// SPDX-License-Identifier: GPL-2.0 /* Copyright (c) 2018, Sensor-Technik Wiedemann GmbH * Copyright (c) 2018-2019, Vladimir Oltean */ #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "sja1105.h" #include "sja1105_sgmii.h" #include "sja1105_tas.h" #define SJA1105_UNKNOWN_MULTICAST 0x010000000000ull static const struct dsa_switch_ops sja1105_switch_ops; static void sja1105_hw_reset(struct gpio_desc *gpio, unsigned int pulse_len, unsigned int startup_delay) { gpiod_set_value_cansleep(gpio, 1); /* Wait for minimum reset pulse length */ msleep(pulse_len); gpiod_set_value_cansleep(gpio, 0); /* Wait until chip is ready after reset */ msleep(startup_delay); } static void sja1105_port_allow_traffic(struct sja1105_l2_forwarding_entry *l2_fwd, int from, int to, bool allow) { if (allow) l2_fwd[from].reach_port |= BIT(to); else l2_fwd[from].reach_port &= ~BIT(to); } /* Structure used to temporarily transport device tree * settings into sja1105_setup */ struct sja1105_dt_port { phy_interface_t phy_mode; sja1105_mii_role_t role; }; static int sja1105_init_mac_settings(struct sja1105_private *priv) { struct sja1105_mac_config_entry default_mac = { /* Enable all 8 priority queues on egress. * Every queue i holds top[i] - base[i] frames. * Sum of top[i] - base[i] is 511 (max hardware limit). */ .top = {0x3F, 0x7F, 0xBF, 0xFF, 0x13F, 0x17F, 0x1BF, 0x1FF}, .base = {0x0, 0x40, 0x80, 0xC0, 0x100, 0x140, 0x180, 0x1C0}, .enabled = {true, true, true, true, true, true, true, true}, /* Keep standard IFG of 12 bytes on egress. */ .ifg = 0, /* Always put the MAC speed in automatic mode, where it can be * adjusted at runtime by PHYLINK. */ .speed = SJA1105_SPEED_AUTO, /* No static correction for 1-step 1588 events */ .tp_delin = 0, .tp_delout = 0, /* Disable aging for critical TTEthernet traffic */ .maxage = 0xFF, /* Internal VLAN (pvid) to apply to untagged ingress */ .vlanprio = 0, .vlanid = 1, .ing_mirr = false, .egr_mirr = false, /* Don't drop traffic with other EtherType than ETH_P_IP */ .drpnona664 = false, /* Don't drop double-tagged traffic */ .drpdtag = false, /* Don't drop untagged traffic */ .drpuntag = false, /* Don't retag 802.1p (VID 0) traffic with the pvid */ .retag = false, /* Disable learning and I/O on user ports by default - * STP will enable it. */ .dyn_learn = false, .egress = false, .ingress = false, }; struct sja1105_mac_config_entry *mac; struct sja1105_table *table; int i; table = &priv->static_config.tables[BLK_IDX_MAC_CONFIG]; /* Discard previous MAC Configuration Table */ if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kcalloc(SJA1105_NUM_PORTS, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = SJA1105_NUM_PORTS; mac = table->entries; for (i = 0; i < SJA1105_NUM_PORTS; i++) { mac[i] = default_mac; if (i == dsa_upstream_port(priv->ds, i)) { /* STP doesn't get called for CPU port, so we need to * set the I/O parameters statically. */ mac[i].dyn_learn = true; mac[i].ingress = true; mac[i].egress = true; } } return 0; } static bool sja1105_supports_sgmii(struct sja1105_private *priv, int port) { if (priv->info->part_no != SJA1105R_PART_NO && priv->info->part_no != SJA1105S_PART_NO) return false; if (port != SJA1105_SGMII_PORT) return false; if (dsa_is_unused_port(priv->ds, port)) return false; return true; } static int sja1105_init_mii_settings(struct sja1105_private *priv, struct sja1105_dt_port *ports) { struct device *dev = &priv->spidev->dev; struct sja1105_xmii_params_entry *mii; struct sja1105_table *table; int i; table = &priv->static_config.tables[BLK_IDX_XMII_PARAMS]; /* Discard previous xMII Mode Parameters Table */ if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kcalloc(SJA1105_MAX_XMII_PARAMS_COUNT, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; /* Override table based on PHYLINK DT bindings */ table->entry_count = SJA1105_MAX_XMII_PARAMS_COUNT; mii = table->entries; for (i = 0; i < SJA1105_NUM_PORTS; i++) { if (dsa_is_unused_port(priv->ds, i)) continue; switch (ports[i].phy_mode) { case PHY_INTERFACE_MODE_MII: mii->xmii_mode[i] = XMII_MODE_MII; break; case PHY_INTERFACE_MODE_RMII: mii->xmii_mode[i] = XMII_MODE_RMII; break; case PHY_INTERFACE_MODE_RGMII: case PHY_INTERFACE_MODE_RGMII_ID: case PHY_INTERFACE_MODE_RGMII_RXID: case PHY_INTERFACE_MODE_RGMII_TXID: mii->xmii_mode[i] = XMII_MODE_RGMII; break; case PHY_INTERFACE_MODE_SGMII: if (!sja1105_supports_sgmii(priv, i)) return -EINVAL; mii->xmii_mode[i] = XMII_MODE_SGMII; break; default: dev_err(dev, "Unsupported PHY mode %s!\n", phy_modes(ports[i].phy_mode)); } /* Even though the SerDes port is able to drive SGMII autoneg * like a PHY would, from the perspective of the XMII tables, * the SGMII port should always be put in MAC mode. */ if (ports[i].phy_mode == PHY_INTERFACE_MODE_SGMII) mii->phy_mac[i] = XMII_MAC; else mii->phy_mac[i] = ports[i].role; } return 0; } static int sja1105_init_static_fdb(struct sja1105_private *priv) { struct sja1105_l2_lookup_entry *l2_lookup; struct sja1105_table *table; int port; table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP]; /* We only populate the FDB table through dynamic L2 Address Lookup * entries, except for a special entry at the end which is a catch-all * for unknown multicast and will be used to control flooding domain. */ if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } if (!priv->info->can_limit_mcast_flood) return 0; table->entries = kcalloc(1, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = 1; l2_lookup = table->entries; /* All L2 multicast addresses have an odd first octet */ l2_lookup[0].macaddr = SJA1105_UNKNOWN_MULTICAST; l2_lookup[0].mask_macaddr = SJA1105_UNKNOWN_MULTICAST; l2_lookup[0].lockeds = true; l2_lookup[0].index = SJA1105_MAX_L2_LOOKUP_COUNT - 1; /* Flood multicast to every port by default */ for (port = 0; port < priv->ds->num_ports; port++) if (!dsa_is_unused_port(priv->ds, port)) l2_lookup[0].destports |= BIT(port); return 0; } static int sja1105_init_l2_lookup_params(struct sja1105_private *priv) { struct sja1105_table *table; u64 max_fdb_entries = SJA1105_MAX_L2_LOOKUP_COUNT / SJA1105_NUM_PORTS; struct sja1105_l2_lookup_params_entry default_l2_lookup_params = { /* Learned FDB entries are forgotten after 300 seconds */ .maxage = SJA1105_AGEING_TIME_MS(300000), /* All entries within a FDB bin are available for learning */ .dyn_tbsz = SJA1105ET_FDB_BIN_SIZE, /* And the P/Q/R/S equivalent setting: */ .start_dynspc = 0, .maxaddrp = {max_fdb_entries, max_fdb_entries, max_fdb_entries, max_fdb_entries, max_fdb_entries, }, /* 2^8 + 2^5 + 2^3 + 2^2 + 2^1 + 1 in Koopman notation */ .poly = 0x97, /* This selects between Independent VLAN Learning (IVL) and * Shared VLAN Learning (SVL) */ .shared_learn = true, /* Don't discard management traffic based on ENFPORT - * we don't perform SMAC port enforcement anyway, so * what we are setting here doesn't matter. */ .no_enf_hostprt = false, /* Don't learn SMAC for mac_fltres1 and mac_fltres0. * Maybe correlate with no_linklocal_learn from bridge driver? */ .no_mgmt_learn = true, /* P/Q/R/S only */ .use_static = true, /* Dynamically learned FDB entries can overwrite other (older) * dynamic FDB entries */ .owr_dyn = true, .drpnolearn = true, }; table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS]; if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kcalloc(SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT; /* This table only has a single entry */ ((struct sja1105_l2_lookup_params_entry *)table->entries)[0] = default_l2_lookup_params; return 0; } static int sja1105_init_static_vlan(struct sja1105_private *priv) { struct sja1105_table *table; struct sja1105_vlan_lookup_entry pvid = { .ving_mirr = 0, .vegr_mirr = 0, .vmemb_port = 0, .vlan_bc = 0, .tag_port = 0, .vlanid = 1, }; struct dsa_switch *ds = priv->ds; int port; table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; /* The static VLAN table will only contain the initial pvid of 1. * All other VLANs are to be configured through dynamic entries, * and kept in the static configuration table as backing memory. */ if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kzalloc(table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = 1; /* VLAN 1: all DT-defined ports are members; no restrictions on * forwarding; always transmit as untagged. */ for (port = 0; port < ds->num_ports; port++) { struct sja1105_bridge_vlan *v; if (dsa_is_unused_port(ds, port)) continue; pvid.vmemb_port |= BIT(port); pvid.vlan_bc |= BIT(port); pvid.tag_port &= ~BIT(port); /* Let traffic that don't need dsa_8021q (e.g. STP, PTP) be * transmitted as untagged. */ v = kzalloc(sizeof(*v), GFP_KERNEL); if (!v) return -ENOMEM; v->port = port; v->vid = 1; v->untagged = true; if (dsa_is_cpu_port(ds, port)) v->pvid = true; list_add(&v->list, &priv->dsa_8021q_vlans); } ((struct sja1105_vlan_lookup_entry *)table->entries)[0] = pvid; return 0; } static int sja1105_init_l2_forwarding(struct sja1105_private *priv) { struct sja1105_l2_forwarding_entry *l2fwd; struct sja1105_table *table; int i, j; table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING]; if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kcalloc(SJA1105_MAX_L2_FORWARDING_COUNT, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = SJA1105_MAX_L2_FORWARDING_COUNT; l2fwd = table->entries; /* First 5 entries define the forwarding rules */ for (i = 0; i < SJA1105_NUM_PORTS; i++) { unsigned int upstream = dsa_upstream_port(priv->ds, i); for (j = 0; j < SJA1105_NUM_TC; j++) l2fwd[i].vlan_pmap[j] = j; if (i == upstream) continue; sja1105_port_allow_traffic(l2fwd, i, upstream, true); sja1105_port_allow_traffic(l2fwd, upstream, i, true); l2fwd[i].bc_domain = BIT(upstream); l2fwd[i].fl_domain = BIT(upstream); l2fwd[upstream].bc_domain |= BIT(i); l2fwd[upstream].fl_domain |= BIT(i); } /* Next 8 entries define VLAN PCP mapping from ingress to egress. * Create a one-to-one mapping. */ for (i = 0; i < SJA1105_NUM_TC; i++) for (j = 0; j < SJA1105_NUM_PORTS; j++) l2fwd[SJA1105_NUM_PORTS + i].vlan_pmap[j] = i; return 0; } static int sja1105_init_l2_forwarding_params(struct sja1105_private *priv) { struct sja1105_l2_forwarding_params_entry default_l2fwd_params = { /* Disallow dynamic reconfiguration of vlan_pmap */ .max_dynp = 0, /* Use a single memory partition for all ingress queues */ .part_spc = { SJA1105_MAX_FRAME_MEMORY, 0, 0, 0, 0, 0, 0, 0 }, }; struct sja1105_table *table; table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING_PARAMS]; if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kcalloc(SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT; /* This table only has a single entry */ ((struct sja1105_l2_forwarding_params_entry *)table->entries)[0] = default_l2fwd_params; return 0; } void sja1105_frame_memory_partitioning(struct sja1105_private *priv) { struct sja1105_l2_forwarding_params_entry *l2_fwd_params; struct sja1105_vl_forwarding_params_entry *vl_fwd_params; struct sja1105_table *table; int max_mem; /* VLAN retagging is implemented using a loopback port that consumes * frame buffers. That leaves less for us. */ if (priv->vlan_state == SJA1105_VLAN_BEST_EFFORT) max_mem = SJA1105_MAX_FRAME_MEMORY_RETAGGING; else max_mem = SJA1105_MAX_FRAME_MEMORY; table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING_PARAMS]; l2_fwd_params = table->entries; l2_fwd_params->part_spc[0] = max_mem; /* If we have any critical-traffic virtual links, we need to reserve * some frame buffer memory for them. At the moment, hardcode the value * at 100 blocks of 128 bytes of memory each. This leaves 829 blocks * remaining for best-effort traffic. TODO: figure out a more flexible * way to perform the frame buffer partitioning. */ if (!priv->static_config.tables[BLK_IDX_VL_FORWARDING].entry_count) return; table = &priv->static_config.tables[BLK_IDX_VL_FORWARDING_PARAMS]; vl_fwd_params = table->entries; l2_fwd_params->part_spc[0] -= SJA1105_VL_FRAME_MEMORY; vl_fwd_params->partspc[0] = SJA1105_VL_FRAME_MEMORY; } static int sja1105_init_general_params(struct sja1105_private *priv) { struct sja1105_general_params_entry default_general_params = { /* Allow dynamic changing of the mirror port */ .mirr_ptacu = true, .switchid = priv->ds->index, /* Priority queue for link-local management frames * (both ingress to and egress from CPU - PTP, STP etc) */ .hostprio = 7, .mac_fltres1 = SJA1105_LINKLOCAL_FILTER_A, .mac_flt1 = SJA1105_LINKLOCAL_FILTER_A_MASK, .incl_srcpt1 = false, .send_meta1 = false, .mac_fltres0 = SJA1105_LINKLOCAL_FILTER_B, .mac_flt0 = SJA1105_LINKLOCAL_FILTER_B_MASK, .incl_srcpt0 = false, .send_meta0 = false, /* The destination for traffic matching mac_fltres1 and * mac_fltres0 on all ports except host_port. Such traffic * receieved on host_port itself would be dropped, except * by installing a temporary 'management route' */ .host_port = dsa_upstream_port(priv->ds, 0), /* Default to an invalid value */ .mirr_port = SJA1105_NUM_PORTS, /* Link-local traffic received on casc_port will be forwarded * to host_port without embedding the source port and device ID * info in the destination MAC address (presumably because it * is a cascaded port and a downstream SJA switch already did * that). Default to an invalid port (to disable the feature) * and overwrite this if we find any DSA (cascaded) ports. */ .casc_port = SJA1105_NUM_PORTS, /* No TTEthernet */ .vllupformat = SJA1105_VL_FORMAT_PSFP, .vlmarker = 0, .vlmask = 0, /* Only update correctionField for 1-step PTP (L2 transport) */ .ignore2stf = 0, /* Forcefully disable VLAN filtering by telling * the switch that VLAN has a different EtherType. */ .tpid = ETH_P_SJA1105, .tpid2 = ETH_P_SJA1105, }; struct sja1105_table *table; table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS]; if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kcalloc(SJA1105_MAX_GENERAL_PARAMS_COUNT, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT; /* This table only has a single entry */ ((struct sja1105_general_params_entry *)table->entries)[0] = default_general_params; return 0; } static int sja1105_init_avb_params(struct sja1105_private *priv) { struct sja1105_avb_params_entry *avb; struct sja1105_table *table; table = &priv->static_config.tables[BLK_IDX_AVB_PARAMS]; /* Discard previous AVB Parameters Table */ if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kcalloc(SJA1105_MAX_AVB_PARAMS_COUNT, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = SJA1105_MAX_AVB_PARAMS_COUNT; avb = table->entries; /* Configure the MAC addresses for meta frames */ avb->destmeta = SJA1105_META_DMAC; avb->srcmeta = SJA1105_META_SMAC; /* On P/Q/R/S, configure the direction of the PTP_CLK pin as input by * default. This is because there might be boards with a hardware * layout where enabling the pin as output might cause an electrical * clash. On E/T the pin is always an output, which the board designers * probably already knew, so even if there are going to be electrical * issues, there's nothing we can do. */ avb->cas_master = false; return 0; } /* The L2 policing table is 2-stage. The table is looked up for each frame * according to the ingress port, whether it was broadcast or not, and the * classified traffic class (given by VLAN PCP). This portion of the lookup is * fixed, and gives access to the SHARINDX, an indirection register pointing * within the policing table itself, which is used to resolve the policer that * will be used for this frame. * * Stage 1 Stage 2 * +------------+--------+ +---------------------------------+ * |Port 0 TC 0 |SHARINDX| | Policer 0: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * |Port 0 TC 1 |SHARINDX| | Policer 1: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * ... | Policer 2: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * |Port 0 TC 7 |SHARINDX| | Policer 3: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * |Port 1 TC 0 |SHARINDX| | Policer 4: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * ... | Policer 5: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * |Port 1 TC 7 |SHARINDX| | Policer 6: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * ... | Policer 7: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * |Port 4 TC 7 |SHARINDX| ... * +------------+--------+ * |Port 0 BCAST|SHARINDX| ... * +------------+--------+ * |Port 1 BCAST|SHARINDX| ... * +------------+--------+ * ... ... * +------------+--------+ +---------------------------------+ * |Port 4 BCAST|SHARINDX| | Policer 44: Rate, Burst, MTU | * +------------+--------+ +---------------------------------+ * * In this driver, we shall use policers 0-4 as statically alocated port * (matchall) policers. So we need to make the SHARINDX for all lookups * corresponding to this ingress port (8 VLAN PCP lookups and 1 broadcast * lookup) equal. * The remaining policers (40) shall be dynamically allocated for flower * policers, where the key is either vlan_prio or dst_mac ff:ff:ff:ff:ff:ff. */ #define SJA1105_RATE_MBPS(speed) (((speed) * 64000) / 1000) static int sja1105_init_l2_policing(struct sja1105_private *priv) { struct sja1105_l2_policing_entry *policing; struct sja1105_table *table; int port, tc; table = &priv->static_config.tables[BLK_IDX_L2_POLICING]; /* Discard previous L2 Policing Table */ if (table->entry_count) { kfree(table->entries); table->entry_count = 0; } table->entries = kcalloc(SJA1105_MAX_L2_POLICING_COUNT, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = SJA1105_MAX_L2_POLICING_COUNT; policing = table->entries; /* Setup shared indices for the matchall policers */ for (port = 0; port < SJA1105_NUM_PORTS; port++) { int bcast = (SJA1105_NUM_PORTS * SJA1105_NUM_TC) + port; for (tc = 0; tc < SJA1105_NUM_TC; tc++) policing[port * SJA1105_NUM_TC + tc].sharindx = port; policing[bcast].sharindx = port; } /* Setup the matchall policer parameters */ for (port = 0; port < SJA1105_NUM_PORTS; port++) { int mtu = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN; if (dsa_is_cpu_port(priv->ds, port)) mtu += VLAN_HLEN; policing[port].smax = 65535; /* Burst size in bytes */ policing[port].rate = SJA1105_RATE_MBPS(1000); policing[port].maxlen = mtu; policing[port].partition = 0; } return 0; } static int sja1105_static_config_load(struct sja1105_private *priv, struct sja1105_dt_port *ports) { int rc; sja1105_static_config_free(&priv->static_config); rc = sja1105_static_config_init(&priv->static_config, priv->info->static_ops, priv->info->device_id); if (rc) return rc; /* Build static configuration */ rc = sja1105_init_mac_settings(priv); if (rc < 0) return rc; rc = sja1105_init_mii_settings(priv, ports); if (rc < 0) return rc; rc = sja1105_init_static_fdb(priv); if (rc < 0) return rc; rc = sja1105_init_static_vlan(priv); if (rc < 0) return rc; rc = sja1105_init_l2_lookup_params(priv); if (rc < 0) return rc; rc = sja1105_init_l2_forwarding(priv); if (rc < 0) return rc; rc = sja1105_init_l2_forwarding_params(priv); if (rc < 0) return rc; rc = sja1105_init_l2_policing(priv); if (rc < 0) return rc; rc = sja1105_init_general_params(priv); if (rc < 0) return rc; rc = sja1105_init_avb_params(priv); if (rc < 0) return rc; /* Send initial configuration to hardware via SPI */ return sja1105_static_config_upload(priv); } static int sja1105_parse_rgmii_delays(struct sja1105_private *priv, const struct sja1105_dt_port *ports) { int i; for (i = 0; i < SJA1105_NUM_PORTS; i++) { if (ports[i].role == XMII_MAC) continue; if (ports[i].phy_mode == PHY_INTERFACE_MODE_RGMII_RXID || ports[i].phy_mode == PHY_INTERFACE_MODE_RGMII_ID) priv->rgmii_rx_delay[i] = true; if (ports[i].phy_mode == PHY_INTERFACE_MODE_RGMII_TXID || ports[i].phy_mode == PHY_INTERFACE_MODE_RGMII_ID) priv->rgmii_tx_delay[i] = true; if ((priv->rgmii_rx_delay[i] || priv->rgmii_tx_delay[i]) && !priv->info->setup_rgmii_delay) return -EINVAL; } return 0; } static int sja1105_parse_ports_node(struct sja1105_private *priv, struct sja1105_dt_port *ports, struct device_node *ports_node) { struct device *dev = &priv->spidev->dev; struct device_node *child; for_each_available_child_of_node(ports_node, child) { struct device_node *phy_node; phy_interface_t phy_mode; u32 index; int err; /* Get switch port number from DT */ if (of_property_read_u32(child, "reg", &index) < 0) { dev_err(dev, "Port number not defined in device tree " "(property \"reg\")\n"); of_node_put(child); return -ENODEV; } /* Get PHY mode from DT */ err = of_get_phy_mode(child, &phy_mode); if (err) { dev_err(dev, "Failed to read phy-mode or " "phy-interface-type property for port %d\n", index); of_node_put(child); return -ENODEV; } ports[index].phy_mode = phy_mode; phy_node = of_parse_phandle(child, "phy-handle", 0); if (!phy_node) { if (!of_phy_is_fixed_link(child)) { dev_err(dev, "phy-handle or fixed-link " "properties missing!\n"); of_node_put(child); return -ENODEV; } /* phy-handle is missing, but fixed-link isn't. * So it's a fixed link. Default to PHY role. */ ports[index].role = XMII_PHY; } else { /* phy-handle present => put port in MAC role */ ports[index].role = XMII_MAC; of_node_put(phy_node); } /* The MAC/PHY role can be overridden with explicit bindings */ if (of_property_read_bool(child, "sja1105,role-mac")) ports[index].role = XMII_MAC; else if (of_property_read_bool(child, "sja1105,role-phy")) ports[index].role = XMII_PHY; } return 0; } static int sja1105_parse_dt(struct sja1105_private *priv, struct sja1105_dt_port *ports) { struct device *dev = &priv->spidev->dev; struct device_node *switch_node = dev->of_node; struct device_node *ports_node; int rc; ports_node = of_get_child_by_name(switch_node, "ports"); if (!ports_node) { dev_err(dev, "Incorrect bindings: absent \"ports\" node\n"); return -ENODEV; } rc = sja1105_parse_ports_node(priv, ports, ports_node); of_node_put(ports_node); return rc; } static int sja1105_sgmii_read(struct sja1105_private *priv, int pcs_reg) { const struct sja1105_regs *regs = priv->info->regs; u32 val; int rc; rc = sja1105_xfer_u32(priv, SPI_READ, regs->sgmii + pcs_reg, &val, NULL); if (rc < 0) return rc; return val; } static int sja1105_sgmii_write(struct sja1105_private *priv, int pcs_reg, u16 pcs_val) { const struct sja1105_regs *regs = priv->info->regs; u32 val = pcs_val; int rc; rc = sja1105_xfer_u32(priv, SPI_WRITE, regs->sgmii + pcs_reg, &val, NULL); if (rc < 0) return rc; return val; } static void sja1105_sgmii_pcs_config(struct sja1105_private *priv, bool an_enabled, bool an_master) { u16 ac = SJA1105_AC_AUTONEG_MODE_SGMII; /* DIGITAL_CONTROL_1: Enable vendor-specific MMD1, allow the PHY to * stop the clock during LPI mode, make the MAC reconfigure * autonomously after PCS autoneg is done, flush the internal FIFOs. */ sja1105_sgmii_write(priv, SJA1105_DC1, SJA1105_DC1_EN_VSMMD1 | SJA1105_DC1_CLOCK_STOP_EN | SJA1105_DC1_MAC_AUTO_SW | SJA1105_DC1_INIT); /* DIGITAL_CONTROL_2: No polarity inversion for TX and RX lanes */ sja1105_sgmii_write(priv, SJA1105_DC2, SJA1105_DC2_TX_POL_INV_DISABLE); /* AUTONEG_CONTROL: Use SGMII autoneg */ if (an_master) ac |= SJA1105_AC_PHY_MODE | SJA1105_AC_SGMII_LINK; sja1105_sgmii_write(priv, SJA1105_AC, ac); /* BASIC_CONTROL: enable in-band AN now, if requested. Otherwise, * sja1105_sgmii_pcs_force_speed must be called later for the link * to become operational. */ if (an_enabled) sja1105_sgmii_write(priv, MII_BMCR, BMCR_ANENABLE | BMCR_ANRESTART); } static void sja1105_sgmii_pcs_force_speed(struct sja1105_private *priv, int speed) { int pcs_speed; switch (speed) { case SPEED_1000: pcs_speed = BMCR_SPEED1000; break; case SPEED_100: pcs_speed = BMCR_SPEED100; break; case SPEED_10: pcs_speed = BMCR_SPEED10; break; default: dev_err(priv->ds->dev, "Invalid speed %d\n", speed); return; } sja1105_sgmii_write(priv, MII_BMCR, pcs_speed | BMCR_FULLDPLX); } /* Convert link speed from SJA1105 to ethtool encoding */ static int sja1105_speed[] = { [SJA1105_SPEED_AUTO] = SPEED_UNKNOWN, [SJA1105_SPEED_10MBPS] = SPEED_10, [SJA1105_SPEED_100MBPS] = SPEED_100, [SJA1105_SPEED_1000MBPS] = SPEED_1000, }; /* Set link speed in the MAC configuration for a specific port. */ static int sja1105_adjust_port_config(struct sja1105_private *priv, int port, int speed_mbps) { struct sja1105_xmii_params_entry *mii; struct sja1105_mac_config_entry *mac; struct device *dev = priv->ds->dev; sja1105_phy_interface_t phy_mode; sja1105_speed_t speed; int rc; /* On P/Q/R/S, one can read from the device via the MAC reconfiguration * tables. On E/T, MAC reconfig tables are not readable, only writable. * We have to *know* what the MAC looks like. For the sake of keeping * the code common, we'll use the static configuration tables as a * reasonable approximation for both E/T and P/Q/R/S. */ mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries; switch (speed_mbps) { case SPEED_UNKNOWN: /* PHYLINK called sja1105_mac_config() to inform us about * the state->interface, but AN has not completed and the * speed is not yet valid. UM10944.pdf says that setting * SJA1105_SPEED_AUTO at runtime disables the port, so that is * ok for power consumption in case AN will never complete - * otherwise PHYLINK should come back with a new update. */ speed = SJA1105_SPEED_AUTO; break; case SPEED_10: speed = SJA1105_SPEED_10MBPS; break; case SPEED_100: speed = SJA1105_SPEED_100MBPS; break; case SPEED_1000: speed = SJA1105_SPEED_1000MBPS; break; default: dev_err(dev, "Invalid speed %iMbps\n", speed_mbps); return -EINVAL; } /* Overwrite SJA1105_SPEED_AUTO from the static MAC configuration * table, since this will be used for the clocking setup, and we no * longer need to store it in the static config (already told hardware * we want auto during upload phase). * Actually for the SGMII port, the MAC is fixed at 1 Gbps and * we need to configure the PCS only (if even that). */ if (sja1105_supports_sgmii(priv, port)) mac[port].speed = SJA1105_SPEED_1000MBPS; else mac[port].speed = speed; /* Write to the dynamic reconfiguration tables */ rc = sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port, &mac[port], true); if (rc < 0) { dev_err(dev, "Failed to write MAC config: %d\n", rc); return rc; } /* Reconfigure the PLLs for the RGMII interfaces (required 125 MHz at * gigabit, 25 MHz at 100 Mbps and 2.5 MHz at 10 Mbps). For MII and * RMII no change of the clock setup is required. Actually, changing * the clock setup does interrupt the clock signal for a certain time * which causes trouble for all PHYs relying on this signal. */ phy_mode = mii->xmii_mode[port]; if (phy_mode != XMII_MODE_RGMII) return 0; return sja1105_clocking_setup_port(priv, port); } /* The SJA1105 MAC programming model is through the static config (the xMII * Mode table cannot be dynamically reconfigured), and we have to program * that early (earlier than PHYLINK calls us, anyway). * So just error out in case the connected PHY attempts to change the initial * system interface MII protocol from what is defined in the DT, at least for * now. */ static bool sja1105_phy_mode_mismatch(struct sja1105_private *priv, int port, phy_interface_t interface) { struct sja1105_xmii_params_entry *mii; sja1105_phy_interface_t phy_mode; mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries; phy_mode = mii->xmii_mode[port]; switch (interface) { case PHY_INTERFACE_MODE_MII: return (phy_mode != XMII_MODE_MII); case PHY_INTERFACE_MODE_RMII: return (phy_mode != XMII_MODE_RMII); case PHY_INTERFACE_MODE_RGMII: case PHY_INTERFACE_MODE_RGMII_ID: case PHY_INTERFACE_MODE_RGMII_RXID: case PHY_INTERFACE_MODE_RGMII_TXID: return (phy_mode != XMII_MODE_RGMII); case PHY_INTERFACE_MODE_SGMII: return (phy_mode != XMII_MODE_SGMII); default: return true; } } static void sja1105_mac_config(struct dsa_switch *ds, int port, unsigned int mode, const struct phylink_link_state *state) { struct sja1105_private *priv = ds->priv; bool is_sgmii = sja1105_supports_sgmii(priv, port); if (sja1105_phy_mode_mismatch(priv, port, state->interface)) { dev_err(ds->dev, "Changing PHY mode to %s not supported!\n", phy_modes(state->interface)); return; } if (phylink_autoneg_inband(mode) && !is_sgmii) { dev_err(ds->dev, "In-band AN not supported!\n"); return; } if (is_sgmii) sja1105_sgmii_pcs_config(priv, phylink_autoneg_inband(mode), false); } static void sja1105_mac_link_down(struct dsa_switch *ds, int port, unsigned int mode, phy_interface_t interface) { sja1105_inhibit_tx(ds->priv, BIT(port), true); } static void sja1105_mac_link_up(struct dsa_switch *ds, int port, unsigned int mode, phy_interface_t interface, struct phy_device *phydev, int speed, int duplex, bool tx_pause, bool rx_pause) { struct sja1105_private *priv = ds->priv; sja1105_adjust_port_config(priv, port, speed); if (sja1105_supports_sgmii(priv, port) && !phylink_autoneg_inband(mode)) sja1105_sgmii_pcs_force_speed(priv, speed); sja1105_inhibit_tx(priv, BIT(port), false); } static void sja1105_phylink_validate(struct dsa_switch *ds, int port, unsigned long *supported, struct phylink_link_state *state) { /* Construct a new mask which exhaustively contains all link features * supported by the MAC, and then apply that (logical AND) to what will * be sent to the PHY for "marketing". */ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; struct sja1105_private *priv = ds->priv; struct sja1105_xmii_params_entry *mii; mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries; /* include/linux/phylink.h says: * When @state->interface is %PHY_INTERFACE_MODE_NA, phylink * expects the MAC driver to return all supported link modes. */ if (state->interface != PHY_INTERFACE_MODE_NA && sja1105_phy_mode_mismatch(priv, port, state->interface)) { bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS); return; } /* The MAC does not support pause frames, and also doesn't * support half-duplex traffic modes. */ phylink_set(mask, Autoneg); phylink_set(mask, MII); phylink_set(mask, 10baseT_Full); phylink_set(mask, 100baseT_Full); phylink_set(mask, 100baseT1_Full); if (mii->xmii_mode[port] == XMII_MODE_RGMII || mii->xmii_mode[port] == XMII_MODE_SGMII) phylink_set(mask, 1000baseT_Full); bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS); bitmap_and(state->advertising, state->advertising, mask, __ETHTOOL_LINK_MODE_MASK_NBITS); } static int sja1105_mac_pcs_get_state(struct dsa_switch *ds, int port, struct phylink_link_state *state) { struct sja1105_private *priv = ds->priv; int ais; /* Read the vendor-specific AUTONEG_INTR_STATUS register */ ais = sja1105_sgmii_read(priv, SJA1105_AIS); if (ais < 0) return ais; switch (SJA1105_AIS_SPEED(ais)) { case 0: state->speed = SPEED_10; break; case 1: state->speed = SPEED_100; break; case 2: state->speed = SPEED_1000; break; default: dev_err(ds->dev, "Invalid SGMII PCS speed %lu\n", SJA1105_AIS_SPEED(ais)); } state->duplex = SJA1105_AIS_DUPLEX_MODE(ais); state->an_complete = SJA1105_AIS_COMPLETE(ais); state->link = SJA1105_AIS_LINK_STATUS(ais); return 0; } static int sja1105_find_static_fdb_entry(struct sja1105_private *priv, int port, const struct sja1105_l2_lookup_entry *requested) { struct sja1105_l2_lookup_entry *l2_lookup; struct sja1105_table *table; int i; table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP]; l2_lookup = table->entries; for (i = 0; i < table->entry_count; i++) if (l2_lookup[i].macaddr == requested->macaddr && l2_lookup[i].vlanid == requested->vlanid && l2_lookup[i].destports & BIT(port)) return i; return -1; } /* We want FDB entries added statically through the bridge command to persist * across switch resets, which are a common thing during normal SJA1105 * operation. So we have to back them up in the static configuration tables * and hence apply them on next static config upload... yay! */ static int sja1105_static_fdb_change(struct sja1105_private *priv, int port, const struct sja1105_l2_lookup_entry *requested, bool keep) { struct sja1105_l2_lookup_entry *l2_lookup; struct sja1105_table *table; int rc, match; table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP]; match = sja1105_find_static_fdb_entry(priv, port, requested); if (match < 0) { /* Can't delete a missing entry. */ if (!keep) return 0; /* No match => new entry */ rc = sja1105_table_resize(table, table->entry_count + 1); if (rc) return rc; match = table->entry_count - 1; } /* Assign pointer after the resize (it may be new memory) */ l2_lookup = table->entries; /* We have a match. * If the job was to add this FDB entry, it's already done (mostly * anyway, since the port forwarding mask may have changed, case in * which we update it). * Otherwise we have to delete it. */ if (keep) { l2_lookup[match] = *requested; return 0; } /* To remove, the strategy is to overwrite the element with * the last one, and then reduce the array size by 1 */ l2_lookup[match] = l2_lookup[table->entry_count - 1]; return sja1105_table_resize(table, table->entry_count - 1); } /* First-generation switches have a 4-way set associative TCAM that * holds the FDB entries. An FDB index spans from 0 to 1023 and is comprised of * a "bin" (grouping of 4 entries) and a "way" (an entry within a bin). * For the placement of a newly learnt FDB entry, the switch selects the bin * based on a hash function, and the way within that bin incrementally. */ static int sja1105et_fdb_index(int bin, int way) { return bin * SJA1105ET_FDB_BIN_SIZE + way; } static int sja1105et_is_fdb_entry_in_bin(struct sja1105_private *priv, int bin, const u8 *addr, u16 vid, struct sja1105_l2_lookup_entry *match, int *last_unused) { int way; for (way = 0; way < SJA1105ET_FDB_BIN_SIZE; way++) { struct sja1105_l2_lookup_entry l2_lookup = {0}; int index = sja1105et_fdb_index(bin, way); /* Skip unused entries, optionally marking them * into the return value */ if (sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, index, &l2_lookup)) { if (last_unused) *last_unused = way; continue; } if (l2_lookup.macaddr == ether_addr_to_u64(addr) && l2_lookup.vlanid == vid) { if (match) *match = l2_lookup; return way; } } /* Return an invalid entry index if not found */ return -1; } int sja1105et_fdb_add(struct dsa_switch *ds, int port, const unsigned char *addr, u16 vid) { struct sja1105_l2_lookup_entry l2_lookup = {0}; struct sja1105_private *priv = ds->priv; struct device *dev = ds->dev; int last_unused = -1; int bin, way, rc; bin = sja1105et_fdb_hash(priv, addr, vid); way = sja1105et_is_fdb_entry_in_bin(priv, bin, addr, vid, &l2_lookup, &last_unused); if (way >= 0) { /* We have an FDB entry. Is our port in the destination * mask? If yes, we need to do nothing. If not, we need * to rewrite the entry by adding this port to it. */ if (l2_lookup.destports & BIT(port)) return 0; l2_lookup.destports |= BIT(port); } else { int index = sja1105et_fdb_index(bin, way); /* We don't have an FDB entry. We construct a new one and * try to find a place for it within the FDB table. */ l2_lookup.macaddr = ether_addr_to_u64(addr); l2_lookup.destports = BIT(port); l2_lookup.vlanid = vid; if (last_unused >= 0) { way = last_unused; } else { /* Bin is full, need to evict somebody. * Choose victim at random. If you get these messages * often, you may need to consider changing the * distribution function: * static_config[BLK_IDX_L2_LOOKUP_PARAMS].entries->poly */ get_random_bytes(&way, sizeof(u8)); way %= SJA1105ET_FDB_BIN_SIZE; dev_warn(dev, "Warning, FDB bin %d full while adding entry for %pM. Evicting entry %u.