From 0f9e980bf5ee1a97e2e401c846b2af989eb21c61 Mon Sep 17 00:00:00 2001 From: Konstantin Khlebnikov Date: Mon, 14 Jan 2019 16:29:30 +0300 Subject: e1000e: fix cyclic resets at link up with active tx I'm seeing series of e1000e resets (sometimes endless) at system boot if something generates tx traffic at this time. In my case this is netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames" from e1000e itself. As result e1000_watchdog_task sees used tx buffer while carrier is off and start this reset cycle again. [ 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000 [ 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 27.174495] 8021q: 802.1Q VLAN Support v1.8 [ 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1 [ 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation [ 30.898564] netpoll: netconsole: local port 6666 [ 30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8 [ 30.898567] netpoll: netconsole: interface 'eth1' [ 30.898568] netpoll: netconsole: remote port 6666 [ 30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790 [ 30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0 [ 30.917747] console [netcon0] enabled [ 30.917749] netconsole: network logging started [ 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None This patch flushes tx buffers only once when carrier is off rather than at each watchdog iteration. Signed-off-by: Konstantin Khlebnikov Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000e/netdev.c | 15 ++++++--------- 1 file changed, 6 insertions(+), 9 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index e19e53d97ac5..736fa51878f8 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -5309,8 +5309,13 @@ static void e1000_watchdog_task(struct work_struct *work) /* 8000ES2LAN requires a Rx packet buffer work-around * on link down event; reset the controller to flush * the Rx packet buffer. + * + * If the link is lost the controller stops DMA, but + * if there is queued Tx work it cannot be done. So + * reset the controller to flush the Tx packet buffers. */ - if (adapter->flags & FLAG_RX_NEEDS_RESTART) + if ((adapter->flags & FLAG_RX_NEEDS_RESTART) || + e1000_desc_unused(tx_ring) + 1 < tx_ring->count) adapter->flags |= FLAG_RESTART_NOW; else pm_schedule_suspend(netdev->dev.parent, @@ -5333,14 +5338,6 @@ link_up: adapter->gotc_old = adapter->stats.gotc; spin_unlock(&adapter->stats64_lock); - /* If the link is lost the controller stops DMA, but - * if there is queued Tx work it cannot be done. So - * reset the controller to flush the Tx packet buffers. - */ - if (!netif_carrier_ok(netdev) && - (e1000_desc_unused(tx_ring) + 1 < tx_ring->count)) - adapter->flags |= FLAG_RESTART_NOW; - /* If reset is necessary, do it outside of interrupt context. */ if (adapter->flags & FLAG_RESTART_NOW) { schedule_work(&adapter->reset_task); -- cgit v1.2.3