From 61b64abd399fa4b15ac649ad93b453d2a8569314 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Thu, 7 May 2015 09:52:21 -0500 Subject: PCI/MSI: Rename msi_set_enable(), msix_clear_and_set_ctrl() Rename msi_set_enable() to pci_msi_set_enable() and msix_clear_and_set_ctrl() to pci_msix_clear_and_set_ctrl(). No functional change. [bhelgaas: changelog, split into separate patch] Signed-off-by: Michael S. Tsirkin Signed-off-by: Bjorn Helgaas Reviewed-by: Fam Zheng --- drivers/pci/msi.c | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/msi.c b/drivers/pci/msi.c index c3e7dfcf9ff5..6cd366058ec4 100644 --- a/drivers/pci/msi.c +++ b/drivers/pci/msi.c @@ -185,7 +185,7 @@ void __weak arch_restore_msi_irqs(struct pci_dev *dev) return default_restore_msi_irqs(dev); } -static void msi_set_enable(struct pci_dev *dev, int enable) +static void pci_msi_set_enable(struct pci_dev *dev, int enable) { u16 control; @@ -196,7 +196,7 @@ static void msi_set_enable(struct pci_dev *dev, int enable) pci_write_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, control); } -static void msix_clear_and_set_ctrl(struct pci_dev *dev, u16 clear, u16 set) +static void pci_msix_clear_and_set_ctrl(struct pci_dev *dev, u16 clear, u16 set) { u16 ctrl; @@ -452,7 +452,7 @@ static void __pci_restore_msi_state(struct pci_dev *dev) entry = irq_get_msi_desc(dev->irq); pci_intx_for_msi(dev, 0); - msi_set_enable(dev, 0); + pci_msi_set_enable(dev, 0); arch_restore_msi_irqs(dev); pci_read_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, &control); @@ -473,14 +473,14 @@ static void __pci_restore_msix_state(struct pci_dev *dev) /* route the table */ pci_intx_for_msi(dev, 0); - msix_clear_and_set_ctrl(dev, 0, + pci_msix_clear_and_set_ctrl(dev, 0, PCI_MSIX_FLAGS_ENABLE | PCI_MSIX_FLAGS_MASKALL); arch_restore_msi_irqs(dev); list_for_each_entry(entry, &dev->msi_list, list) msix_mask_irq(entry, entry->masked); - msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_MASKALL, 0); + pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_MASKALL, 0); } void pci_restore_msi_state(struct pci_dev *dev) @@ -647,7 +647,7 @@ static int msi_capability_init(struct pci_dev *dev, int nvec) int ret; unsigned mask; - msi_set_enable(dev, 0); /* Disable MSI during set up */ + pci_msi_set_enable(dev, 0); /* Disable MSI during set up */ entry = msi_setup_entry(dev, nvec); if (!entry) @@ -683,7 +683,7 @@ static int msi_capability_init(struct pci_dev *dev, int nvec) /* Set MSI enabled bits */ pci_intx_for_msi(dev, 0); - msi_set_enable(dev, 1); + pci_msi_set_enable(dev, 1); dev->msi_enabled = 1; dev->irq = entry->irq; @@ -775,7 +775,7 @@ static int msix_capability_init(struct pci_dev *dev, void __iomem *base; /* Ensure MSI-X is disabled while it is set up */ - msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0); + pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0); pci_read_config_word(dev, dev->msix_cap + PCI_MSIX_FLAGS, &control); /* Request & Map MSI-X table region */ @@ -801,7 +801,7 @@ static int msix_capability_init(struct pci_dev *dev, * MSI-X registers. We need to mask all the vectors to prevent * interrupts coming in before they're fully set up. */ - msix_clear_and_set_ctrl(dev, 0, + pci_msix_clear_and_set_ctrl(dev, 0, PCI_MSIX_FLAGS_MASKALL | PCI_MSIX_FLAGS_ENABLE); msix_program_entries(dev, entries); @@ -814,7 +814,7 @@ static int msix_capability_init(struct pci_dev *dev, pci_intx_for_msi(dev, 0); dev->msix_enabled = 1; - msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_MASKALL, 0); + pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_MASKALL, 0); return 0; @@ -919,7 +919,7 @@ void pci_msi_shutdown(struct pci_dev *dev) BUG_ON(list_empty(&dev->msi_list)); desc = list_first_entry(&dev->msi_list, struct msi_desc, list); - msi_set_enable(dev, 0); + pci_msi_set_enable(dev, 0); pci_intx_for_msi(dev, 1); dev->msi_enabled = 0; @@ -1027,7 +1027,7 @@ void pci_msix_shutdown(struct pci_dev *dev) __pci_msix_desc_mask_irq(entry, 1); } - msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0); + pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0); pci_intx_for_msi(dev, 1); dev->msix_enabled = 0; } @@ -1069,11 +1069,11 @@ void pci_msi_init_pci_dev(struct pci_dev *dev) */ dev->msi_cap = pci_find_capability(dev, PCI_CAP_ID_MSI); if (dev->msi_cap) - msi_set_enable(dev, 0); + pci_msi_set_enable(dev, 0); dev->msix_cap = pci_find_capability(dev, PCI_CAP_ID_MSIX); if (dev->msix_cap) - msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0); + pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0); } /** -- cgit v1.2.3 From 6a25f5e35ab742380742ebf2033f6d53518219db Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Thu, 7 May 2015 09:52:21 -0500 Subject: PCI/MSI: Export pci_msi_set_enable(), pci_msix_clear_and_set_ctrl() Move pci_msi_set_enable() and pci_msix_clear_and_set_ctrl() to drivers/pci/pci.h so they're available even when MSI isn't configured into the kernel. No functional change. [bhelgaas: changelog, split into separate patch] Signed-off-by: Michael S. Tsirkin Signed-off-by: Bjorn Helgaas Reviewed-by: Fam Zheng --- drivers/pci/msi.c | 21 --------------------- drivers/pci/pci.h | 21 +++++++++++++++++++++ 2 files changed, 21 insertions(+), 21 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/msi.c b/drivers/pci/msi.c index 6cd366058ec4..9942f6827a4a 100644 --- a/drivers/pci/msi.c +++ b/drivers/pci/msi.c @@ -185,27 +185,6 @@ void __weak arch_restore_msi_irqs(struct pci_dev *dev) return default_restore_msi_irqs(dev); } -static void pci_msi_set_enable(struct pci_dev *dev, int enable) -{ - u16 control; - - pci_read_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, &control); - control &= ~PCI_MSI_FLAGS_ENABLE; - if (enable) - control |= PCI_MSI_FLAGS_ENABLE; - pci_write_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, control); -} - -static void pci_msix_clear_and_set_ctrl(struct pci_dev *dev, u16 clear, u16 set) -{ - u16 ctrl; - - pci_read_config_word(dev, dev->msix_cap + PCI_MSIX_FLAGS, &ctrl); - ctrl &= ~clear; - ctrl |= set; - pci_write_config_word(dev, dev->msix_cap + PCI_MSIX_FLAGS, ctrl); -} - static inline __attribute_const__ u32 msi_mask(unsigned x) { /* Don't shift by >= width of type */ diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h index 9bd762c237ab..6f04d1ea2bcb 100644 --- a/drivers/pci/pci.h +++ b/drivers/pci/pci.h @@ -146,6 +146,27 @@ static inline void pci_no_msi(void) { } static inline void pci_msi_init_pci_dev(struct pci_dev *dev) { } #endif +static inline void pci_msi_set_enable(struct pci_dev *dev, int enable) +{ + u16 control; + + pci_read_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, &control); + control &= ~PCI_MSI_FLAGS_ENABLE; + if (enable) + control |= PCI_MSI_FLAGS_ENABLE; + pci_write_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, control); +} + +static inline void pci_msix_clear_and_set_ctrl(struct pci_dev *dev, u16 clear, u16 set) +{ + u16 ctrl; + + pci_read_config_word(dev, dev->msix_cap + PCI_MSIX_FLAGS, &ctrl); + ctrl &= ~clear; + ctrl |= set; + pci_write_config_word(dev, dev->msix_cap + PCI_MSIX_FLAGS, ctrl); +} + void pci_realloc_get_opt(char *); static inline int pci_no_d1d2(struct pci_dev *dev) -- cgit v1.2.3 From 1851617cd2da9cc53cdc1738f4148f4f042c0e56 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Thu, 7 May 2015 09:52:21 -0500 Subject: PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI If we enable MSI, then kexec a new kernel, the new kernel may receive MSIs it is not prepared for. Commit d5dea7d95c48 ("PCI: msi: Disable msi interrupts when we initialize a pci device") prevents this, but only if the new kernel is built with CONFIG_PCI_MSI=y. Move the "disable MSI" functionality from drivers/pci/msi.c to a new pci_msi_setup_pci_dev() in drivers/pci/probe.c so we can disable MSIs when we enumerate devices even if the kernel doesn't include full MSI support. [bhelgaas: changelog, disable MSIs in pci_setup_device(), put pci_msi_setup_pci_dev() at its final destination] Signed-off-by: Michael S. Tsirkin Signed-off-by: Bjorn Helgaas --- drivers/pci/msi.c | 12 ------------ drivers/pci/probe.c | 18 ++++++++++++++++++ 2 files changed, 18 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/msi.c b/drivers/pci/msi.c index 9942f6827a4a..f66be868ad21 100644 --- a/drivers/pci/msi.c +++ b/drivers/pci/msi.c @@ -1041,18 +1041,6 @@ EXPORT_SYMBOL(pci_msi_enabled); void pci_msi_init_pci_dev(struct pci_dev *dev) { INIT_LIST_HEAD(&dev->msi_list); - - /* Disable the msi hardware to avoid screaming interrupts - * during boot. This is the power on reset default so - * usually this should be a noop. - */ - dev->msi_cap = pci_find_capability(dev, PCI_CAP_ID_MSI); - if (dev->msi_cap) - pci_msi_set_enable(dev, 0); - - dev->msix_cap = pci_find_capability(dev, PCI_CAP_ID_MSIX); - if (dev->msix_cap) - pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0); } /** diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 6675a7a1b9fc..a9c5e63049a5 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -1085,6 +1085,22 @@ int pci_cfg_space_size(struct pci_dev *dev) #define LEGACY_IO_RESOURCE (IORESOURCE_IO | IORESOURCE_PCI_FIXED) +static void pci_msi_setup_pci_dev(struct pci_dev *dev) +{ + /* + * Disable the MSI hardware to avoid screaming interrupts + * during boot. This is the power on reset default so + * usually this should be a noop. + */ + dev->msi_cap = pci_find_capability(dev, PCI_CAP_ID_MSI); + if (dev->msi_cap) + pci_msi_set_enable(dev, 0); + + dev->msix_cap = pci_find_capability(dev, PCI_CAP_ID_MSIX); + if (dev->msix_cap) + pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0); +} + /** * pci_setup_device - fill in class and map information of a device * @dev: the device structure to fill @@ -1140,6 +1156,8 @@ int pci_setup_device(struct pci_dev *dev) /* "Unknown power state" */ dev->current_state = PCI_UNKNOWN; + pci_msi_setup_pci_dev(dev); + /* Early fixups, before probing the BARs */ pci_fixup_device(pci_fixup_early, dev); /* device class may be changed after fixup */ -- cgit v1.2.3 From c1f4d88abda3c6894d4027f85f640641b0ad3597 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Thu, 7 May 2015 09:52:21 -0500 Subject: virtio_pci: drop pci_msi_off() call during probe The PCI core now disables MSI and MSI-X for all devices during enumeration regardless of CONFIG_PCI_MSI. Remove device-specific code to disable MSI/MSI-X. Signed-off-by: Michael S. Tsirkin Signed-off-by: Bjorn Helgaas --- drivers/virtio/virtio_pci_common.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'drivers') diff --git a/drivers/virtio/virtio_pci_common.c b/drivers/virtio/virtio_pci_common.c index e894eb278d83..806bb2c2e382 100644 --- a/drivers/virtio/virtio_pci_common.c +++ b/drivers/virtio/virtio_pci_common.c @@ -501,9 +501,6 @@ static int virtio_pci_probe(struct pci_dev *pci_dev, INIT_LIST_HEAD(&vp_dev->virtqueues); spin_lock_init(&vp_dev->lock); - /* Disable MSI/MSIX to bring device to a known good state. */ - pci_msi_off(pci_dev); - /* enable the device */ rc = pci_enable_device(pci_dev); if (rc) -- cgit v1.2.3 From 8c9bb608e8ac6fef829a629aa46a5238fad272a4 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Thu, 7 May 2015 09:52:22 -0500 Subject: ntb: Drop pci_msi_off() call during probe The PCI core now disables MSI and MSI-X for all devices during enumeration regardless of CONFIG_PCI_MSI. Remove device-specific code to disable MSI/MSI-X. Signed-off-by: Michael S. Tsirkin Signed-off-by: Bjorn Helgaas --- drivers/ntb/ntb_hw.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/ntb/ntb_hw.c b/drivers/ntb/ntb_hw.c index cd29b1038c5e..8225cbcd6eb8 100644 --- a/drivers/ntb/ntb_hw.c +++ b/drivers/ntb/ntb_hw.c @@ -1313,8 +1313,6 @@ static int ntb_setup_intx(struct ntb_device *ndev) struct pci_dev *pdev = ndev->pdev; int rc; - pci_msi_off(pdev); - /* Verify intx is enabled */ pci_intx(pdev, 1); -- cgit v1.2.3 From 96803199b774e0bdc5910d63be5839c4460bd856 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Thu, 7 May 2015 09:52:22 -0500 Subject: PCI/MSI: Drop pci_msi_off() calls from quirks The PCI core now disables MSI and MSI-X for all devices during enumeration regardless of CONFIG_PCI_MSI. Remove device-specific code to disable MSI/MSI-X. Signed-off-by: Michael S. Tsirkin Signed-off-by: Bjorn Helgaas --- drivers/pci/quirks.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index c6dc1dfd25d5..00b106fc0b69 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -1600,7 +1600,6 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_a static void quirk_pcie_mch(struct pci_dev *pdev) { - pci_msi_off(pdev); pdev->no_msi = 1; } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch); @@ -1614,7 +1613,6 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quir */ static void quirk_pcie_pxh(struct pci_dev *dev) { - pci_msi_off(dev); dev->no_msi = 1; dev_warn(&dev->dev, "PXH quirk detected; SHPC device MSI disabled\n"); } -- cgit v1.2.3 From c6201cd8513db2db54b248a862672849ed9ccb82 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Thu, 7 May 2015 09:52:22 -0500 Subject: PCI/MSI: Remove unused pci_msi_off() pci_msi_off() is unused, so remove it. Removes the exported symbol pci_msi_off(). Signed-off-by: Bjorn Helgaas --- drivers/pci/pci.c | 33 --------------------------------- 1 file changed, 33 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index acc4b6ef78c4..687af7264406 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -3101,39 +3101,6 @@ bool pci_check_and_unmask_intx(struct pci_dev *dev) } EXPORT_SYMBOL_GPL(pci_check_and_unmask_intx); -/** - * pci_msi_off - disables any MSI or MSI-X capabilities - * @dev: the PCI device to operate on - * - * If you want to use MSI, see pci_enable_msi() and friends. - * This is a lower-level primitive that allows us to disable - * MSI operation at the device level. - */ -void pci_msi_off(struct pci_dev *dev) -{ - int pos; - u16 control; - - /* - * This looks like it could go in msi.c, but we need it even when - * CONFIG_PCI_MSI=n. For the same reason, we can't use - * dev->msi_cap or dev->msix_cap here. - */ - pos = pci_find_capability(dev, PCI_CAP_ID_MSI); - if (pos) { - pci_read_config_word(dev, pos + PCI_MSI_FLAGS, &control); - control &= ~PCI_MSI_FLAGS_ENABLE; - pci_write_config_word(dev, pos + PCI_MSI_FLAGS, control); - } - pos = pci_find_capability(dev, PCI_CAP_ID_MSIX); - if (pos) { - pci_read_config_word(dev, pos + PCI_MSIX_FLAGS, &control); - control &= ~PCI_MSIX_FLAGS_ENABLE; - pci_write_config_word(dev, pos + PCI_MSIX_FLAGS, control); - } -} -EXPORT_SYMBOL_GPL(pci_msi_off); - int pci_set_dma_max_seg_size(struct pci_dev *dev, unsigned int size) { return dma_set_max_seg_size(&dev->dev, size); -- cgit v1.2.3 From dca230d162e27386d2ff24438ef56c645e55bf44 Mon Sep 17 00:00:00 2001 From: Alex Williamson Date: Fri, 1 May 2015 13:20:13 -0600 Subject: PCI: Add ACS quirks for Intel 9-series PCH root ports Intel confirms that 9-series chipset root ports provide ACS-equivalent isolation when configured via the existing Intel PCH ACS quirk setup. Signed-off-by: Alex Williamson Signed-off-by: Bjorn Helgaas Acked-by: Don Dugger --- drivers/pci/quirks.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index c6dc1dfd25d5..f126bd69396b 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -3740,6 +3740,8 @@ static const u16 pci_quirk_intel_pch_acs_ids[] = { /* Wellsburg (X99) PCH */ 0x8d10, 0x8d11, 0x8d12, 0x8d13, 0x8d14, 0x8d15, 0x8d16, 0x8d17, 0x8d18, 0x8d19, 0x8d1a, 0x8d1b, 0x8d1c, 0x8d1d, 0x8d1e, + /* Lynx Point (9 series) PCH */ + 0x8c90, 0x8c92, 0x8c94, 0x8c96, 0x8c98, 0x8c9a, 0x8c9c, 0x8c9e, }; static bool pci_quirk_intel_pch_acs_match(struct pci_dev *dev) -- cgit v1.2.3 From 5dbb4c6167229c8d4f528e8ec26699a7305000a3 Mon Sep 17 00:00:00 2001 From: Zhichang Yuan Date: Fri, 24 Apr 2015 17:05:09 +0800 Subject: of/pci: Fix pci_address_to_pio() conversion of CPU address to I/O port 41f8bba7f555 ("of/pci: Add pci_register_io_range() and pci_pio_to_address()") added support for systems with several I/O ranges described by OF bindings. It modified pci_address_to_pio() look up the io_range for a given CPU physical address, but the conversion was wrong. Fix the conversion of address to I/O port. [bhelgaas: changelog] Fixes: 41f8bba7f555 ("of/pci: Add pci_register_io_range() and pci_pio_to_address()") Signed-off-by: Zhichang Yuan Signed-off-by: Bjorn Helgaas Acked-by: Liviu Dudau CC: stable@vger.kernel.org # v3.18+ --- drivers/of/address.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/of/address.c b/drivers/of/address.c index 78a7dcbec7d8..6906a3f61bd8 100644 --- a/drivers/of/address.c +++ b/drivers/of/address.c @@ -765,7 +765,7 @@ unsigned long __weak pci_address_to_pio(phys_addr_t address) spin_lock(&io_range_lock); list_for_each_entry(res, &io_range_list, list) { if (address >= res->start && address < res->start + res->size) { - addr = res->start - address + offset; + addr = address - res->start + offset; break; } offset += res->size; -- cgit v1.2.3 From 5b0f073899c4b229a6c40186ca7b37569840948e Mon Sep 17 00:00:00 2001 From: Zhou Wang Date: Wed, 13 May 2015 14:44:34 +0800 Subject: PCI: designware: Add support for x8 links Add support for x8 links. Signed-off-by: Zhou Wang Signed-off-by: Bjorn Helgaas Acked-by: Jingoo Han Acked-by: Pratyush Anand --- drivers/pci/host/pcie-designware.