS) != 0; break; case RADIO_PRESENT: { bool fmstatus = true; if (!(tuner_status & TUNER_PRESENCE_CHECKED)) fmstatus = tuner_power(true); val = (tuner_status & TUNER_PRESENT) != 0; if (!fmstatus) tuner_power(false); break; } default: val = lv24020lp_debug_info(setting); } mutex_unlock(&tuner_mtx); return val; } #endif /* BOOTLOADER */