blob: 4cb4b688612df37c1aeab771738b8d16675741c2 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
|
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/regulator/richtek,rtmv20-regulator.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Richtek RTMV20 laser diode regulator
maintainers:
- ChiYuan Huang <cy_huang@richtek.com>
description: |
Richtek RTMV20 is a load switch current regulator that can supply up to 6A.
It is used to drive laser diode. There're two signals for chip controls
(Enable/Fail), Enable pin to turn chip on, and Fail pin as fault indication.
There're still four pins for camera control, two inputs (strobe and vsync),
the others for outputs (fsin1 and fsin2). Strobe input to start the current
supply, vsync input from IR camera, and fsin1/fsin2 output for the optional.
properties:
compatible:
const: richtek,rtmv20
reg:
maxItems: 1
wakeup-source: true
interrupts-extend:
maxItems: 1
enable-gpios:
description: A connection of the 'enable' gpio line.
maxItems: 1
ld-pulse-delay-us:
description: |
load current pulse delay in microsecond after strobe pin pulse high.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 0
maximum: 100000
default: 0
ld-pulse-width-us:
description: |
Load current pulse width in microsecond after strobe pin pulse high.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 0
maximum: 10000
default: 1200
fsin1-delay-us:
description: |
Fsin1 pulse high delay in microsecond after vsync signal pulse high.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 0
maximum: 100000
default: 23000
fsin1-width-us:
description: |
Fsin1 pulse high width in microsecond after vsync signal pulse high.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 40
maximum: 10000
default: 160
fsin2-delay-us:
description: |
Fsin2 pulse high delay in microsecond after vsync signal pulse high.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 0
maximum: 100000
default: 23000
fsin2-width-us:
description: |
Fsin2 pulse high width in microsecond after vsync signal pulse high.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 40
maximum: 10000
default: 160
es-pulse-width-us:
description: Eye safety function pulse width limit in microsecond.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 0
maximum: 10000
default: 1200
es-ld-current-microamp:
description: Eye safety function load current limit in microamp.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 0
maximum: 6000000
default: 3000000
lbp-level-microvolt:
description: Low battery protection level in microvolt.
$ref: "/schemas/types.yaml#/definitions/uint32"
minimum: 2400000
maximum: 3700000
default: 2700000
lbp-enable:
description: Low battery protection function enable control.
type: boolean
strobe-polarity-high:
description: Strobe pin active polarity control.
type: boolean
vsync-polarity-high:
description: Vsync pin active polarity control.
type: boolean
fsin-enable:
description: Fsin function enable control.
type: boolean
fsin-output:
description: Fsin function output control.
type: boolean
es-enable:
description: Eye safety function enable control.
type: boolean
patternProperties:
"lsw":
type: object
$ref: "regulator.yaml#"
required:
- compatible
- reg
- wakeup-source
- interrupts-extend
- enable-gpios
- lsw
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
rtmv20@34 {
compatible = "richtek,rtmv20";
reg = <0x34>;
wakeup-source;
interrupts-extend = <&gpio26 2 IRQ_TYPE_LEVEL_LOW>;
enable-gpios = <&gpio26 3 0>;
strobe-polarity-high;
vsync-polarity-high;
lsw {
regulator-name = "rtmv20,lsw";
regulator-min-microamp = <0>;
regulator-max-microamp = <6000000>;
};
};
};
...
|