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c index 2e9f84fdd9ce..4ce0aa5e8248 100644 --- a/drivers/pci/host/pcie-designware.c +++ b/drivers/pci/host/pcie-designware.c @@ -31,6 +31,7 @@ #define PORT_LINK_MODE_1_LANES (0x1 << 16) #define PORT_LINK_MODE_2_LANES (0x3 << 16) #define PORT_LINK_MODE_4_LANES (0x7 << 16) +#define PORT_LINK_MODE_8_LANES (0xf << 16) #define PCIE_LINK_WIDTH_SPEED_CONTROL 0x80C #define PORT_LOGIC_SPEED_CHANGE (0x1 << 17) @@ -38,6 +39,7 @@ #define PORT_LOGIC_LINK_WIDTH_1_LANES (0x1 << 8) #define PORT_LOGIC_LINK_WIDTH_2_LANES (0x2 << 8) #define PORT_LOGIC_LINK_WIDTH_4_LANES (0x4 << 8) +#define PORT_LOGIC_LINK_WIDTH_8_LANES (0x8 << 8) #define PCIE_MSI_ADDR_LO 0x820 #define PCIE_MSI_ADDR_HI 0x824 @@ -778,6 +780,9 @@ void dw_pcie_setup_rc(struct pcie_port *pp) case 4: val |= PORT_LINK_MODE_4_LANES; break; + case 8: + val |= PORT_LINK_MODE_8_LANES; + break; } dw_pcie_writel_rc(pp, val, PCIE_PORT_LINK_CONTROL); @@ -794,6 +799,9 @@ void dw_pcie_setup_rc(struct pcie_port *pp) case 4: val |= PORT_LOGIC_LINK_WIDTH_4_LANES; break; + case 8: + val |= PORT_LOGIC_LINK_WIDTH_8_LANES; + break; } dw_pcie_writel_rc(pp, val, PCIE_LINK_WIDTH_SPEED_CONTROL); -- cgit v1.2.3 From c1e02ceaf5739d32f092ac07bf886a0281ec40b1 Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens Date: Tue, 12 May 2015 23:23:00 +0200 Subject: PCI: iproc: Allow override of device tree IRQ mapping function The iProc core PCIe driver defaults to using of_irq_parse_and_map_pci() for IRQ mapping. Add iproc_pcie.map_irq so bus interfaces that don't use device tree can override this by supplying their own IRQ mapping function. [bhelgaas: changelog] Posting: http://lkml.kernel.org/r/1431465781-10753-1-git-send-email-hauke@hauke-m.de Signed-off-by: Hauke Mehrtens Signed-off-by: Bjorn Helgaas Reviewed-by: Ray Jui --- drivers/pci/host/pcie-iproc-platform.c | 2 ++ drivers/pci/host/pcie-iproc.c | 2 +- drivers/pci/host/pcie-iproc.h | 1 + 3 files changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pci/host/pcie-iproc-platform.c b/drivers/pci/host/pcie-iproc-platform.c index afad6c21fcfa..c8aa06f10d73 100644 --- a/drivers/pci/host/pcie-iproc-platform.c +++ b/drivers/pci/host/pcie-iproc-platform.c @@ -71,6 +71,8 @@ static int iproc_pcie_pltfm_probe(struct platform_device *pdev) pcie->resources = &res; + pcie->map_irq = of_irq_parse_and_map_pci; + ret = iproc_pcie_setup(pcie); if (ret) { dev_err(pcie->dev, "PCIe controller setup failed\n"); diff --git a/drivers/pci/host/pcie-iproc.c b/drivers/pci/host/pcie-iproc.c index 329e1b54528b..cef31f6a1242 100644 --- a/drivers/pci/host/pcie-iproc.c +++ b/drivers/pci/host/pcie-iproc.c @@ -229,7 +229,7 @@ int iproc_pcie_setup(struct iproc_pcie *pcie) pci_scan_child_bus(bus); pci_assign_unassigned_bus_resources(bus); - pci_fixup_irqs(pci_common_swizzle, of_irq_parse_and_map_pci); + pci_fixup_irqs(pci_common_swizzle, pcie->map_irq); pci_bus_add_devices(bus); return 0; diff --git a/drivers/pci/host/pcie-iproc.h b/drivers/pci/host/pcie-iproc.h index e28075ed1856..a333d4b7723a 100644 --- a/drivers/pci/host/pcie-iproc.h +++ b/drivers/pci/host/pcie-iproc.h @@ -34,6 +34,7 @@ struct iproc_pcie { struct pci_bus *root_bus; struct phy *phy; int irqs[IPROC_PCIE_MAX_NUM_IRQS]; + int (*map_irq)(const struct pci_dev *, u8, u8); }; int iproc_pcie_setup(struct iproc_pcie *pcie); -- cgit v1.2.3 From 4785ffbdc9b52e308e43b9e2dcc1dca44f056d76 Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens Date: Tue, 12 May 2015 23:23:01 +0200 Subject: PCI: iproc: Add BCMA PCIe driver MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This driver adds support for the PCIe 2.0 controller found on the BCMA bus. This controller can be found on (mostly) all Broadcom BCM470X / BCM5301X ARM SoCs. The driver found in the Broadcom SDK does some more stuff, like setting up some DMA memory areas, chaining MPS and MRRS to 512 and also some PHY changes like "improving" the PCIe jitter and doing some special initialization for the 3rd PCIe port. This was tested on a bcm4708 board with 2 PCIe ports and wireless cards connected to them. PCI_DOMAINS is needed by this driver, because normally there is more than one PCIe controller and without PCI_DOMAINS only the first controller gets registered. This controller gets 6 IRQs; the last one is trigged by all IRQ events. [bhelgaas: fix "GPLv2" MODULE_LICENSE typo] Signed-off-by: Hauke Mehrtens Signed-off-by: Bjorn Helgaas Acked-by: Rafał Miłecki Acked-by: Ray Jui --- drivers/pci/host/Kconfig | 11 ++++ drivers/pci/host/Makefile | 1 + drivers/pci/host/pcie-iproc-bcma.c | 112 +++++++++++++++++++++++++++++++++++++ 3 files changed, 124 insertions(+) create mode 100644 drivers/pci/host/pcie-iproc-bcma.c (limited to 'drivers') diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig index 1dfb567b3522..9ca90d2415f5 100644 --- a/drivers/pci/host/Kconfig +++ b/drivers/pci/host/Kconfig @@ -125,4 +125,15 @@ config PCIE_IPROC_PLATFORM Say Y here if you want to use the Broadcom iProc PCIe controller through the generic platform bus interface +config PCIE_IPROC_BCMA + bool "Broadcom iProc PCIe BCMA bus driver" + depends on ARCH_BCM_IPROC || (ARM && COMPILE_TEST) + select PCIE_IPROC + select BCMA + select PCI_DOMAINS + default ARCH_BCM_5301X + help + Say Y here if you want to use the Broadcom iProc PCIe controller + through the BCMA bus interface + endmenu diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile index f733b4e27642..2f7c36f08d6b 100644 --- a/drivers/pci/host/Makefile +++ b/drivers/pci/host/Makefile @@ -15,3 +15,4 @@ obj-$(CONFIG_PCI_LAYERSCAPE) += pci-layerscape.o obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o obj-$(CONFIG_PCIE_IPROC_PLATFORM) += pcie-iproc-platform.o +obj-$(CONFIG_PCIE_IPROC_BCMA) += pcie-iproc-bcma.o diff --git a/drivers/pci/host/pcie-iproc-bcma.c b/drivers/pci/host/pcie-iproc-bcma.c new file mode 100644 index 000000000000..32119af0fe6a --- /dev/null +++ b/drivers/pci/host/pcie-iproc-bcma.c @@ -0,0 +1,112 @@ +/* + * Copyright (C) 2015 Broadcom Corporation + * Copyright (C) 2015 Hauke Mehrtens + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "pcie-iproc.h" + + +/* NS: CLASS field is R/O, and set to wrong 0x200 value */ +static void bcma_pcie2_fixup_class(struct pci_dev *dev) +{ + dev->class = PCI_CLASS_BRIDGE_PCI << 8; +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0x8011, bcma_pcie2_fixup_class); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0x8012, bcma_pcie2_fixup_class); + +static int iproc_pcie_bcma_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) +{ + struct pci_sys_data *sys = dev->sysdata; + struct iproc_pcie *pcie = sys->private_data; + struct bcma_device *bdev = container_of(pcie->dev, struct bcma_device, dev); + + return bcma_core_irq(bdev, 5); +} + +static int iproc_pcie_bcma_probe(struct bcma_device *bdev) +{ + struct iproc_pcie *pcie; + LIST_HEAD(res); + struct resource res_mem; + int ret; + + pcie = devm_kzalloc(&bdev->dev, sizeof(*pcie), GFP_KERNEL); + if (!pcie) + return -ENOMEM; + + pcie->dev = &bdev->dev; + bcma_set_drvdata(bdev, pcie); + + pcie->base = bdev->io_addr; + + res_mem.start = bdev->addr_s[0]; + res_mem.end = bdev->addr_s[0] + SZ_128M - 1; + res_mem.name = "PCIe MEM space"; + res_mem.flags = IORESOURCE_MEM; + pci_add_resource(&res, &res_mem); + + pcie->resources = &res; + + pcie->map_irq = iproc_pcie_bcma_map_irq; + + ret = iproc_pcie_setup(pcie); + if (ret) { + dev_err(pcie->dev, "PCIe controller setup failed\n"); + return ret; + } + + return 0; +} + +static void iproc_pcie_bcma_remove(struct bcma_device *bdev) +{ + struct iproc_pcie *pcie = bcma_get_drvdata(bdev); + + iproc_pcie_remove(pcie); +} + +static const struct bcma_device_id iproc_pcie_bcma_table[] = { + BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_PCIEG2, BCMA_ANY_REV, BCMA_ANY_CLASS), + {}, +}; +MODULE_DEVICE_TABLE(bcma, iproc_pcie_bcma_table); + +static struct bcma_driver iproc_pcie_bcma_driver = { + .name = KBUILD_MODNAME, + .id_table = iproc_pcie_bcma_table, + .probe = iproc_pcie_bcma_probe, + .remove = iproc_pcie_bcma_remove, +}; + +static int __init iproc_pcie_bcma_init(void) +{ + return bcma_driver_register(&iproc_pcie_bcma_driver); +} +module_init(iproc_pcie_bcma_init); + +static void __exit iproc_pcie_bcma_exit(void) +{ + bcma_driver_unregister(&iproc_pcie_bcma_driver); +} +module_exit(iproc_pcie_bcma_exit); + +MODULE_AUTHOR("Hauke Mehrtens"); +MODULE_DESCRIPTION("Broadcom iProc PCIe BCMA driver"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3 From e127a04f222fc4ad958a9bca35100883b8b1373b Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Wed, 20 May 2015 12:13:05 -0500 Subject: PCI/ASPM: Drop __pci_disable_link_state() useless "force" parameter After 387d37577fdd ("PCI: Don't clear ASPM bits when the FADT declares it's unsupported"), the "force" parameter to __pci_disable_link_state() is always "false". Remove the "force" parameter and assume it's always false. Signed-off-by: Bjorn Helgaas --- drivers/pci/pcie/aspm.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c index 7d4fcdc512aa..f90d8f2f091d 100644 --- a/drivers/pci/pcie/aspm.c +++ b/drivers/pci/pcie/aspm.c @@ -714,8 +714,7 @@ void pcie_aspm_powersave_config_link(struct pci_dev *pdev) up_read(&pci_bus_sem); } -static void __pci_disable_link_state(struct pci_dev *pdev, int state, bool sem, - bool force) +static void __pci_disable_link_state(struct pci_dev *pdev, int state, bool sem) { struct pci_dev *parent = pdev->bus->self; struct pcie_link_state *link; @@ -737,7 +736,7 @@ static void __pci_disable_link_state(struct pci_dev *pdev, int state, bool sem, * a similar mechanism using "PciASPMOptOut", which is also * ignored in this situation. */ - if (aspm_disabled && !force) { + if (aspm_disabled) { dev_warn(&pdev->dev, "can't disable ASPM; OS doesn't have ASPM control\n"); return; } @@ -763,7 +762,7 @@ static void __pci_disable_link_state(struct pci_dev *pdev, int state, bool sem, void pci_disable_link_state_locked(struct pci_dev *pdev, int state) { - __pci_disable_link_state(pdev, state, false, false); + __pci_disable_link_state(pdev, state, false); } EXPORT_SYMBOL(pci_disable_link_state_locked); @@ -778,7 +777,7 @@ EXPORT_SYMBOL(pci_disable_link_state_locked); */ void pci_disable_link_state(struct pci_dev *pdev, int state) { - __pci_disable_link_state(pdev, state, true, false); + __pci_disable_link_state(pdev, state, true); } EXPORT_SYMBOL(pci_disable_link_state); -- cgit v1.2.3 From f9b8cd7c2710813746f86eec6bbf12c869504285 Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Tue, 19 May 2015 11:41:34 +0800 Subject: PCI/ASPM: Remove redundant PCIe port type checking We decide in alloc_pcie_link_state() whether to allocate a pcie_link_state for a device. After that, it's sufficient to check pdev->link_state. We don't need to check the PCIe port type again. Remove the redundant PCIe port type checking. [bhelgaas: changelog] Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas --- drivers/pci/pcie/aspm.c | 19 ++++--------------- 1 file changed, 4 insertions(+), 15 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c index f90d8f2f091d..4e1af7637501 100644 --- a/drivers/pci/pcie/aspm.c +++ b/drivers/pci/pcie/aspm.c @@ -675,10 +675,7 @@ void pcie_aspm_pm_state_change(struct pci_dev *pdev) { struct pcie_link_state *link = pdev->link_state; - if (aspm_disabled || !pci_is_pcie(pdev) || !link) - return; - if ((pci_pcie_type(pdev) != PCI_EXP_TYPE_ROOT_PORT) && - (pci_pcie_type(pdev) != PCI_EXP_TYPE_DOWNSTREAM)) + if (aspm_disabled || !link) return; /* * Devices changed PM state, we should recheck if latency @@ -696,16 +693,12 @@ void pcie_aspm_powersave_config_link(struct pci_dev *pdev) { struct pcie_link_state *link = pdev->link_state; - if (aspm_disabled || !pci_is_pcie(pdev) || !link) + if (aspm_disabled || !link) return; if (aspm_policy != POLICY_POWERSAVE) return; - if ((pci_pcie_type(pdev) != PCI_EXP_TYPE_ROOT_PORT) && - (pci_pcie_type(pdev) != PCI_EXP_TYPE_DOWNSTREAM)) - return; - down_read(&pci_bus_sem); mutex_lock(&aspm_lock); pcie_config_aspm_path(link); @@ -906,9 +899,7 @@ void pcie_aspm_create_sysfs_dev_files(struct pci_dev *pdev) { struct pcie_link_state *link_state = pdev->link_state; - if (!pci_is_pcie(pdev) || - (pci_pcie_type(pdev) != PCI_EXP_TYPE_ROOT_PORT && - pci_pcie_type(pdev) != PCI_EXP_TYPE_DOWNSTREAM) || !link_state) + if (!link_state) return; if (link_state->aspm_support) @@ -923,9 +914,7 @@ void pcie_aspm_remove_sysfs_dev_files(struct pci_dev *pdev) { struct pcie_link_state *link_state = pdev->link_state; - if (!pci_is_pcie(pdev) || - (pci_pcie_type(pdev) != PCI_EXP_TYPE_ROOT_PORT && - pci_pcie_type(pdev) != PCI_EXP_TYPE_DOWNSTREAM) || !link_state) + if (!link_state) return; if (link_state->aspm_support) -- cgit v1.2.3 From 63503c87f06e0f2c8c951cada81221c5500188d8 Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Thu, 30 Apr 2015 16:22:28 +0800 Subject: PCI: designware: Consolidate outbound iATU programming functions Currently, the outbound iATU programming functions are similar: the only difference is index, type, addr and size. Consolidate these functions into one. This saves about 1700 bytes in text: text data bss dec hex filename 9276 204 4 9484 250c pcie-designware.o-before 7532 204 4 7740 1e3c pcie-designware.o Signed-off-by: Jisheng Zhang Signed-off-by: Bjorn Helgaas Acked-by: Pratyush Anand --- drivers/pci/host/pcie-designware.c | 109 +++++++++++++------------------------ 1 file changed, 39 insertions(+), 70 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c index 4ce0aa5e8248..49a0945f5a1b 100644 --- a/drivers/pci/host/pcie-designware.c +++ b/drivers/pci/host/pcie-designware.c @@ -152,6 +152,21 @@ static int dw_pcie_wr_own_conf(struct pcie_port *pp, int where, int size, return ret; } +static void dw_pcie_prog_outbound_atu(struct pcie_port *pp, int index, + int type, u64 cpu_addr, u64 pci_addr, u32 size) +{ + dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | index, + PCIE_ATU_VIEWPORT); + dw_pcie_writel_rc(pp, lower_32_bits(cpu_addr), PCIE_ATU_LOWER_BASE); + dw_pcie_writel_rc(pp, upper_32_bits(cpu_addr), PCIE_ATU_UPPER_BASE); + dw_pcie_writel_rc(pp, lower_32_bits(cpu_addr + size - 1), + PCIE_ATU_LIMIT); + dw_pcie_writel_rc(pp, lower_32_bits(pci_addr), PCIE_ATU_LOWER_TARGET); + dw_pcie_writel_rc(pp, upper_32_bits(pci_addr), PCIE_ATU_UPPER_TARGET); + dw_pcie_writel_rc(pp, type, PCIE_ATU_CR1); + dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); +} + static struct irq_chip dw_msi_irq_chip = { .name = "PCI-MSI", .irq_enable = pci_msi_unmask_irq, @@ -517,68 +532,6 @@ int dw_pcie_host_init(struct pcie_port *pp) return 0; } -static void dw_pcie_prog_viewport_cfg0(struct pcie_port *pp, u32 busdev) -{ - /* Program viewport 0 : OUTBOUND : CFG0 */ - dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0, - PCIE_ATU_VIEWPORT); - dw_pcie_writel_rc(pp, pp->cfg0_mod_base, PCIE_ATU_LOWER_BASE); - dw_pcie_writel_rc(pp, (pp->cfg0_mod_base >> 32), PCIE_ATU_UPPER_BASE); - dw_pcie_writel_rc(pp, pp->cfg0_mod_base + pp->cfg0_size - 1, - PCIE_ATU_LIMIT); - dw_pcie_writel_rc(pp, busdev, PCIE_ATU_LOWER_TARGET); - dw_pcie_writel_rc(pp, 0, PCIE_ATU_UPPER_TARGET); - dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_CFG0, PCIE_ATU_CR1); - dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); -} - -static void dw_pcie_prog_viewport_cfg1(struct pcie_port *pp, u32 busdev) -{ - /* Program viewport 1 : OUTBOUND : CFG1 */ - dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1, - PCIE_ATU_VIEWPORT); - dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_CFG1, PCIE_ATU_CR1); - dw_pcie_writel_rc(pp, pp->cfg1_mod_base, PCIE_ATU_LOWER_BASE); - dw_pcie_writel_rc(pp, (pp->cfg1_mod_base >> 32), PCIE_ATU_UPPER_BASE); - dw_pcie_writel_rc(pp, pp->cfg1_mod_base + pp->cfg1_size - 1, - PCIE_ATU_LIMIT); - dw_pcie_writel_rc(pp, busdev, PCIE_ATU_LOWER_TARGET); - dw_pcie_writel_rc(pp, 0, PCIE_ATU_UPPER_TARGET); - dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); -} - -static void dw_pcie_prog_viewport_mem_outbound(struct pcie_port *pp) -{ - /* Program viewport 0 : OUTBOUND : MEM */ - dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0, - PCIE_ATU_VIEWPORT); - dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_MEM, PCIE_ATU_CR1); - dw_pcie_writel_rc(pp, pp->mem_mod_base, PCIE_ATU_LOWER_BASE); - dw_pcie_writel_rc(pp, (pp->mem_mod_base >> 32), PCIE_ATU_UPPER_BASE); - dw_pcie_writel_rc(pp, pp->mem_mod_base + pp->mem_size - 1, - PCIE_ATU_LIMIT); - dw_pcie_writel_rc(pp, pp->mem_bus_addr, PCIE_ATU_LOWER_TARGET); - dw_pcie_writel_rc(pp, upper_32_bits(pp->mem_bus_addr), - PCIE_ATU_UPPER_TARGET); - dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); -} - -static void dw_pcie_prog_viewport_io_outbound(struct pcie_port *pp) -{ - /* Program viewport 1 : OUTBOUND : IO */ - dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1, - PCIE_ATU_VIEWPORT); - dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_IO, PCIE_ATU_CR1); - dw_pcie_writel_rc(pp, pp->io_mod_base, PCIE_ATU_LOWER_BASE); - dw_pcie_writel_rc(pp, (pp->io_mod_base >> 32), PCIE_ATU_UPPER_BASE); - dw_pcie_writel_rc(pp, pp->io_mod_base + pp->io_size - 1, - PCIE_ATU_LIMIT); - dw_pcie_writel_rc(pp, pp->io_bus_addr, PCIE_ATU_LOWER_TARGET); - dw_pcie_writel_rc(pp, upper_32_bits(pp->io_bus_addr), - PCIE_ATU_UPPER_TARGET); - dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); -} - static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus, u32 devfn, int where, int size, u32 *val) { @@ -590,15 +543,23 @@ static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus, address = where & ~0x3; if (bus->parent->number == pp->root_bus_nr) { - dw_pcie_prog_viewport_cfg0(pp, busdev); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, + PCIE_ATU_TYPE_CFG0, pp->cfg0_mod_base, + busdev, pp->cfg0_size); ret = dw_pcie_cfg_read(pp->va_cfg0_base + address, where, size, val); - dw_pcie_prog_viewport_mem_outbound(pp); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, + PCIE_ATU_TYPE_MEM, pp->mem_mod_base, + pp->mem_bus_addr, pp->mem_size); } else { - dw_pcie_prog_viewport_cfg1(pp, busdev); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, + PCIE_ATU_TYPE_CFG1, pp->cfg1_mod_base, + busdev, pp->cfg1_size); ret = dw_pcie_cfg_read(pp->va_cfg1_base + address, where, size, val); - dw_pcie_prog_viewport_io_outbound(pp); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, + PCIE_ATU_TYPE_IO, pp->io_mod_base, + pp->io_bus_addr, pp->io_size); } return ret; @@ -615,15 +576,23 @@ static int dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus, address = where & ~0x3; if (bus->parent->number == pp->root_bus_nr) { - dw_pcie_prog_viewport_cfg0(pp, busdev); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, + PCIE_ATU_TYPE_CFG0, pp->cfg0_mod_base, + busdev, pp->cfg0_size); ret = dw_pcie_cfg_write(pp->va_cfg0_base + address, where, size, val); - dw_pcie_prog_viewport_mem_outbound(pp); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, + PCIE_ATU_TYPE_MEM, pp->mem_mod_base, + pp->mem_bus_addr, pp->mem_size); } else { - dw_pcie_prog_viewport_cfg1(pp, busdev); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, + PCIE_ATU_TYPE_CFG1, pp->cfg1_mod_base, + busdev, pp->cfg1_size); ret = dw_pcie_cfg_write(pp->va_cfg1_base + address, where, size, val); - dw_pcie_prog_viewport_io_outbound(pp); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, + PCIE_ATU_TYPE_IO, pp->io_mod_base, + pp->io_bus_addr, pp->io_size); } return ret; -- cgit v1.2.3 From 2d91b491d5be13602a73be789bb8a3c28d06b7f2 Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Thu, 30 Apr 2015 16:22:29 +0800 Subject: PCI: designware: Use iATU0 for cfg and IO, iATU1 for MEM Most transactions' type are cfg0 and MEM, so the current iATU usage is not balanced: iATU0 is hot while iATU1 is rarely used. Refactor the iATU usage so we use iATU0 for cfg and IO and iATU1 for MEM. This allocation idea comes from Minghuan Lian : [bhelgaas: use link with Message-ID] Link: http://lkml.kernel.org/r/1429091315-31891-3-git-send-email-Minghuan.Lian@freescale.com Signed-off-by: Jisheng Zhang Signed-off-by: Bjorn Helgaas Acked-by: Pratyush Anand --- drivers/pci/host/pcie-designware.c | 81 +++++++++++++++++++++----------------- 1 file changed, 45 insertions(+), 36 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c index 49a0945f5a1b..0dca08d66649 100644 --- a/drivers/pci/host/pcie-designware.c +++ b/drivers/pci/host/pcie-designware.c @@ -510,6 +510,11 @@ int dw_pcie_host_init(struct pcie_port *pp) if (pp->ops->host_init) pp->ops->host_init(pp); + if (!pp->ops->rd_other_conf) + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, + PCIE_ATU_TYPE_MEM, pp->mem_mod_base, + pp->mem_bus_addr, pp->mem_size); + dw_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0); /* program correct class for RC */ @@ -535,66 +540,70 @@ int dw_pcie_host_init(struct pcie_port *pp) static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus, u32 devfn, int where, int size, u32 *val) { - int ret = PCIBIOS_SUCCESSFUL; - u32 address, busdev; + int ret, type; + u32 address, busdev, cfg_size; + u64 cpu_addr; + void __iomem *va_cfg_base; busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) | PCIE_ATU_FUNC(PCI_FUNC(devfn)); address = where & ~0x3; if (bus->parent->number == pp->root_bus_nr) { - dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, - PCIE_ATU_TYPE_CFG0, pp->cfg0_mod_base, - busdev, pp->cfg0_size); - ret = dw_pcie_cfg_read(pp->va_cfg0_base + address, where, size, - val); - dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, - PCIE_ATU_TYPE_MEM, pp->mem_mod_base, - pp->mem_bus_addr, pp->mem_size); + type = PCIE_ATU_TYPE_CFG0; + cpu_addr = pp->cfg0_mod_base; + cfg_size = pp->cfg0_size; + va_cfg_base = pp->va_cfg0_base; } else { - dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, - PCIE_ATU_TYPE_CFG1, pp->cfg1_mod_base, - busdev, pp->cfg1_size); - ret = dw_pcie_cfg_read(pp->va_cfg1_base + address, where, size, - val); - dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, - PCIE_ATU_TYPE_IO, pp->io_mod_base, - pp->io_bus_addr, pp->io_size); + type = PCIE_ATU_TYPE_CFG1; + cpu_addr = pp->cfg1_mod_base; + cfg_size = pp->cfg1_size; + va_cfg_base = pp->va_cfg1_base; } + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, + type, cpu_addr, + busdev, cfg_size); + ret = dw_pcie_cfg_read(va_cfg_base + address, where, size, val); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, + PCIE_ATU_TYPE_IO, pp->io_mod_base, + pp->io_bus_addr, pp->io_size); + return ret; } static int dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus, u32 devfn, int where, int size, u32 val) { - int ret = PCIBIOS_SUCCESSFUL; - u32 address, busdev; + int ret, type; + u32 