\n", bin, addr, way); /* Evict entry */ sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, index, NULL, false); } } l2_lookup.index = sja1105et_fdb_index(bin, way); rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, l2_lookup.index, &l2_lookup, true); if (rc < 0) return rc; return sja1105_static_fdb_change(priv, port, &l2_lookup, true); } int sja1105et_fdb_del(struct dsa_switch *ds, int port, const unsigned char *addr, u16 vid) { struct sja1105_l2_lookup_entry l2_lookup = {0}; struct sja1105_private *priv = ds->priv; int index, bin, way, rc; bool keep; bin = sja1105et_fdb_hash(priv, addr, vid); way = sja1105et_is_fdb_entry_in_bin(priv, bin, addr, vid, &l2_lookup, NULL); if (way < 0) return 0; index = sja1105et_fdb_index(bin, way); /* We have an FDB entry. Is our port in the destination mask? If yes, * we need to remove it. If the resulting port mask becomes empty, we * need to completely evict the FDB entry. * Otherwise we just write it back. */ l2_lookup.destports &= ~BIT(port); if (l2_lookup.destports) keep = true; else keep = false; rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, index, &l2_lookup, keep); if (rc < 0) return rc; return sja1105_static_fdb_change(priv, port, &l2_lookup, keep); } int sja1105pqrs_fdb_add(struct dsa_switch *ds, int port, const unsigned char *addr, u16 vid) { struct sja1105_l2_lookup_entry l2_lookup = {0}; struct sja1105_private *priv = ds->priv; int rc, i; /* Search for an existing entry in the FDB table */ l2_lookup.macaddr = ether_addr_to_u64(addr); l2_lookup.vlanid = vid; l2_lookup.iotag = SJA1105_S_TAG; l2_lookup.mask_macaddr = GENMASK_ULL(ETH_ALEN * 8 - 1, 0); if (priv->vlan_state != SJA1105_VLAN_UNAWARE) { l2_lookup.mask_vlanid = VLAN_VID_MASK; l2_lookup.mask_iotag = BIT(0); } else { l2_lookup.mask_vlanid = 0; l2_lookup.mask_iotag = 0; } l2_lookup.destports = BIT(port); rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, SJA1105_SEARCH, &l2_lookup); if (rc == 0) { /* Found and this port is already in the entry's * port mask => job done */ if (l2_lookup.destports & BIT(port)) return 0; /* l2_lookup.index is populated by the switch in case it * found something. */ l2_lookup.destports |= BIT(port); goto skip_finding_an_index; } /* Not found, so try to find an unused spot in the FDB. * This is slightly inefficient because the strategy is knock-knock at * every possible position from 0 to 1023. */ for (i = 0; i < SJA1105_MAX_L2_LOOKUP_COUNT; i++) { rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, i, NULL); if (rc < 0) break; } if (i == SJA1105_MAX_L2_LOOKUP_COUNT) { dev_err(ds->dev, "FDB is full, cannot add entry.\n"); return -EINVAL; } l2_lookup.lockeds = true; l2_lookup.index = i; skip_finding_an_index: rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, l2_lookup.index, &l2_lookup, true); if (rc < 0) return rc; return sja1105_static_fdb_change(priv, port, &l2_lookup, true); } int sja1105pqrs_fdb_del(struct dsa_switch *ds, int port, const unsigned char *addr, u16 vid) { struct sja1105_l2_lookup_entry l2_lookup = {0}; struct sja1105_private *priv = ds->priv; bool keep; int rc; l2_lookup.macaddr = ether_addr_to_u64(addr); l2_lookup.vlanid = vid; l2_lookup.iotag = SJA1105_S_TAG; l2_lookup.mask_macaddr = GENMASK_ULL(ETH_ALEN * 8 - 1, 0); if (priv->vlan_state != SJA1105_VLAN_UNAWARE) { l2_lookup.mask_vlanid = VLAN_VID_MASK; l2_lookup.mask_iotag = BIT(0); } else { l2_lookup.mask_vlanid = 0; l2_lookup.mask_iotag = 0; } l2_lookup.destports = BIT(port); rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, SJA1105_SEARCH, &l2_lookup); if (rc < 0) return 0; l2_lookup.destports &= ~BIT(port); /* Decide whether we remove just this port from the FDB entry, * or if we remove it completely. */ if (l2_lookup.destports) keep = true; else keep = false; rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, l2_lookup.index, &l2_lookup, keep); if (rc < 0) return rc; return sja1105_static_fdb_change(priv, port, &l2_lookup, keep); } static int sja1105_fdb_add(struct dsa_switch *ds, int port, const unsigned char *addr, u16 vid) { struct sja1105_private *priv = ds->priv; /* dsa_8021q is in effect when the bridge's vlan_filtering isn't, * so the switch still does some VLAN processing internally. * But Shared VLAN Learning (SVL) is also active, and it will take * care of autonomous forwarding between the unique pvid's of each * port. Here we just make sure that users can't add duplicate FDB * entries when in this mode - the actual VID doesn't matter except * for what gets printed in 'bridge fdb show'. In the case of zero, * no VID gets printed at all. */ if (priv->vlan_state != SJA1105_VLAN_FILTERING_FULL) vid = 0; return priv->info->fdb_add_cmd(ds, port, addr, vid); } static int sja1105_fdb_del(struct dsa_switch *ds, int port, const unsigned char *addr, u16 vid) { struct sja1105_private *priv = ds->priv; if (priv->vlan_state != SJA1105_VLAN_FILTERING_FULL) vid = 0; return priv->info->fdb_del_cmd(ds, port, addr, vid); } static int sja1105_fdb_dump(struct dsa_switch *ds, int port, dsa_fdb_dump_cb_t *cb, void *data) { struct sja1105_private *priv = ds->priv; struct device *dev = ds->dev; int i; for (i = 0; i < SJA1105_MAX_L2_LOOKUP_COUNT; i++) { struct sja1105_l2_lookup_entry l2_lookup = {0}; u8 macaddr[ETH_ALEN]; int rc; rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, i, &l2_lookup); /* No fdb entry at i, not an issue */ if (rc == -ENOENT) continue; if (rc) { dev_err(dev, "Failed to dump FDB: %d\n", rc); return rc; } /* FDB dump callback is per port. This means we have to * disregard a valid entry if it's not for this port, even if * only to revisit it later. This is inefficient because the * 1024-sized FDB table needs to be traversed 4 times through * SPI during a 'bridge fdb show' command. */ if (!(l2_lookup.destports & BIT(port))) continue; /* We need to hide the FDB entry for unknown multicast */ if (l2_lookup.macaddr == SJA1105_UNKNOWN_MULTICAST && l2_lookup.mask_macaddr == SJA1105_UNKNOWN_MULTICAST) continue; u64_to_ether_addr(l2_lookup.macaddr, macaddr); /* We need to hide the dsa_8021q VLANs from the user. */ if (priv->vlan_state == SJA1105_VLAN_UNAWARE) l2_lookup.vlanid = 0; cb(macaddr, l2_lookup.vlanid, l2_lookup.lockeds, data); } return 0; } static int sja1105_mdb_add(struct dsa_switch *ds, int port, const struct switchdev_obj_port_mdb *mdb) { return sja1105_fdb_add(ds, port, mdb->addr, mdb->vid); } static int sja1105_mdb_del(struct dsa_switch *ds, int port, const struct switchdev_obj_port_mdb *mdb) { return sja1105_fdb_del(ds, port, mdb->addr, mdb->vid); } static int sja1105_bridge_member(struct dsa_switch *ds, int port, struct net_device *br, bool member) { struct sja1105_l2_forwarding_entry *l2_fwd; struct sja1105_private *priv = ds->priv; int i, rc; l2_fwd = priv->static_config.tables[BLK_IDX_L2_FORWARDING].entries; for (i = 0; i < SJA1105_NUM_PORTS; i++) { /* Add this port to the forwarding matrix of the * other ports in the same bridge, and viceversa. */ if (!dsa_is_user_port(ds, i)) continue; /* For the ports already under the bridge, only one thing needs * to be done, and that is to add this port to their * reachability domain. So we can perform the SPI write for * them immediately. However, for this port itself (the one * that is new to the bridge), we need to add all other ports * to its reachability domain. So we do that incrementally in * this loop, and perform the SPI write only at the end, once * the domain contains all other bridge ports. */ if (i == port) continue; if (dsa_to_port(ds, i)->bridge_dev != br) continue; sja1105_port_allow_traffic(l2_fwd, i, port, member); sja1105_port_allow_traffic(l2_fwd, port, i, member); rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING, i, &l2_fwd[i], true); if (rc < 0) return rc; } return sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING, port, &l2_fwd[port], true); } static void sja1105_bridge_stp_state_set(struct dsa_switch *ds, int port, u8 state) { struct sja1105_private *priv = ds->priv; struct sja1105_mac_config_entry *mac; mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; switch (state) { case BR_STATE_DISABLED: case BR_STATE_BLOCKING: /* From UM10944 description of DRPDTAG (why put this there?): * "Management traffic flows to the port regardless of the state * of the INGRESS flag". So BPDUs are still be allowed to pass. * At the moment no difference between DISABLED and BLOCKING. */ mac[port].ingress = false; mac[port].egress = false; mac[port].dyn_learn = false; break; case BR_STATE_LISTENING: mac[port].ingress = true; mac[port].egress = false; mac[port].dyn_learn = false; break; case BR_STATE_LEARNING: mac[port].ingress = true; mac[port].egress = false; mac[port].dyn_learn = !!(priv->learn_ena & BIT(port)); break; case BR_STATE_FORWARDING: mac[port].ingress = true; mac[port].egress = true; mac[port].dyn_learn = !!(priv->learn_ena & BIT(port)); break; default: dev_err(ds->dev, "invalid STP state: %d\n", state); return; } sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port, &mac[port], true); } static int sja1105_bridge_join(struct dsa_switch *ds, int port, struct net_device *br) { return sja1105_bridge_member(ds, port, br, true); } static void sja1105_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br) { sja1105_bridge_member(ds, port, br, false); } #define BYTES_PER_KBIT (1000LL / 8) static int sja1105_find_unused_cbs_shaper(struct sja1105_private *priv) { int i; for (i = 0; i < priv->info->num_cbs_shapers; i++) if (!priv->cbs[i].idle_slope && !priv->cbs[i].send_slope) return i; return -1; } static int sja1105_delete_cbs_shaper(struct sja1105_private *priv, int port, int prio) { int i; for (i = 0; i < priv->info->num_cbs_shapers; i++) { struct sja1105_cbs_entry *cbs = &priv->cbs[i]; if (cbs->port == port && cbs->prio == prio) { memset(cbs, 0, sizeof(*cbs)); return sja1105_dynamic_config_write(priv, BLK_IDX_CBS, i, cbs, true); } } return 0; } static int sja1105_setup_tc_cbs(struct dsa_switch *ds, int port, struct tc_cbs_qopt_offload *offload) { struct sja1105_private *priv = ds->priv; struct sja1105_cbs_entry *cbs; int index; if (!offload->enable) return sja1105_delete_cbs_shaper(priv, port, offload->queue); index = sja1105_find_unused_cbs_shaper(priv); if (index < 0) return -ENOSPC; cbs = &priv->cbs[index]; cbs->port = port; cbs->prio = offload->queue; /* locredit and sendslope are negative by definition. In hardware, * positive values must be provided, and the negative sign is implicit. */ cbs->credit_hi = offload->hicredit; cbs->credit_lo = abs(offload->locredit); /* User space is in kbits/sec, hardware in bytes/sec */ cbs->idle_slope = offload->idleslope * BYTES_PER_KBIT; cbs->send_slope = abs(offload->sendslope * BYTES_PER_KBIT); /* Convert the negative values from 64-bit 2's complement * to 32-bit 2's complement (for the case of 0x80000000 whose * negative is still negative). */ cbs->credit_lo &= GENMASK_ULL(31, 0); cbs->send_slope &= GENMASK_ULL(31, 0); return sja1105_dynamic_config_write(priv, BLK_IDX_CBS, index, cbs, true); } static int sja1105_reload_cbs(struct sja1105_private *priv) { int rc = 0, i; for (i = 0; i < priv->info->num_cbs_shapers; i++) { struct sja1105_cbs_entry *cbs = &priv->cbs[i]; if (!cbs->idle_slope && !cbs->send_slope) continue; rc = sja1105_dynamic_config_write(priv, BLK_IDX_CBS, i, cbs, true); if (rc) break; } return rc; } static const char * const sja1105_reset_reasons[] = { [SJA1105_VLAN_FILTERING] = "VLAN filtering", [SJA1105_RX_HWTSTAMPING] = "RX timestamping", [SJA1105_AGEING_TIME] = "Ageing time", [SJA1105_SCHEDULING] = "Time-aware scheduling", [SJA1105_BEST_EFFORT_POLICING] = "Best-effort policing", [SJA1105_VIRTUAL_LINKS] = "Virtual links", }; /* For situations where we need to change a setting at runtime that is only * available through the static configuration, resetting the switch in order * to upload the new static config is unavoidable. Back up the settings we * modify at runtime (currently only MAC) and restore them after uploading, * such that this operation is relatively seamless. */ int sja1105_static_config_reload(struct sja1105_private *priv, enum sja1105_reset_reason reason) { struct ptp_system_timestamp ptp_sts_before; struct ptp_system_timestamp ptp_sts_after; struct sja1105_mac_config_entry *mac; int speed_mbps[SJA1105_NUM_PORTS]; struct dsa_switch *ds = priv->ds; s64 t1, t2, t3, t4; s64 t12, t34; u16 bmcr = 0; int rc, i; s64 now; mutex_lock(&priv->mgmt_lock); mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; /* Back up the dynamic link speed changed by sja1105_adjust_port_config * in order to temporarily restore it to SJA1105_SPEED_AUTO - which the * switch wants to see in the static config in order to allow us to * change it through the dynamic interface later. */ for (i = 0; i < SJA1105_NUM_PORTS; i++) { speed_mbps[i] = sja1105_speed[mac[i].speed]; mac[i].speed = SJA1105_SPEED_AUTO; } if (sja1105_supports_sgmii(priv, SJA1105_SGMII_PORT)) bmcr = sja1105_sgmii_read(priv, MII_BMCR); /* No PTP operations can run right now */ mutex_lock(&priv->ptp_data.lock); rc = __sja1105_ptp_gettimex(ds, &now, &ptp_sts_before); if (rc < 0) goto out_unlock_ptp; /* Reset switch and send updated static configuration */ rc = sja1105_static_config_upload(priv); if (rc < 0) goto out_unlock_ptp; rc = __sja1105_ptp_settime(ds, 0, &ptp_sts_after); if (rc < 0) goto out_unlock_ptp; t1 = timespec64_to_ns(&ptp_sts_before.pre_ts); t2 = timespec64_to_ns(&ptp_sts_before.post_ts); t3 = timespec64_to_ns(&ptp_sts_after.pre_ts); t4 = timespec64_to_ns(&ptp_sts_after.post_ts); /* Mid point, corresponds to pre-reset PTPCLKVAL */ t12 = t1 + (t2 - t1) / 2; /* Mid point, corresponds to post-reset PTPCLKVAL, aka 0 */ t34 = t3 + (t4 - t3) / 2; /* Advance PTPCLKVAL by the time it took since its readout */ now += (t34 - t12); __sja1105_ptp_adjtime(ds, now); out_unlock_ptp: mutex_unlock(&priv->ptp_data.lock); dev_info(priv->ds->dev, "Reset switch and programmed static config. Reason: %s\n", sja1105_reset_reasons[reason]); /* Configure the CGU (PLLs) for MII and RMII PHYs. * For these interfaces there is no dynamic configuration * needed, since PLLs have same settings at all speeds. */ rc = sja1105_clocking_setup(priv); if (rc < 0) goto out; for (i = 0; i < SJA1105_NUM_PORTS; i++) { rc = sja1105_adjust_port_config(priv, i, speed_mbps[i]); if (rc < 0) goto out; } if (sja1105_supports_sgmii(priv, SJA1105_SGMII_PORT)) { bool an_enabled = !!