From dc8601a224d546bb321b058fc5ecabdb688a3582 Mon Sep 17 00:00:00 2001 From: Haojian Zhuang Date: Wed, 30 Dec 2009 02:27:24 -0500 Subject: [ARM] pxa: do not enable L2 after MMU is enabled Outer cache checked whether L2 is enabled or not. If L2 isn't enabled in XSC3, it would enable L2. This operation is evil that would make system hang. In XSC3 core document, these words are mentioned in below. "Following reset, the L2 Unified Cache Enable bit is cleared. To enable the L2 Cache, software may set the bit to a '1' before or at the same time as enabling the MMU. Enabling the L2 Cache after the MMU has been enabled or disabling the L2 Cache after the L2 Cache has been enabled, may result in unpredictable behavior of the processor." When outer cache is initialized, the MMU is already enabled. We couldn't enable L2 after MMU enabled. Signed-off-by: Haojian Zhuang Signed-off-by: Eric Miao --- arch/arm/mm/cache-xsc3l2.c | 11 +++++------ 1 file changed, 5 insertions(+), 6 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mm/cache-xsc3l2.c b/arch/arm/mm/cache-xsc3l2.c index 5d180cb0bd94..c3154928bccd 100644 --- a/arch/arm/mm/cache-xsc3l2.c +++ b/arch/arm/mm/cache-xsc3l2.c @@ -221,15 +221,14 @@ static int __init xsc3_l2_init(void) if (!cpu_is_xsc3() || !xsc3_l2_present()) return 0; - if (!(get_cr() & CR_L2)) { + if (get_cr() & CR_L2) { pr_info("XScale3 L2 cache enabled.\n"); - adjust_cr(CR_L2, CR_L2); xsc3_l2_inv_all(); - } - outer_cache.inv_range = xsc3_l2_inv_range; - outer_cache.clean_range = xsc3_l2_clean_range; - outer_cache.flush_range = xsc3_l2_flush_range; + outer_cache.inv_range = xsc3_l2_inv_range; + outer_cache.clean_range = xsc3_l2_clean_range; + outer_cache.flush_range = xsc3_l2_flush_range; + } return 0; } -- cgit v1.2.3 From 548c6af4627f4dcb24512a381193206e09bd6d31 Mon Sep 17 00:00:00 2001 From: Haojian Zhuang Date: Wed, 30 Dec 2009 10:02:57 -0500 Subject: [ARM] pxa: enable L2 if present in XSC3 Check whether L2 is present or not in XSC3. If it's present, enable L2 immediately. Disabling L2 after L2 is enabled that would result in unpredicatable behavior of XSC3 processor. Signed-off-by: Haojian Zhuang Signed-off-by: Eric Miao --- arch/arm/mm/proc-xsc3.S | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S index 96456f548798..8e4f6dca8997 100644 --- a/arch/arm/mm/proc-xsc3.S +++ b/arch/arm/mm/proc-xsc3.S @@ -407,6 +407,13 @@ __xsc3_setup: adr r5, xsc3_crval ldmia r5, {r5, r6} + +#ifdef CONFIG_CACHE_XSC3L2 + mrc p15, 1, r0, c0, c0, 1 @ get L2 present information + ands r0, r0, #0xf8 + orrne r6, r6, #(1 << 26) @ enable L2 if present +#endif + mrc p15, 0, r0, c1, c0, 0 @ get control register bic r0, r0, r5 @ ..V. ..R. .... ..A. orr r0, r0, r6 @ ..VI Z..S .... .C.M (mmu) -- cgit v1.2.3 From 2d51a521e64f91e42424b291fcae49d4d3f63d88 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Mon, 4 Jan 2010 11:42:01 +0800 Subject: [ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *' Signed-off-by: Eric Miao --- arch/arm/mach-pxa/magician.c | 2 +- arch/arm/mach-pxa/palmld.c | 2 +- arch/arm/mach-pxa/palmt5.c | 2 +- arch/arm/mach-pxa/palmtc.c | 2 +- arch/arm/mach-pxa/palmte2.c | 2 +- arch/arm/mach-pxa/palmtreo.c | 2 +- arch/arm/mach-pxa/palmtx.c | 2 +- arch/arm/mach-pxa/palmz72.c | 2 +- arch/arm/mach-pxa/viper.c | 2 +- 9 files changed, 9 insertions(+), 9 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c index 8a38d604dc77..189f330719a2 100644 --- a/arch/arm/mach-pxa/magician.c +++ b/arch/arm/mach-pxa/magician.c @@ -381,7 +381,7 @@ err: return ret; } -static int magician_backlight_notify(int brightness) +static int magician_backlight_notify(struct device *dev, int brightness) { gpio_set_value(EGPIO_MAGICIAN_BL_POWER, brightness); if (brightness >= 200) { diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c index 59140217890a..e100af78b166 100644 --- a/arch/arm/mach-pxa/palmld.c +++ b/arch/arm/mach-pxa/palmld.c @@ -270,7 +270,7 @@ err: return ret; } -static int palmld_backlight_notify(int brightness) +static int