address, busdev, cfg_size; + u64 cpu_addr; + void __iomem *va_cfg_base; busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) | PCIE_ATU_FUNC(PCI_FUNC(devfn)); address = where & ~0x3; if (bus->parent->number == pp->root_bus_nr) { - dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, - PCIE_ATU_TYPE_CFG0, pp->cfg0_mod_base, - busdev, pp->cfg0_size); - ret = dw_pcie_cfg_write(pp->va_cfg0_base + address, where, size, - val); - dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, - PCIE_ATU_TYPE_MEM, pp->mem_mod_base, - pp->mem_bus_addr, pp->mem_size); + type = PCIE_ATU_TYPE_CFG0; + cpu_addr = pp->cfg0_mod_base; + cfg_size = pp->cfg0_size; + va_cfg_base = pp->va_cfg0_base; } else { - dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, - PCIE_ATU_TYPE_CFG1, pp->cfg1_mod_base, - busdev, pp->cfg1_size); - ret = dw_pcie_cfg_write(pp->va_cfg1_base + address, where, size, - val); - dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1, - PCIE_ATU_TYPE_IO, pp->io_mod_base, - pp->io_bus_addr, pp->io_size); + type = PCIE_ATU_TYPE_CFG1; + cpu_addr = pp->cfg1_mod_base; + cfg_size = pp->cfg1_size; + va_cfg_base = pp->va_cfg1_base; } + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, + type, cpu_addr, + busdev, cfg_size); + ret = dw_pcie_cfg_write(va_cfg_base + address, where, size, val); + dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0, + PCIE_ATU_TYPE_IO, pp->io_mod_base, + pp->io_bus_addr, pp->io_size); + return ret; } -- cgit v1.2.3 From e705c2959b06b9db184842852da619a0b1672bbc Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Tue, 19 May 2015 15:27:58 +0200 Subject: PCI: pciehp: Drop pointless ACPI-based "slot detection" check Jarod Wilson reports that ExpressCard hotplug doesn't work on HP ZBook G2. The problem turns out to be the ACPI-based "slot detection" code called from pciehp_probe() which uses questionable heuristics based on what ACPI objects are present for the PCIe port device to figure out whether to register a hotplug slot for that port. That code is used if there is at least one PCIe port having an ACPI device configuration object related to hotplug (such as _EJ0 or _RMV), and the Thunderbolt port on the ZBook has _RMV. Of course, Thunderbolt and PCIe native hotplug need not be mutually exclusive (as they aren't on the ZBook), so that rule is simply incorrect. Moreover, the ACPI-based "slot detection" check does not add any value if pciehp_probe() is called at all and the service type of the device object it has been called for is PCIE_PORT_SERVICE_HP, because PCIe hotplug services are only registered if the _OSC handshake in acpi_pci_root_add() allows the kernel to control the PCIe native hotplug feature. No more checks need to be carried out to decide whether or not to register a native PCIe hotlug slot in that case. For the above reasons, make pciehp_probe() check if it has been called for the right service type and drop the pointless ACPI-based "slot detection" check from it. Also remove the entire code whose only user is that check (the entire pciehp_acpi.c file goes away as a result) and drop function headers related to it from the internal pciehp header file. Link: http://lkml.kernel.org/r/1431632038-39917-1-git-send-email-jarod@redhat.com Link: https://bugzilla.kernel.org/show_bug.cgi?id=98581 Reported-by: Jarod Wilson Signed-off-by: Rafael J. Wysocki Signed-off-by: Bjorn Helgaas Reviewed-by: Jarod Wilson Tested-by: Jarod Wilson --- drivers/pci/hotplug/Makefile | 3 - drivers/pci/hotplug/pciehp.h | 17 ----- drivers/pci/hotplug/pciehp_acpi.c | 137 -------------------------------------- drivers/pci/hotplug/pciehp_core.c | 10 +-- 4 files changed, 3 insertions(+), 164 deletions(-) delete mode 100644 drivers/pci/hotplug/pciehp_acpi.c (limited to 'drivers') diff --git a/drivers/pci/hotplug/Makefile b/drivers/pci/hotplug/Makefile index 4a9aa08b08f1..b616e7588ff4 100644 --- a/drivers/pci/hotplug/Makefile +++ b/drivers/pci/hotplug/Makefile @@ -61,9 +61,6 @@ pciehp-objs := pciehp_core.o \ pciehp_ctrl.o \ pciehp_pci.o \ pciehp_hpc.o -ifdef CONFIG_ACPI -pciehp-objs += pciehp_acpi.o -endif shpchp-objs := shpchp_core.o \ shpchp_ctrl.o \ diff --git a/drivers/pci/hotplug/pciehp.h b/drivers/pci/hotplug/pciehp.h index b11521953485..ce4d12c4eff4 100644 --- a/drivers/pci/hotplug/pciehp.h +++ b/drivers/pci/hotplug/pciehp.h @@ -167,21 +167,4 @@ static inline const char *slot_name(struct slot *slot) return hotplug_slot_name(slot->hotplug_slot); } -#ifdef CONFIG_ACPI -#include - -void __init pciehp_acpi_slot_detection_init(void); -int pciehp_acpi_slot_detection_check(struct pci_dev *dev); - -static inline void pciehp_firmware_init(void) -{ - pciehp_acpi_slot_detection_init(); -} -#else -#define pciehp_firmware_init() do {} while (0) -static inline int pciehp_acpi_slot_detection_check(struct pci_dev *dev) -{ - return 0; -} -#endif /* CONFIG_ACPI */ #endif /* _PCIEHP_H */ diff --git a/drivers/pci/hotplug/pciehp_acpi.c b/drivers/pci/hotplug/pciehp_acpi.c deleted file mode 100644 index 93cc9266e8cb..000000000000 --- a/drivers/pci/hotplug/pciehp_acpi.c +++ /dev/null @@ -1,137 +0,0 @@ -/* - * ACPI related functions for PCI Express Hot Plug driver. - * - * Copyright (C) 2008 Kenji Kaneshige - * Copyright (C) 2008 Fujitsu Limited. - * - * All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or (at - * your option) any later version. - * - * This program is distributed in the hope that it will be useful, but - * WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or - * NON INFRINGEMENT. See the GNU General Public License for more - * details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * - */ - -#include -#include -#include -#include -#include -#include "pciehp.h" - -#define PCIEHP_DETECT_PCIE (0) -#define PCIEHP_DETECT_ACPI (1) -#define PCIEHP_DETECT_AUTO (2) -#define PCIEHP_DETECT_DEFAULT PCIEHP_DETECT_AUTO - -struct dummy_slot { - u32 number; - struct list_head list; -}; - -static int slot_detection_mode; -static char *pciehp_detect_mode; -module_param(pciehp_detect_mode, charp, 0444); -MODULE_PARM_DESC(pciehp_detect_mode, - "Slot detection mode: pcie, acpi, auto\n" - " pcie - Use PCIe based slot detection\n" - " acpi - Use ACPI for slot detection\n" - " auto(default) - Auto select mode. Use acpi option if duplicate\n" - " slot ids are found. Otherwise, use pcie option\n"); - -int pciehp_acpi_slot_detection_check(struct pci_dev *dev) -{ - if (slot_detection_mode != PCIEHP_DETECT_ACPI) - return 0; - if (acpi_pci_detect_ejectable(ACPI_HANDLE(&dev->dev))) - return 0; - return -ENODEV; -} - -static int __init parse_detect_mode(void) -{ - if (!pciehp_detect_mode) - return PCIEHP_DETECT_DEFAULT; - if (!strcmp(pciehp_detect_mode, "pcie")) - return PCIEHP_DETECT_PCIE; - if (!strcmp(pciehp_detect_mode, "acpi")) - return PCIEHP_DETECT_ACPI; - if (!strcmp(pciehp_detect_mode, "auto")) - return PCIEHP_DETECT_AUTO; - warn("bad specifier '%s' for pciehp_detect_mode. Use default\n", - pciehp_detect_mode); - return PCIEHP_DETECT_DEFAULT; -} - -static int __initdata dup_slot_id; -static int __initdata acpi_slot_detected; -static struct list_head __initdata dummy_slots = LIST_HEAD_INIT(dummy_slots); - -/* Dummy driver for duplicate name detection */ -static int __init dummy_probe(struct pcie_device *dev) -{ - u32 slot_cap; - acpi_handle handle; - struct dummy_slot *slot, *tmp; - struct pci_dev *pdev = dev->port; - - pcie_capability_read_dword(pdev, PCI_EXP_SLTCAP, &slot_cap); - slot = kzalloc(sizeof(*slot), GFP_KERNEL); - if (!slot) - return -ENOMEM; - slot->number = (slot_cap & PCI_EXP_SLTCAP_PSN) >> 19; - list_for_each_entry(tmp, &dummy_slots, list) { - if (tmp->number == slot->number) - dup_slot_id++; - } - list_add_tail(&slot->list, &dummy_slots); - handle = ACPI_HANDLE(&pdev->dev); - if (!acpi_slot_detected && acpi_pci_detect_ejectable(handle)) - acpi_slot_detected = 1; - return -ENODEV; /* dummy driver always returns error */ -} - -static struct pcie_port_service_driver __initdata dummy_driver = { - .name = "pciehp_dummy", - .port_type = PCIE_ANY_PORT, - .service = PCIE_PORT_SERVICE_HP, - .probe = dummy_probe, -}; - -static int __init select_detection_mode(void) -{ - struct dummy_slot *slot, *tmp; - - if (pcie_port_service_register(&dummy_driver)) - return PCIEHP_DETECT_ACPI; - pcie_port_service_unregister(&dummy_driver); - list_for_each_entry_safe(slot, tmp, &dummy_slots, list) { - list_del(&slot->list); - kfree(slot); - } - if (acpi_slot_detected && dup_slot_id) - return PCIEHP_DETECT_ACPI; - return PCIEHP_DETECT_PCIE; -} - -void __init pciehp_acpi_slot_detection_init(void) -{ - slot_detection_mode = parse_detect_mode(); - if (slot_detection_mode != PCIEHP_DETECT_AUTO) - goto out; - slot_detection_mode = select_detection_mode(); -out: - if (slot_detection_mode == PCIEHP_DETECT_ACPI) - info("Using ACPI for slot detection.\n"); -} diff --git a/drivers/pci/hotplug/pciehp_core.c b/drivers/pci/hotplug/pciehp_core.c index 07aa722bb12c..5e052981f1c1 100644 --- a/drivers/pci/hotplug/pciehp_core.c +++ b/drivers/pci/hotplug/pciehp_core.c @@ -248,12 +248,9 @@ static int pciehp_probe(struct pcie_device *dev) struct slot *slot; u8 occupied, poweron; - if (pciehp_force) - dev_info(&dev->device, - "Bypassing BIOS check for pciehp use on %s\n", - pci_name(dev->port)); - else if (pciehp_acpi_slot_detection_check(dev->port)) - goto err_out_none; + /* If this is not a "hotplug" service, we have no business here. */ + if (dev->service != PCIE_PORT_SERVICE_HP) + return -ENODEV; if (!dev->port->subordinate) { /* Can happen if we run out of bus numbers during probe */ @@ -366,7 +363,6 @@ static int __init pcied_init(void) { int retval = 0; - pciehp_firmware_init(); retval = pcie_port_service_register(&hpdriver_portdrv); dbg("pcie_port_service_register = %d\n", retval); info(DRIVER_DESC " version: " DRIVER_VERSION "\n"); -- cgit v1.2.3 From 247de694349c2eeea11b8d8936541f5012a09318 Mon Sep 17 00:00:00 2001 From: Sakari Ailus Date: Fri, 22 May 2015 00:03:38 +0300 Subject: PCI: Add function 1 DMA alias quirk for Marvell 9120 Marvell 9120 SATA controller has the same issue as a number of others, so use the same quirk for this one. The other quirks were added by cc346a4714a5 ("PCI: Add function 1 DMA alias quirk for Marvell devices"). Signed-off-by: Sakari Ailus Signed-off-by: Bjorn Helgaas Acked-by: Alex Williamson --- drivers/pci/quirks.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index f126bd69396b..88d667995133 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -3572,6 +3572,8 @@ static void quirk_dma_func1_alias(struct pci_dev *dev) * SKUs this function is not present, making this a ghost requester. * https://bugzilla.kernel.org/show_bug.cgi?id=42679 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9120, + quirk_dma_func1_alias); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9123, quirk_dma_func1_alias); /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c14 */ -- cgit v1.2.3 From d0751b98dfa391f862e02dc36a233a54615e3f1d Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Thu, 21 May 2015 15:05:02 +0800 Subject: PCI: Add dev->has_secondary_link to track downstream PCIe links A PCIe Port is an interface to a Link. A Root Port is a PCI-PCI bridge in a Root Complex and has a Link on its secondary (downstream) side. For other Ports, the Link may be on either the upstream (closer to the Root Complex) or downstream side of the Port. The usual topology has a Root Port connected to an Upstream Port. We previously assumed this was the only possible topology, and that a Downstream Port's Link was always on its downstream side, like this: +---------------------+ +------+ | Downstream | | Root | | Upstream Port +--Link-- | Port +--Link--+ Port | +------+ | Downstream | | Port +--Link-- +---------------------+ But systems do exist (see URL below) where the Root Port is connected to a Downstream Port. In this case, a Downstream Port's Link may be on either the upstream or downstream side: +---------------------+ +------+ | Upstream | | Root | | Downstream Port +--Link-- | Port +--Link--+ Port | +------+ | Downstream | | Port +--Link-- +---------------------+ We can't use the Port type to determine which side the Link is on, so add a bit in struct pci_dev to keep track. A Root Port's Link is always on the Port's secondary side. A component (Endpoint or Port) on the other end of the Link obviously has the Link on its upstream side. If that component is a Port, it is part of a Switch or a Bridge. A Bridge has a PCI or PCI-X bus on its secondary side, not a Link. The internal bus of a Switch connects the Port to another Port whose Link is on the downstream side. [bhelgaas: changelog, comment, cache "type", use if/else] Link: http://lkml.kernel.org/r/54EB81B2.4050904@pobox.com Link: https://bugzilla.kernel.org/show_bug.cgi?id=94361 Suggested-by: Bjorn Helgaas Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas --- drivers/pci/probe.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) (limited to 'drivers') diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 6675a7a1b9fc..96dcd7b8303b 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -973,6 +973,8 @@ void set_pcie_port_type(struct pci_dev *pdev) { int pos; u16 reg16; + int type; + struct pci_dev *parent; pos = pci_find_capability(pdev, PCI_CAP_ID_EXP); if (!pos) @@ -982,6 +984,22 @@ void set_pcie_port_type(struct pci_dev *pdev) pdev->pcie_flags_reg = reg16; pci_read_config_word(pdev, pos + PCI_EXP_DEVCAP, ®16); pdev->pcie_mpss = reg16 & PCI_EXP_DEVCAP_PAYLOAD; + + /* + * A Root Port is always the upstream end of a Link. No PCIe + * component has two Links. Two Links are connected by a Switch + * that has a Port on each Link and internal logic to connect the + * two Ports. + */ + type = pci_pcie_type(pdev); + if (type == PCI_EXP_TYPE_ROOT_PORT) + pdev->has_secondary_link = 1; + else if (type == PCI_EXP_TYPE_UPSTREAM || + type == PCI_EXP_TYPE_DOWNSTREAM) { + parent = pci_upstream_bridge(pdev); + if (!parent->has_secondary_link) + pdev->has_secondary_link = 1; + } } void set_pcie_hotplug_bridge(struct pci_dev *pdev) -- cgit v1.2.3 From 2af31f415fa177dd11bc76f2a292b09330803c89 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Sat, 23 May 2015 00:38:57 +0200 Subject: PCI: pciehp: Drop pointless label from pciehp_probe() The err_out_none label in pciehp_probe() only leads to a return statement, so use return statements instead of jumps to it and drop it. Signed-off-by: Rafael J. Wysocki Signed-off-by: Bjorn Helgaas --- drivers/pci/hotplug/pciehp_core.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/hotplug/pciehp_core.c b/drivers/pci/hotplug/pciehp_core.c index 5e052981f1c1..4597f6bd1958 100644 --- a/drivers/pci/hotplug/pciehp_core.c +++ b/drivers/pci/hotplug/pciehp_core.c @@ -256,13 +256,13 @@ static int pciehp_probe(struct pcie_device *dev) /* Can happen if we run out of bus numbers during probe */ dev_err(&dev->device, "Hotplug bridge without secondary bus, ignoring\n"); - goto err_out_none; + return -ENODEV; } ctrl = pcie_init(dev); if (!ctrl) { dev_err(&dev->device, "Controller initialization failed\n"); - goto err_out_none; + return -ENODEV; } set_service_data(dev, ctrl); @@ -302,7 +302,6 @@ err_out_free_ctrl_slot: cleanup_slot(ctrl); err_out_release_ctlr: pciehp_release_ctrl(ctrl); -err_out_none: return -ENODEV; } -- cgit v1.2.3 From d41be3466f4243f1b198b76fe3bcd91d88194f12 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Wed, 20 May 2015 02:14:13 +0200 Subject: ACPI / hotplug / PCI: Check ignore_hotplug for all downstream devices If the ignore_hotplug flag is set for a PCI device without an ACPI companion and a bus check notification is received for an ancestor bridge that is not the device's parent, ACPIPHP will ignore that flag. Namely, in that case acpiphp_check_bridge() is called for the target bridge and if all of the devices immediately below the bridge are still present, trim_stale_devices() will be called for each of them. That function recursively walks the hierarchy downwards and removes device objects corresponding to devices that don't appear to be present any more. Unfortunately, it only checks ignore_hotplug for devices having ACPI companions, so it will remove the others (if they don't respond) regardless of the ignore_hotplug value. Fix the problem by making trim_stale_devices() take ignore_hotplug into consideration regardless of whether or not an ACPI companion is present for the device it has been called for. [bhelgaas: This may fix bug 61891, depending on whether the bridge above a device is removed along with the device] Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891 Signed-off-by: Rafael J. Wysocki Signed-off-by: Bjorn Helgaas --- drivers/pci/hotplug/acpiphp_glue.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c index bcb90e4888dd..ff538568a617 100644 --- a/drivers/pci/hotplug/acpiphp_glue.c +++ b/drivers/pci/hotplug/acpiphp_glue.c @@ -632,15 +632,14 @@ static void trim_stale_devices(struct pci_dev *dev) { struct acpi_device *adev = ACPI_COMPANION(&dev->dev); struct pci_bus *bus = dev->subordinate; - bool alive = false; + bool alive = dev->ignore_hotplug; if (adev) { acpi_status status; unsigned long long sta; status = acpi_evaluate_integer(adev->handle, "_STA", NULL, &sta); - alive = (ACPI_SUCCESS(status) && device_status_valid(sta)) - || dev->ignore_hotplug; + alive = alive || (ACPI_SUCCESS(status) && device_status_valid(sta)); } if (!alive) alive = pci_device_is_present(dev); -- cgit v1.2.3 From 0824965140fff1bf640a987dc790d1594a8e0699 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Mon, 13 Apr 2015 16:23:36 +0200 Subject: PCI: Propagate the "ignore hotplug" setting to parent Refine the mechanism introduced by commit f244d8b623da ("ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the ignore_hotplug setting of the device to its parent bridge in case hotplug notifications related to the graphics adapter switching are given for the bridge rather than for the device itself (they need to be ignored in both cases). Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891 Link: https://bugs.freedesktop.org/show_bug.cgi?id=88927 Fixes: b440bde74f04 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device") Reported-and-tested-by: tiagdtd-lava Signed-off-by: Rafael J. Wysocki Signed-off-by: Bjorn Helgaas CC: stable@vger.kernel.org # v3.17+ --- drivers/pci/pci.c | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'drivers') diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index acc4b6ef78c4..c44393f26fd3 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -4324,6 +4324,17 @@ bool pci_device_is_present(struct pci_dev *pdev) } EXPORT_SYMBOL_GPL(pci_device_is_present); +void pci_ignore_hotplug(struct pci_dev *dev) +{ + struct pci_dev *bridge = dev->bus->self; + + dev->ignore_hotplug = 1; + /* Propagate the "ignore hotplug" setting to the parent bridge. */ + if (bridge) + bridge->ignore_hotplug = 1; +} +EXPORT_SYMBOL_GPL(pci_ignore_hotplug); + #define RESOURCE_ALIGNMENT_PARAM_SIZE COMMAND_LINE_SIZE static char resource_alignment_param[RESOURCE_ALIGNMENT_PARAM_SIZE] = {0}; static DEFINE_SPINLOCK(resource_alignment_lock); -- cgit v1.2.3 From c8fc9339409df88693742d323819ab8415cd2e9d Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Thu, 21 May 2015 15:05:03 +0800 Subject: PCI/ASPM: Use dev->has_secondary_link to find downstream links We allocate pcie_link_state for the component at the upstream end of a Link. Previously we did this by allocating pcie_link_state for Root Ports and Downstream Ports. This works fine for the typical topology: 00:1c.0 Root Port [bridge to bus 02] 02:00.0 Upstream Port [bridge to bus 03] 03:00.0 Downstream Port [bridge to bus 04] 04:00.0 Endpoint or Switch Port However, it is possible to have a Root Port connected to a Downstream Port instead of an Upstream Port, as in Robert White's ATCA system: 00:1c.0 Root Port [bridge to bus 02] 02:00.0 Downstream Port [bridge to bus 03] 03:01.0 Downstream Port [bridge to bus 04] 04:00.0 Endpoint or Switch Port In this topology, we wrongly allocated pcie_link_state for the 02:00.0 Downstream Port, which is actually the *downstream* end of a link. This led to the following NULL pointer dereference when we tried to connect this link into the tree of links starting at the 00:1c.0 Root Port: BUG: unable to handle kernel NULL pointer dereference at 0000000000000088 IP: [] pcie_aspm_init_link_state+0x744/0x850 Hardware name: Kontron B3001/B3001, BIOS 4.6.3 08/07/2012 Call Trace: [] pci_scan_slot+0xd5/0x120 [] pci_scan_child_bus+0x2d/0xd0 ... Instead of relying on the component type to identify the upstream end of a link, use the "dev->has_secondary_link" field. This means it's now possible for an Upstream Port to have a link on its secondary side, so alloc_pcie_link_state() needs to connect links originating from both Upstream and Downstream Ports into the tree. [bhelgaas: changelog, add comment] Link: https://bugzilla.kernel.org/show_bug.cgi?id=94361 Link: http://lkml.kernel.org/r/54EB81B2.4050904@pobox.com Reported-by: Robert White Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas --- drivers/pci/pcie/aspm.c | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c index 4e1af7637501..a84f87247d2f 100644 --- a/drivers/pci/pcie/aspm.c +++ b/drivers/pci/pcie/aspm.c @@ -525,7 +525,7 @@ static struct pcie_link_state *alloc_pcie_link_state(struct pci_dev *pdev) INIT_LIST_HEAD(&link->children); INIT_LIST_HEAD(&link->link); link->pdev = pdev; - if (pci_pcie_type(pdev) == PCI_EXP_TYPE_DOWNSTREAM) { + if (pci_pcie_type(pdev) != PCI_EXP_TYPE_ROOT_PORT) { struct pcie_link_state *parent; parent = pdev->bus->parent->self->link_state; if (!parent) { @@ -559,10 +559,15 @@ void pcie_aspm_init_link_state(struct pci_dev *pdev) if (!aspm_support_enabled) return; - if (!pci_is_pcie(pdev) || pdev->link_state) + if (pdev->link_state) return; - if (pci_pcie_type(pdev) != PCI_EXP_TYPE_ROOT_PORT && - pci_pcie_type(pdev) != PCI_EXP_TYPE_DOWNSTREAM) + + /* + * We allocate pcie_link_state for the component on the upstream + * end of a Link, so there's nothing to do unless this device has a + * Link on its secondary side. + */ + if (!pdev->has_secondary_link) return; /* VIA has a strange chipset, root port is under a bridge */ @@ -715,8 +720,7 @@ static void __pci_disable_link_state(struct pci_dev *pdev, int state, bool sem) if (!pci_is_pcie(pdev)) return; - if (pci_pcie_type(pdev) == PCI_EXP_TYPE_ROOT_PORT || - pci_pcie_type(pdev) == PCI_EXP_TYPE_DOWNSTREAM) + if (pdev->has_secondary_link) parent = pdev; if (!parent || !parent->link_state) return; -- cgit v1.2.3 From 2dead00b925eccdc13b7cd915fa0d088b91bcb52 Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Tue, 28 Apr 2015 15:01:35 +0800 Subject: PCI: mvebu: Remove mvebu_pcie_scan_bus() After b97ea289cf6a ("PCI: Assign resources before drivers claim devices (pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so it is equivalent to mvebu_pcie_scan_bus(). Remove mvebu_pcie_scan_bus() (the hw.scan method), so we use the generic pci_scan_root_bus() path. We also need to use pci_common_init_dev() instead of pci_common_init() so we can supply the host bridge device pointer. [bhelgaas: changelog] Tested-by: Gregory CLEMENT Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas Reviewed-by: Gregory CLEMENT CC: Thomas Petazzoni CC: Jason Cooper --- drivers/pci/host/pci-mvebu.c | 18 +----------------- 1 file changed, 1 insertion(+), 17 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-mvebu.c b/drivers/pci/host/pci-mvebu.c index 1ab863551920..70aa09556ec5 100644 --- a/drivers/pci/host/pci-mvebu.c +++ b/drivers/pci/host/pci-mvebu.c @@ -751,21 +751,6 @@ static int mvebu_pcie_setup(int nr, struct pci_sys_data *sys) return 1; } -static struct pci_bus *mvebu_pcie_scan_bus(int nr, struct pci_sys_data *sys) -{ - struct mvebu_pcie *pcie = sys_to_pcie(sys); - struct pci_bus *bus; - - bus = pci_create_root_bus(&pcie->pdev->dev, sys->busnr, - &mvebu_pcie_ops, sys, &sys->resources); - if (!bus) - return NULL; - - pci_scan_child_bus(bus); - - return bus; -} - static resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev, const struct resource *res, resource_size_t start, @@ -809,12 +794,11 @@ static void mvebu_pcie_enable(struct mvebu_pcie *pcie) hw.nr_controllers = 1; hw.private_data = (void **)&pcie; hw.setup = mvebu_pcie_setup; - hw.scan = mvebu_pcie_scan_bus; hw.map_irq = of_irq_parse_and_map_pci; hw.ops = &mvebu_pcie_ops; hw.align_resource = mvebu_pcie_align_resource; - pci_common_init(&hw); + pci_common_init_dev(&pcie->pdev->dev, &hw); } /* -- cgit v1.2.3 From 915ad861b6dae6b5afa0cd8d0593916ba1ca224f Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Tue, 28 Apr 2015 15:01:36 +0800 Subject: PCI: tegra: Remove tegra_pcie_scan_bus() After b97ea289cf6a ("PCI: Assign resources before drivers claim devices (pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so it is equivalent to tegra_pcie_scan_bus(). Remove tegra_pcie_scan_bus() (the hw.scan method), so we use the generic pci_scan_root_bus() path. [bhelgaas: changelog] Tested-by: Thierry Reding Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas Acked-by: Thierry Reding --- drivers/pci/host/pci-tegra.c | 16 ---------------- 1 file changed, 16 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-tegra.c b/drivers/pci/host/pci-tegra.c index 00e92720d7f7..10c05718dbfd 100644 --- a/drivers/pci/host/pci-tegra.c +++ b/drivers/pci/host/pci-tegra.c @@ -630,21 +630,6 @@ static int tegra_pcie_map_irq(const struct pci_dev *pdev, u8 slot, u8 pin) return irq; } -static struct pci_bus *tegra_pcie_scan_bus(int nr, struct pci_sys_data *sys) -{ - struct tegra_pcie *pcie = sys_to_pcie(sys); - struct pci_bus *bus; - - bus = pci_create_root_bus(pcie->dev, sys->busnr, &tegra_pcie_ops, sys, - &sys->resources); - if (!bus) - return NULL; - - pci_scan_child_bus(bus); - - return bus; -} - static irqreturn_t tegra_pcie_isr(int irq, void *arg) { const char *err_msg[] = { @@ -1831,7 +1816,6 @@ static int tegra_pcie_enable(struct tegra_pcie *pcie) hw.private_data = (void **)&pcie; hw.setup = tegra_pcie_setup; hw.map_irq = tegra_pcie_map_irq; - hw.scan = tegra_pcie_scan_bus; hw.ops = &tegra_pcie_ops; pci_common_init_dev(pcie->dev, &hw); -- cgit v1.2.3 From 528d4bce1078f90352df909e8bcfd457d23797b2 Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Tue, 28 Apr 2015 15:01:37 +0800 Subject: PCI: designware: Use pci_scan_root_bus() for simplicity After b97ea289cf6a ("PCI: Assign resources before drivers claim devices (pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so it is equivalent to: pci_create_root_bus() pci_scan_child_bus() Use pci_scan_root_bus() to simplify the code. [bhelgaas: changelog] Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas Reviewed-by: Lucas Stach Acked-by: Jingoo Han CC: Mohit Kumar --- drivers/pci/host/pcie-designware.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c index 2e9f84fdd9ce..8c80f3850d21 100644 --- a/drivers/pci/host/pcie-designware.c +++ b/drivers/pci/host/pcie-designware.c @@ -728,13 +728,11 @@ static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys) struct pcie_port *pp = sys_to_pcie(sys); pp->root_bus_nr = sys->busnr; - bus = pci_create_root_bus(pp->dev, sys->busnr, + bus = pci_scan_root_bus(pp->dev, sys->busnr, &dw_pcie_ops, sys, &sys->resources); if (!bus) return NULL; - pci_scan_child_bus(bus); - if (bus && pp->ops->scan_bus) pp->ops->scan_bus(pp); -- cgit v1.2.3 From 18c4342aa56d70176eea85021e6fe8f6f8f39c7b Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens Date: Sun, 24 May 2015 22:37:02 +0200 Subject: PCI: iproc: Directly add PCI resources The struct iproc_pcie.resources member was pointing to a stack variable and is invalid after the registration function returned. Remove this pointer and add a parameter to the function. Tested-by: Ray Jui Signed-off-by: Hauke Mehrtens Signed-off-by: Bjorn Helgaas Reviewed-by: Ray Jui --- drivers/pci/host/pcie-iproc-bcma.c | 4 +--- drivers/pci/host/pcie-iproc-platform.c | 4 +--- drivers/pci/host/pcie-iproc.c | 4 ++-- drivers/pci/host/pcie-iproc.h | 3 +-- 4 files changed, 5 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pcie-iproc-bcma.c b/drivers/pci/host/pcie-iproc-bcma.c index 32119af0fe6a..7a412a145b51 100644 --- a/drivers/pci/host/pcie-iproc-bcma.c +++ b/drivers/pci/host/pcie-iproc-bcma.c @@ -62,11 +62,9 @@ static int iproc_pcie_bcma_probe(struct bcma_device *bdev) res_mem.flags = IORESOURCE_MEM; pci_add_resource(&res, &res_mem); - pcie->resources = &res; - pcie->map_irq = iproc_pcie_bcma_map_irq; - ret = iproc_pcie_setup(pcie); + ret = iproc_pcie_setup(pcie, &res); if (ret) { dev_err(pcie->dev, "PCIe controller setup failed\n"); return ret; diff --git a/drivers/pci/host/pcie-iproc-platform.c b/drivers/pci/host/pcie-iproc-platform.c index c8aa06f10d73..c5fe4c160972 100644 --- a/drivers/pci/host/pcie-iproc-platform.c +++ b/drivers/pci/host/pcie-iproc-platform.c @@ -69,11 +69,9 @@ static int iproc_pcie_pltfm_probe(struct platform_device *pdev) return ret; } - pcie->resources = &res; - pcie->map_irq = of_irq_parse_and_map_pci; - ret = iproc_pcie_setup(pcie); + ret = iproc_pcie_setup(pcie, &res); if (ret) { dev_err(pcie->dev, "PCIe controller setup failed\n"); return ret; diff --git a/drivers/pci/host/pcie-iproc.c b/drivers/pci/host/pcie-iproc.c index cef31f6a1242..d77481ea553e 100644 --- a/drivers/pci/host/pcie-iproc.c +++ b/drivers/pci/host/pcie-iproc.c @@ -183,7 +183,7 @@ static void iproc_pcie_enable(struct iproc_pcie *pcie) writel(SYS_RC_INTX_MASK, pcie->base + SYS_RC_INTX_EN); } -int iproc_pcie_setup(struct iproc_pcie *pcie) +int iproc_pcie_setup(struct iproc_pcie *pcie, struct list_head *res) { int ret; struct pci_bus *bus; @@ -211,7 +211,7 @@ int iproc_pcie_setup(struct iproc_pcie *pcie) pcie->sysdata.private_data = pcie; bus = pci_create_root_bus(pcie->dev, 0, &iproc_pcie_ops, - &pcie->sysdata, pcie->resources); + &pcie->sysdata, res); if (!bus) { dev_err(pcie->dev, "unable to create PCI root bus\n"); ret = -ENOMEM; diff --git a/drivers/pci/host/pcie-iproc.h b/drivers/pci/host/pcie-iproc.h index a333d4b7723a..ba0a108309cc 100644 --- a/drivers/pci/host/pcie-iproc.h +++ b/drivers/pci/host/pcie-iproc.h @@ -29,7 +29,6 @@ struct iproc_pcie { struct device *dev; void __iomem *base; - struct list_head *resources; struct pci_sys_data sysdata; struct pci_bus *root_bus; struct phy *phy; @@ -37,7 +36,7 @@ struct iproc_pcie { int (*map_irq)(const struct pci_dev *, u8, u8); }; -int iproc_pcie_setup(struct iproc_pcie *pcie); +int iproc_pcie_setup(struct iproc_pcie *pcie, struct list_head *res); int iproc_pcie_remove(struct iproc_pcie *pcie); #endif /* _PCIE_IPROC_H */ -- cgit v1.2.3 From ef07991a95de76b07594448c3521361831ec2cfe Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens Date: Sun, 24 May 2015 22:37:03 +0200 Subject: PCI: iproc: Free resource list after registration The resource list is only used in the setup process and was never freed. pci_add_resource() allocates a memory area to store the list item. Fix the memory leak. Tested-by: Ray Jui Signed-off-by: Hauke Mehrtens Signed-off-by: Bjorn Helgaas Reviewed-by: Ray Jui --- drivers/pci/host/pcie-iproc-bcma.c | 8 ++++---- drivers/pci/host/pcie-iproc-platform.c | 8 ++++---- 2 files changed, 8 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pcie-iproc-bcma.c b/drivers/pci/host/pcie-iproc-bcma.c index 7a412a145b51..96a7d999fd5e 100644 --- a/drivers/pci/host/pcie-iproc-bcma.c +++ b/drivers/pci/host/pcie-iproc-bcma.c @@ -65,12 +65,12 @@ static int iproc_pcie_bcma_probe(struct bcma_device *bdev) pcie->map_irq = iproc_pcie_bcma_map_irq; ret = iproc_pcie_setup(pcie, &res); - if (ret) { + if (ret) dev_err(pcie->dev, "PCIe controller setup failed\n"); - return ret; - } - return 0; + pci_free_resource_list(&res); + + return ret; } static void iproc_pcie_bcma_remove(struct bcma_device *bdev) diff --git a/drivers/pci/host/pcie-iproc-platform.c b/drivers/pci/host/pcie-iproc-platform.c index c5fe4c160972..9aedc8eb2c6e 100644 --- a/drivers/pci/host/pcie-iproc-platform.c +++ b/drivers/pci/host/pcie-iproc-platform.c @@ -72,12 +72,12 @@ static int iproc_pcie_pltfm_probe(struct platform_device *pdev) pcie->map_irq = of_irq_parse_and_map_pci; ret = iproc_pcie_setup(pcie, &res); - if (ret) { + if (ret) dev_err(pcie->dev, "PCIe controller setup failed\n"); - return ret; - } - return 0; + pci_free_resource_list(&res); + + return ret; } static int iproc_pcie_pltfm_remove(struct platform_device *pdev) -- cgit v1.2.3 From 777e61ea40e4a94081b3123c76ea3fe977c368a2 Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Thu, 21 May 2015 15:05:04 +0800 Subject: PCI: Use dev->has_secondary_link to find downstream PCIe links Previously we assumed that PCIe Root Ports and Downstream Ports had Links on their secondary side. That is true in most systems, but it is possible to connect a switch with either an Upstream or a Downstream Port leading downstream. Instead of relying on the component type to identify devices that have links leading downstream, use the "dev->has_secondary_link" field. [bhelgaas: changelog] Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas --- drivers/pci/pcie/aer/aerdrv_core.c | 3 +-- drivers/pci/probe.c | 2 +- drivers/pci/vc.c | 3 +-- 3 files changed, 3 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/pcie/aer/aerdrv_core.c b/drivers/pci/pcie/aer/aerdrv_core.c index 5653ea94547f..9803e3d039fe 100644 --- a/drivers/pci/pcie/aer/aerdrv_core.c +++ b/drivers/pci/pcie/aer/aerdrv_core.c @@ -425,8 +425,7 @@ static pci_ers_result_t reset_link(struct pci_dev *dev) if (driver && driver->reset_link) { status = driver->reset_link(udev); - } else if (pci_pcie_type(udev) == PCI_EXP_TYPE_DOWNSTREAM || - pci_pcie_type(udev) == PCI_EXP_TYPE_ROOT_PORT) { + } else if (udev->has_secondary_link) { status = default_reset_link(udev); } else { dev_printk(KERN_DEBUG, &dev->dev, diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 96dcd7b8303b..d405d27a92cd 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -1629,7 +1629,7 @@ static int only_one_child(struct pci_bus *bus) return 0; if (pci_pcie_type(parent) == PCI_EXP_TYPE_ROOT_PORT) return 1; - if (pci_pcie_type(parent) == PCI_EXP_TYPE_DOWNSTREAM && + if (parent->has_secondary_link && !pci_has_flag(PCI_SCAN_ALL_PCIE_DEVS)) return 1; return 0; diff --git a/drivers/pci/vc.c b/drivers/pci/vc.c index 7e1304d2e389..dfbab61a1b47 100644 --- a/drivers/pci/vc.c +++ b/drivers/pci/vc.c @@ -108,8 +108,7 @@ static void pci_vc_enable(struct pci_dev *dev, int pos, int res) struct pci_dev *link = NULL; /* Enable VCs from the downstream device */ - if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT || - pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM) + if (!dev->has_secondary_link) return; ctrl_pos = pos + PCI_VC_RES_CTRL + (res * PCI_CAP_VC_PER_VC_SIZEOF); -- cgit v1.2.3 From 19bdb6e4ec071bc49a9871b41e6a59a1657ed365 Mon Sep 17 00:00:00 2001 From: Alex Williamson Date: Tue, 26 May 2015 15:11:44 -0600 Subject: PCI: Move pci_ari_enabled() to global header pci_ari_enabled() is useful outside of drivers/pci, particularly for deriving INTx routing via ACPI _PRT, so move it to the global header. Also convert to bool return. Signed-off-by: Alex Williamson Signed-off-by: Bjorn Helgaas Reviewed-by: Don Dutile Acked-by: Rafael J. Wysocki --- drivers/pci/pci.h | 11 ----------- 1 file changed, 11 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h index 9bd762c237ab..c1b2a433ca04 100644 --- a/drivers/pci/pci.h +++ b/drivers/pci/pci.h @@ -216,17 +216,6 @@ void __pci_bus_assign_resources(const struct pci_bus *bus, struct list_head *fail_head); bool pci_bus_clip_resource(struct pci_dev *dev, int idx); -/** - * pci_ari_enabled - query ARI forwarding status - * @bus: the PCI bus - * - * Returns 1 if ARI forwarding is enabled, or 0 if not enabled; - */ -static inline int pci_ari_enabled(struct pci_bus *bus) -{ - return bus->self && bus->self->ari_enabled; -} - void pci_reassigndev_resource_alignment(struct pci_dev *dev); void pci_disable_bridge_window(struct pci_dev *dev); -- cgit v1.2.3 From 3a9ad0b4fdcd57f775d3615004c8c64c021a9e7d Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Wed, 27 May 2015 17:23:51 -0700 Subject: PCI: Add pci_bus_addr_t David Ahern reported that d63e2e1f3df9 ("sparc/PCI: Clip bridge windows to fit in upstream windows") fails to boot on sparc/T5-8: pci 0000:06:00.0: reg 0x184: can't handle BAR above 4GB (bus address 0x110204000) The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA addresses, i.e., bus addresses returned via the DMA API (dma_map_single(), etc.), while the PCI core assumed dma_addr_t could hold *any* bus address, including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so they don't fit in a dma_addr_t. d63e2e1f3df9 added new checking that tripped over this mismatch. Add pci_bus_addr_t, which is wide enough to hold any PCI bus address, including both raw BAR values and DMA addresses. This will be 64 bits on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then dma_addr_t only needs to be wide enough to hold addresses from the DMA API. [bhelgaas: changelog, bugzilla, Kconfig to ensure pci_bus_addr_t is at least as wide as dma_addr_t, documentation] Fixes: d63e2e1f3df9 ("sparc/PCI: Clip bridge windows to fit in upstream windows") Fixes: 23b13bc76f35 ("PCI: Fail safely if we can't handle BARs larger than 4GB") Link: http://lkml.kernel.org/r/CAE9FiQU1gJY1LYrxs+ma5LCTEEe4xmtjRG0aXJ9K_Tsu+m9Wuw@mail.gmail.com Link: http://lkml.kernel.org/r/1427857069-6789-1-git-send-email-yinghai@kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=96231 Reported-by: David Ahern Tested-by: David Ahern Signed-off-by: Yinghai Lu Signed-off-by: Bjorn Helgaas Acked-by: David S. Miller CC: stable@vger.kernel.org # v3.19+ --- drivers/pci/Kconfig | 4 ++++ drivers/pci/bus.c | 10 +++++----- drivers/pci/probe.c | 12 ++++++------ 3 files changed, 15 insertions(+), 11 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig index 7a8f1c5e65af..73de4efcbe6e 100644 --- a/drivers/pci/Kconfig +++ b/drivers/pci/Kconfig @@ -1,6 +1,10 @@ # # PCI configuration # +config PCI_BUS_ADDR_T_64BIT + def_bool y if (ARCH_DMA_ADDR_T_64BIT || 64BIT) + depends on PCI + config PCI_MSI bool "Message Signaled Interrupts (MSI and MSI-X)" depends on PCI diff --git a/drivers/pci/bus.c b/drivers/pci/bus.c index 90fa3a78fb7c..6fbd3f2b5992 100644 --- a/drivers/pci/bus.c +++ b/drivers/pci/bus.c @@ -92,11 +92,11 @@ void pci_bus_remove_resources(struct pci_bus *bus) } static struct pci_bus_region pci_32_bit = {0, 0xffffffffULL}; -#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT +#ifdef CONFIG_PCI_BUS_ADDR_T_64BIT static struct pci_bus_region pci_64_bit = {0, - (dma_addr_t) 0xffffffffffffffffULL}; -static struct pci_bus_region pci_high = {(dma_addr_t) 0x100000000ULL, - (dma_addr_t) 0xffffffffffffffffULL}; + (pci_bus_addr_t) 0xffffffffffffffffULL}; +static struct pci_bus_region pci_high = {(pci_bus_addr_t) 0x100000000ULL, + (pci_bus_addr_t) 0xffffffffffffffffULL}; #endif /* @@ -200,7 +200,7 @@ int pci_bus_alloc_resource(struct pci_bus *bus, struct resource *res, resource_size_t), void *alignf_data) { -#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT +#ifdef CONFIG_PCI_BUS_ADDR_T_64BIT int rc; if (res->flags & IORESOURCE_MEM_64) { diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 6675a7a1b9fc..c91185721345 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -254,8 +254,8 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type, } if (res->flags & IORESOURCE_MEM_64) { - if ((sizeof(dma_addr_t) < 8 || sizeof(resource_size_t) < 8) && - sz64 > 0x100000000ULL) { + if ((sizeof(pci_bus_addr_t) < 8 || sizeof(resource_size_t) < 8) + && sz64 > 0x100000000ULL) { res->flags |= IORESOURCE_UNSET | IORESOURCE_DISABLED; res->start = 0; res->end = 0; @@ -264,7 +264,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type, goto out; } - if ((sizeof(dma_addr_t) < 8) && l) { + if ((sizeof(pci_bus_addr_t) < 8) && l) { /* Above 32-bit boundary; try to reallocate */ res->flags |= IORESOURCE_UNSET; res->start = 0; @@ -399,7 +399,7 @@ static void pci_read_bridge_mmio_pref(struct pci_bus *child) struct pci_dev *dev = child->self; u16 mem_base_lo, mem_limit_lo; u64 base64, limit64; - dma_addr_t base, limit; + pci_bus_addr_t base, limit; struct pci_bus_region region; struct resource *res; @@ -426,8 +426,8 @@ static void pci_read_bridge_mmio_pref(struct pci_bus *child) } } - base = (dma_addr_t) base64; - limit = (dma_addr_t) limit64; + base = (pci_bus_addr_t) base64; + limit = (pci_bus_addr_t) limit64; if (base != base64) { dev_err(&dev->dev, "can't handle bridge window above 4GB (bus address %#010llx)\n", -- cgit v1.2.3 From 917bfd93d3c9c644743940deaf8fe0cff77947eb Mon Sep 17 00:00:00 2001 From: Alex Williamson Date: Tue, 26 May 2015 15:11:51 -0600 Subject: ACPI / PCI: Account for ARI in _PRT lookups The PCIe specification, rev 3.0, section 2.2.8.1, contains the following implementation note: Virtual Wire Mapping for INTx Interrupts From ARI Devices The implied Device Number for an ARI Device is 0. When ARI-aware software (including BIOS and operating system) enables ARI Forwarding in the Downstream Port immediately above an ARI Device in order to access its Extended Functions, software must comprehend that the Downstream Port will use Device Number 0 for the virtual wire mappings of INTx interrupts coming from all Functions of the ARI Device. If non-ARI-aware software attempts to determine the virtual wire mappings for Extended Functions, it can come up with incorrect mappings by examining the traditional Device Number field and finding it to be non-0. We account for this in pci_swizzle_interrupt_pin(), but it looks like we miss it here, looking for a _PRT entry with a slot matching the ARI device slot number. This can cause errors like: pcieport 0000:80:03.0: can't derive routing for PCI INT B sfc 0000:82:01.1: PCI INT B: no GSI pci_dev.irq is then invalid, resulting in errors for drivers that attempt to enable INTx on the device. Fix by using slot 0 for ARI enabled devices. Signed-off-by: Alex Williamson Signed-off-by: Bjorn Helgaas Reviewed-by: Don Dutile Acked-by: Rafael J. Wysocki --- drivers/acpi/pci_irq.