(bmcr & BMCR_ANENABLE); sja1105_sgmii_pcs_config(priv, an_enabled, false); if (!an_enabled) { int speed = SPEED_UNKNOWN; if (bmcr & BMCR_SPEED1000) speed = SPEED_1000; else if (bmcr & BMCR_SPEED100) speed = SPEED_100; else if (bmcr & BMCR_SPEED10) speed = SPEED_10; sja1105_sgmii_pcs_force_speed(priv, speed); } } rc = sja1105_reload_cbs(priv); if (rc < 0) goto out; out: mutex_unlock(&priv->mgmt_lock); return rc; } static int sja1105_pvid_apply(struct sja1105_private *priv, int port, u16 pvid) { struct sja1105_mac_config_entry *mac; mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; mac[port].vlanid = pvid; return sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port, &mac[port], true); } static int sja1105_crosschip_bridge_join(struct dsa_switch *ds, int tree_index, int sw_index, int other_port, struct net_device *br) { struct dsa_switch *other_ds = dsa_switch_find(tree_index, sw_index); struct sja1105_private *other_priv = other_ds->priv; struct sja1105_private *priv = ds->priv; int port, rc; if (other_ds->ops != &sja1105_switch_ops) return 0; for (port = 0; port < ds->num_ports; port++) { if (!dsa_is_user_port(ds, port)) continue; if (dsa_to_port(ds, port)->bridge_dev != br) continue; rc = dsa_8021q_crosschip_bridge_join(priv->dsa_8021q_ctx, port, other_priv->dsa_8021q_ctx, other_port); if (rc) return rc; rc = dsa_8021q_crosschip_bridge_join(other_priv->dsa_8021q_ctx, other_port, priv->dsa_8021q_ctx, port); if (rc) return rc; } return 0; } static void sja1105_crosschip_bridge_leave(struct dsa_switch *ds, int tree_index, int sw_index, int other_port, struct net_device *br) { struct dsa_switch *other_ds = dsa_switch_find(tree_index, sw_index); struct sja1105_private *other_priv = other_ds->priv; struct sja1105_private *priv = ds->priv; int port; if (other_ds->ops != &sja1105_switch_ops) return; for (port = 0; port < ds->num_ports; port++) { if (!dsa_is_user_port(ds, port)) continue; if (dsa_to_port(ds, port)->bridge_dev != br) continue; dsa_8021q_crosschip_bridge_leave(priv->dsa_8021q_ctx, port, other_priv->dsa_8021q_ctx, other_port); dsa_8021q_crosschip_bridge_leave(other_priv->dsa_8021q_ctx, other_port, priv->dsa_8021q_ctx, port); } } static int sja1105_setup_8021q_tagging(struct dsa_switch *ds, bool enabled) { struct sja1105_private *priv = ds->priv; int rc; rc = dsa_8021q_setup(priv->dsa_8021q_ctx, enabled); if (rc) return rc; dev_info(ds->dev, "%s switch tagging\n", enabled ? "Enabled" : "Disabled"); return 0; } static enum dsa_tag_protocol sja1105_get_tag_protocol(struct dsa_switch *ds, int port, enum dsa_tag_protocol mp) { return DSA_TAG_PROTO_SJA1105; } static int sja1105_find_free_subvlan(u16 *subvlan_map, bool pvid) { int subvlan; if (pvid) return 0; for (subvlan = 1; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++) if (subvlan_map[subvlan] == VLAN_N_VID) return subvlan; return -1; } static int sja1105_find_subvlan(u16 *subvlan_map, u16 vid) { int subvlan; for (subvlan = 0; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++) if (subvlan_map[subvlan] == vid) return subvlan; return -1; } static int sja1105_find_committed_subvlan(struct sja1105_private *priv, int port, u16 vid) { struct sja1105_port *sp = &priv->ports[port]; return sja1105_find_subvlan(sp->subvlan_map, vid); } static void sja1105_init_subvlan_map(u16 *subvlan_map) { int subvlan; for (subvlan = 0; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++) subvlan_map[subvlan] = VLAN_N_VID; } static void sja1105_commit_subvlan_map(struct sja1105_private *priv, int port, u16 *subvlan_map) { struct sja1105_port *sp = &priv->ports[port]; int subvlan; for (subvlan = 0; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++) sp->subvlan_map[subvlan] = subvlan_map[subvlan]; } static int sja1105_is_vlan_configured(struct sja1105_private *priv, u16 vid) { struct sja1105_vlan_lookup_entry *vlan; int count, i; vlan = priv->static_config.tables[BLK_IDX_VLAN_LOOKUP].entries; count = priv->static_config.tables[BLK_IDX_VLAN_LOOKUP].entry_count; for (i = 0; i < count; i++) if (vlan[i].vlanid == vid) return i; /* Return an invalid entry index if not found */ return -1; } static int sja1105_find_retagging_entry(struct sja1105_retagging_entry *retagging, int count, int from_port, u16 from_vid, u16 to_vid) { int i; for (i = 0; i < count; i++) if (retagging[i].ing_port == BIT(from_port) && retagging[i].vlan_ing == from_vid && retagging[i].vlan_egr == to_vid) return i; /* Return an invalid entry index if not found */ return -1; } static int sja1105_commit_vlans(struct sja1105_private *priv, struct sja1105_vlan_lookup_entry *new_vlan, struct sja1105_retagging_entry *new_retagging, int num_retagging) { struct sja1105_retagging_entry *retagging; struct sja1105_vlan_lookup_entry *vlan; struct sja1105_table *table; int num_vlans = 0; int rc, i, k = 0; /* VLAN table */ table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; vlan = table->entries; for (i = 0; i < VLAN_N_VID; i++) { int match = sja1105_is_vlan_configured(priv, i); if (new_vlan[i].vlanid != VLAN_N_VID) num_vlans++; if (new_vlan[i].vlanid == VLAN_N_VID && match >= 0) { /* Was there before, no longer is. Delete */ dev_dbg(priv->ds->dev, "Deleting VLAN %d\n", i); rc = sja1105_dynamic_config_write(priv, BLK_IDX_VLAN_LOOKUP, i, &vlan[match], false); if (rc < 0) return rc; } else if (new_vlan[i].vlanid != VLAN_N_VID) { /* Nothing changed, don't do anything */ if (match >= 0 && vlan[match].vlanid == new_vlan[i].vlanid && vlan[match].tag_port == new_vlan[i].tag_port && vlan[match].vlan_bc == new_vlan[i].vlan_bc && vlan[match].vmemb_port == new_vlan[i].vmemb_port) continue; /* Update entry */ dev_dbg(priv->ds->dev, "Updating VLAN %d\n", i); rc = sja1105_dynamic_config_write(priv, BLK_IDX_VLAN_LOOKUP, i, &new_vlan[i], true); if (rc < 0) return rc; } } if (table->entry_count) kfree(table->entries); table->entries = kcalloc(num_vlans, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = num_vlans; vlan = table->entries; for (i = 0; i < VLAN_N_VID; i++) { if (new_vlan[i].vlanid == VLAN_N_VID) continue; vlan[k++] = new_vlan[i]; } /* VLAN Retagging Table */ table = &priv->static_config.tables[BLK_IDX_RETAGGING]; retagging = table->entries; for (i = 0; i < table->entry_count; i++) { rc = sja1105_dynamic_config_write(priv, BLK_IDX_RETAGGING, i, &retagging[i], false); if (rc) return rc; } if (table->entry_count) kfree(table->entries); table->entries = kcalloc(num_retagging, table->ops->unpacked_entry_size, GFP_KERNEL); if (!table->entries) return -ENOMEM; table->entry_count = num_retagging; retagging = table->entries; for (i = 0; i < num_retagging; i++) { retagging[i] = new_retagging[i]; /* Update entry */ rc = sja1105_dynamic_config_write(priv, BLK_IDX_RETAGGING, i, &retagging[i], true); if (rc < 0) return rc; } return 0; } struct sja1105_crosschip_vlan { struct list_head list; u16 vid; bool untagged; int port; int other_port; struct dsa_8021q_context *other_ctx; }; struct sja1105_crosschip_switch { struct list_head list; struct dsa_8021q_context *other_ctx; }; static int sja1105_commit_pvid(struct sja1105_private *priv) { struct sja1105_bridge_vlan *v; struct list_head *vlan_list; int rc = 0; if (priv->vlan_state == SJA1105_VLAN_FILTERING_FULL) vlan_list = &priv->bridge_vlans; else vlan_list = &priv->dsa_8021q_vlans; list_for_each_entry(v, vlan_list, list) { if (v->pvid) { rc = sja1105_pvid_apply(priv, v->port, v->vid); if (rc) break; } } return rc; } static int sja1105_build_bridge_vlans(struct sja1105_private *priv, struct sja1105_vlan_lookup_entry *new_vlan) { struct sja1105_bridge_vlan *v; if (priv->vlan_state == SJA1105_VLAN_UNAWARE) return 0; list_for_each_entry(v, &priv->bridge_vlans, list) { int match = v->vid; new_vlan[match].vlanid = v->vid; new_vlan[match].vmemb_port |= BIT(v->port); new_vlan[match].vlan_bc |= BIT(v->port); if (!v->untagged) new_vlan[match].tag_port |= BIT(v->port); } return 0; } static int sja1105_build_dsa_8021q_vlans(struct sja1105_private *priv, struct sja1105_vlan_lookup_entry *new_vlan) { struct sja1105_bridge_vlan *v; if (priv->vlan_state == SJA1105_VLAN_FILTERING_FULL) return 0; list_for_each_entry(v, &priv->dsa_8021q_vlans, list) { int match = v->vid; new_vlan[match].vlanid = v->vid; new_vlan[match].vmemb_port |= BIT(v->port); new_vlan[match].vlan_bc |= BIT(v->port); if (!v->untagged) new_vlan[match].tag_port |= BIT(v->port); } return 0; } static int sja1105_build_subvlans(struct sja1105_private *priv, u16 subvlan_map[][DSA_8021Q_N_SUBVLAN], struct sja1105_vlan_lookup_entry *new_vlan, struct sja1105_retagging_entry *new_retagging, int *num_retagging) { struct sja1105_bridge_vlan *v; int k = *num_retagging; if (priv->vlan_state != SJA1105_VLAN_BEST_EFFORT) return 0; list_for_each_entry(v, &priv->bridge_vlans, list) { int upstream = dsa_upstream_port(priv->ds, v->port); int match, subvlan; u16 rx_vid; /* Only sub-VLANs on user ports need to be applied. * Bridge VLANs also include VLANs added automatically * by DSA on the CPU port. */ if (!dsa_is_user_port(priv->ds, v->port)) continue; subvlan = sja1105_find_subvlan(subvlan_map[v->port], v->vid); if (subvlan < 0) { subvlan = sja1105_find_free_subvlan(subvlan_map[v->port], v->pvid); if (subvlan < 0) { dev_err(priv->ds->dev, "No more free subvlans\n"); return -ENOSPC; } } rx_vid = dsa_8021q_rx_vid_subvlan(priv->ds, v->port, subvlan); /* @v->vid on @v->port needs to be retagged to @rx_vid * on @upstream. Assume @v->vid on @v->port and on * @upstream was already configured by the previous * iteration over bridge_vlans. */ match = rx_vid; new_vlan[match].vlanid = rx_vid; new_vlan[match].vmemb_port |= BIT(v->port); new_vlan[match].vmemb_port |= BIT(upstream); new_vlan[match].vlan_bc |= BIT(v->port); new_vlan[match].vlan_bc |= BIT(upstream); /* The "untagged" flag is set the same as for the * original VLAN */ if (!v->untagged) new_vlan[match].tag_port |= BIT(v->port); /* But it's always tagged towards the CPU */ new_vlan[match].tag_port |= BIT(upstream); /* The Retagging Table generates packet *clones* with * the new VLAN. This is a very odd hardware quirk * which we need to suppress by dropping the original * packet. * Deny egress of the original VLAN towards the CPU * port. This will force the switch to drop it, and * we'll see only the retagged packets. */ match = v->vid; new_vlan[match].vlan_bc &= ~BIT(upstream); /* And the retagging itself */ new_retagging[k].vlan_ing = v->vid; new_retagging[k].vlan_egr = rx_vid; new_retagging[k].ing_port = BIT(v->port); new_retagging[k].egr_port = BIT(upstream); if (k++ == SJA1105_MAX_RETAGGING_COUNT) { dev_err(priv->ds->dev, "No more retagging rules\n"); return -ENOSPC; } subvlan_map[v->port][subvlan] = v->vid; } *num_retagging = k; return 0; } /* Sadly, in crosschip scenarios where the CPU port is also the link to another * switch, we should retag backwards (the dsa_8021q vid to the original vid) on * the CPU port of neighbour switches. */ static int sja1105_build_crosschip_subvlans(struct sja1105_private *priv, struct sja1105_vlan_lookup_entry *new_vlan, struct sja1105_retagging_entry *new_retagging, int *num_retagging) { struct sja1105_crosschip_vlan *tmp, *pos; struct dsa_8021q_crosschip_link *c; struct sja1105_bridge_vlan *v, *w; struct list_head crosschip_vlans; int k = *num_retagging; int rc = 0; if (priv->vlan_state != SJA1105_VLAN_BEST_EFFORT) return 0; INIT_LIST_HEAD(&crosschip_vlans); list_for_each_entry(c, &priv->dsa_8021q_ctx->crosschip_links, list) { struct sja1105_private *other_priv = c->other_ctx->ds->priv; if (other_priv->vlan_state == SJA1105_VLAN_FILTERING_FULL) continue; /* Crosschip links are also added to the CPU ports. * Ignore those. */ if (!dsa_is_user_port(priv->ds, c->port)) continue; if (!dsa_is_user_port(c->other_ctx->ds, c->other_port)) continue; /* Search for VLANs on the remote port */ list_for_each_entry(v, &other_priv->bridge_vlans, list) { bool already_added = false; bool we_have_it = false; if (v->port != c->other_port) continue; /* If @v is a pvid on @other_ds, it does not need * re-retagging, because its SVL field is 0 and we * already allow that, via the dsa_8021q crosschip * links. */ if (v->pvid) continue; /* Search for the VLAN on our local port */ list_for_each_entry(w, &priv->bridge_vlans, list) { if (w->port == c->port && w->vid == v->vid) { we_have_it = true; break; } } if (!we_have_it) continue; list_for_each_entry(tmp, &crosschip_vlans, list) { if (tmp->vid == v->vid && tmp->untagged == v->untagged && tmp->port == c->port && tmp->other_port == v->port && tmp->other_ctx == c->other_ctx) { already_added = true; break; } } if (already_added) continue; tmp = kzalloc(sizeof(*tmp), GFP_KERNEL); if (!tmp) { dev_err(priv->ds->dev, "Failed to allocate memory\n"); rc = -ENOMEM; goto out; } tmp->vid = v->vid; tmp->port = c->port; tmp->other_port = v->port; tmp->other_ctx = c->other_ctx; tmp->untagged = v->untagged; list_add(&tmp->list, &crosschip_vlans); } } list_for_each_entry(tmp, &crosschip_vlans, list) { struct sja1105_private *other_priv = tmp->other_ctx->ds->priv; int upstream = dsa_upstream_port(priv->ds, tmp->port); int match, subvlan; u16 rx_vid; subvlan = sja1105_find_committed_subvlan(other_priv, tmp->other_port, tmp->vid); /* If this happens, it's a bug. The neighbour switch does not * have a subvlan for tmp->vid on tmp->other_port, but it * should, since we already checked for its vlan_state. */ if (WARN_ON(subvlan < 0)) { rc = -EINVAL; goto out; } rx_vid = dsa_8021q_rx_vid_subvlan(tmp->other_ctx->ds, tmp->other_port, subvlan); /* The @rx_vid retagged from @tmp->vid on * {@tmp->other_ds, @tmp->other_port} needs to be * re-retagged to @tmp->vid on the way back to us. * * Assume the original @tmp->vid is already configured * on this local switch, otherwise we wouldn't be * retagging its subvlan on the other switch in the * first place. We just need to add a reverse retagging * rule for @rx_vid and install @rx_vid on our ports. */ match = rx_vid; new_vlan[match].vlanid = rx_vid; new_vlan[match].vmemb_port |= BIT(tmp->port); new_vlan[match].vmemb_port |= BIT(upstream); /* The "untagged" flag is set the same as for the * original VLAN. And towards the CPU, it doesn't * really matter, because @rx_vid will only receive * traffic on that port. For consistency with other dsa_8021q * VLANs, we'll keep the CPU port tagged. */ if (!tmp->untagged) new_vlan[match].tag_port |= BIT(tmp->port); new_vlan[match].tag_port |= BIT(upstream); /* Deny egress of @rx_vid towards our front-panel port. * This will force the switch to drop it, and we'll see * only the re-retagged packets (having the original, * pre-initial-retagging, VLAN @tmp->vid). */ new_vlan[match].vlan_bc &= ~BIT(tmp->port); /* On reverse retagging, the same ingress VLAN goes to multiple * ports. So we have an opportunity to create composite rules * to not waste the limited space in the retagging table. */ k = sja1105_find_retagging_entry(new_retagging, *num_retagging, upstream, rx_vid, tmp->vid); if (k < 0) { if (*num_retagging == SJA1105_MAX_RETAGGING_COUNT) { dev_err(priv->ds->dev, "No more retagging rules\n"); rc = -ENOSPC; goto out; } k = (*num_retagging)++; } /* And the retagging itself */ new_retagging[k].vlan_ing = rx_vid; new_retagging[k].vlan_egr = tmp->vid; new_retagging[k].ing_port = BIT(upstream); new_retagging[k].egr_port |= BIT(tmp->port); } out: list_for_each_entry_safe(tmp, pos, &crosschip_vlans, list) { list_del(&tmp->list); kfree(tmp); } return rc; } static int sja1105_build_vlan_table(struct sja1105_private *priv, bool notify); static int sja1105_notify_crosschip_switches(struct sja1105_private *priv) { struct sja1105_crosschip_switch *s, *pos; struct list_head crosschip_switches; struct dsa_8021q_crosschip_link *c; int rc = 0; INIT_LIST_HEAD(&crosschip_switches); list_for_each_entry(c, &priv->dsa_8021q_ctx->crosschip_links, list) { bool already_added = false; list_for_each_entry(s, &crosschip_switches, list) { if (s->other_ctx == c->other_ctx) { already_added = true; break; } } if (already_added) continue; s = kzalloc(sizeof(*s), GFP_KERNEL); if (!s) { dev_err(priv->ds->dev, "Failed to allocate memory\n"); rc = -ENOMEM; goto out; } s->other_ctx = c->other_ctx; list_add(&s->list, &crosschip_switches); } list_for_each_entry(s, &crosschip_switches, list) { struct sja1105_private *other_priv = s->other_ctx->ds->priv; rc = sja1105_build_vlan_table(other_priv, false); if (rc) goto out; } out: list_for_each_entry_safe(s, pos, &crosschip_switches, list) { list_del(&s->list); kfree(s); } return rc; } static int sja1105_build_vlan_table(struct sja1105_private *priv, bool notify) { u16 subvlan_map[SJA1105_NUM_PORTS][DSA_8021Q_N_SUBVLAN]; struct sja1105_retagging_entry *new_retagging; struct sja1105_vlan_lookup_entry *new_vlan; struct sja1105_table *table; int i, num_retagging = 0; int rc; table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; new_vlan = kcalloc(VLAN_N_VID, table->ops->unpacked_entry_size, GFP_KERNEL); if (!new_vlan) return -ENOMEM; table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; new_retagging = kcalloc(SJA1105_MAX_RETAGGING_COUNT, table->ops->unpacked_entry_size, GFP_KERNEL); if (!new_retagging) { kfree(new_vlan); return -ENOMEM; } for (i = 0; i < VLAN_N_VID; i++) new_vlan[i].vlanid = VLAN_N_VID; for (i = 0; i < SJA1105_MAX_RETAGGING_COUNT; i++) new_retagging[i].vlan_ing = VLAN_N_VID; for (i = 0; i < priv->ds->num_ports; i++) sja1105_init_subvlan_map(subvlan_map[i]); /* Bridge VLANs */ rc = sja1105_build_bridge_vlans(priv, new_vlan); if (rc) goto out; /* VLANs necessary for dsa_8021q operation, given to us by tag_8021q.c: * - RX VLANs * - TX VLANs * - Crosschip links */ rc = sja1105_build_dsa_8021q_vlans(priv, new_vlan); if (rc) goto out; /* Private VLANs necessary for dsa_8021q operation, which we need to * determine on our own: * - Sub-VLANs * - Sub-VLANs of crosschip switches */ rc = sja1105_build_subvlans(priv, subvlan_map, new_vlan, new_retagging, &num_retagging); if (rc) goto out; rc = sja1105_build_crosschip_subvlans(priv, new_vlan, new_retagging, &num_retagging); if (rc) goto out; rc = sja1105_commit_vlans(priv, new_vlan, new_retagging, num_retagging); if (rc) goto out; rc = sja1105_commit_pvid(priv); if (rc) goto out; for (i = 0; i < priv->ds->num_ports; i++) sja1105_commit_subvlan_map(priv, i, subvlan_map[i]); if (notify) { rc = sja1105_notify_crosschip_switches(priv); if (rc) goto out; } out: kfree(new_vlan); kfree(new_retagging); return rc; } /* The TPID setting belongs to the General Parameters table, * which can only be partially reconfigured at runtime (and not the TPID). * So a switch reset is required. */ int sja1105_vlan_filtering(struct dsa_switch *ds, int port, bool enabled) { struct sja1105_l2_lookup_params_entry *l2_lookup_params; struct sja1105_general_params_entry *general_params; struct sja1105_private *priv = ds->priv; enum sja1105_vlan_state state; struct sja1105_table *table; struct sja1105_rule *rule; bool want_tagging; u16 tpid, tpid2; int rc; list_for_each_entry(rule, &priv->flow_block.rules, list) { if (rule->type == SJA1105_RULE_VL) { dev_err(ds->dev, "Cannot change VLAN filtering with active VL rules\n"); return -EBUSY; } } if (enabled) { /* Enable VLAN filtering. */ tpid = ETH_P_8021Q; tpid2 = ETH_P_8021AD; } else { /* Disable VLAN filtering. */ tpid = ETH_P_SJA1105; tpid2 = ETH_P_SJA1105; } for (port = 0; port < ds->num_ports; port++) { struct sja1105_port *sp = &priv->ports[port]; if (enabled) sp->xmit_tpid = priv->info->qinq_tpid; else sp->xmit_tpid = ETH_P_SJA1105; } if (!enabled) state = SJA1105_VLAN_UNAWARE; else if (priv->best_effort_vlan_filtering) state = SJA1105_VLAN_BEST_EFFORT; else state = SJA1105_VLAN_FILTERING_FULL; if (priv->vlan_state == state) return 0; priv->vlan_state = state; want_tagging = (state == SJA1105_VLAN_UNAWARE || state == SJA1105_VLAN_BEST_EFFORT); table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS]; general_params = table->entries; /* EtherType used to identify inner tagged (C-tag) VLAN traffic */ general_params->tpid = tpid; /* EtherType used to identify outer tagged (S-tag) VLAN traffic */ general_params->tpid2 = tpid2; /* When VLAN filtering is on, we need to at least be able to * decode management traffic through the "backup plan". */ general_params->incl_srcpt1 = enabled; general_params->incl_srcpt0 = enabled; want_tagging = priv->best_effort_vlan_filtering || !enabled; /* VLAN filtering => independent VLAN learning. * No VLAN filtering (or best effort) => shared VLAN learning. * * In shared VLAN learning mode, untagged traffic still gets * pvid-tagged, and the FDB table gets populated with entries * containing the "real" (pvid or from VLAN tag) VLAN ID. * However the switch performs a masked L2 lookup in the FDB, * effectively only looking up a frame's DMAC (and not VID) for the * forwarding decision. * * This is extremely convenient for us, because in modes with * vlan_filtering=0, dsa_8021q actually installs unique pvid's into * each front panel port. This is good for identification but breaks * learning badly - the VID of the learnt FDB entry is unique, aka * no frames coming from any other port are going to have it. So * for forwarding purposes, this is as though learning was broken * (all frames get flooded). */ table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS]; l2_lookup_params = table->entries; l2_lookup_params->shared_learn = want_tagging; sja1105_frame_memory_partitioning(priv); rc = sja1105_build_vlan_table(priv, false); if (rc) return rc; rc = sja1105_static_config_reload(priv, SJA1105_VLAN_FILTERING); if (rc) dev_err(ds->dev, "Failed to change VLAN Ethertype\n"); /* Switch port identification based on 802.1Q is only passable * if we are not under a vlan_filtering bridge. So make sure * the two configurations are mutually exclusive (of course, the * user may know better, i.e. best_effort_vlan_filtering). */ return sja1105_setup_8021q_tagging(ds, want_tagging); } /* Returns number of VLANs added (0 or 1) on success, * or a negative error code. */ static int sja1105_vlan_add_one(struct dsa_switch *ds, int port, u16 vid, u16 flags, struct list_head *vlan_list) { bool untagged = flags & BRIDGE_VLAN_INFO_UNTAGGED; bool pvid = flags & BRIDGE_VLAN_INFO_PVID; struct sja1105_bridge_vlan *v; list_for_each_entry(v, vlan_list, list) if (v->port == port && v->vid == vid && v->untagged == untagged && v->pvid == pvid) /* Already added */ return 0; v = kzalloc(sizeof(*v), GFP_KERNEL); if (!v) { dev_err(ds->dev, "Out of memory while storing VLAN\n"); return -ENOMEM; } v->port = port; v->vid = vid; v->untagged = untagged; v->pvid = pvid; list_add(&v->list, vlan_list); return 1; } /* Returns number of VLANs deleted (0 or 1) */ static int sja1105_vlan_del_one(struct dsa_switch *ds, int port, u16 vid, struct list_head *vlan_list) { struct sja1105_bridge_vlan *v, *n; list_for_each_entry_safe(v, n, vlan_list, list) { if (v->port == port && v->vid == vid) { list_del(&v->list); kfree(v); return 1; } } return 0; } static int