palmld_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMLD_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMLD_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c index 7f89ca20f13a..8fe3ec27568f 100644 --- a/arch/arm/mach-pxa/palmt5.c +++ b/arch/arm/mach-pxa/palmt5.c @@ -209,7 +209,7 @@ err: return ret; } -static int palmt5_backlight_notify(int brightness) +static int palmt5_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMT5_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMT5_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c index 308417592007..b992f07ece21 100644 --- a/arch/arm/mach-pxa/palmtc.c +++ b/arch/arm/mach-pxa/palmtc.c @@ -185,7 +185,7 @@ err: return ret; } -static int palmtc_backlight_notify(int brightness) +static int palmtc_backlight_notify(struct device *dev, int brightness) { /* backlight is on when GPIO16 AF0 is high */ gpio_set_value(GPIO_NR_PALMTC_BL_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmte2.c b/arch/arm/mach-pxa/palmte2.c index 265d62bae7de..dc728d6ab94e 100644 --- a/arch/arm/mach-pxa/palmte2.c +++ b/arch/arm/mach-pxa/palmte2.c @@ -181,7 +181,7 @@ err: return ret; } -static int palmte2_backlight_notify(int brightness) +static int palmte2_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMTE2_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMTE2_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c index 606eb7e8a17e..b433bb496711 100644 --- a/arch/arm/mach-pxa/palmtreo.c +++ b/arch/arm/mach-pxa/palmtreo.c @@ -375,7 +375,7 @@ err: return ret; } -static int treo_backlight_notify(int brightness) +static int treo_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_TREO_BL_POWER, brightness); return TREO_MAX_INTENSITY - brightness; diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c index 7bf18c2f002f..b37a025c0b7b 100644 --- a/arch/arm/mach-pxa/palmtx.c +++ b/arch/arm/mach-pxa/palmtx.c @@ -269,7 +269,7 @@ err: return ret; } -static int palmtx_backlight_notify(int brightness) +static int palmtx_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMTX_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMTX_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c index d787ac7cfdd8..1c5d68a94511 100644 --- a/arch/arm/mach-pxa/palmz72.c +++ b/arch/arm/mach-pxa/palmz72.c @@ -196,7 +196,7 @@ err: return ret; } -static int palmz72_backlight_notify(int brightness) +static int palmz72_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMZ72_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMZ72_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c index 5352b4e5a7dd..89f258c9e126 100644 --- a/arch/arm/mach-pxa/viper.c +++ b/arch/arm/mach-pxa/viper.c @@ -379,7 +379,7 @@ err_request_bckl: return ret; } -static int viper_backlight_notify(int brightness) +static int viper_backlight_notify(struct device *dev, int brightness) { gpio_set_value(VIPER_LCD_EN_GPIO, !!brightness); gpio_set_value(VIPER_BCKLIGHT_EN_GPIO, !!brightness); -- cgit v1.2.3 From 0dfc84c9f54d8784f5bc6d303c079d88000ee5f7 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Mon, 4 Jan 2010 14:44:42 +0800 Subject: [ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*() Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/hardware.h | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index 50f1297bf5ac..e741bf1bfb2d 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -250,20 +250,17 @@ #define cpu_is_pxa930() \ ({ \ - unsigned int id = read_cpuid(CPUID_ID); \ - __cpu_is_pxa930(id); \ + __cpu_is_pxa930(read_cpuid_id()); \ }) #define cpu_is_pxa935() \ ({ \ - unsigned int id = read_cpuid(CPUID_ID); \ - __cpu_is_pxa935(id); \ + __cpu_is_pxa935(read_cpuid_id()); \ }) #define cpu_is_pxa950() \ ({ \ - unsigned int id = read_cpuid(CPUID_ID); \ - __cpu_is_pxa950(id); \ + __cpu_is_pxa950(read_cpuid_id()); \ }) -- cgit v1.2.3 From 8784895ede9a39cfecf76fe26b090a602877f70f Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 7 Jan 2010 17:52:26 +0000 Subject: ARM: add missing recvmmsg syscall number Signed-off-by: Russell King --- arch/arm/include/asm/unistd.