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/acpi/pci_irq.c b/drivers/acpi/pci_irq.c index b1def411c0b8..4db10b189104 100644 --- a/drivers/acpi/pci_irq.c +++ b/drivers/acpi/pci_irq.c @@ -163,7 +163,7 @@ static int acpi_pci_irq_check_entry(acpi_handle handle, struct pci_dev *dev, { int segment = pci_domain_nr(dev->bus); int bus = dev->bus->number; - int device = PCI_SLOT(dev->devfn); + int device = pci_ari_enabled(dev->bus) ? 0 : PCI_SLOT(dev->devfn); struct acpi_prt_entry *entry; if (((prt->address >> 16) & 0xffff) != device || -- cgit v1.2.3 From fd5da2081b070fea6ba355f78cf79bac6e926369 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Tue, 2 Jun 2015 16:16:44 -0500 Subject: PCI: imx6: Rename imx6_pcie_start_link() to imx6_pcie_establish_link() Rename imx6_pcie_start_link() to imx6_pcie_establish_link() to follow the convention of other DesignWare-based host drivers. No functional change. Signed-off-by: Bjorn Helgaas Acked-by: Pratyush Anand --- drivers/pci/host/pci-imx6.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c index fdb95367721e..8cc012371ca7 100644 --- a/drivers/pci/host/pci-imx6.c +++ b/drivers/pci/host/pci-imx6.c @@ -359,7 +359,7 @@ static irqreturn_t imx6_pcie_msi_handler(int irq, void *arg) return dw_handle_msi_irq(pp); } -static int imx6_pcie_start_link(struct pcie_port *pp) +static int imx6_pcie_establish_link(struct pcie_port *pp) { struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp); uint32_t tmp; @@ -432,7 +432,7 @@ static void imx6_pcie_host_init(struct pcie_port *pp) dw_pcie_setup_rc(pp); - imx6_pcie_start_link(pp); + imx6_pcie_establish_link(pp); if (IS_ENABLED(CONFIG_PCI_MSI)) dw_pcie_msi_init(pp); -- cgit v1.2.3 From dcd19de36775b689df602139f3e40bfb114d5d12 Mon Sep 17 00:00:00 2001 From: Duc Dang Date: Fri, 5 Jun 2015 15:56:34 -0500 Subject: PCI: xgene: Add APM X-Gene v1 PCIe MSI/MSIX termination driver APM X-Gene v1 SoC supports its own implementation of MSI, which is not compliant to GIC V2M specification for MSI Termination. There is a single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports. This MSI block supports 2048 MSI termination ports coalesced into 16 physical HW IRQ lines and shared across all 5 PCIe ports. As there are only 16 HW IRQs to serve 2048 MSI vectors, to support set_affinity correctly for each MSI vectors, the 16 HW IRQs are statically allocated to 8 X-Gene v1 cores (2 HW IRQs for each cores). To steer MSI interrupt to target CPU, MSI vector is moved around these HW IRQs lines. With this approach, the total MSI vectors this driver supports is reduced to 256. [bhelgaas: squash doc, driver, maintainer update] Signed-off-by: Duc Dang Signed-off-by: Tanmay Inamdar Signed-off-by: Bjorn Helgaas Reviewed-by: Marc Zyngier --- drivers/pci/host/Kconfig | 9 + drivers/pci/host/Makefile | 1 + drivers/pci/host/pci-xgene-msi.c | 596 +++++++++++++++++++++++++++++++++++++++ drivers/pci/host/pci-xgene.c | 21 ++ 4 files changed, 627 insertions(+) create mode 100644 drivers/pci/host/pci-xgene-msi.c (limited to 'drivers') diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig index 1dfb567b3522..9c48e9986bc7 100644 --- a/drivers/pci/host/Kconfig +++ b/drivers/pci/host/Kconfig @@ -89,11 +89,20 @@ config PCI_XGENE depends on ARCH_XGENE depends on OF select PCIEPORTBUS + select PCI_MSI_IRQ_DOMAIN if PCI_MSI help Say Y here if you want internal PCI support on APM X-Gene SoC. There are 5 internal PCIe ports available. Each port is GEN3 capable and have varied lanes from x1 to x8. +config PCI_XGENE_MSI + bool "X-Gene v1 PCIe MSI feature" + depends on PCI_XGENE && PCI_MSI + default y + help + Say Y here if you want PCIe MSI support for the APM X-Gene v1 SoC. + This MSI driver supports 5 PCIe ports on the APM X-Gene v1 SoC. + config PCI_LAYERSCAPE bool "Freescale Layerscape PCIe controller" depends on OF && ARM diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile index f733b4e27642..1957431d3fcc 100644 --- a/drivers/pci/host/Makefile +++ b/drivers/pci/host/Makefile @@ -11,6 +11,7 @@ obj-$(CONFIG_PCIE_SPEAR13XX) += pcie-spear13xx.o obj-$(CONFIG_PCI_KEYSTONE) += pci-keystone-dw.o pci-keystone.o obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o obj-$(CONFIG_PCI_XGENE) += pci-xgene.o +obj-$(CONFIG_PCI_XGENE_MSI) += pci-xgene-msi.o obj-$(CONFIG_PCI_LAYERSCAPE) += pci-layerscape.o obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o diff --git a/drivers/pci/host/pci-xgene-msi.c b/drivers/pci/host/pci-xgene-msi.c new file mode 100644 index 000000000000..2d31d4d6fd08 --- /dev/null +++ b/drivers/pci/host/pci-xgene-msi.c @@ -0,0 +1,596 @@ +/* + * APM X-Gene MSI Driver + * + * Copyright (c) 2014, Applied Micro Circuits Corporation + * Author: Tanmay Inamdar + * Duc Dang + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define MSI_IR0 0x000000 +#define MSI_INT0 0x800000 +#define IDX_PER_GROUP 8 +#define IRQS_PER_IDX 16 +#define NR_HW_IRQS 16 +#define NR_MSI_VEC (IDX_PER_GROUP * IRQS_PER_IDX * NR_HW_IRQS) + +struct xgene_msi_group { + struct xgene_msi *msi; + int gic_irq; + u32 msi_grp; +}; + +struct xgene_msi { + struct device_node *node; + struct msi_controller mchip; + struct irq_domain *domain; + u64 msi_addr; + void __iomem *msi_regs; + unsigned long *bitmap; + struct mutex bitmap_lock; + struct xgene_msi_group *msi_groups; + int num_cpus; +}; + +/* Global data */ +static struct xgene_msi xgene_msi_ctrl; + +static struct irq_chip xgene_msi_top_irq_chip = { + .name = "X-Gene1 MSI", + .irq_enable = pci_msi_unmask_irq, + .irq_disable = pci_msi_mask_irq, + .irq_mask = pci_msi_mask_irq, + .irq_unmask = pci_msi_unmask_irq, +}; + +static struct msi_domain_info xgene_msi_domain_info = { + .flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS | + MSI_FLAG_PCI_MSIX), + .chip = &xgene_msi_top_irq_chip, +}; + +/* + * X-Gene v1 has 16 groups of MSI termination registers MSInIRx, where + * n is group number (0..F), x is index of registers in each group (0..7) + * The register layout is as follows: + * MSI0IR0 base_addr + * MSI0IR1 base_addr + 0x10000 + * ... ... + * MSI0IR6 base_addr + 0x60000 + * MSI0IR7 base_addr + 0x70000 + * MSI1IR0 base_addr + 0x80000 + * MSI1IR1 base_addr + 0x90000 + * ... ... + * MSI1IR7 base_addr + 0xF0000 + * MSI2IR0 base_addr + 0x100000 + * ... ... + * MSIFIR0 base_addr + 0x780000 + * MSIFIR1 base_addr + 0x790000 + * ... ... + * MSIFIR7 base_addr + 0x7F0000 + * MSIINT0 base_addr + 0x800000 + * MSIINT1 base_addr + 0x810000 + * ... ... + * MSIINTF base_addr + 0x8F0000 + * + * Each index register supports 16 MSI vectors (0..15) to generate interrupt. + * There are total 16 GIC IRQs assigned for these 16 groups of MSI termination + * registers. + * + * Each MSI termination group has 1 MSIINTn register (n is 0..15) to indicate + * the MSI pending status caused by 1 of its 8 index registers. + */ + +/* MSInIRx read helper */ +static u32 xgene_msi_ir_read(struct xgene_msi *msi, + u32 msi_grp, u32 msir_idx) +{ + return readl_relaxed(msi->msi_regs + MSI_IR0 + + (msi_grp << 19) + (msir_idx << 16)); +} + +/* MSIINTn read helper */ +static u32 xgene_msi_int_read(struct xgene_msi *msi, u32 msi_grp) +{ + return readl_relaxed(msi->msi_regs + MSI_INT0 + (msi_grp << 16)); +} + +/* + * With 2048 MSI vectors supported, the MSI message can be constructed using + * following scheme: + * - Divide into 8 256-vector groups + * Group 0: 0-255 + * Group 1: 256-511 + * Group 2: 512-767 + * ... + * Group 7: 1792-2047 + * - Each 256-vector group is divided into 16 16-vector groups + * As an example: 16 16-vector groups for 256-vector group 0-255 is + * Group 0: 0-15 + * Group 1: 16-32 + * ... + * Group 15: 240-255 + * - The termination address of MSI vector in 256-vector group n and 16-vector + * group x is the address of MSIxIRn + * - The data for MSI vector in 16-vector group x is x + */ +static u32 hwirq_to_reg_set(unsigned long hwirq) +{ + return (hwirq / (NR_HW_IRQS * IRQS_PER_IDX)); +} + +static u32 hwirq_to_group(unsigned long hwirq) +{ + return (hwirq % NR_HW_IRQS); +} + +static u32 hwirq_to_msi_data(unsigned long hwirq) +{ + return ((hwirq / NR_HW_IRQS) % IRQS_PER_IDX); +} + +static void xgene_compose_msi_msg(struct irq_data *data, struct msi_msg *msg) +{ + struct xgene_msi *msi = irq_data_get_irq_chip_data(data); + u32 reg_set = hwirq_to_reg_set(data->hwirq); + u32 group = hwirq_to_group(data->hwirq); + u64 target_addr = msi->msi_addr + (((8 * group) + reg_set) << 16); + + msg->address_hi = upper_32_bits(target_addr); + msg->address_lo = lower_32_bits(target_addr); + msg->data = hwirq_to_msi_data(data->hwirq); +} + +/* + * X-Gene v1 only has 16 MSI GIC IRQs for 2048 MSI vectors. To maintain + * the expected behaviour of .set_affinity for each MSI interrupt, the 16 + * MSI GIC IRQs are statically allocated to 8 X-Gene v1 cores (2 GIC IRQs + * for each core). The MSI vector is moved fom 1 MSI GIC IRQ to another + * MSI GIC IRQ to steer its MSI interrupt to correct X-Gene v1 core. As a + * consequence, the total MSI vectors that X-Gene v1 supports will be + * reduced to 256 (2048/8) vectors. + */ +static int hwirq_to_cpu(unsigned long hwirq) +{ + return (hwirq % xgene_msi_ctrl.num_cpus); +} + +static unsigned long hwirq_to_canonical_hwirq(unsigned long hwirq) +{ + return (hwirq - hwirq_to_cpu(hwirq)); +} + +static int xgene_msi_set_affinity(struct irq_data *irqdata, + const struct cpumask *mask, bool force) +{ + int target_cpu = cpumask_first(mask); + int curr_cpu; + + curr_cpu = hwirq_to_cpu(irqdata->hwirq); + if (curr_cpu == target_cpu) + return IRQ_SET_MASK_OK_DONE; + + /* Update MSI number to target the new CPU */ + irqdata->hwirq = hwirq_to_canonical_hwirq(irqdata->hwirq) + target_cpu; + + return IRQ_SET_MASK_OK; +} + +static struct irq_chip xgene_msi_bottom_irq_chip = { + .name = "MSI", + .irq_set_affinity = xgene_msi_set_affinity, + .irq_compose_msi_msg = xgene_compose_msi_msg, +}; + +static int xgene_irq_domain_alloc(struct irq_domain *domain, unsigned int virq, + unsigned int nr_irqs, void *args) +{ + struct xgene_msi *msi = domain->host_data; + int msi_irq; + + mutex_lock(&msi->bitmap_lock); + + msi_irq = bitmap_find_next_zero_area(msi->bitmap, NR_MSI_VEC, 0, + msi->num_cpus, 0); + if (msi_irq < NR_MSI_VEC) + bitmap_set(msi->bitmap, msi_irq, msi->num_cpus); + else + msi_irq = -ENOSPC; + + mutex_unlock(&msi->bitmap_lock); + + if (msi_irq < 0) + return msi_irq; + + irq_domain_set_info(domain, virq, msi_irq, + &xgene_msi_bottom_irq_chip, domain->host_data, + handle_simple_irq, NULL, NULL); + set_irq_flags(virq, IRQF_VALID); + + return 0; +} + +static void xgene_irq_domain_free(struct irq_domain *domain, + unsigned int virq, unsigned int nr_irqs) +{ + struct irq_data *d = irq_domain_get_irq_data(domain, virq); + struct xgene_msi *msi = irq_data_get_irq_chip_data(d); + u32 hwirq; + + mutex_lock(&msi->bitmap_lock); + + hwirq = hwirq_to_canonical_hwirq(d->hwirq); + bitmap_clear(msi->bitmap, hwirq, msi->num_cpus); + + mutex_unlock(&msi->bitmap_lock); + + irq_domain_free_irqs_parent(domain, virq, nr_irqs); +} + +static const struct irq_domain_ops msi_domain_ops = { + .alloc = xgene_irq_domain_alloc, + .free = xgene_irq_domain_free, +}; + +static int xgene_allocate_domains(struct xgene_msi *msi) +{ + msi->domain = irq_domain_add_linear(NULL, NR_MSI_VEC, + &msi_domain_ops, msi); + if (!msi->domain) + return -ENOMEM; + + msi->mchip.domain = pci_msi_create_irq_domain(msi->mchip.of_node, + &xgene_msi_domain_info, + msi->domain); + + if (!msi->mchip.domain) { + irq_domain_remove(msi->domain); + return -ENOMEM; + } + + return 0; +} + +static void xgene_free_domains(struct xgene_msi *msi) +{ + if (msi->mchip.domain) + irq_domain_remove(msi->mchip.domain); + if (msi->domain) + irq_domain_remove(msi->domain); +} + +static int xgene_msi_init_allocator(struct xgene_msi *xgene_msi) +{ + int size = BITS_TO_LONGS(NR_MSI_VEC) * sizeof(long); + + xgene_msi->bitmap = kzalloc(size, GFP_KERNEL); + if (!xgene_msi->bitmap) + return -ENOMEM; + + mutex_init(&xgene_msi->bitmap_lock); + + xgene_msi->msi_groups = kcalloc(NR_HW_IRQS, + sizeof(struct xgene_msi_group), + GFP_KERNEL); + if (!xgene_msi->msi_groups) + return -ENOMEM; + + return 0; +} + +static void xgene_msi_isr(unsigned int irq, struct irq_desc *desc) +{ + struct irq_chip *chip = irq_desc_get_chip(desc); + struct xgene_msi_group *msi_groups; + struct xgene_msi *xgene_msi; + unsigned int virq; + int msir_index, msir_val, hw_irq; + u32 intr_index, grp_select, msi_grp; + + chained_irq_enter(chip, desc); + + msi_groups = irq_desc_get_handler_data(desc); + xgene_msi = msi_groups->msi; + msi_grp = msi_groups->msi_grp; + + /* + * MSIINTn (n is 0..F) indicates if there is a pending MSI interrupt + * If bit x of this register is set (x is 0..7), one or more interupts + * corresponding to MSInIRx is set. + */ + grp_select = xgene_msi_int_read(xgene_msi, msi_grp); + while (grp_select) { + msir_index = ffs(grp_select) - 1; + /* + * Calculate MSInIRx address to read to check for interrupts + * (refer to termination address and data assignment + * described in xgene_compose_msi_msg() ) + */ + msir_val = xgene_msi_ir_read(xgene_msi, msi_grp, msir_index); + while (msir_val) { + intr_index = ffs(msir_val) - 1; + /* + * Calculate MSI vector number (refer to the termination + * address and data assignment described in + * xgene_compose_msi_msg function) + */ + hw_irq = (((msir_index * IRQS_PER_IDX) + intr_index) * + NR_HW_IRQS) + msi_grp; + /* + * As we have multiple hw_irq that maps to single MSI, + * always look up the virq using the hw_irq as seen from + * CPU0 + */ + hw_irq = hwirq_to_canonical_hwirq(hw_irq); + virq = irq_find_mapping(xgene_msi->domain, hw_irq); + WARN_ON(!virq); + if (virq != 0) + generic_handle_irq(virq); + msir_val &= ~(1 << intr_index); + } + grp_select &= ~(1 << msir_index); + + if (!grp_select) { + /* + * We handled all interrupts happened in this group, + * resample this group MSI_INTx register in case + * something else has been made pending in the meantime + */ + grp_select = xgene_msi_int_read(xgene_msi, msi_grp); + } + } + + chained_irq_exit(chip, desc); +} + +static int xgene_msi_remove(struct platform_device *pdev) +{ + int virq, i; + struct xgene_msi *msi = platform_get_drvdata(pdev); + + for (i = 0; i < NR_HW_IRQS; i++) { + virq = msi->msi_groups[i].gic_irq; + if (virq != 0) { + irq_set_chained_handler(virq, NULL); + irq_set_handler_data(virq, NULL); + } + } + kfree(msi->msi_groups); + + kfree(msi->bitmap); + msi->bitmap = NULL; + + xgene_free_domains(msi); + + return 0; +} + +static int xgene_msi_hwirq_alloc(unsigned int cpu) +{ + struct xgene_msi *msi = &xgene_msi_ctrl; + struct xgene_msi_group *msi_group; + cpumask_var_t mask; + int i; + int err; + + for (i = cpu; i < NR_HW_IRQS; i += msi->num_cpus) { + msi_group = &msi->msi_groups[i]; + if (!msi_group->gic_irq) + continue; + + irq_set_chained_handler(msi_group->gic_irq, + xgene_msi_isr); + err = irq_set_handler_data(msi_group->gic_irq, msi_group); + if (err) { + pr_err("failed to register GIC IRQ handler\n"); + return -EINVAL; + } + /* + * Statically allocate MSI GIC IRQs to each CPU core. + * With 8-core X-Gene v1, 2 MSI GIC IRQs are allocated + * to each core. + */ + if (alloc_cpumask_var(&mask, GFP_KERNEL)) { + cpumask_clear(mask); + cpumask_set_cpu(cpu, mask); + err = irq_set_affinity(msi_group->gic_irq, mask); + if (err) + pr_err("failed to set affinity for GIC IRQ"); + free_cpumask_var(mask); + } else { + pr_err("failed to alloc CPU mask for affinity\n"); + err = -EINVAL; + } + + if (err) { + irq_set_chained_handler(msi_group->gic_irq, NULL); + irq_set_handler_data(msi_group->gic_irq, NULL); + return err; + } + } + + return 0; +} + +static void xgene_msi_hwirq_free(unsigned int cpu) +{ + struct xgene_msi *msi = &xgene_msi_ctrl; + struct xgene_msi_group *msi_group; + int i; + + for (i = cpu; i < NR_HW_IRQS; i += msi->num_cpus) { + msi_group = &msi->msi_groups[i]; + if (!msi_group->gic_irq) + continue; + + irq_set_chained_handler(msi_group->gic_irq, NULL); + irq_set_handler_data(msi_group->gic_irq, NULL); + } +} + +static int xgene_msi_cpu_callback(struct notifier_block *nfb, + unsigned long action, void *hcpu) +{ + unsigned cpu = (unsigned long)hcpu; + + switch (action) { + case CPU_ONLINE: + case CPU_ONLINE_FROZEN: + xgene_msi_hwirq_alloc(cpu); + break; + case CPU_DEAD: + case CPU_DEAD_FROZEN: + xgene_msi_hwirq_free(cpu); + break; + default: + break; + } + + return NOTIFY_OK; +} + +static struct notifier_block xgene_msi_cpu_notifier = { + .notifier_call = xgene_msi_cpu_callback, +}; + +static const struct of_device_id xgene_msi_match_table[] = { + {.compatible = "apm,xgene1-msi"}, + {}, +}; + +static int xgene_msi_probe(struct platform_device *pdev) +{ + struct resource *res; + int rc, irq_index; + struct xgene_msi *xgene_msi; + unsigned int cpu; + int virt_msir; + u32 msi_val, msi_idx; + + xgene_msi = &xgene_msi_ctrl; + + platform_set_drvdata(pdev, xgene_msi); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + xgene_msi->msi_regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(xgene_msi->msi_regs)) { + dev_err(&pdev->dev, "no reg space\n"); + rc = -EINVAL; + goto error; + } + xgene_msi->msi_addr = res->start; + + xgene_msi->num_cpus = num_possible_cpus(); + + rc = xgene_msi_init_allocator(xgene_msi); + if (rc) { + dev_err(&pdev->dev, "Error allocating MSI bitmap\n"); + goto error; + } + + rc = xgene_allocate_domains(xgene_msi); + if (rc) { + dev_err(&pdev->dev, "Failed to allocate MSI domain\n"); + goto error; + } + + for (irq_index = 0; irq_index < NR_HW_IRQS; irq_index++) { + virt_msir = platform_get_irq(pdev, irq_index); + if (virt_msir < 0) { + dev_err(&pdev->dev, "Cannot translate IRQ index %d\n", + irq_index); + rc = -EINVAL; + goto error; + } + xgene_msi->msi_groups[irq_index].gic_irq = virt_msir; + xgene_msi->msi_groups[irq_index].msi_grp = irq_index; + xgene_msi->msi_groups[irq_index].msi = xgene_msi; + } + + /* + * MSInIRx registers are read-to-clear; before registering + * interrupt handlers, read all of them to clear spurious + * interrupts that may occur before the driver is probed. + */ + for (irq_index = 0; irq_index < NR_HW_IRQS; irq_index++) { + for (msi_idx = 0; msi_idx < IDX_PER_GROUP; msi_idx++) + msi_val = xgene_msi_ir_read(xgene_msi, irq_index, + msi_idx); + /* Read MSIINTn to confirm */ + msi_val = xgene_msi_int_read(xgene_msi, irq_index); + if (msi_val) { + dev_err(&pdev->dev, "Failed to clear spurious IRQ\n"); + rc = -EINVAL; + goto error; + } + } + + cpu_notifier_register_begin(); + + for_each_online_cpu(cpu) + if (xgene_msi_hwirq_alloc(cpu)) { + dev_err(&pdev->dev, "failed to register MSI handlers\n"); + cpu_notifier_register_done(); + goto error; + } + + rc = __register_hotcpu_notifier(&xgene_msi_cpu_notifier); + if (rc) { + dev_err(&pdev->dev, "failed to add CPU MSI notifier\n"); + cpu_notifier_register_done(); + goto error; + } + + cpu_notifier_register_done(); + + xgene_msi->mchip.of_node = pdev->dev.of_node; + rc = of_pci_msi_chip_add(&xgene_msi->mchip); + if (rc) { + dev_err(&pdev->dev, "failed to add MSI controller chip\n"); + goto error_notifier; + } + + dev_info(&pdev->dev, "APM X-Gene PCIe MSI driver loaded\n"); + + return 0; + +error_notifier: + unregister_hotcpu_notifier(&xgene_msi_cpu_notifier); +error: + xgene_msi_remove(pdev); + return rc; +} + +static struct platform_driver xgene_msi_driver = { + .driver = { + .name = "xgene-msi", + .owner = THIS_MODULE, + .of_match_table = xgene_msi_match_table, + }, + .probe = xgene_msi_probe, + .remove = xgene_msi_remove, +}; + +static int __init xgene_pcie_msi_init(void) +{ + return platform_driver_register(&xgene_msi_driver); +} +subsys_initcall(xgene_pcie_msi_init); diff --git a/drivers/pci/host/pci-xgene.c b/drivers/pci/host/pci-xgene.c index ee082c0366ec..3e5a636c9a9a 100644 --- a/drivers/pci/host/pci-xgene.c +++ b/drivers/pci/host/pci-xgene.c @@ -468,6 +468,23 @@ static int xgene_pcie_setup(struct xgene_pcie_port *port, return 0; } +static int xgene_pcie_msi_enable(struct pci_bus *bus) +{ + struct device_node *msi_node; + + msi_node = of_parse_phandle(bus->dev.of_node, + "msi-parent", 0); + if (!msi_node) + return -ENODEV; + + bus->msi = of_pci_find_msi_chip_by_node(msi_node); + if (!bus->msi) + return -ENODEV; + + bus->msi->dev = &bus->dev; + return 0; +} + static int xgene_pcie_probe_bridge(struct platform_device *pdev) { struct device_node *dn = pdev->dev.of_node; @@ -504,6 +521,10 @@ static int xgene_pcie_probe_bridge(struct platform_device *pdev) if (!bus) return -ENOMEM; + if (IS_ENABLED(CONFIG_PCI_MSI)) + if (xgene_pcie_msi_enable(bus)) + dev_info(port->dev, "failed to enable MSI\n"); + pci_scan_child_bus(bus); pci_assign_unassigned_bus_resources(bus); pci_bus_add_devices(bus); -- cgit v1.2.3 From 01d72a95188880b22190e937ed8718ed4b45bdce Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Thu, 4 Jun 2015 16:38:17 -0500 Subject: PCI: Remove unused pci_dma_burst_advice() pci_dma_burst_advice() was added by e24c2d963a60 ("[PATCH] PCI: DMA bursting advice") but apparently never used. Remove it. Signed-off-by: Bjorn Helgaas Acked-by: Michal Simek # microblaze CC: David S. Miller --- drivers/net/ethernet/sun/cassini.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/sun/cassini.c b/drivers/net/ethernet/sun/cassini.c index 3dc1f68b322d..6ce973187225 100644 --- a/drivers/net/ethernet/sun/cassini.c +++ b/drivers/net/ethernet/sun/cassini.c @@ -3058,7 +3058,6 @@ static void cas_init_mac(struct cas *cp) /* setup core arbitration weight register */ writel(CAWR_RR_DIS, cp->regs + REG_CAWR); - /* XXX Use pci_dma_burst_advice() */ #if !defined(CONFIG_SPARC64) && !defined(CONFIG_ALPHA) /* set the infinite burst register for chips that don't have * pci issues. -- cgit v1.2.3 From a5dd4b4b0570b3bf880d563969b245dfbd170c1e Mon Sep 17 00:00:00 2001 From: Alex Williamson Date: Mon, 8 Jun 2015 17:10:50 -0600 Subject: PCI: pciehp: Wait for hotplug command completion where necessary The commit referenced below deferred waiting for command completion until the start of the next command, allowing hardware to do the latching asynchronously. Unfortunately, being ready to accept a new command is the only indication we have that the previous command is completed. In cases where we need that state change to be enabled, we must still wait for completion. For instance, pciehp_reset_slot() attempts to disable anything that might generate a surprise hotplug on slots that support presence detection. If we don't wait for those settings to latch before the secondary bus reset, we negate any value in attempting to prevent the spurious hotplug. Create a base function with optional wait and helper functions so that pcie_write_cmd() turns back into the "safe" interface which waits before and after issuing a command and add pcie_write_cmd_nowait(), which eliminates the trailing wait for asynchronous completion. The following functions are returned to their previous behavior: pciehp_power_on_slot pciehp_power_off_slot pcie_disable_notification pciehp_reset_slot The rationale is that pciehp_power_on_slot() enables the link and therefore relies on completion of power-on. pciehp_power_off_slot() and pcie_disable_notification() need a wait because data structures may be freed after these calls and continued signaling from the device would be unexpected. And, of course, pciehp_reset_slot() needs to wait for the scenario outlined above. Fixes: 3461a068661c ("PCI: pciehp: Wait for hotplug command completion lazily") Signed-off-by: Alex Williamson Signed-off-by: Bjorn Helgaas CC: stable@vger.kernel.org # v3.17+ --- drivers/pci/hotplug/pciehp_hpc.c | 52 +++++++++++++++++++++++++++++----------- 1 file changed, 38 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/hotplug/pciehp_hpc.c b/drivers/pci/hotplug/pciehp_hpc.c index 0ebf754fc177..6d6868811e56 100644 --- a/drivers/pci/hotplug/pciehp_hpc.c +++ b/drivers/pci/hotplug/pciehp_hpc.c @@ -176,20 +176,17 @@ static void pcie_wait_cmd(struct controller *ctrl) jiffies_to_msecs(jiffies - ctrl->cmd_started)); } -/** - * pcie_write_cmd - Issue controller command - * @ctrl: controller to which the command is issued - * @cmd: command value written to slot control register - * @mask: bitmask of slot control register to be modified - */ -static void pcie_write_cmd(struct controller *ctrl, u16 cmd, u16 mask) +static void pcie_do_write_cmd(struct controller *ctrl, u16 cmd, + u16 mask, bool wait) { struct pci_dev *pdev = ctrl_dev(ctrl); u16 slot_ctrl; mutex_lock(&ctrl->ctrl_lock); - /* Wait for any previous command that might still be in progress */ + /* + * Always wait for any previous command that might still be in progress + */ pcie_wait_cmd(ctrl); pcie_capability_read_word(pdev, PCI_EXP_SLTCTL, &slot_ctrl); @@ -201,9 +198,33 @@ static void pcie_write_cmd(struct controller *ctrl, u16 cmd, u16 mask) ctrl->cmd_started = jiffies; ctrl->slot_ctrl = slot_ctrl; + /* + * Optionally wait for the hardware to be ready for a new command, + * indicating completion of the above issued command. + */ + if (wait) + pcie_wait_cmd(ctrl); + mutex_unlock(&ctrl->ctrl_lock); } +/** + * pcie_write_cmd - Issue controller command + * @ctrl: controller to which the command is issued + * @cmd: command value written to slot control register + * @mask: bitmask of slot control register to be modified + */ +static void pcie_write_cmd(struct controller *ctrl, u16 cmd, u16 mask) +{ + pcie_do_write_cmd(ctrl, cmd, mask, true); +} + +/* Same as above without waiting for the hardware to latch */ +static void pcie_write_cmd_nowait(struct controller *ctrl, u16 cmd, u16 mask) +{ + pcie_do_write_cmd(ctrl, cmd, mask, false); +} + bool pciehp_check_link_active(struct controller *ctrl) { struct pci_dev *pdev = ctrl_dev(ctrl); @@ -422,7 +443,7 @@ void pciehp_set_attention_status(struct slot *slot, u8 value) default: return; } - pcie_write_cmd(ctrl, slot_cmd, PCI_EXP_SLTCTL_AIC); + pcie_write_cmd_nowait(ctrl, slot_cmd, PCI_EXP_SLTCTL_AIC); ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__, pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, slot_cmd); } @@ -434,7 +455,8 @@ void pciehp_green_led_on(struct slot *slot) if (!PWR_LED(ctrl)) return; - pcie_write_cmd(ctrl, PCI_EXP_SLTCTL_PWR_IND_ON, PCI_EXP_SLTCTL_PIC); + pcie_write_cmd_nowait(ctrl, PCI_EXP_SLTCTL_PWR_IND_ON, + PCI_EXP_SLTCTL_PIC); ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__, pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, PCI_EXP_SLTCTL_PWR_IND_ON); @@ -447,7 +469,8 @@ void pciehp_green_led_off(struct slot *slot) if (!PWR_LED(ctrl)) return; - pcie_write_cmd(ctrl, PCI_EXP_SLTCTL_PWR_IND_OFF, PCI_EXP_SLTCTL_PIC); + pcie_write_cmd_nowait(ctrl, PCI_EXP_SLTCTL_PWR_IND_OFF, + PCI_EXP_SLTCTL_PIC); ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__, pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, PCI_EXP_SLTCTL_PWR_IND_OFF); @@ -460,7 +483,8 @@ void pciehp_green_led_blink(struct slot *slot) if (!PWR_LED(ctrl)) return; - pcie_write_cmd(ctrl, PCI_EXP_SLTCTL_PWR_IND_BLINK, PCI_EXP_SLTCTL_PIC); + pcie_write_cmd_nowait(ctrl, PCI_EXP_SLTCTL_PWR_IND_BLINK, + PCI_EXP_SLTCTL_PIC); ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__, pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, PCI_EXP_SLTCTL_PWR_IND_BLINK); @@ -613,7 +637,7 @@ void pcie_enable_notification(struct controller *ctrl) PCI_EXP_SLTCTL_HPIE | PCI_EXP_SLTCTL_CCIE | PCI_EXP_SLTCTL_DLLSCE); - pcie_write_cmd(ctrl, cmd, mask); + pcie_write_cmd_nowait(ctrl, cmd, mask); ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__, pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, cmd); } @@ -664,7 +688,7 @@ int pciehp_reset_slot(struct slot *slot, int probe) pci_reset_bridge_secondary_bus(ctrl->pcie->port); pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, stat_mask); - pcie_write_cmd(ctrl, ctrl_mask, ctrl_mask); + pcie_write_cmd_nowait(ctrl, ctrl_mask, ctrl_mask); ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__, pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, ctrl_mask); if (pciehp_poll_mode) -- cgit v1.2.3 From 30fb7ba6605671e575b6a7a2e69fe153d6d20141 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Tue, 2 Jun 2015 16:21:11 -0500 Subject: PCI: dra7xx: Use dw_pcie_link_up() consistently We already use dw_pcie_link_up() once in dra7xx_pcie_establish_link(), but we duplicate its code later. Use dw_pcie_link_up() for consistency. No functional change. Signed-off-by: Bjorn Helgaas Acked-by: Kishon Vijay Abraham I Acked-by: Pratyush Anand --- drivers/pci/host/pci-dra7xx.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-dra7xx.c b/drivers/pci/host/pci-dra7xx.c index 2d57e19a2cd4..e3d15d7875c2 100644 --- a/drivers/pci/host/pci-dra7xx.c +++ b/drivers/pci/host/pci-dra7xx.c @@ -107,8 +107,7 @@ static int dra7xx_pcie_establish_link(struct pcie_port *pp) dra7xx_pcie_writel(dra7xx, PCIECTRL_DRA7XX_CONF_DEVICE_CMD, reg); while (retries--) { - reg = dra7xx_pcie_readl(dra7xx, PCIECTRL_DRA7XX_CONF_PHY_CS); - if (reg & LINK_UP) + if (dw_pcie_link_up(pp)) break; usleep_range(10, 20); } -- cgit v1.2.3 From 1200edcbdd0434646fa8c8c99ab17e714ac4fa9d Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Tue, 2 Jun 2015 16:27:56 -0500 Subject: PCI: layerscape: Use dw_pcie_link_up() consistently All the other DesignWare-based drivers use dw_pcie_link_up(), so use it in this driver, too, for consistency. No functional change. Signed-off-by: Bjorn Helgaas Acked-by: Pratyush Anand --- drivers/pci/host/pci-layerscape.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-layerscape.c b/drivers/pci/host/pci-layerscape.c index 4a6e62f67579..bb5894fb81d6 100644 --- a/drivers/pci/host/pci-layerscape.c +++ b/drivers/pci/host/pci-layerscape.c @@ -70,7 +70,7 @@ static void ls_pcie_host_init(struct pcie_port *pp) dw_pcie_setup_rc(pp); - while (!ls_pcie_link_up(pp)) { + while (!dw_pcie_link_up(pp)) { usleep_range(100, 1000); count++; if (count >= 200) { -- cgit v1.2.3 From 1d3f9bac716a09af2d5d6e8601336ec9efcdccda Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Tue, 2 Jun 2015 16:24:25 -0500 Subject: PCI: layerscape: Factor out ls_pcie_establish_link() All other DesignWare-based drivers have a *_establish_link() function. This functionality is trivial for Layerscape, but factor out a ls_pcie_establish_link() for consistency with the other drivers. No functional change. Signed-off-by: Bjorn Helgaas Acked-by: Pratyush Anand --- drivers/pci/host/pci-layerscape.c | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-layerscape.c b/drivers/pci/host/pci-layerscape.c index bb5894fb81d6..434b116f1a7e 100644 --- a/drivers/pci/host/pci-layerscape.c +++ b/drivers/pci/host/pci-layerscape.c @@ -62,23 +62,30 @@ static int ls_pcie_link_up(struct pcie_port *pp) return 1; } -static void ls_pcie_host_init(struct pcie_port *pp) +static int ls_pcie_establish_link(struct pcie_port *pp) { - struct ls_pcie *pcie = to_ls_pcie(pp); int count = 0; - u32 val; - - dw_pcie_setup_rc(pp); while (!dw_pcie_link_up(pp)) { usleep_range(100, 1000); count++; if (count >= 200) { dev_err(pp->dev, "phy link never came up\n"); - return; + return -EINVAL; } } + return 0; +} + +static void ls_pcie_host_init(struct pcie_port *pp) +{ + struct ls_pcie *pcie = to_ls_pcie(pp); + u32 val; + + dw_pcie_setup_rc(pp); + ls_pcie_establish_link(pp); + /* * LS1021A Workaround for internal TKT228622 * to fix the INTx hang issue -- cgit v1.2.3 From 6cbb247e85eb4449d31a8dcb9b3f0464772b1395 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Tue, 2 Jun 2015 16:47:17 -0500 Subject: PCI: designware: Wait for link to come up with consistent style All the DesignWare-based host drivers loop waiting for the link to come up, but they do it several ways that are needlessly different. Wait for the link to come up in a consistent style across all the DesignWare drivers. No functional change. Signed-off-by: Bjorn Helgaas Acked-by: Pratyush Anand --- drivers/pci/host/pci-dra7xx.c | 16 ++++++---------- drivers/pci/host/pci-exynos.c | 34 +++++++++++++++------------------- drivers/pci/host/pci-imx6.c | 20 +++++++++----------- drivers/pci/host/pci-keystone.c | 16 +++++++--------- drivers/pci/host/pci-layerscape.c | 14 ++++++-------- drivers/pci/host/pcie-spear13xx.c | 17 ++++++++--------- 6 files changed, 51 insertions(+), 66 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-dra7xx.c b/drivers/pci/host/pci-dra7xx.c index e3d15d7875c2..80db09e47800 100644 --- a/drivers/pci/host/pci-dra7xx.c +++ b/drivers/pci/host/pci-dra7xx.c @@ -93,9 +93,9 @@ static int dra7xx_pcie_link_up(struct pcie_port *pp) static int dra7xx_pcie_establish_link(struct pcie_port *pp) { - u32 reg; - unsigned int retries = 1000; struct dra7xx_pcie *dra7xx = to_dra7xx_pcie(pp); + u32 reg; + unsigned int retries; if (dw_pcie_link_up(pp)) { dev_err(pp->dev, "link is already up\n"); @@ -106,18 +106,14 @@ static int dra7xx_pcie_establish_link(struct pcie_port *pp) reg |= LTSSM_EN; dra7xx_pcie_writel(dra7xx, PCIECTRL_DRA7XX_CONF_DEVICE_CMD, reg); - while (retries--) { + for (retries = 0; retries < 1000; retries++) { if (dw_pcie_link_up(pp)) - break; + return 0; usleep_range(10, 20); } - if (retries == 0) { - dev_err(pp->dev, "link is not up\n"); - return -ETIMEDOUT; - } - - return 0; + dev_err(pp->dev, "link is not up\n"); + return -EINVAL; } static void dra7xx_pcie_enable_interrupts(struct pcie_port *pp) diff --git a/drivers/pci/host/pci-exynos.c b/drivers/pci/host/pci-exynos.c index c139237e0e52..f9f468d9a819 100644 --- a/drivers/pci/host/pci-exynos.c +++ b/drivers/pci/host/pci-exynos.c @@ -316,9 +316,9 @@ static void exynos_pcie_assert_reset(struct pcie_port *pp) static int exynos_pcie_establish_link(struct pcie_port *pp) { - u32 val; - int count = 0; struct exynos_pcie *exynos_pcie = to_exynos_pcie(pp); + u32 val; + unsigned int retries; if (dw_pcie_link_up(pp)) { dev_err(pp->dev, "Link already up\n"); @@ -357,27 +357,23 @@ static int exynos_pcie_establish_link(struct pcie_port *pp) PCIE_APP_LTSSM_ENABLE); /* check if the link is up or not */ - while (!dw_pcie_link_up(pp)) { - mdelay(100); - count++; - if (count == 10) { - while (exynos_phy_readl(exynos_pcie, - PCIE_PHY_PLL_LOCKED) == 0) { - val = exynos_blk_readl(exynos_pcie, - PCIE_PHY_PLL_LOCKED); - dev_info(pp->dev, "PLL Locked: 0x%x\n", val); - } - /* power off phy */ - exynos_pcie_power_off_phy(pp); - - dev_err(pp->dev, "PCIe Link Fail\n"); - return -EINVAL; + for (retries = 0; retries < 10; retries++) { + if (dw_pcie_link_up(pp)) { + dev_info(pp->dev, "Link up\n"); + return 0; } + mdelay(100); } - dev_info(pp->dev, "Link up\n"); + while (exynos_phy_readl(exynos_pcie, PCIE_PHY_PLL_LOCKED) == 0) { + val = exynos_blk_readl(exynos_pcie, PCIE_PHY_PLL_LOCKED); + dev_info(pp->dev, "PLL Locked: 0x%x\n", val); + } + /* power off phy */ + exynos_pcie_power_off_phy(pp); - return 0; + dev_err(pp->dev, "PCIe Link Fail\n"); + return -EINVAL; } static void exynos_pcie_clear_irq_pulse(struct pcie_port *pp) diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c index 8cc012371ca7..af7da8ac8082 100644 --- a/drivers/pci/host/pci-imx6.c +++ b/drivers/pci/host/pci-imx6.c @@ -335,21 +335,19 @@ static void imx6_pcie_init_phy(struct pcie_port *pp) static int imx6_pcie_wait_for_link(struct pcie_port *pp) { - int count = 200; + unsigned int retries; - while (!dw_pcie_link_up(pp)) { + for (retries = 0; retries < 200; retries++) { + if (dw_pcie_link_up(pp)) + return 0; usleep_range(100, 1000); - if (--count) - continue; - - dev_err(pp->dev, "phy link never came up\n"); - dev_dbg(pp->dev, "DEBUG_R0: 0x%08x, DEBUG_R1: 0x%08x\n", - readl(pp->dbi_base + PCIE_PHY_DEBUG_R0), - readl(pp->dbi_base + PCIE_PHY_DEBUG_R1)); - return -EINVAL; } - return 0; + dev_err(pp->dev, "phy link never came up\n"); + dev_dbg(pp->dev, "DEBUG_R0: 0x%08x, DEBUG_R1: 0x%08x\n", + readl(pp->dbi_base + PCIE_PHY_DEBUG_R0), + readl(pp->dbi_base + PCIE_PHY_DEBUG_R1)); + return -EINVAL; } static irqreturn_t imx6_pcie_msi_handler(int irq, void *arg) diff --git a/drivers/pci/host/pci-keystone.c b/drivers/pci/host/pci-keystone.c index 75333b0c4f0a..b75d684aefcd 100644 --- a/drivers/pci/host/pci-keystone.c +++ b/drivers/pci/host/pci-keystone.c @@ -88,7 +88,7 @@ DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, quirk_limit_mrrs); static int ks_pcie_establish_link(struct keystone_pcie *ks_pcie) { struct pcie_port *pp = &ks_pcie->pp; - int count = 200; + unsigned int retries; dw_pcie_setup_rc(pp); @@ -99,17 +99,15 @@ static int ks_pcie_establish_link(struct keystone_pcie *ks_pcie) ks_dw_pcie_initiate_link_train(ks_pcie); /* check if the link is up or not */ - while (!dw_pcie_link_up(pp)) { + for (retries = 0; retries < 200; retries++) { + if (dw_pcie_link_up(pp)) + return 0; usleep_range(100, 1000); - if (--count) { - ks_dw_pcie_initiate_link_train(ks_pcie); - continue; - } - dev_err(pp->dev, "phy link never came up\n"); - return -EINVAL; + ks_dw_pcie_initiate_link_train(ks_pcie); } - return 0; + dev_err(pp->dev, "phy link never came up\n"); + return -EINVAL; } static void ks_pcie_msi_irq_handler(unsigned int irq, struct irq_desc *desc) diff --git a/drivers/pci/host/pci-layerscape.c b/drivers/pci/host/pci-layerscape.c index 434b116f1a7e..b2328ea13dcf 100644 --- a/drivers/pci/host/pci-layerscape.c +++ b/drivers/pci/host/pci-layerscape.c @@ -64,18 +64,16 @@ static int ls_pcie_link_up(struct pcie_port *pp) static int ls_pcie_establish_link(struct pcie_port *pp) { - int count = 0; + unsigned int retries; - while (!dw_pcie_link_up(pp)) { + for (retries = 0; retries < 200; retries++) { + if (dw_pcie_link_up(pp)) + return 0; usleep_range(100, 1000); - count++; - if (count >= 200) { - dev_err(pp->dev, "phy link never came up\n"); - return -EINVAL; - } } - return 0; + dev_err(pp->dev, "phy link never came up\n"); + return -EINVAL; } static void ls_pcie_host_init(struct pcie_port *pp) diff --git a/drivers/pci/host/pcie-spear13xx.c