sja1105_vlan_add(struct dsa_switch *ds, int port, const struct switchdev_obj_port_vlan *vlan) { struct sja1105_private *priv = ds->priv; bool vlan_table_changed = false; int rc; /* If the user wants best-effort VLAN filtering (aka vlan_filtering * bridge plus tagging), be sure to at least deny alterations to the * configuration done by dsa_8021q. */ if (priv->vlan_state != SJA1105_VLAN_FILTERING_FULL && vid_is_dsa_8021q(vlan->vid)) { dev_err(ds->dev, "Range 1024-3071 reserved for dsa_8021q operation\n"); return -EBUSY; } rc = sja1105_vlan_add_one(ds, port, vlan->vid, vlan->flags, &priv->bridge_vlans); if (rc < 0) return rc; if (rc > 0) vlan_table_changed = true; if (!vlan_table_changed) return 0; return sja1105_build_vlan_table(priv, true); } static int sja1105_vlan_del(struct dsa_switch *ds, int port, const struct switchdev_obj_port_vlan *vlan) { struct sja1105_private *priv = ds->priv; bool vlan_table_changed = false; int rc; rc = sja1105_vlan_del_one(ds, port, vlan->vid, &priv->bridge_vlans); if (rc > 0) vlan_table_changed = true; if (!vlan_table_changed) return 0; return sja1105_build_vlan_table(priv, true); } static int sja1105_dsa_8021q_vlan_add(struct dsa_switch *ds, int port, u16 vid, u16 flags) { struct sja1105_private *priv = ds->priv; int rc; rc = sja1105_vlan_add_one(ds, port, vid, flags, &priv->dsa_8021q_vlans); if (rc <= 0) return rc; return sja1105_build_vlan_table(priv, true); } static int sja1105_dsa_8021q_vlan_del(struct dsa_switch *ds, int port, u16 vid) { struct sja1105_private *priv = ds->priv; int rc; rc = sja1105_vlan_del_one(ds, port, vid, &priv->dsa_8021q_vlans); if (!rc) return 0; return sja1105_build_vlan_table(priv, true); } static const struct dsa_8021q_ops sja1105_dsa_8021q_ops = { .vlan_add = sja1105_dsa_8021q_vlan_add, .vlan_del = sja1105_dsa_8021q_vlan_del, }; /* The programming model for the SJA1105 switch is "all-at-once" via static * configuration tables. Some of these can be dynamically modified at runtime, * but not the xMII mode parameters table. * Furthermode, some PHYs may not have crystals for generating their clocks * (e.g. RMII). Instead, their 50MHz clock is supplied via the SJA1105 port's * ref_clk pin. So port clocking needs to be initialized early, before * connecting to PHYs is attempted, otherwise they won't respond through MDIO. * Setting correct PHY link speed does not matter now. * But dsa_slave_phy_setup is called later than sja1105_setup, so the PHY * bindings are not yet parsed by DSA core. We need to parse early so that we * can populate the xMII mode parameters table. */ static int sja1105_setup(struct dsa_switch *ds) { struct sja1105_dt_port ports[SJA1105_NUM_PORTS]; struct sja1105_private *priv = ds->priv; int rc; rc = sja1105_parse_dt(priv, ports); if (rc < 0) { dev_err(ds->dev, "Failed to parse DT: %d\n", rc); return rc; } /* Error out early if internal delays are required through DT * and we can't apply them. */ rc = sja1105_parse_rgmii_delays(priv, ports); if (rc < 0) { dev_err(ds->dev, "RGMII delay not supported\n"); return rc; } rc = sja1105_ptp_clock_register(ds); if (rc < 0) { dev_err(ds->dev, "Failed to register PTP clock: %d\n", rc); return rc; } /* Create and send configuration down to device */ rc = sja1105_static_config_load(priv, ports); if (rc < 0) { dev_err(ds->dev, "Failed to load static config: %d\n", rc); return rc; } /* Configure the CGU (PHY link modes and speeds) */ rc = sja1105_clocking_setup(priv); if (rc < 0) { dev_err(ds->dev, "Failed to configure MII clocking: %d\n", rc); return rc; } /* On SJA1105, VLAN filtering per se is always enabled in hardware. * The only thing we can do to disable it is lie about what the 802.1Q * EtherType is. * So it will still try to apply VLAN filtering, but all ingress * traffic (except frames received with EtherType of ETH_P_SJA1105) * will be internally tagged with a distorted VLAN header where the * TPID is ETH_P_SJA1105, and the VLAN ID is the port pvid. */ ds->vlan_filtering_is_global = true; /* Advertise the 8 egress queues */ ds->num_tx_queues = SJA1105_NUM_TC; ds->mtu_enforcement_ingress = true; rc = sja1105_devlink_setup(ds); if (rc < 0) return rc; /* The DSA/switchdev model brings up switch ports in standalone mode by * default, and that means vlan_filtering is 0 since they're not under * a bridge, so it's safe to set up switch tagging at this time. */ rtnl_lock(); rc = sja1105_setup_8021q_tagging(ds, true); rtnl_unlock(); return rc; } static void sja1105_teardown(struct dsa_switch *ds) { struct sja1105_private *priv = ds->priv; struct sja1105_bridge_vlan *v, *n; int port; for (port = 0; port < SJA1105_NUM_PORTS; port++) { struct sja1105_port *sp = &priv->ports[port]; if (!dsa_is_user_port(ds, port)) continue; if (sp->xmit_worker) kthread_destroy_worker(sp->xmit_worker); } sja1105_devlink_teardown(ds); sja1105_flower_teardown(ds); sja1105_tas_teardown(ds); sja1105_ptp_clock_unregister(ds); sja1105_static_config_free(&priv->static_config); list_for_each_entry_safe(v, n, &priv->dsa_8021q_vlans, list) { list_del(&v->list); kfree(v); } list_for_each_entry_safe(v, n, &priv->bridge_vlans, list) { list_del(&v->list); kfree(v); } } static int sja1105_port_enable(struct dsa_switch *ds, int port, struct phy_device *phy) { struct net_device *slave; if (!dsa_is_user_port(ds, port)) return 0; slave = dsa_to_port(ds, port)->slave; slave->features &= ~NETIF_F_HW_VLAN_CTAG_FILTER; return 0; } static void sja1105_port_disable(struct dsa_switch *ds, int port) { struct sja1105_private *priv = ds->priv; struct sja1105_port *sp = &priv->ports[port]; if (!dsa_is_user_port(ds, port)) return; kthread_cancel_work_sync(&sp->xmit_work); skb_queue_purge(&sp->xmit_queue); } static int sja1105_mgmt_xmit(struct dsa_switch *ds, int port, int slot, struct sk_buff *skb, bool takets) { struct sja1105_mgmt_entry mgmt_route = {0}; struct sja1105_private *priv = ds->priv; struct ethhdr *hdr; int timeout = 10; int rc; hdr = eth_hdr(skb); mgmt_route.macaddr = ether_addr_to_u64(hdr->h_dest); mgmt_route.destports = BIT(port); mgmt_route.enfport = 1; mgmt_route.tsreg = 0; mgmt_route.takets = takets; rc = sja1105_dynamic_config_write(priv, BLK_IDX_MGMT_ROUTE, slot, &mgmt_route, true); if (rc < 0) { kfree_skb(skb); return rc; } /* Transfer skb to the host port. */ dsa_enqueue_skb(skb, dsa_to_port(ds, port)->slave); /* Wait until the switch has processed the frame */ do { rc = sja1105_dynamic_config_read(priv, BLK_IDX_MGMT_ROUTE, slot, &mgmt_route); if (rc < 0) { dev_err_ratelimited(priv->ds->dev, "failed to poll for mgmt route\n"); continue; } /* UM10944: The ENFPORT flag of the respective entry is * cleared when a match is found. The host can use this * flag as an acknowledgment. */ cpu_relax(); } while (mgmt_route.enfport && --timeout); if (!timeout) { /* Clean up the management route so that a follow-up * frame may not match on it by mistake. * This is only hardware supported on P/Q/R/S - on E/T it is * a no-op and we are silently discarding the -EOPNOTSUPP. */ sja1105_dynamic_config_write(priv, BLK_IDX_MGMT_ROUTE, slot, &mgmt_route, false); dev_err_ratelimited(priv->ds->dev, "xmit timed out\n"); } return NETDEV_TX_OK; } #define work_to_port(work) \ container_of((work), struct sja1105_port, xmit_work) #define tagger_to_sja1105(t) \ container_of((t), struct sja1105_private, tagger_data) /* Deferred work is unfortunately necessary because setting up the management * route cannot be done from atomit context (SPI transfer takes a sleepable * lock on the bus) */ static void sja1105_port_deferred_xmit(struct kthread_work *work) { struct sja1105_port *sp = work_to_port(work); struct sja1105_tagger_data *tagger_data = sp->data; struct sja1105_private *priv = tagger_to_sja1105(tagger_data); int port = sp - priv->ports; struct sk_buff *skb; while ((skb = skb_dequeue(&sp->xmit_queue)) != NULL) { struct sk_buff *clone = DSA_SKB_CB(skb)->clone; mutex_lock(&priv->mgmt_lock); sja1105_mgmt_xmit(priv->ds, port, 0, skb, !!clone); /* The clone, if there, was made by dsa_skb_tx_timestamp */ if (clone) sja1105_ptp_txtstamp_skb(priv->ds, port, clone); mutex_unlock(&priv->mgmt_lock); } } /* The MAXAGE setting belongs to the L2 Forwarding Parameters table, * which cannot be reconfigured at runtime. So a switch reset is required. */ static int sja1105_set_ageing_time(struct dsa_switch *ds, unsigned int ageing_time) { struct sja1105_l2_lookup_params_entry *l2_lookup_params; struct sja1105_private *priv = ds->priv; struct sja1105_table *table; unsigned int maxage; table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS]; l2_lookup_params = table->entries; maxage = SJA1105_AGEING_TIME_MS(ageing_time); if (l2_lookup_params->maxage == maxage) return 0; l2_lookup_params->maxage = maxage; return sja1105_static_config_reload(priv, SJA1105_AGEING_TIME); } static int sja1105_change_mtu(struct dsa_switch *ds, int port, int new_mtu) { struct sja1105_l2_policing_entry *policing; struct sja1105_private *priv = ds->priv; new_mtu += VLAN_ETH_HLEN + ETH_FCS_LEN; if (dsa_is_cpu_port(ds, port)) new_mtu += VLAN_HLEN; policing = priv->static_config.tables[BLK_IDX_L2_POLICING].entries; if (policing[port].maxlen == new_mtu) return 0; policing[port].maxlen = new_mtu; return sja1105_static_config_reload(priv, SJA1105_BEST_EFFORT_POLICING); } static int sja1105_get_max_mtu(struct dsa_switch *ds, int port) { return 2043 - VLAN_ETH_HLEN - ETH_FCS_LEN; } static int sja1105_port_setup_tc(struct dsa_switch *ds, int port, enum tc_setup_type type, void *type_data) { switch (type) { case TC_SETUP_QDISC_TAPRIO: return sja1105_setup_tc_taprio(ds, port, type_data); case TC_SETUP_QDISC_CBS: return sja1105_setup_tc_cbs(ds, port, type_data); default: return -EOPNOTSUPP; } } /* We have a single mirror (@to) port, but can configure ingress and egress * mirroring on all other (@from) ports. * We need to allow mirroring rules only as long as the @to port is always the * same, and we need to unset the @to port from mirr_port only when there is no * mirroring rule that references it. */ static int sja1105_mirror_apply(struct sja1105_private *priv, int from, int to, bool ingress, bool enabled) { struct sja1105_general_params_entry *general_params; struct sja1105_mac_config_entry *mac; struct sja1105_table *table; bool already_enabled; u64 new_mirr_port; int rc; table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS]; general_params = table->entries; mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; already_enabled = (general_params->mirr_port != SJA1105_NUM_PORTS); if (already_enabled && enabled && general_params->mirr_port != to) { dev_err(priv->ds->dev, "Delete mirroring rules towards port %llu first\n", general_params->mirr_port); return -EBUSY; } new_mirr_port = to; if (!enabled) { bool keep = false; int port; /* Anybody still referencing mirr_port? */ for (port = 0; port < SJA1105_NUM_PORTS; port++) { if (mac[port].ing_mirr || mac[port].egr_mirr) { keep = true; break; } } /* Unset already_enabled for next time */ if (!keep) new_mirr_port = SJA1105_NUM_PORTS; } if (new_mirr_port != general_params->mirr_port) { general_params->mirr_port = new_mirr_port; rc = sja1105_dynamic_config_write(priv, BLK_IDX_GENERAL_PARAMS, 0, general_params, true); if (rc < 0) return rc; } if (ingress) mac[from].ing_mirr = enabled; else mac[from].egr_mirr = enabled; return sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, from, &mac[from], true); } static int sja1105_mirror_add(struct dsa_switch *ds, int port, struct dsa_mall_mirror_tc_entry *mirror, bool ingress) { return sja1105_mirror_apply(ds->priv, port, mirror->to_local_port, ingress, true); } static void sja1105_mirror_del(struct dsa_switch *ds, int port, struct dsa_mall_mirror_tc_entry *mirror) { sja1105_mirror_apply(ds->priv, port, mirror->to_local_port, mirror->ingress, false); } static int sja1105_port_policer_add(struct dsa_switch *ds, int port, struct dsa_mall_policer_tc_entry *policer) { struct sja1105_l2_policing_entry *policing; struct sja1105_private *priv = ds->priv; policing = priv->static_config.tables[BLK_IDX_L2_POLICING].entries; /* In hardware, every 8 microseconds the credit level is incremented by * the value of RATE bytes divided by 64, up to a maximum of SMAX * bytes. */ policing[port].rate = div_u64(512 * policer->rate_bytes_per_sec, 1000000); policing[port].smax = policer->burst; return sja1105_static_config_reload(priv, SJA1105_BEST_EFFORT_POLICING); } static void sja1105_port_policer_del(struct dsa_switch *ds, int port) { struct sja1105_l2_policing_entry *policing; struct sja1105_private *priv = ds->priv; policing = priv->static_config.tables[BLK_IDX_L2_POLICING].entries; policing[port].rate = SJA1105_RATE_MBPS(1000); policing[port].smax = 65535; sja1105_static_config_reload(priv, SJA1105_BEST_EFFORT_POLICING); } static int sja1105_port_set_learning(struct sja1105_private *priv, int port, bool enabled) { struct sja1105_mac_config_entry *mac; int rc; mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; mac[port].dyn_learn = !!