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h index 4e506d09e5f9..cf9cdaa2d4d4 100644 --- a/arch/arm/include/asm/unistd.h +++ b/arch/arm/include/asm/unistd.h @@ -391,6 +391,7 @@ #define __NR_pwritev (__NR_SYSCALL_BASE+362) #define __NR_rt_tgsigqueueinfo (__NR_SYSCALL_BASE+363) #define __NR_perf_event_open (__NR_SYSCALL_BASE+364) +#define __NR_recvmmsg (__NR_SYSCALL_BASE+365) /* * The following SWIs are ARM private. -- cgit v1.2.3 From d13fecd0293d55a4bcb8a31078216504192d8ce0 Mon Sep 17 00:00:00 2001 From: Cyril Hrubis Date: Thu, 7 Jan 2010 21:31:04 +0100 Subject: [ARM] pxa: fix strange characters in zaurus gpio .desc Somehow, strange characters made their way zaurus gpio .desc fields. Fix it. Signed-off-by: Pavel Machek Acked-by: Stanislav Brabec Signed-off-by: Eric Miao --- arch/arm/mach-pxa/spitz.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index 4b50f144fa48..28352c0b8c34 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -389,13 +389,13 @@ static struct gpio_keys_button spitz_gpio_keys[] = { .type = EV_SW, .code = 0, .gpio = SPITZ_GPIO_SWA, - .desc = "Display Down", + .desc = "Display Down", }, { .type = EV_SW, .code = 1, .gpio = SPITZ_GPIO_SWB, - .desc = "Lid Closed", + .desc = "Lid Closed", }, }; -- cgit v1.2.3 From 092a4e957a835cbf6b2ec82a6a4d6ff06c0a362e Mon Sep 17 00:00:00 2001 From: Jamie Iles Date: Wed, 6 Jan 2010 10:50:08 +0100 Subject: ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs Make registers unsigned for kernel space. This is important for example in the perf events where the PC is stored into a u64. We don't want it sign extended so make the regs unsigned to prevent casts throughout the kernel. Signed-off-by: Jamie Iles Signed-off-by: Russell King --- arch/arm/include/asm/ptrace.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/ptrace.h b/arch/arm/include/asm/ptrace.h index bbecccda76d0..eec6e897ceb2 100644 --- a/arch/arm/include/asm/ptrace.h +++ b/arch/arm/include/asm/ptrace.h @@ -97,9 +97,15 @@ * stack during a system call. Note that sizeof(struct pt_regs) * has to be a multiple of 8. */ +#ifndef __KERNEL__ struct pt_regs { long uregs[18]; }; +#else /* __KERNEL__ */ +struct pt_regs { + unsigned long uregs[18]; +}; +#endif /* __KERNEL__ */ #define ARM_cpsr uregs[16] #define ARM_pc uregs[15] -- cgit v1.2.3 From 406eb02029ea95545c08dba75da393fa47d3fb43 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 7 Jan 2010 11:25:42 +0100 Subject: ARM: 5867/1: Update U300 defconfig This updates the U300 defconfig to include the DMA driver merged in 2.6.33-rc1 and adds a codepage that's needed to mount VFAT MMC cards as default. The rest is new config options. Signed-off-by: Linus Walleij Signed-off-by: Russell King --- arch/arm/configs/u300_defconfig | 81 ++++++++++++++++++++++++++++++++++++----- 1 file changed, 71 insertions(+), 10 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/u300_defconfig b/arch/arm/configs/u300_defconfig index 610ac3c47b0f..9155196e623b 100644 --- a/arch/arm/configs/u300_defconfig +++ b/arch/arm/configs/u300_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.32-rc5 -# Sat Oct 17 23:32:24 2009 +# Linux kernel version: 2.6.33-rc2 +# Wed Jan 6 00:01:36 2010 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y @@ -46,6 +46,7 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_TREE_RCU=y # CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_TINY_RCU is not set # CONFIG_RCU_TRACE is not set CONFIG_RCU_FANOUT=32 # CONFIG_RCU_FANOUT_EXACT is not set @@ -119,14 +120,41 @@ CONFIG_BLOCK=y # IO Schedulers # CONFIG_IOSCHED_NOOP=y -# CONFIG_IOSCHED_AS is not set CONFIG_IOSCHED_DEADLINE=y # CONFIG_IOSCHED_CFQ is not set -# CONFIG_DEFAULT_AS is not set CONFIG_DEFAULT_DEADLINE=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="deadline" +# CONFIG_INLINE_SPIN_TRYLOCK is not set +# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set +# CONFIG_INLINE_SPIN_LOCK is not set +# CONFIG_INLINE_SPIN_LOCK_BH is not set +# CONFIG_INLINE_SPIN_LOCK_IRQ is not set +# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set +# CONFIG_INLINE_SPIN_UNLOCK is not set +# CONFIG_INLINE_SPIN_UNLOCK_BH is not set +# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set +# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set +# CONFIG_INLINE_READ_TRYLOCK is not set +# CONFIG_INLINE_READ_LOCK is not set +# CONFIG_INLINE_READ_LOCK_BH is not set +# CONFIG_INLINE_READ_LOCK_IRQ is not set +# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set +# CONFIG_INLINE_READ_UNLOCK is not set +# CONFIG_INLINE_READ_UNLOCK_BH is not set +# CONFIG_INLINE_READ_UNLOCK_IRQ is not set +# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set +# CONFIG_INLINE_WRITE_TRYLOCK is not set +# CONFIG_INLINE_WRITE_LOCK is not set +# CONFIG_INLINE_WRITE_LOCK_BH is not set +# CONFIG_INLINE_WRITE_LOCK_IRQ is not set +# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set +# CONFIG_INLINE_WRITE_UNLOCK is not set +# CONFIG_INLINE_WRITE_UNLOCK_BH is not set +# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set +# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set +# CONFIG_MUTEX_SPIN_ON_OWNER is not set # CONFIG_FREEZER is not set # @@ -155,6 +183,7 @@ CONFIG_MMU=y # CONFIG_ARCH_IXP2000 is not set # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_DOVE is not set # CONFIG_ARCH_KIRKWOOD is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set @@ -177,6 +206,7 @@ CONFIG_ARCH_U300=y # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set # CONFIG_ARCH_BCMRING is not set +# CONFIG_ARCH_U8500 is not set # # ST-Ericsson AB U300/U330/U335/U365 Platform @@ -265,12 +295,10 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_SPLIT_PTLOCK_CPUS=999999 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_HAVE_MLOCK=y -CONFIG_HAVE_MLOCKED_PAGE_BIT=y # CONFIG_KSM is not set CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_ALIGNMENT_TRAP=y @@ -499,14 +527,21 @@ CONFIG_MTD_NAND_IDS=y CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set # CONFIG_BLK_DEV_LOOP is not set + +# +# DRBD disabled because PROC_FS, INET or CONNECTOR not selected +# # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set CONFIG_MISC_DEVICES=y +# CONFIG_AD525X_DPOT is not set # CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_ISL29003 is not set +# CONFIG_DS1682 is not set +# CONFIG_TI_DAC7512 is not set # CONFIG_C2PORT is not set # @@ -517,6 +552,7 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_LEGACY is not set # CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_IWMC3200TOP is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -539,6 +575,7 @@ CONFIG_HAVE_IDE=y CONFIG_INPUT=y # CONFIG_INPUT_FF_MEMLESS is not set # CONFIG_INPUT_POLLDEV is not set +# CONFIG_INPUT_SPARSEKMAP is not set # # Userland interfaces @@ -645,7 +682,6 @@ CONFIG_I2C_STU300=y # # Miscellaneous I2C Chip support # -# CONFIG_DS1682 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -661,6 +697,8 @@ CONFIG_SPI_MASTER=y # CONFIG_SPI_BITBANG is not set # CONFIG_SPI_GPIO is not set CONFIG_SPI_PL022=y +# CONFIG_SPI_XILINX is not set +# CONFIG_SPI_DESIGNWARE is not set # # SPI Protocol Masters @@ -708,6 +746,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_T7L66XB is not set # CONFIG_MFD_TC6387XB is not set # CONFIG_PMIC_DA903X is not set +# CONFIG_PMIC_ADP5520 is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM831X is not set # CONFIG_MFD_WM8350_I2C is not set @@ -716,6 +755,8 @@ CONFIG_SSB_POSSIBLE=y CONFIG_AB3100_CORE=y CONFIG_AB3100_OTP=y # CONFIG_EZX_PCAP is not set +# CONFIG_MFD_88PM8607 is not set +# CONFIG_AB4500_CORE is not set CONFIG_REGULATOR=y # CONFIG_REGULATOR_DEBUG is not set # CONFIG_REGULATOR_FIXED_VOLTAGE is not set @@ -723,6 +764,7 @@ CONFIG_REGULATOR=y # CONFIG_REGULATOR_USERSPACE_CONSUMER is not set # CONFIG_REGULATOR_BQ24022 is not set # CONFIG_REGULATOR_MAX1586 is not set +# CONFIG_REGULATOR_MAX8660 is not set # CONFIG_REGULATOR_LP3971 is not set CONFIG_REGULATOR_AB3100=y # CONFIG_REGULATOR_TPS65023 is not set @@ -840,7 +882,9 @@ CONFIG_LEDS_CLASS=y # CONFIG_LEDS_LP3944 is not set # CONFIG_LEDS_PCA955X is not