b/drivers/pci/host/pcie-spear13xx.c index 020d78890719..dfec4281bd50 100644 --- a/drivers/pci/host/pcie-spear13xx.c +++ b/drivers/pci/host/pcie-spear13xx.c @@ -146,10 +146,10 @@ struct pcie_app_reg { static int spear13xx_pcie_establish_link(struct pcie_port *pp) { u32 val; - int count = 0; struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp); struct pcie_app_reg *app_reg = spear13xx_pcie->app_base; u32 exp_cap_off = EXP_CAP_ID_OFFSET; + unsigned int retries; if (dw_pcie_link_up(pp)) { dev_err(pp->dev, "link already up\n"); @@ -201,17 +201,16 @@ static int spear13xx_pcie_establish_link(struct pcie_port *pp) &app_reg->app_ctrl_0); /* check if the link is up or not */ - while (!dw_pcie_link_up(pp)) { - mdelay(100); - count++; - if (count == 10) { - dev_err(pp->dev, "link Fail\n"); - return -EINVAL; + for (retries = 0; retries < 10; retries++) { + if (dw_pcie_link_up(pp)) { + dev_info(pp->dev, "link up\n"); + return 0; } + mdelay(100); } - dev_info(pp->dev, "link up\n"); - return 0; + dev_err(pp->dev, "link Fail\n"); + return -EINVAL; } static irqreturn_t spear13xx_pcie_irq_handler(int irq, void *arg) -- cgit v1.2.3 From 0c0cbb6c5a04a169320df1812e58b10362865e95 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Wed, 10 Jun 2015 14:00:21 -0500 Subject: PCI/ASPM: Simplify Clock Power Management setting Update the Link Control Enable Clock Power Management bit the same way we update the ASPM Control bits, with a single call of pcie_capability_clear_and_set_word(). No functional change; this just makes both paths use the same style. Signed-off-by: Bjorn Helgaas --- drivers/pci/pcie/aspm.c | 13 +++++-------- 1 file changed, 5 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c index a84f87247d2f..317e3558a35e 100644 --- a/drivers/pci/pcie/aspm.c +++ b/drivers/pci/pcie/aspm.c @@ -127,15 +127,12 @@ static void pcie_set_clkpm_nocheck(struct pcie_link_state *link, int enable) { struct pci_dev *child; struct pci_bus *linkbus = link->pdev->subordinate; + u32 val = enable ? PCI_EXP_LNKCTL_CLKREQ_EN : 0; - list_for_each_entry(child, &linkbus->devices, bus_list) { - if (enable) - pcie_capability_set_word(child, PCI_EXP_LNKCTL, - PCI_EXP_LNKCTL_CLKREQ_EN); - else - pcie_capability_clear_word(child, PCI_EXP_LNKCTL, - PCI_EXP_LNKCTL_CLKREQ_EN); - } + list_for_each_entry(child, &linkbus->devices, bus_list) + pcie_capability_clear_and_set_word(child, PCI_EXP_LNKCTL, + PCI_EXP_LNKCTL_CLKREQ_EN, + val); link->clkpm_enabled = !!enable; } -- cgit v1.2.3 From a0427464cf4c4ae80aaa16dbcefc39ba9a5e258b Mon Sep 17 00:00:00 2001 From: Troy Kisky Date: Fri, 12 Jun 2015 14:30:16 -0500 Subject: PCI: imx6: Add speed change timeout message Currently, the timeout is never detected as count has a value of -1 if a timeout happens, but the code is checking for 0. Also, this patch removes the unneeded final wait if a timeout occurs. [bhelgaas: reworked starting from http://lkml.kernel.org/r/1433543864-7252-1-git-send-email-troy.kisky@boundarydevices.com] Signed-off-by: Troy Kisky Signed-off-by: Bjorn Helgaas --- drivers/pci/host/pci-imx6.c | 44 +++++++++++++++++++++++++++----------------- 1 file changed, 27 insertions(+), 17 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c index fdb95367721e..c93bcdf58a56 100644 --- a/drivers/pci/host/pci-imx6.c +++ b/drivers/pci/host/pci-imx6.c @@ -352,6 +352,23 @@ static int imx6_pcie_wait_for_link(struct pcie_port *pp) return 0; } +static int imx6_pcie_wait_for_speed_change(struct pcie_port *pp) +{ + uint32_t tmp; + unsigned int retries; + + for (retries = 0; retries < 200; retries++) { + tmp = readl(pp->dbi_base + PCIE_LINK_WIDTH_SPEED_CONTROL); + /* Test if the speed change finished. */ + if (!(tmp & PORT_LOGIC_SPEED_CHANGE)) + return 0; + usleep_range(100, 1000); + } + + dev_err(pp->dev, "Speed change timeout\n"); + return -EINVAL; +} + static irqreturn_t imx6_pcie_msi_handler(int irq, void *arg) { struct pcie_port *pp = arg; @@ -363,7 +380,7 @@ static int imx6_pcie_start_link(struct pcie_port *pp) { struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp); uint32_t tmp; - int ret, count; + int ret; /* * Force Gen1 operation when starting the link. In case the link is @@ -397,29 +414,22 @@ static int imx6_pcie_start_link(struct pcie_port *pp) tmp |= PORT_LOGIC_SPEED_CHANGE; writel(tmp, pp->dbi_base + PCIE_LINK_WIDTH_SPEED_CONTROL); - count = 200; - while (count--) { - tmp = readl(pp->dbi_base + PCIE_LINK_WIDTH_SPEED_CONTROL); - /* Test if the speed change finished. */ - if (!(tmp & PORT_LOGIC_SPEED_CHANGE)) - break; - usleep_range(100, 1000); + ret = imx6_pcie_wait_for_speed_change(pp); + if (ret) { + dev_err(pp->dev, "Failed to bring link up!\n"); + return ret; } /* Make sure link training is finished as well! */ - if (count) - ret = imx6_pcie_wait_for_link(pp); - else - ret = -EINVAL; - + ret = imx6_pcie_wait_for_link(pp); if (ret) { dev_err(pp->dev, "Failed to bring link up!\n"); - } else { - tmp = readl(pp->dbi_base + 0x80); - dev_dbg(pp->dev, "Link up, Gen=%i\n", (tmp >> 16) & 0xf); + return ret; } - return ret; + tmp = readl(pp->dbi_base + 0x80); + dev_dbg(pp->dev, "Link up, Gen=%i\n", (tmp >> 16) & 0xf); + return 0; } static void imx6_pcie_host_init(struct pcie_port *pp) -- cgit v1.2.3 From 515d425bd2049e9f0f79131db58eb762fb95f2f6 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Tue, 28 Apr 2015 17:32:33 +0800 Subject: xen/pcifront: Don't use deprecated function pci_scan_bus_parented() Use pci_scan_root_bus() instead of deprecated function pci_scan_bus_parented(). Signed-off-by: Arnd Bergmann Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas CC: Konrad Rzeszutek Wilk CC: xen-devel@lists.xenproject.org --- drivers/pci/xen-pcifront.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/xen-pcifront.c b/drivers/pci/xen-pcifront.c index 7cfd2db02deb..240f38872085 100644 --- a/drivers/pci/xen-pcifront.c +++ b/drivers/pci/xen-pcifront.c @@ -446,9 +446,15 @@ static int pcifront_scan_root(struct pcifront_device *pdev, unsigned int domain, unsigned int bus) { struct pci_bus *b; + LIST_HEAD(resources); struct pcifront_sd *sd = NULL; struct pci_bus_entry *bus_entry = NULL; int err = 0; + static struct resource busn_res = { + .start = 0, + .end = 255, + .flags = IORESOURCE_BUS, + }; #ifndef CONFIG_PCI_DOMAINS if (domain != 0) { @@ -470,17 +476,21 @@ static int pcifront_scan_root(struct pcifront_device *pdev, err = -ENOMEM; goto err_out; } + pci_add_resource(&resources, &ioport_resource); + pci_add_resource(&resources, &iomem_resource); + pci_add_resource(&resources, &busn_res); pcifront_init_sd(sd, domain, bus, pdev); pci_lock_rescan_remove(); - b = pci_scan_bus_parented(&pdev->xdev->dev, bus, - &pcifront_bus_ops, sd); + b = pci_scan_root_bus(&pdev->xdev->dev, bus, + &pcifront_bus_ops, sd, &resources); if (!b) { dev_err(&pdev->xdev->dev, "Error creating PCI Frontend Bus!\n"); err = -ENOMEM; pci_unlock_rescan_remove(); + pci_free_resource_list(&resources); goto err_out; } @@ -488,7 +498,7 @@ static int pcifront_scan_root(struct pcifront_device *pdev, list_add(&bus_entry->list, &pdev->root_buses); - /* pci_scan_bus_parented skips devices which do not have a have + /* pci_scan_root_bus skips devices which do not have a * devfn==0. The pcifront_scan_bus enumerates all devfn. */ err = pcifront_scan_bus(pdev, domain, bus, b); -- cgit v1.2.3 From c0300089fd2dbeebef5ab9b6d66b4e6cedf8500a Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Tue, 28 Apr 2015 17:32:34 +0800 Subject: PCI: Remove unused pci_scan_bus_parented() No one uses pci_scan_bus_parented() any more, remove it. Signed-off-by: Yijing Wang Signed-off-by: Bjorn Helgaas --- drivers/pci/probe.c | 19 ------------------- 1 file changed, 19 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 6675a7a1b9fc..7d6a61c0d5ad 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -2094,25 +2094,6 @@ struct pci_bus *pci_scan_root_bus(struct device *parent, int bus, } EXPORT_SYMBOL(pci_scan_root_bus); -/* Deprecated; use pci_scan_root_bus() instead */ -struct pci_bus *pci_scan_bus_parented(struct device *parent, - int bus, struct pci_ops *ops, void *sysdata) -{ - LIST_HEAD(resources); - struct pci_bus *b; - - pci_add_resource(&resources, &ioport_resource); - pci_add_resource(&resources, &iomem_resource); - pci_add_resource(&resources, &busn_resource); - b = pci_create_root_bus(parent, bus, ops, sysdata, &resources); - if (b) - pci_scan_child_bus(b); - else - pci_free_resource_list(&resources); - return b; -} -EXPORT_SYMBOL(pci_scan_bus_parented); - struct pci_bus *pci_scan_bus(int bus, struct pci_ops *ops, void *sysdata) { -- cgit v1.2.3 From 1c7fae18a1fb6b6bcd6669066ee801769de0e943 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Fri, 12 Jun 2015 15:02:49 -0500 Subject: PCI: imx6: Use "u32", not "uint32_t" Use "u32", not "uint32_t", for consistency. Use "tmp", not "temp", for consistency within the driver. Signed-off-by: Bjorn Helgaas Acked-by: Richard Zhu --- drivers/pci/host/pci-imx6.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c index c93bcdf58a56..776789f0ebe0 100644 --- a/drivers/pci/host/pci-imx6.c +++ b/drivers/pci/host/pci-imx6.c @@ -354,7 +354,7 @@ static int imx6_pcie_wait_for_link(struct pcie_port *pp) static int imx6_pcie_wait_for_speed_change(struct pcie_port *pp) { - uint32_t tmp; + u32 tmp; unsigned int retries; for (retries = 0; retries < 200; retries++) { @@ -379,7 +379,7 @@ static irqreturn_t imx6_pcie_msi_handler(int irq, void *arg) static int imx6_pcie_start_link(struct pcie_port *pp) { struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp); - uint32_t tmp; + u32 tmp; int ret; /* @@ -450,19 +450,19 @@ static void imx6_pcie_host_init(struct pcie_port *pp) static void imx6_pcie_reset_phy(struct pcie_port *pp) { - uint32_t temp; + u32 tmp; - pcie_phy_read(pp->dbi_base, PHY_RX_OVRD_IN_LO, &temp); - temp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN | - PHY_RX_OVRD_IN_LO_RX_PLL_EN); - pcie_phy_write(pp->dbi_base, PHY_RX_OVRD_IN_LO, temp); + pcie_phy_read(pp->dbi_base, PHY_RX_OVRD_IN_LO, &tmp); + tmp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN | + PHY_RX_OVRD_IN_LO_RX_PLL_EN); + pcie_phy_write(pp->dbi_base, PHY_RX_OVRD_IN_LO, tmp); usleep_range(2000, 3000); - pcie_phy_read(pp->dbi_base, PHY_RX_OVRD_IN_LO, &temp); - temp &= ~(PHY_RX_OVRD_IN_LO_RX_DATA_EN | + pcie_phy_read(pp->dbi_base, PHY_RX_OVRD_IN_LO, &tmp); + tmp &= ~(PHY_RX_OVRD_IN_LO_RX_DATA_EN | PHY_RX_OVRD_IN_LO_RX_PLL_EN); - pcie_phy_write(pp->dbi_base, PHY_RX_OVRD_IN_LO, temp); + pcie_phy_write(pp->dbi_base, PHY_RX_OVRD_IN_LO, tmp); } static int imx6_pcie_link_up(struct pcie_port *pp) -- cgit v1.2.3 From 2393f79cf92ed3bfaf1a6982a18bae4d289aeda8 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Fri, 12 Jun 2015 17:27:43 -0500 Subject: PCI: imx6: Add #define PCIE_RC_LCSR Define PCIE_RC_LCSR and use it instead of the bare offset "0x80." No functional change. Signed-off-by: Bjorn Helgaas --- drivers/pci/host/pci-imx6.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c index 776789f0ebe0..a4ee579421df 100644 --- a/drivers/pci/host/pci-imx6.c +++ b/drivers/pci/host/pci-imx6.c @@ -47,6 +47,8 @@ struct imx6_pcie { #define PCIE_RC_LCR_MAX_LINK_SPEEDS_GEN2 0x2 #define PCIE_RC_LCR_MAX_LINK_SPEEDS_MASK 0xf +#define PCIE_RC_LCSR 0x80 + /* PCIe Port Logic registers (memory-mapped) */ #define PL_OFFSET 0x700 #define PCIE_PL_PFLR (PL_OFFSET + 0x08) @@ -427,7 +429,7 @@ static int imx6_pcie_start_link(struct pcie_port *pp) return ret; } - tmp = readl(pp->dbi_base + 0x80); + tmp = readl(pp->dbi_base + PCIE_RC_LCSR); dev_dbg(pp->dev, "Link up, Gen=%i\n", (tmp >> 16) & 0xf); return 0; } -- cgit v1.2.3 From 3784e0c6b02d4fa0966abb01b74eedeb8cd64603 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Mon, 15 Jun 2015 16:28:29 -0500 Subject: PCI: pciehp: Clean up debug logging The pciehp debug logging is overly verbose and often redundant. Almost all of the information printed by dbg_ctrl() is also printed by the normal PCI core enumeration code and by pcie_init(). Remove the redundant debug info. When claiming a pciehp bridge, we print the slot characteristics, e.g., Slot #6 AttnBtn- AttnInd- PwrInd- PwrCtrl- MRL- Interlock- NoCompl+ LLActRep+ Add the Hot-Plug Capable and Hot-Plug Surprise bits to this information, and print it all in the same order as lspci does. No functional change except the message text changes. Signed-off-by: Bjorn Helgaas Reviewed-by: Rajat Jain Acked-by: Yinghai Lu --- drivers/pci/hotplug/pciehp_core.c | 39 +++------------------------- drivers/pci/hotplug/pciehp_ctrl.c | 38 +++++---------------------- drivers/pci/hotplug/pciehp_hpc.c | 54 ++++++++------------------------------- 3 files changed, 20 insertions(+), 111 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/hotplug/pciehp_core.c b/drivers/pci/hotplug/pciehp_core.c index 4597f6bd1958..612b21a14df5 100644 --- a/drivers/pci/hotplug/pciehp_core.c +++ b/drivers/pci/hotplug/pciehp_core.c @@ -77,11 +77,6 @@ static int reset_slot (struct hotplug_slot *slot, int probe); */ static void release_slot(struct hotplug_slot *hotplug_slot) { - struct slot *slot = hotplug_slot->private; - - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, hotplug_slot_name(hotplug_slot)); - kfree(hotplug_slot->ops); kfree(hotplug_slot->info); kfree(hotplug_slot); @@ -129,14 +124,10 @@ static int init_slot(struct controller *ctrl) slot->hotplug_slot = hotplug; snprintf(name, SLOT_NAME_SIZE, "%u", PSN(ctrl)); - ctrl_dbg(ctrl, "Registering domain:bus:dev=%04x:%02x:00 sun=%x\n", - pci_domain_nr(ctrl->pcie->port->subordinate), - ctrl->pcie->port->subordinate->number, PSN(ctrl)); retval = pci_hp_register(hotplug, ctrl->pcie->port->subordinate, 0, name); if (retval) - ctrl_err(ctrl, - "pci_hp_register failed with error %d\n", retval); + ctrl_err(ctrl, "pci_hp_register failed: error %d\n", retval); out: if (retval) { kfree(ops); @@ -158,9 +149,6 @@ static int set_attention_status(struct hotplug_slot *hotplug_slot, u8 status) { struct slot *slot = hotplug_slot->private; - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, slot_name(slot)); - pciehp_set_attention_status(slot, status); return 0; } @@ -170,9 +158,6 @@ static int enable_slot(struct hotplug_slot *hotplug_slot) { struct slot *slot = hotplug_slot->private; - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, slot_name(slot)); - return pciehp_sysfs_enable_slot(slot); } @@ -181,9 +166,6 @@ static int disable_slot(struct hotplug_slot *hotplug_slot) { struct slot *slot = hotplug_slot->private; - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, slot_name(slot)); - return pciehp_sysfs_disable_slot(slot); } @@ -191,9 +173,6 @@ static int get_power_status(struct hotplug_slot *hotplug_slot, u8 *value) { struct slot *slot = hotplug_slot->private; - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, slot_name(slot)); - pciehp_get_power_status(slot, value); return 0; } @@ -202,9 +181,6 @@ static int get_attention_status(struct hotplug_slot *hotplug_slot, u8 *value) { struct slot *slot = hotplug_slot->private; - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, slot_name(slot)); - pciehp_get_attention_status(slot, value); return 0; } @@ -213,9 +189,6 @@ static int get_latch_status(struct hotplug_slot *hotplug_slot, u8 *value) { struct slot *slot = hotplug_slot->private; - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, slot_name(slot)); - pciehp_get_latch_status(slot, value); return 0; } @@ -224,9 +197,6 @@ static int get_adapter_status(struct hotplug_slot *hotplug_slot, u8 *value) { struct slot *slot = hotplug_slot->private; - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, slot_name(slot)); - pciehp_get_adapter_status(slot, value); return 0; } @@ -235,9 +205,6 @@ static int reset_slot(struct hotplug_slot *hotplug_slot, int probe) { struct slot *slot = hotplug_slot->private; - ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n", - __func__, slot_name(slot)); - return pciehp_reset_slot(slot, probe); } @@ -272,14 +239,14 @@ static int pciehp_probe(struct pcie_device *dev) if (rc == -EBUSY) ctrl_warn(ctrl, "Slot already registered by another hotplug driver\n"); else - ctrl_err(ctrl, "Slot initialization failed\n"); + ctrl_err(ctrl, "Slot initialization failed (%d)\n", rc); goto err_out_release_ctlr; } /* Enable events after we have setup the data structures */ rc = pcie_init_notification(ctrl); if (rc) { - ctrl_err(ctrl, "Notification initialization failed\n"); + ctrl_err(ctrl, "Notification initialization failed (%d)\n", rc); goto err_out_free_ctrl_slot; } diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c index f052e951b23e..4bdaf62b4e29 100644 --- a/drivers/pci/hotplug/pciehp_ctrl.c +++ b/drivers/pci/hotplug/pciehp_ctrl.c @@ -59,9 +59,6 @@ u8 pciehp_handle_attention_button(struct slot *p_slot) u32 event_type; struct controller *ctrl = p_slot->ctrl; - /* Attention Button Change */ - ctrl_dbg(ctrl, "Attention button interrupt received\n"); - /* * Button pressed - See if need to TAKE ACTION!!! */ @@ -79,9 +76,6 @@ u8 pciehp_handle_switch_change(struct slot *p_slot) u32 event_type; struct controller *ctrl = p_slot->ctrl; - /* Switch Change */ - ctrl_dbg(ctrl, "Switch interrupt received\n"); - pciehp_get_latch_status(p_slot, &getstatus); if (getstatus) { /* @@ -108,9 +102,6 @@ u8 pciehp_handle_presence_change(struct slot *p_slot) u8 presence_save; struct controller *ctrl = p_slot->ctrl; - /* Presence Change */ - ctrl_dbg(ctrl, "Presence/Notify input change\n"); - /* Switch is open, assume a presence change * Save the presence state */ @@ -140,8 +131,6 @@ u8 pciehp_handle_power_fault(struct slot *p_slot) u32 event_type; struct controller *ctrl = p_slot->ctrl; - /* power fault */ - ctrl_dbg(ctrl, "Power fault interrupt received\n"); ctrl_err(ctrl, "Power fault on slot %s\n", slot_name(p_slot)); event_type = INT_POWER_FAULT; ctrl_info(ctrl, "Power fault bit %x set\n", 0); @@ -155,9 +144,6 @@ void pciehp_handle_linkstate_change(struct slot *p_slot) u32 event_type; struct controller *ctrl = p_slot->ctrl; - /* Link Status Change */ - ctrl_dbg(ctrl, "Data Link Layer State change\n"); - if (pciehp_check_link_active(ctrl)) { ctrl_info(ctrl, "slot(%s): Link Up event\n", slot_name(p_slot)); @@ -298,10 +284,6 @@ static void pciehp_power_thread(struct work_struct *work) switch (info->req) { case DISABLE_REQ: - ctrl_dbg(p_slot->ctrl, - "Disabling domain:bus:device=%04x:%02x:00\n", - pci_domain_nr(p_slot->ctrl->pcie->port->subordinate), - p_slot->ctrl->pcie->port->subordinate->number); mutex_lock(&p_slot->hotplug_lock); pciehp_disable_slot(p_slot); mutex_unlock(&p_slot->hotplug_lock); @@ -310,10 +292,6 @@ static void pciehp_power_thread(struct work_struct *work) mutex_unlock(&p_slot->lock); break; case ENABLE_REQ: - ctrl_dbg(p_slot->ctrl, - "Enabling domain:bus:device=%04x:%02x:00\n", - pci_domain_nr(p_slot->ctrl->pcie->port->subordinate), - p_slot->ctrl->pcie->port->subordinate->number); mutex_lock(&p_slot->hotplug_lock); ret = pciehp_enable_slot(p_slot); mutex_unlock(&p_slot->hotplug_lock); @@ -416,7 +394,7 @@ static void handle_button_press_event(struct slot *p_slot) ctrl_info(ctrl, "Button ignore on Slot(%s)\n", slot_name(p_slot)); break; default: - ctrl_warn(ctrl, "Not a valid state\n"); + ctrl_warn(ctrl, "ignoring invalid state %#x\n", p_slot->state); break; } } @@ -507,8 +485,8 @@ static void handle_link_event(struct slot *p_slot, u32 event) } break; default: - ctrl_err(ctrl, "Not a valid state on slot(%s)\n", - slot_name(p_slot)); + ctrl_err(ctrl, "ignoring invalid state %#x on slot(%s)\n", + p_slot->state, slot_name(p_slot)); kfree(info); break; } @@ -532,7 +510,6 @@ static void interrupt_event_handler(struct work_struct *work) pciehp_green_led_off(p_slot); break; case INT_PRESENCE_ON: - ctrl_dbg(ctrl, "Surprise Insertion\n"); handle_surprise_event(p_slot); break; case INT_PRESENCE_OFF: @@ -540,7 +517,6 @@ static void interrupt_event_handler(struct work_struct *work) * Regardless of surprise capability, we need to * definitely remove a card that has been pulled out! */ - ctrl_dbg(ctrl, "Surprise Removal\n"); handle_surprise_event(p_slot); break; case INT_LINK_UP: @@ -647,8 +623,8 @@ int pciehp_sysfs_enable_slot(struct slot *p_slot) slot_name(p_slot)); break; default: - ctrl_err(ctrl, "Not a valid state on slot %s\n", - slot_name(p_slot)); + ctrl_err(ctrl, "invalid state %#x on slot %s\n", + p_slot->state, slot_name(p_slot)); break; } mutex_unlock(&p_slot->lock); @@ -682,8 +658,8 @@ int pciehp_sysfs_disable_slot(struct slot *p_slot) slot_name(p_slot)); break; default: - ctrl_err(ctrl, "Not a valid state on slot %s\n", - slot_name(p_slot)); + ctrl_err(ctrl, "invalid state %#x on slot %s\n", + p_slot->state, slot_name(p_slot)); break; } mutex_unlock(&p_slot->lock); diff --git a/drivers/pci/hotplug/pciehp_hpc.c b/drivers/pci/hotplug/pciehp_hpc.c index 6d6868811e56..e9daaa370047 100644 --- a/drivers/pci/hotplug/pciehp_hpc.c +++ b/drivers/pci/hotplug/pciehp_hpc.c @@ -312,7 +312,8 @@ int pciehp_check_link_status(struct controller *ctrl) ctrl_dbg(ctrl, "%s: lnk_status = %x\n", __func__, lnk_status); if ((lnk_status & PCI_EXP_LNKSTA_LT) || !