(priv->learn_ena & BIT(port)); rc = sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port, &mac[port], true); if (rc) return rc; if (enabled) priv->learn_ena |= BIT(port); else priv->learn_ena &= ~BIT(port); return 0; } /* Common function for unicast and broadcast flood configuration. * Flooding is configured between each {ingress, egress} port pair, and since * the bridge's semantics are those of "egress flooding", it means we must * enable flooding towards this port from all ingress ports that are in the * same bridge. In practice, we just enable flooding from all possible ingress * ports regardless of whether they're in the same bridge or not, since the * reach_port configuration will not allow flooded frames to leak across * bridging domains anyway. */ static int sja1105_port_ucast_bcast_flood(struct sja1105_private *priv, int to, struct switchdev_brport_flags flags) { struct sja1105_l2_forwarding_entry *l2_fwd; int from, rc; l2_fwd = priv->static_config.tables[BLK_IDX_L2_FORWARDING].entries; for (from = 0; from < priv->ds->num_ports; from++) { if (dsa_is_unused_port(priv->ds, from)) continue; if (from == to) continue; /* Unicast */ if (flags.mask & BR_FLOOD) { if (flags.val & BR_FLOOD) l2_fwd[from].fl_domain |= BIT(to); else l2_fwd[from].fl_domain &= ~BIT(to); } /* Broadcast */ if (flags.mask & BR_BCAST_FLOOD) { if (flags.val & BR_BCAST_FLOOD) l2_fwd[from].bc_domain |= BIT(to); else l2_fwd[from].bc_domain &= ~BIT(to); } rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING, from, &l2_fwd[from], true); if (rc < 0) return rc; } return 0; } static int sja1105_port_mcast_flood(struct sja1105_private *priv, int to, struct switchdev_brport_flags flags, struct netlink_ext_ack *extack) { struct sja1105_l2_lookup_entry *l2_lookup; struct sja1105_table *table; int match; table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP]; l2_lookup = table->entries; for (match = 0; match < table->entry_count; match++) if (l2_lookup[match].macaddr == SJA1105_UNKNOWN_MULTICAST && l2_lookup[match].mask_macaddr == SJA1105_UNKNOWN_MULTICAST) break; if (match == table->entry_count) { NL_SET_ERR_MSG_MOD(extack, "Could not find FDB entry for unknown multicast"); return -ENOSPC; } if (flags.val & BR_MCAST_FLOOD) l2_lookup[match].destports |= BIT(to); else l2_lookup[match].destports &= ~BIT(to); return sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, l2_lookup[match].index, &l2_lookup[match], true); } static int sja1105_port_pre_bridge_flags(struct dsa_switch *ds, int port, struct switchdev_brport_flags flags, struct netlink_ext_ack *extack) { struct sja1105_private *priv = ds->priv; if (flags.mask & ~(BR_LEARNING | BR_FLOOD | BR_MCAST_FLOOD | BR_BCAST_FLOOD)) return -EINVAL; if (flags.mask & (BR_FLOOD | BR_MCAST_FLOOD) && !priv->info->can_limit_mcast_flood) { bool multicast = !!(flags.val & BR_MCAST_FLOOD); bool unicast = !!(flags.val & BR_FLOOD); if (unicast != multicast) { NL_SET_ERR_MSG_MOD(extack, "This chip cannot configure multicast flooding independently of unicast"); return -EINVAL; } } return 0; } static int sja1105_port_bridge_flags(struct dsa_switch *ds, int port, struct switchdev_brport_flags flags, struct netlink_ext_ack *extack) { struct sja1105_private *priv = ds->priv; int rc; if (flags.mask & BR_LEARNING) { bool learn_ena = !!(flags.val & BR_LEARNING); rc = sja1105_port_set_learning(priv, port, learn_ena); if (rc) return rc; } if (flags.mask & (BR_FLOOD | BR_BCAST_FLOOD)) { rc = sja1105_port_ucast_bcast_flood(priv, port, flags); if (rc) return rc; } /* For chips that can't offload BR_MCAST_FLOOD independently, there * is nothing to do here, we ensured the configuration is in sync by * offloading BR_FLOOD. */ if (flags.mask & BR_MCAST_FLOOD && priv->info->can_limit_mcast_flood) { rc = sja1105_port_mcast_flood(priv, port, flags, extack); if (rc) return rc; } return 0; } static const struct dsa_switch_ops sja1105_switch_ops = { .get_tag_protocol = sja1105_get_tag_protocol, .setup = sja1105_setup, .teardown = sja1105_teardown, .set_ageing_time = sja1105_set_ageing_time, .port_change_mtu = sja1105_change_mtu, .port_max_mtu = sja1105_get_max_mtu, .phylink_validate = sja1105_phylink_validate, .phylink_mac_link_state = sja1105_mac_pcs_get_state, .phylink_mac_config = sja1105_mac_config, .phylink_mac_link_up = sja1105_mac_link_up, .phylink_mac_link_down = sja1105_mac_link_down, .get_strings = sja1105_get_strings, .get_ethtool_stats = sja1105_get_ethtool_stats, .get_sset_count = sja1105_get_sset_count, .get_ts_info = sja1105_get_ts_info, .port_enable = sja1105_port_enable, .port_disable = sja1105_port_disable, .port_fdb_dump = sja1105_fdb_dump, .port_fdb_add = sja1105_fdb_add, .port_fdb_del = sja1105_fdb_del, .port_bridge_join = sja1105_bridge_join, .port_bridge_leave = sja1105_bridge_leave, .port_pre_bridge_flags = sja1105_port_pre_bridge_flags, .port_bridge_flags = sja1105_port_bridge_flags, .port_stp_state_set = sja1105_bridge_stp_state_set, .port_vlan_filtering = sja1105_vlan_filtering, .port_vlan_add = sja1105_vlan_add, .port_vlan_del = sja1105_vlan_del, .port_mdb_add = sja1105_mdb_add, .port_mdb_del = sja1105_mdb_del, .port_hwtstamp_get = sja1105_hwtstamp_get, .port_hwtstamp_set = sja1105_hwtstamp_set, .port_rxtstamp = sja1105_port_rxtstamp, .port_txtstamp = sja1105_port_txtstamp, .port_setup_tc = sja1105_port_setup_tc, .port_mirror_add = sja1105_mirror_add, .port_mirror_del = sja1105_mirror_del, .port_policer_add = sja1105_port_policer_add, .port_policer_del = sja1105_port_policer_del, .cls_flower_add = sja1105_cls_flower_add, .cls_flower_del = sja1105_cls_flower_del, .cls_flower_stats = sja1105_cls_flower_stats, .crosschip_bridge_join = sja1105_crosschip_bridge_join, .crosschip_bridge_leave = sja1105_crosschip_bridge_leave, .devlink_param_get = sja1105_devlink_param_get, .devlink_param_set = sja1105_devlink_param_set, .devlink_info_get = sja1105_devlink_info_get, }; static const struct of_device_id sja1105_dt_ids[]; static int sja1105_check_device_id(struct sja1105_private *priv) { const struct sja1105_regs *regs = priv->info->regs; u8 prod_id[SJA1105_SIZE_DEVICE_ID] = {0}; struct device *dev = &priv->spidev->dev; const struct of_device_id *match; u32 device_id; u64 part_no; int rc; rc = sja1105_xfer_u32(priv, SPI_READ, regs->device_id, &device_id, NULL); if (rc < 0) return rc; rc = sja1105_xfer_buf(priv, SPI_READ, regs->prod_id, prod_id, SJA1105_SIZE_DEVICE_ID); if (rc < 0) return rc; sja1105_unpack(prod_id, &part_no, 19, 4, SJA1105_SIZE_DEVICE_ID); for (match = sja1105_dt_ids; match->compatible[0]; match++) { const struct sja1105_info *info = match->data; /* Is what's been probed in our match table at all? */ if (info->device_id != device_id || info->part_no != part_no) continue; /* But is it what's in the device tree? */ if (priv->info->device_id != device_id || priv->info->part_no != part_no) { dev_warn(dev, "Device tree specifies chip %s but found %s, please fix it!\n", priv->info->name, info->name); /* It isn't. No problem, pick that up. */ priv->info = info; } return 0; } dev_err(dev, "Unexpected {device ID, part number}: 0x%x 0x%llx\n", device_id, part_no); return -ENODEV; } static int sja1105_probe(struct spi_device *spi) { struct sja1105_tagger_data *tagger_data; struct device *dev = &spi->dev; struct sja1105_private *priv; struct dsa_switch *ds; int rc, port; if (!dev->of_node) { dev_err(dev, "No DTS bindings for SJA1105 driver\n"); return -EINVAL; } priv = devm_kzalloc(dev, sizeof(struct sja1105_private), GFP_KERNEL); if (!priv) return -ENOMEM; /* Configure the optional reset pin and bring up switch */ priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); if (IS_ERR(priv->reset_gpio)) dev_dbg(dev, "reset-gpios not defined, ignoring\n"); else sja1105_hw_reset(priv->reset_gpio, 1, 1); /* Populate our driver private structure (priv) based on * the device tree node that was probed (spi) */ priv->spidev = spi; spi_set_drvdata(spi, priv); /* Configure the SPI bus */ spi->bits_per_word = 8; rc = spi_setup(spi); if (rc < 0) { dev_err(dev, "Could not init SPI\n"); return rc; } priv->info = of_device_get_match_data(dev); /* Detect hardware device */ rc = sja1105_check_device_id(priv); if (rc < 0) { dev_err(dev, "Device ID check failed: %d\n", rc); return rc; } dev_info(dev, "Probed switch chip: %s\n", priv->info->name); ds = devm_kzalloc(dev, sizeof(*ds), GFP_KERNEL); if (!ds) return -ENOMEM; ds->dev = dev; ds->num_ports = SJA1105_NUM_PORTS; ds->ops = &sja1105_switch_ops; ds->priv = priv; priv->ds = ds; tagger_data = &priv->tagger_data; mutex_init(&priv->ptp_data.lock); mutex_init(&priv->mgmt_lock); priv->dsa_8021q_ctx = devm_kzalloc(dev, sizeof(*priv->dsa_8021q_ctx), GFP_KERNEL); if (!priv->dsa_8021q_ctx) return -ENOMEM; priv->dsa_8021q_ctx->ops = &sja1105_dsa_8021q_ops; priv->dsa_8021q_ctx->proto = htons(ETH_P_8021Q); priv->dsa_8021q_ctx->ds = ds; INIT_LIST_HEAD(&priv->dsa_8021q_ctx->crosschip_links); INIT_LIST_HEAD(&priv->bridge_vlans); INIT_LIST_HEAD(&priv->dsa_8021q_vlans); sja1105_tas_setup(ds); sja1105_flower_setup(ds); rc = dsa_register_switch(priv->ds); if (rc) return rc; if (IS_ENABLED(CONFIG_NET_SCH_CBS)) { priv->cbs = devm_kcalloc(dev, priv->info->num_cbs_shapers, sizeof(struct sja1105_cbs_entry), GFP_KERNEL); if (!priv->cbs) return -ENOMEM; } /* Connections between dsa_port and sja1105_port */ for (port = 0; port < SJA1105_NUM_PORTS; port++) { struct sja1105_port *sp = &priv->ports[port]; struct dsa_port *dp = dsa_to_port(ds, port); struct net_device *slave; int subvlan; if (!dsa_is_user_port(ds, port)) continue; dp->priv = sp; sp->dp = dp; sp->data = tagger_data; slave = dp->slave; kthread_init_work(&sp->xmit_work, sja1105_port_deferred_xmit); sp->xmit_worker = kthread_create_worker(0, "%s_xmit", slave->name); if (IS_ERR(sp->xmit_worker)) { rc = PTR_ERR(sp->xmit_worker); dev_err(ds->dev, "failed to create deferred xmit thread: %d\n", rc); goto out; } skb_queue_head_init(&sp->xmit_queue); sp->xmit_tpid = ETH_P_SJA1105; for (subvlan = 0; subvlan < DSA_8021Q_N_SUBVLAN; subvlan++) sp->subvlan_map[subvlan] = VLAN_N_VID; } return 0; out: while (port-- > 0) { struct sja1105_port *sp = &priv->ports[port]; if (!dsa_is_user_port(ds, port)) continue; kthread_destroy_worker(sp->xmit_worker); } return rc; } static int sja1105_remove(struct spi_device *spi) { struct sja1105_private *priv = spi_get_drvdata(spi); dsa_unregister_switch(priv->ds); return 0; } static const struct of_device_id sja1105_dt_ids[] = { { .compatible = "nxp,sja1105e", .data = &sja1105e_info }, { .compatible = "nxp,sja1105t", .data = &sja1105t_info }, { .compatible = "nxp,sja1105p", .data = &sja1105p_info }, { .compatible = "nxp,sja1105q", .data = &sja1105q_info }, { .compatible = "nxp,sja1105r", .data = &sja1105r_info }, { .compatible = "nxp,sja1105s", .data = &sja1105s_info }, { /* sentinel */ }, }; MODULE_DEVICE_TABLE(of, sja1105_dt_ids); static struct spi_driver sja1105_driver = { .driver = { .name = "sja1105", .owner = THIS_MODULE, .of_match_table = of_match_ptr(sja1105_dt_ids), }, .probe = sja1105_probe, .remove = sja1105_remove, }; module_spi_driver(sja1105_driver); MODULE_AUTHOR("Vladimir Oltean "); MODULE_AUTHOR("Georg Waibel "); MODULE_DESCRIPTION("SJA1105 Driver"); MODULE_LICENSE("GPL v2");