set # CONFIG_LEDS_DAC124S085 is not set +# CONFIG_LEDS_REGULATOR is not set # CONFIG_LEDS_BD2802 is not set +# CONFIG_LEDS_LT3593 is not set # # LED Triggers @@ -882,6 +926,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8563 is not set # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_BQ32K is not set # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set @@ -911,7 +956,9 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_M48T86 is not set # CONFIG_RTC_DRV_M48T35 is not set # CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_MSM6242 is not set # CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_RP5C01 is not set # CONFIG_RTC_DRV_V3020 is not set CONFIG_RTC_DRV_AB3100=y @@ -926,6 +973,15 @@ CONFIG_DMADEVICES=y # # DMA Devices # +CONFIG_COH901318=y +CONFIG_DMA_ENGINE=y + +# +# DMA Clients +# +# CONFIG_NET_DMA is not set +# CONFIG_ASYNC_TX_DMA is not set +# CONFIG_DMATEST is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set @@ -1018,7 +1074,7 @@ CONFIG_MISC_FILESYSTEMS=y CONFIG_MSDOS_PARTITION=y CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" -# CONFIG_NLS_CODEPAGE_437 is not set +CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set @@ -1135,6 +1191,7 @@ CONFIG_ARM_UNWIND=y # CONFIG_DEBUG_ERRORS is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_LL is not set +# CONFIG_OC_ETM is not set # # Security options @@ -1142,7 +1199,11 @@ CONFIG_ARM_UNWIND=y # CONFIG_KEYS is not set # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set -# CONFIG_SECURITY_FILE_CAPABILITIES is not set +# CONFIG_DEFAULT_SECURITY_SELINUX is not set +# CONFIG_DEFAULT_SECURITY_SMACK is not set +# CONFIG_DEFAULT_SECURITY_TOMOYO is not set +CONFIG_DEFAULT_SECURITY_DAC=y +CONFIG_DEFAULT_SECURITY="" # CONFIG_CRYPTO is not set # CONFIG_BINARY_PRINTF is not set -- cgit v1.2.3 From 22325525d8bb1478daddefec1b762e7882bcd515 Mon Sep 17 00:00:00 2001 From: Rabin Vincent Date: Fri, 8 Jan 2010 16:59:34 +0100 Subject: ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code" Fix the following warning, which appears when the register dump for a faulting process is printed in a kernel with SMP, DEBUG_PREEMPT, and DEBUG_USER (with user_debug=31) enabled: BUG: using smp_processor_id() in preemptible [00000000] code: init/1 caller is __show_regs+0x18/0x234 Backtrace: [] (dump_backtrace+0x0/0x114) from [] (dump_stack+0x18/0x1c) r6:c781a000 r5:c0157544 r4:00000001 r3:00000000 [] (dump_stack+0x0/0x1c) from [] (debug_smp_processor_id+0xc4/0xf8) [] (debug_smp_processor_id+0x0/0xf8) from [] (__show_regs+0x18/0x234) r6:c781bfb0 r5:00000000 r4:c781bfb0 r3:00000000 [] (__show_regs+0x0/0x234) from [] (show_regs+0x40/0x50) [] (show_regs+0x0/0x50) from [] (__do_user_fault+0x5c/0xa4) r4:c781c000 r3:00000000 [] (__do_user_fault+0x0/0xa4) from [] (do_page_fault+0x1b4/0x1e4) r7:00000000 r6:00010000 r5:c781bfb0 r4:c781c000 [] (do_page_fault+0x0/0x1e4) from [] (do_DataAbort+0x3c/0xa0) [] (do_DataAbort+0x0/0xa0) from [] (ret_from_exception+0x0/0x10) Signed-off-by: Rabin Vincent Signed-off-by: Russell King --- arch/arm/kernel/process.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 67304138a2ca..ba2adefa53f7 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -212,7 +212,8 @@ void __show_regs(struct pt_regs *regs) char buf[64]; printk("CPU: %d %s (%s %.*s)\n", - smp_processor_id(), print_tainted(), init_utsname()->release, + raw_smp_processor_id(), print_tainted(), + init_utsname()->release, (int)strcspn(init_utsname()->version, " "), init_utsname()->version); print_symbol("PC is at %s\n", instruction_pointer(regs)); -- cgit v1.2.3 From f892027c02f8d985455ba239ce280ac13b68a7fa Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Peter=20H=C3=BCwe?