(lnk_status & PCI_EXP_LNKSTA_NLW)) { - ctrl_err(ctrl, "Link Training Error occurs\n"); + ctrl_err(ctrl, "link training error: status %#06x\n", + lnk_status); return -1; } @@ -556,7 +557,7 @@ static irqreturn_t pcie_isr(int irq, void *dev_id) intr_loc); } while (detected); - ctrl_dbg(ctrl, "%s: intr_loc %x\n", __func__, intr_loc); + ctrl_dbg(ctrl, "pending interrupts %#06x from Slot Status\n", intr_loc); /* Check Command Complete Interrupt Pending */ if (intr_loc & PCI_EXP_SLTSTA_CC) { @@ -748,48 +749,13 @@ static void pcie_cleanup_slot(struct controller *ctrl) static inline void dbg_ctrl(struct controller *ctrl) { - int i; - u16 reg16; struct pci_dev *pdev = ctrl->pcie->port; + u16 reg16; if (!pciehp_debug) return; - ctrl_info(ctrl, "Hotplug Controller:\n"); - ctrl_info(ctrl, " Seg/Bus/Dev/Func/IRQ : %s IRQ %d\n", - pci_name(pdev), pdev->irq); - ctrl_info(ctrl, " Vendor ID : 0x%04x\n", pdev->vendor); - ctrl_info(ctrl, " Device ID : 0x%04x\n", pdev->device); - ctrl_info(ctrl, " Subsystem ID : 0x%04x\n", - pdev->subsystem_device); - ctrl_info(ctrl, " Subsystem Vendor ID : 0x%04x\n", - pdev->subsystem_vendor); - ctrl_info(ctrl, " PCIe Cap offset : 0x%02x\n", - pci_pcie_cap(pdev)); - for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) { - if (!pci_resource_len(pdev, i)) - continue; - ctrl_info(ctrl, " PCI resource [%d] : %pR\n", - i, &pdev->resource[i]); - } ctrl_info(ctrl, "Slot Capabilities : 0x%08x\n", ctrl->slot_cap); - ctrl_info(ctrl, " Physical Slot Number : %d\n", PSN(ctrl)); - ctrl_info(ctrl, " Attention Button : %3s\n", - ATTN_BUTTN(ctrl) ? "yes" : "no"); - ctrl_info(ctrl, " Power Controller : %3s\n", - POWER_CTRL(ctrl) ? "yes" : "no"); - ctrl_info(ctrl, " MRL Sensor : %3s\n", - MRL_SENS(ctrl) ? "yes" : "no"); - ctrl_info(ctrl, " Attention Indicator : %3s\n", - ATTN_LED(ctrl) ? "yes" : "no"); - ctrl_info(ctrl, " Power Indicator : %3s\n", - PWR_LED(ctrl) ? "yes" : "no"); - ctrl_info(ctrl, " Hot-Plug Surprise : %3s\n", - HP_SUPR_RM(ctrl) ? "yes" : "no"); - ctrl_info(ctrl, " EMI Present : %3s\n", - EMI(ctrl) ? "yes" : "no"); - ctrl_info(ctrl, " Command Completed : %3s\n", - NO_CMD_CMPL(ctrl) ? "no" : "yes"); pcie_capability_read_word(pdev, PCI_EXP_SLTSTA, ®16); ctrl_info(ctrl, "Slot Status : 0x%04x\n", reg16); pcie_capability_read_word(pdev, PCI_EXP_SLTCTL, ®16); @@ -818,10 +784,8 @@ struct controller *pcie_init(struct pcie_device *dev) /* Check if Data Link Layer Link Active Reporting is implemented */ pcie_capability_read_dword(pdev, PCI_EXP_LNKCAP, &link_cap); - if (link_cap & PCI_EXP_LNKCAP_DLLLARC) { - ctrl_dbg(ctrl, "Link Active Reporting supported\n"); + if (link_cap & PCI_EXP_LNKCAP_DLLLARC) ctrl->link_active_reporting = 1; - } /* Clear all remaining event bits in Slot Status register */ pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, @@ -829,13 +793,15 @@ struct controller *pcie_init(struct pcie_device *dev) PCI_EXP_SLTSTA_MRLSC | PCI_EXP_SLTSTA_PDC | PCI_EXP_SLTSTA_CC | PCI_EXP_SLTSTA_DLLSC); - ctrl_info(ctrl, "Slot #%d AttnBtn%c AttnInd%c PwrInd%c PwrCtrl%c MRL%c Interlock%c NoCompl%c LLActRep%c\n", + ctrl_info(ctrl, "Slot #%d AttnBtn%c PwrCtrl%c MRL%c AttnInd%c PwrInd%c HotPlug%c Surprise%c Interlock%c NoCompl%c LLActRep%c\n", (slot_cap & PCI_EXP_SLTCAP_PSN) >> 19, FLAG(slot_cap, PCI_EXP_SLTCAP_ABP), - FLAG(slot_cap, PCI_EXP_SLTCAP_AIP), - FLAG(slot_cap, PCI_EXP_SLTCAP_PIP), FLAG(slot_cap, PCI_EXP_SLTCAP_PCP), FLAG(slot_cap, PCI_EXP_SLTCAP_MRLSP), + FLAG(slot_cap, PCI_EXP_SLTCAP_AIP), + FLAG(slot_cap, PCI_EXP_SLTCAP_PIP), + FLAG(slot_cap, PCI_EXP_SLTCAP_HPC), + FLAG(slot_cap, PCI_EXP_SLTCAP_HPS), FLAG(slot_cap, PCI_EXP_SLTCAP_EIP), FLAG(slot_cap, PCI_EXP_SLTCAP_NCCS), FLAG(link_cap, PCI_EXP_LNKCAP_DLLLARC)); -- cgit v1.2.3 From f09f8735fb9ca113239fead45d96a48660cc2ae3 Mon Sep 17 00:00:00 2001 From: Duc Dang Date: Fri, 12 Jun 2015 17:35:57 -0700 Subject: PCI: xgene: Disable Configuration Request Retry Status for v1 silicon When a CPU reads the Vendor and Device ID of a non-existent device, the controller should fabricate return data of 0xFFFFFFFF. Configuration Request Retry Status (CRS) is not applicable in this case because the device doesn't exist at all. The X-Gene v1 PCIe controller has a bug in the CRS logic such that when CRS is enabled, it fabricates return data of 0xFFFF0001 for this case, which means "the device exists but is not ready." That causes the PCI core to retry the read until it times out after 60 seconds. Disable CRS capability advertisement by clearing the CRS Software Visibility bit in the Root Capabilities Register. [bhelgaas: changelog and comment] Tested-by: Ian Campbell Tested-by: Marcin Juszkiewicz Signed-off-by: Duc Dang Signed-off-by: Bjorn Helgaas Acked-by: Tanmay Inamdar --- drivers/pci/host/pci-xgene.c | 41 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 40 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-xgene.c b/drivers/pci/host/pci-xgene.c index 3e5a636c9a9a..70af714a2d43 100644 --- a/drivers/pci/host/pci-xgene.c +++ b/drivers/pci/host/pci-xgene.c @@ -59,6 +59,12 @@ #define SZ_1T (SZ_1G*1024ULL) #define PIPE_PHY_RATE_RD(src) ((0xc000 & (u32)(src)) >> 0xe) +#define ROOT_CAP_AND_CTRL 0x5C + +/* PCIe IP version */ +#define XGENE_PCIE_IP_VER_UNKN 0 +#define XGENE_PCIE_IP_VER_1 1 + struct xgene_pcie_port { struct device_node *node; struct device *dev; @@ -67,6 +73,7 @@ struct xgene_pcie_port { void __iomem *cfg_base; unsigned long cfg_addr; bool link_up; + u32 version; }; static inline u32 pcie_bar_low_val(u32 addr, u32 flags) @@ -140,9 +147,37 @@ static void __iomem *xgene_pcie_map_bus(struct pci_bus *bus, unsigned int devfn, return xgene_pcie_get_cfg_base(bus) + offset; } +static int xgene_pcie_config_read32(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 *val) +{ + struct xgene_pcie_port *port = bus->sysdata; + + if (pci_generic_config_read32(bus, devfn, where & ~0x3, 4, val) != + PCIBIOS_SUCCESSFUL) + return PCIBIOS_DEVICE_NOT_FOUND; + + /* + * The v1 controller has a bug in its Configuration Request + * Retry Status (CRS) logic: when CRS is enabled and we read the + * Vendor and Device ID of a non-existent device, the controller + * fabricates return data of 0xFFFF0001 ("device exists but is not + * ready") instead of 0xFFFFFFFF ("device does not exist"). This + * causes the PCI core to retry the read until it times out. + * Avoid this by not claiming to support CRS. + */ + if (pci_is_root_bus(bus) && (port->version == XGENE_PCIE_IP_VER_1) && + ((where & ~0x3) == ROOT_CAP_AND_CTRL)) + *val &= ~(PCI_EXP_RTCAP_CRSVIS << 16); + + if (size <= 2) + *val = (*val >> (8 * (where & 3))) & ((1 << (size * 8)) - 1); + + return PCIBIOS_SUCCESSFUL; +} + static struct pci_ops xgene_pcie_ops = { .map_bus = xgene_pcie_map_bus, - .read = pci_generic_config_read32, + .read = xgene_pcie_config_read32, .write = pci_generic_config_write32, }; @@ -500,6 +535,10 @@ static int xgene_pcie_probe_bridge(struct platform_device *pdev) port->node = of_node_get(pdev->dev.of_node); port->dev = &pdev->dev; + port->version = XGENE_PCIE_IP_VER_UNKN; + if (of_device_is_compatible(port->node, "apm,xgene-pcie")) + port->version = XGENE_PCIE_IP_VER_1; + ret = xgene_pcie_map_reg(port, pdev); if (ret) return ret; -- cgit v1.2.3 From ae4fa5f4502bfa7e7f31fc99a1da41189422642d Mon Sep 17 00:00:00 2001 From: Duc Dang Date: Thu, 18 Jun 2015 11:45:39 -0700 Subject: PCI: xgene: Allow config access to Root Port even when link is down Previously, when a Root Port's link was down, we didn't allow config access to the Root Port, which meant that if the Root Port led to an empty slot, "lspci" didn't even show the Root Port. Allow config access to Root Port even when link is down. [bhelgaas: changelog, fold in unused var fix] Suggested-by: Bjorn Helgaas Signed-off-by: Duc Dang Signed-off-by: Tanmay Inamdar Signed-off-by: Bjorn Helgaas --- drivers/pci/host/pci-xgene.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/host/pci-xgene.c b/drivers/pci/host/pci-xgene.c index 70af714a2d43..a9dfb70d623a 100644 --- a/drivers/pci/host/pci-xgene.c +++ b/drivers/pci/host/pci-xgene.c @@ -137,9 +137,7 @@ static bool xgene_pcie_hide_rc_bars(struct pci_bus *bus, int offset) static void __iomem *xgene_pcie_map_bus(struct pci_bus *bus, unsigned int devfn, int offset) { - struct xgene_pcie_port *port = bus->sysdata; - - if ((pci_is_root_bus(bus) && devfn != 0) || !port->link_up || + if ((pci_is_root_bus(bus) && devfn != 0) || xgene_pcie_hide_rc_bars(bus, offset)) return NULL; -- cgit v1.2.3 From 7d852b68badd257b2cf98c2759b9d93dac7b86a8 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Sun, 14 Jun 2015 21:27:52 -0500 Subject: PCI: pciehp: Make queue_interrupt_event() void Nobody looks at the return value from queue_interrupt_event(), so errors were silently ignored. Convert it to a "void" function and note the error in the dmesg log. No functional change except the new message. Signed-off-by: Bjorn Helgaas Reviewed-by: Rajat Jain Acked-by: Yinghai Lu --- drivers/pci/hotplug/pciehp_ctrl.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c index 4bdaf62b4e29..1086041dca1e 100644 --- a/drivers/pci/hotplug/pciehp_ctrl.c +++ b/drivers/pci/hotplug/pciehp_ctrl.c @@ -37,21 +37,20 @@ static void interrupt_event_handler(struct work_struct *work); -static int queue_interrupt_event(struct slot *p_slot, u32 event_type) +static void queue_interrupt_event(struct slot *p_slot, u32 event_type) { struct event_info *info; info = kmalloc(sizeof(*info), GFP_ATOMIC); - if (!info) - return -ENOMEM; + if (!info) { + ctrl_err(p_slot->ctrl, "dropped event %d (ENOMEM)\n", event_type); + return; + } + INIT_WORK(&info->work, interrupt_event_handler); info->event_type = event_type; info->p_slot = p_slot; - INIT_WORK(&info->work, interrupt_event_handler); - queue_work(p_slot->wq, &info->work); - - return 0; } u8 pciehp_handle_attention_button(struct slot *p_slot) -- cgit v1.2.3 From d49eccb3c1a41b847380279d7f88a88421783f37 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Sun, 14 Jun 2015 21:25:02 -0500 Subject: PCI: pciehp: Rename queue_interrupt_event() to pciehp_queue_interrupt_event() Rename queue_interrupt_event() to pciehp_queue_interrupt_event() so we can make it extern and call it from pcie_isr(). No functional change. Signed-off-by: Bjorn Helgaas Reviewed-by: Rajat Jain Acked-by: Yinghai Lu --- drivers/pci/hotplug/pciehp_ctrl.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c index 1086041dca1e..7ed37dc4879a 100644 --- a/drivers/pci/hotplug/pciehp_ctrl.c +++ b/drivers/pci/hotplug/pciehp_ctrl.c @@ -37,7 +37,7 @@ static void interrupt_event_handler(struct work_struct *work); -static void queue_interrupt_event(struct slot *p_slot, u32 event_type) +static void pciehp_queue_interrupt_event(struct slot *p_slot, u32 event_type) { struct event_info *info; @@ -64,7 +64,7 @@ u8 pciehp_handle_attention_button(struct slot *p_slot) ctrl_info(ctrl, "Button pressed on Slot(%s)\n", slot_name(p_slot)); event_type = INT_BUTTON_PRESS; - queue_interrupt_event(p_slot, event_type); + pciehp_queue_interrupt_event(p_slot, event_type); return 0; } @@ -90,7 +90,7 @@ u8 pciehp_handle_switch_change(struct slot *p_slot) event_type = INT_SWITCH_CLOSE; } - queue_interrupt_event(p_slot, event_type); + pciehp_queue_interrupt_event(p_slot, event_type); return 1; } @@ -120,7 +120,7 @@ u8 pciehp_handle_presence_change(struct slot *p_slot) event_type = INT_PRESENCE_OFF; } - queue_interrupt_event(p_slot, event_type); + pciehp_queue_interrupt_event(p_slot, event_type); return 1; } @@ -133,7 +133,7 @@ u8 pciehp_handle_power_fault(struct slot *p_slot) ctrl_err(ctrl, "Power fault on slot %s\n", slot_name(p_slot)); event_type = INT_POWER_FAULT; ctrl_info(ctrl, "Power fault bit %x set\n", 0); - queue_interrupt_event(p_slot, event_type); + pciehp_queue_interrupt_event(p_slot, event_type); return 1; } @@ -153,7 +153,7 @@ void pciehp_handle_linkstate_change(struct slot *p_slot) event_type = INT_LINK_DOWN; } - queue_interrupt_event(p_slot, event_type); + pciehp_queue_interrupt_event(p_slot, event_type); } /* The following routines constitute the bulk of the -- cgit v1.2.3 From 4f092fec67191f899fa111a4eeffdf4368494c77 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Sun, 14 Jun 2015 21:35:13 -0500 Subject: PCI: pciehp: Inline the "handle event" functions into the ISR The pciehp_handle_*() functions (pciehp_handle_attention_button(), etc.) only contain a line or two of useful code, so it's clumsy to put them in separate functions. All they so is add an event to a work queue, and it's clearer to see that directly in the ISR. Inline them directly into pcie_isr(). No functional change. Signed-off-by: Bjorn Helgaas Reviewed-by: Rajat Jain Acked-by: Yinghai Lu --- drivers/pci/hotplug/pciehp.h | 6 +-- drivers/pci/hotplug/pciehp_ctrl.c | 105 +------------------------------------- drivers/pci/hotplug/pciehp_hpc.c | 39 ++++++++++---- 3 files changed, 32 insertions(+), 118 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/hotplug/pciehp.h b/drivers/pci/hotplug/pciehp.h index ce4d12c4eff4..57cd1327346f 100644 --- a/drivers/pci/hotplug/pciehp.h +++ b/drivers/pci/hotplug/pciehp.h @@ -132,11 +132,7 @@ struct controller { int pciehp_sysfs_enable_slot(struct slot *slot); int pciehp_sysfs_disable_slot(struct slot *slot); -u8 pciehp_handle_attention_button(struct slot *p_slot); -u8 pciehp_handle_switch_change(struct slot *p_slot); -u8 pciehp_handle_presence_change(struct slot *p_slot); -u8 pciehp_handle_power_fault(struct slot *p_slot); -void pciehp_handle_linkstate_change(struct slot *p_slot); +void pciehp_queue_interrupt_event(struct slot *slot, u32 event_type); int pciehp_configure_device(struct slot *p_slot); int pciehp_unconfigure_device(struct slot *p_slot); void pciehp_queue_pushbutton_work(struct work_struct *work); diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c index 7ed37dc4879a..f3796124ad7c 100644 --- a/drivers/pci/hotplug/pciehp_ctrl.c +++ b/drivers/pci/hotplug/pciehp_ctrl.c @@ -37,7 +37,7 @@ static void interrupt_event_handler(struct work_struct *work); -static void pciehp_queue_interrupt_event(struct slot *p_slot, u32 event_type) +void pciehp_queue_interrupt_event(struct slot *p_slot, u32 event_type) { struct event_info *info; @@ -53,109 +53,6 @@ static void pciehp_queue_interrupt_event(struct slot *p_slot, u32 event_type) queue_work(p_slot->wq, &info->work); } -u8 pciehp_handle_attention_button(struct slot *p_slot) -{ - u32 event_type; - struct controller *ctrl = p_slot->ctrl; - - /* - * Button pressed - See if need to TAKE ACTION!!! - */ - ctrl_info(ctrl, "Button pressed on Slot(%s)\n", slot_name(p_slot)); - event_type = INT_BUTTON_PRESS; - - pciehp_queue_interrupt_event(p_slot, event_type); - - return 0; -} - -u8 pciehp_handle_switch_change(struct slot *p_slot) -{ - u8 getstatus; - u32 event_type; - struct controller *ctrl = p_slot->ctrl; - - pciehp_get_latch_status(p_slot, &getstatus); - if (getstatus) { - /* - * Switch opened - */ - ctrl_info(ctrl, "Latch open on Slot(%s)\n", slot_name(p_slot)); - event_type = INT_SWITCH_OPEN; - } else { - /* - * Switch closed - */ - ctrl_info(ctrl, "Latch close on Slot(%s)\n", slot_name(p_slot)); - event_type = INT_SWITCH_CLOSE; - } - - pciehp_queue_interrupt_event(p_slot, event_type); - - return 1; -} - -u8 pciehp_handle_presence_change(struct slot *p_slot) -{ - u32 event_type; - u8 presence_save; - struct controller *ctrl = p_slot->ctrl; - - /* Switch is open, assume a presence change - * Save the presence state - */ - pciehp_get_adapter_status(p_slot, &presence_save); - if (presence_save) { - /* - * Card Present - */ - ctrl_info(ctrl, "Card present on Slot(%s)\n", slot_name(p_slot)); - event_type = INT_PRESENCE_ON; - } else { - /* - * Not Present - */ - ctrl_info(ctrl, "Card not present on Slot(%s)\n", - slot_name(p_slot)); - event_type = INT_PRESENCE_OFF; - } - - pciehp_queue_interrupt_event(p_slot, event_type); - - return 1; -} - -u8 pciehp_handle_power_fault(struct slot *p_slot) -{ - u32 event_type; - struct controller *ctrl = p_slot->ctrl; - - ctrl_err(ctrl, "Power fault on slot %s\n", slot_name(p_slot)); - event_type = INT_POWER_FAULT; - ctrl_info(ctrl, "Power fault bit %x set\n", 0); - pciehp_queue_interrupt_event(p_slot, event_type); - - return 1; -} - -void pciehp_handle_linkstate_change(struct slot *p_slot) -{ - u32 event_type; - struct controller *ctrl = p_slot->ctrl; - - if (pciehp_check_link_active(ctrl)) { - ctrl_info(ctrl, "slot(%s): Link Up event\n", - slot_name(p_slot)); - event_type = INT_LINK_UP; - } else { - ctrl_info(ctrl, "slot(%s): Link Down event\n", - slot_name(p_slot)); - event_type = INT_LINK_DOWN; - } - - pciehp_queue_interrupt_event(p_slot, event_type); -} - /* The following routines constitute the bulk of the hotplug controller logic */ diff --git a/drivers/pci/hotplug/pciehp_hpc.c b/drivers/pci/hotplug/pciehp_hpc.c index e9daaa370047..2913f7e68a10 100644 --- a/drivers/pci/hotplug/pciehp_hpc.c +++ b/drivers/pci/hotplug/pciehp_hpc.c @@ -535,6 +535,8 @@ static irqreturn_t pcie_isr(int irq, void *dev_id) struct pci_dev *dev; struct slot *slot = ctrl->slot; u16 detected, intr_loc; + u8 open, present; + bool link; /* * In order to guarantee that all interrupt events are @@ -580,25 +582,44 @@ static irqreturn_t pcie_isr(int irq, void *dev_id) return IRQ_HANDLED; /* Check MRL Sensor Changed */ - if (intr_loc & PCI_EXP_SLTSTA_MRLSC) - pciehp_handle_switch_change(slot); + if (intr_loc & PCI_EXP_SLTSTA_MRLSC) { + pciehp_get_latch_status(slot, &open); + ctrl_info(ctrl, "Latch %s on Slot(%s)\n", + open ? "open" : "close", slot_name(slot)); + pciehp_queue_interrupt_event(slot, open ? INT_SWITCH_OPEN : + INT_SWITCH_CLOSE); + } /* Check Attention Button Pressed */ - if (intr_loc & PCI_EXP_SLTSTA_ABP) - pciehp_handle_attention_button(slot); + if (intr_loc & PCI_EXP_SLTSTA_ABP) { + ctrl_info(ctrl, "Button pressed on Slot(%s)\n", + slot_name(slot)); + pciehp_queue_interrupt_event(slot, INT_BUTTON_PRESS); + } /* Check Presence Detect Changed */ - if (intr_loc & PCI_EXP_SLTSTA_PDC) - pciehp_handle_presence_change(slot); + if (intr_loc & PCI_EXP_SLTSTA_PDC) { + pciehp_get_adapter_status(slot, &present); + ctrl_info(ctrl, "Card %spresent on Slot(%s)\n", + present ? "" : "not ", slot_name(slot)); + pciehp_queue_interrupt_event(slot, present ? INT_PRESENCE_ON : + INT_PRESENCE_OFF); + } /* Check Power Fault Detected */ if ((intr_loc & PCI_EXP_SLTSTA_PFD) && !ctrl->power_fault_detected) { ctrl->power_fault_detected = 1; - pciehp_handle_power_fault(slot); + ctrl_err(ctrl, "Power fault on slot %s\n", slot_name(slot)); + pciehp_queue_interrupt_event(slot, INT_POWER_FAULT); } - if (intr_loc & PCI_EXP_SLTSTA_DLLSC) - pciehp_handle_linkstate_change(slot); + if (intr_loc & PCI_EXP_SLTSTA_DLLSC) { + link = pciehp_check_link_active(ctrl); + ctrl_info(ctrl, "slot(%s): Link %s event\n", + slot_name(slot), link ? "Up" : "Down"); + pciehp_queue_interrupt_event(slot, link ? INT_LINK_UP : + INT_LINK_DOWN); + } return IRQ_HANDLED; } -- cgit v1.2.3