From 5a9a8e32ebe269c71d8d3e78f9435fe7729f38e9 Mon Sep 17 00:00:00 2001 From: Ed Swierk Date: Tue, 2 Jun 2009 00:19:52 -0700 Subject: forcedeth: add phy_power_down parameter, leave phy powered up by default (v2) Add a phy_power_down parameter to forcedeth: set to 1 to power down the phy and disable the link when an interface goes down; set to 0 to always leave the phy powered up. The phy power state persists across reboots; Windows, some BIOSes, and older versions of Linux don't bother to power up the phy again, forcing users to remove all power to get the interface working (see http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy powered on is the safest default behavior. Users accustomed to seeing the link state reflect the interface state and/or wanting to minimize power consumption can set phy_power_down=1 if compatibility with other OSes is not an issue. Signed-off-by: Ed Swierk Signed-off-by: David S. Miller --- drivers/net/forcedeth.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index f9a846b1b92f..9f6a68fb7b45 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -897,6 +897,12 @@ enum { }; static int phy_cross = NV_CROSSOVER_DETECTION_DISABLED; +/* + * Power down phy when interface is down (persists through reboot; + * older Linux and other OSes may not power it up again) + */ +static int phy_power_down = 0; + static inline struct fe_priv *get_nvpriv(struct net_device *dev) { return netdev_priv(dev); @@ -1485,7 +1491,10 @@ static int phy_init(struct net_device *dev) /* restart auto negotiation, power down phy */ mii_control = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ); - mii_control |= (BMCR_ANRESTART | BMCR_ANENABLE | BMCR_PDOWN); + mii_control |= (BMCR_ANRESTART | BMCR_ANENABLE); + if (phy_power_down) { + mii_control |= BMCR_PDOWN; + } if (mii_rw(dev, np->phyaddr, MII_BMCR, mii_control)) { return PHY_ERROR; } @@ -5513,7 +5522,7 @@ static int nv_close(struct net_device *dev) nv_drain_rxtx(dev); - if (np->wolenabled) { + if (np->wolenabled || !phy_power_down) { writel(NVREG_PFF_ALWAYS|NVREG_PFF_MYADDR, base + NvRegPacketFilterFlags); nv_start_rx(dev); } else { @@ -6367,6 +6376,8 @@ module_param(dma_64bit, int, 0); MODULE_PARM_DESC(dma_64bit, "High DMA is enabled by setting to 1 and disabled by setting to 0."); module_param(phy_cross, int, 0); MODULE_PARM_DESC(phy_cross, "Phy crossover detection for Realtek 8201 phy is enabled by setting to 1 and disabled by setting to 0."); +module_param(phy_power_down, int, 0); +MODULE_PARM_DESC(phy_power_down, "Power down phy and disable link when interface is down (1), or leave phy powered up (0)."); MODULE_AUTHOR("Manfred Spraul "); MODULE_DESCRIPTION("Reverse Engineered nForce ethernet driver"); -- cgit v1.2.3 From ea30e11970a96cfe5e32c03a29332554573b4a10 Mon Sep 17 00:00:00 2001 From: Neil Horman Date: Tue, 2 Jun 2009 01:29:58 -0700 Subject: e1000: add missing length check to e1000 receive routine Patch to fix bad length checking in e1000. E1000 by default does two things: 1) Spans rx descriptors for packets that don't fit into 1 skb on recieve 2) Strips the crc from a frame by subtracting 4 bytes from the length prior to doing an skb_put Since the e1000 driver isn't written to support receiving packets that span multiple rx buffers, it checks the End of Packet bit of every frame, and discards it if its not set. This places us in a situation where, if we have a spanning packet, the first part is discarded, but the second part is not (since it is the end of packet, and it passes the EOP bit test). If the second part of the frame is small (4 bytes or less), we subtract 4 from it to remove its crc, underflow the length, and wind up in skb_over_panic, when we try to skb_put a huge number of bytes into the skb. This amounts to a remote DOS attack through careful selection of frame size in relation to interface MTU. The fix for this is already in the e1000e driver, as well as the e1000 sourceforge driver, but no one ever pushed it to e1000. This is lifted straight from e1000e, and prevents small frames from causing the underflow described above Signed-off-by: Neil Horman Tested-by: Andy Gospodarek Signed-off-by: David S. Miller --- drivers/net/e1000/e1000_main.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index b1419e21b46b..fffb006b7d95 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -4027,8 +4027,9 @@ static bool e1000_clean_rx_irq(struct e1000_adapter *adapter, PCI_DMA_FROMDEVICE); length = le16_to_cpu(rx_desc->length); - - if (unlikely(!(status & E1000_RXD_STAT_EOP))) { + /* !EOP means multiple descriptors were used to store a single + * packet, also make sure the frame isn't just CRC only */ + if (unlikely(!(status & E1000_RXD_STAT_EOP) || (length <= 4))) { /* All receives must fit into a single buffer */ E1000_DBG("%s: Receive packet consumed multiple" " buffers\n", netdev->name); -- cgit v1.2.3