= Date: Sat, 9 Jan 2010 13:46:08 +0100 Subject: ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set A lot of ARM-defconfigs (those without CONFIG_ISA_DMA_API set) fail to build [1][2][3] due to the changes of the patch [PATCH] PCI: Clean up build for CONFIG_PCI_QUIRKS unset by Rafael J. Wysocki (Sat, 2 Jan 2010 22:57:24 +0100) [4] as the referenced variable 'isa_dma_bridge_buggy' in asm/dma.h is enclosed by the CONFIG_ISA_DMA_API conditional all configs without this setting fail to build. I'm not sure wether moving the condition is the right way to solve the issue, but atleast it fixes the issue :) References: [1] http://kisskb.ellerman.id.au/kisskb/buildresult/1983354/ [2] http://kisskb.ellerman.id.au/kisskb/buildresult/1983333/ [3] http://kisskb.ellerman.id.au/kisskb/buildresult/1983337/ [4] http://lkml.org/lkml/2010/1/2/102 Signed-off-by: Peter Huewe Signed-off-by: Russell King --- arch/arm/include/asm/dma.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/dma.h b/arch/arm/include/asm/dma.h index 7edf3536df24..ca51143f97f1 100644 --- a/arch/arm/include/asm/dma.h +++ b/arch/arm/include/asm/dma.h @@ -138,12 +138,12 @@ extern int get_dma_residue(unsigned int chan); #define NO_DMA 255 #endif +#endif /* CONFIG_ISA_DMA_API */ + #ifdef CONFIG_PCI extern int isa_dma_bridge_buggy; #else #define isa_dma_bridge_buggy (0) #endif -#endif /* CONFIG_ISA_DMA_API */ - #endif /* __ASM_ARM_DMA_H */ -- cgit v1.2.3 From 657b366a2827f35c020712e46696e56ab116d3c7 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Peter=20H=C3=BCwe?= Date: Sat, 9 Jan 2010 13:46:57 +0100 Subject: ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes This patch fixes a build failure [1] due to missing includes This should make the arm tree build again with lpd7a404_defconfig References: http://kisskb.ellerman.id.au/kisskb/buildresult/1983329/ Signed-off-by: Peter Huewe Signed-off-by: Russell King --- arch/arm/mach-lh7a40x/clocks.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-lh7a40x/clocks.c b/arch/arm/mach-lh7a40x/clocks.c index fcaf876f19b6..0651f96653f9 100644 --- a/arch/arm/mach-lh7a40x/clocks.c +++ b/arch/arm/mach-lh7a40x/clocks.c @@ -10,6 +10,8 @@ #include #include #include +#include +#include struct module; -- cgit v1.2.3 From 62a8c5bcb547c0aca1c3af810695dfb9b25e5351 Mon Sep 17 00:00:00 2001 From: Santosh Shilimkar Date: Sun, 10 Jan 2010 09:21:53 +0100 Subject: ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h The file arch/arm/include/asm/cpu.h needs to include 'linux/cpu.h' to meet its dependency. Otherwise when using "struct cpuinfo_arm" and including just 'asm/cpu.h' throws below error - arch/arm/include/asm/cpu.h:16: error: field 'cpu' has incomplete type To fix this otherway, one can also include both linux/cpu.h and asm/cpu.h but it shoudn't be that way. So this patch fixes this by including the linux/cpu.h in asm/cpu.h, so that including alone asm/cpu.h is enough. Signed-off-by: Santosh Shilimkar Signed-off-by: Russell King --- arch/arm/include/asm/cpu.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/cpu.h b/arch/arm/include/asm/cpu.h index 634b2d7c612a..793968173bef 100644 --- a/arch/arm/include/asm/cpu.h +++ b/arch/arm/include/asm/cpu.h @@ -11,6 +11,7 @@ #define __ASM_ARM_CPU_H #include +#include struct cpuinfo_arm { struct cpu cpu; -- cgit v1.2.3 From 4c9f8be7dab831c78b5f491739fc5cd01f2efb03 Mon Sep 17 00:00:00 2001 From: Colin Tuckley Date: Mon, 11 Jan 2010 11:09:15 +0100 Subject: ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards Extend the patch from Philby John to the other "RealView" boards. Rename the constants and offsets to reflect their actual functions. Cc: Philby John Signed-off-by: Colin Tuckley Acked-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/mach-realview/include/mach/board-pb1176.h | 4 ++-- arch/arm/mach-realview/include/mach/platform.h | 2 +- arch/arm/mach-realview/realview_eb.c | 15 +++++++++++++++ arch/arm/mach-realview/realview_pb1176.c | 10 ++++------ arch/arm/mach-realview/realview_pb11mp.c | 11 +++++------ arch/arm/mach-realview/realview_pba8.c | 15 +++++++++++++++ arch/arm/mach-realview/realview_pbx.c | 15 +++++++++++++++ 7 files changed, 57 insertions(+), 15 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-realview/include/mach/board-pb1176.h b/arch/arm/mach-realview/include/mach/board-pb1176.h index 34b80b7d40b8..2f5ccb298858 100644 --- a/arch/arm/mach-realview/include/mach/board-pb1176.h +++ b/arch/arm/mach-realview/include/mach/board-pb1176.h @@ -74,8 +74,8 @@ #define REALVIEW_PB1176_L220_BASE 0x10110000 /* L220 registers */ /* - * Control register SYS_RESETCTL is set to 1 to force a soft reset + * Control register SYS_RESETCTL Bit 8 is set to 1 to force a soft reset */ -#define REALVIEW_PB1176_SYS_LOCKVAL_RSTCTL 0x0100 +#define REALVIEW_PB1176_SYS_SOFT_RESET 0x0100 #endif /* __ASM_ARCH_BOARD_PB1176_H */ diff --git a/arch/arm/mach-realview/include/mach/platform.h b/arch/arm/mach-realview/include/mach/platform.h index 4f46bf71e752..86c0c4435a46 100644 --- a/arch/arm/mach-realview/include/mach/platform.h +++ b/arch/arm/mach-realview/include/mach/platform.h @@ -140,7 +140,7 @@ * SYS_CLD, SYS_BOOTCS */ #define REALVIEW_SYS_LOCK_LOCKED (1 << 16) -#define REALVIEW_SYS_LOCKVAL_MASK 0xA05F /* Enable write access */ +#define REALVIEW_SYS_LOCK_VAL 0xA05F /* Enable write access */ /* * REALVIEW_SYS_FLASH diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index 917f8ca3abff..7d857d300558 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -381,6 +381,20 @@ static struct sys_timer realview_eb_timer = { .init = realview_eb_timer_init, }; +static void realview_eb_reset(char mode) +{ + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); + + /* + * To reset, we hit the on-board reset register + * in the system FPGA + */ + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + if (core_tile_eb11mp()) + __raw_writel(0x0008, reset_ctrl); +} + static void __init realview_eb_init(void) { int i; @@ -408,6 +422,7 @@ static void __init realview_eb_init(void) #ifdef CONFIG_LEDS leds_event = realview_leds_event; #endif + realview_reset = realview_eb_reset; } MACHINE_START(REALVIEW_EB, "ARM-RealView EB") diff --git a/arch/arm/mach-realview/realview_pb1176.c b/arch/arm/mach-realview/realview_pb1176.c index 7fb726d5f8b9..44392e51dd50 100644 --- a/arch/arm/mach-realview/realview_pb1176.c +++ b/arch/arm/mach-realview/realview_pb1176.c @@ -292,12 +292,10 @@ static struct sys_timer realview_pb1176_timer = { static void realview_pb1176_reset(char mode) { - void __iomem *hdr_ctrl = __io_address(REALVIEW_SYS_BASE) + - REALVIEW_SYS_RESETCTL_OFFSET; - void __iomem *rst_hdr_ctrl = __io_address(REALVIEW_SYS_BASE) + - REALVIEW_SYS_LOCK_OFFSET; - __raw_writel(REALVIEW_SYS_LOCKVAL_MASK, rst_hdr_ctrl); - __raw_writel(REALVIEW_PB1176_SYS_LOCKVAL_RSTCTL, hdr_ctrl); + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + __raw_writel(REALVIEW_PB1176_SYS_SOFT_RESET, reset_ctrl); } static void realview_pb1176_fixup(struct machine_desc *mdesc, diff --git a/arch/arm/mach-realview/realview_pb11mp.c b/arch/arm/mach-realview/realview_pb11mp.c index 9bbbfc05f225..3e02731af959 100644 --- a/arch/arm/mach-realview/realview_pb11mp.c +++ b/arch/arm/mach-realview/realview_pb11mp.c @@ -301,17 +301,16 @@ static struct sys_timer realview_pb11mp_timer = { static void realview_pb11mp_reset(char mode) { - void __iomem *hdr_ctrl = __io_address(REALVIEW_SYS_BASE) + - REALVIEW_SYS_RESETCTL_OFFSET; - unsigned int val; + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); /* * To reset, we hit the on-board reset register * in the system FPGA */ - val = __raw_readl(hdr_ctrl); - val |= REALVIEW_PB11MP_SYS_CTRL_RESET_CONFIGCLR; - __raw_writel(val, hdr_ctrl); + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + __raw_writel(0x0000, reset_ctrl); + __raw_writel(0x0004, reset_ctrl); } static void __init realview_pb11mp_init(void) diff --git a/arch/arm/mach-realview/realview_pba8.c b/arch/arm/mach-realview/realview_pba8.c index fe861e96c566..fe4e25c4201a 100644 --- a/arch/arm/mach-realview/realview_pba8.c +++ b/arch/arm/mach-realview/realview_pba8.c @@ -272,6 +272,20 @@ static struct sys_timer realview_pba8_timer = { .init = realview_pba8_timer_init, }; +static void realview_pba8_reset(char mode) +{ + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); + + /* + * To reset, we hit the on-board reset register + * in the system FPGA + */ + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + __raw_writel(0x0000, reset_ctrl); + __raw_writel(0x0004, reset_ctrl); +} + static void __init realview_pba8_init(void) { int i; @@ -291,6 +305,7 @@ static void __init realview_pba8_init(void) #ifdef CONFIG_LEDS leds_event = realview_leds_event; #endif + realview_reset = realview_pba8_reset; } MACHINE_START(REALVIEW_PBA8, "ARM-RealView PB-A8") diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c index ec39488e2b42..a21a4b395f73 100644 --- a/arch/arm/mach-realview/realview_pbx.c +++ b/arch/arm/mach-realview/realview_pbx.c @@ -324,6 +324,20 @@ static void realview_pbx_fixup(struct machine_desc *mdesc, struct tag *tags, #endif } +static void realview_pbx_reset(char mode) +{ + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); + + /* + * To reset, we hit the on-board reset register + * in the system FPGA + */ + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + __raw_writel(0x0000, reset_ctrl); + __raw_writel(0x0004, reset_ctrl); +} + static void __init realview_pbx_init(void) { int i; @@ -358,6 +372,7 @@ static void __init realview_pbx_init(void) #ifdef CONFIG_LEDS leds_event = realview_leds_event; #endif + realview_reset = realview_pbx_reset; } MACHINE_START(REALVIEW_PBX, "ARM-RealView PBX") -- cgit v1.2.3 From 7511bce4069de39ea04b14c1e1d55c249f9ce808 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 12 Jan 2010 18:59:16 +0000 Subject: ARM: Fix wrong dmb The __kuser_cmpxchg code uses an ARMv6 dmb instruction, rather than one based upon the architecture being built for. Switch to using the macro provided for this purpose, which also eliminates the need for an ifdef. Acked-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/kernel/entry-armv.S | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index d2903e3bc861..6c5cf369183b 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -957,9 +957,7 @@ kuser_cmpxchg_fixup: #else -#ifdef CONFIG_SMP - mcr p15, 0, r0, c7, c10, 5 @ dmb -#endif + smp_dmb 1: ldrex r3, [r2] subs r3, r3, r0 strexeq r3, r1, [r2] -- cgit v1.2.3 From aff7b4f86737f1ae364bf5ece9a9b8586ddb2db4 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 12 Jan 2010 19:02:05 +0000 Subject: ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options A kernel with both ARMv6 and ARMv7 selected results in build errors. Fix this by specifying the proper architectures for these assembly files. Signed-off-by: Russell King --- arch/arm/mm/Makefile | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile index 827e238e5d4a..e8d34a80851c 100644 --- a/arch/arm/mm/Makefile +++ b/arch/arm/mm/Makefile @@ -27,6 +27,9 @@ obj-$(CONFIG_CPU_ABRT_EV5TJ) += abort-ev5tj.o obj-$(CONFIG_CPU_ABRT_EV6) += abort-ev6.o obj-$(CONFIG_CPU_ABRT_EV7) += abort-ev7.o +AFLAGS_abort-ev6.o :=-Wa,-march=armv6k +AFLAGS_abort-ev7.o :=-Wa,-march=armv7-a + obj-$(CONFIG_CPU_PABRT_LEGACY) += pabort-legacy.o obj-$(CONFIG_CPU_PABRT_V6) += pabort-v6.o obj-$(CONFIG_CPU_PABRT_V7) += pabort-v7.o @@ -39,6 +42,9 @@ obj-$(CONFIG_CPU_CACHE_V6) += cache-v6.o obj-$(CONFIG_CPU_CACHE_V7) += cache-v7.o obj-$(CONFIG_CPU_CACHE_FA) += cache-fa.o +AFLAGS_cache-v6.o :=-Wa,-march=armv6 +AFLAGS_cache-v7.o :=-Wa,-march=armv7-a + obj-$(CONFIG_CPU_COPY_V3) += copypage-v3.o obj-$(CONFIG_CPU_COPY_V4WT) += copypage-v4wt.o obj-$(CONFIG_CPU_COPY_V4WB) += copypage-v4wb.o @@ -58,6 +64,9 @@ obj-$(CONFIG_CPU_TLB_V6) += tlb-v6.o obj-$(CONFIG_CPU_TLB_V7) += tlb-v7.o obj-$(CONFIG_CPU_TLB_FA) += tlb-fa.o +AFLAGS_tlb-v6.o :=-Wa,-march=armv6 +AFLAGS_tlb-v7.o :=-Wa,-march=armv7-a + obj-$(CONFIG_CPU_ARM610) += proc-arm6_7.o obj-$(CONFIG_CPU_ARM710) += proc-arm6_7.o obj-$(CONFIG_CPU_ARM7TDMI) += proc-arm7tdmi.o @@ -84,6 +93,9 @@ obj-$(CONFIG_CPU_FEROCEON) += proc-feroceon.o obj-$(CONFIG_CPU_V6) += proc-v6.o obj-$(CONFIG_CPU_V7) += proc-v7.o +AFLAGS_proc-v6.o :=-Wa,-march=armv6 +AFLAGS_proc-v7.o :=-Wa,-march=armv7-a + obj-$(CONFIG_CACHE_FEROCEON_L2) += cache-feroceon-l2.o obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o obj-$(CONFIG_CACHE_XSC3L2) += cache-xsc3l2.o -- cgit v1.2.3