From 64ddba4d8a381b65bebee24c8da4eb80080c64a4 Mon Sep 17 00:00:00 2001 From: Mian Yousaf Kaukab Date: Mon, 29 Apr 2013 14:07:48 +0200 Subject: mtd: nand: fsmc: update of OF support Add nand bank selection and timings to the device tree bindings. Signed-off-by: Mian Yousaf Kaukab [Added some documentation] Signed-off-by: Linus Walleij Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- .../devicetree/bindings/mtd/fsmc-nand.txt | 25 +++++++++++++++++++++- 1 file changed, 24 insertions(+), 1 deletion(-) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index 2240ac09f6ba..ec42935f3908 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -1,4 +1,5 @@ -* FSMC NAND +ST Microelectronics Flexible Static Memory Controller (FSMC) +NAND Interface Required properties: - compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand" @@ -9,6 +10,26 @@ Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width defaults to 1 byte - nand-skip-bbtscan: Indicates the the BBT scanning should be skipped +- timings: array of 6 bytes for NAND timings. The meanings of these bytes + are: + byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits + are valid. Zero means one clockcycle, 15 means 16 clock + cycles. + byte 1 TAR : ALE to RE delay, 4 bits are valid. Same format as TCLR. + byte 2 THIZ : number of HCLK clock cycles during which the data bus is + kept in Hi-Z (tristate) after the start of a write access. + Only valid for write transactions. Zero means zero cycles, + 255 means 255 cycles. + byte 3 THOLD : number of HCLK clock cycles to hold the address (and data + when writing) after the command deassertation. Zero means + one cycle, 255 means 256 cycles. + byte 4 TWAIT : number of HCLK clock cycles to assert the command to the + NAND flash in response to SMWAITn. Zero means 1 cycle, + 255 means 256 cycles. + byte 5 TSET : number of HCLK clock cycles to assert the address before the + command is asserted. Zero means one cycle, 255 means 256 + cycles. +- bank: default NAND bank to use (0-3 are valid, 0 is the default). Example: @@ -24,6 +45,8 @@ Example: bank-width = <1>; nand-skip-bbtscan; + timings = /bits/ 8 <0 0 0 2 3 0>; + bank = <1>; partition@0 { ... -- cgit v1.2.3 From 1b7192658a08f70df0f290634fd7cd2ecb629fc9 Mon Sep 17 00:00:00 2001 From: Josh Wu Date: Thu, 9 May 2013 15:34:55 +0800 Subject: mtd: atmel_nand: add a new dt binding item for nand dma support This patch will set the nand dma support in dts. Since we will not use cpu_is_xxx() in nand driver. We needn't include the mach/cpu.h any more. Signed-off-by: Josh Wu Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- Documentation/devicetree/bindings/mtd/atmel-nand.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index d555421ea49f..b6eb484366a5 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -15,6 +15,7 @@ Required properties: optional gpio and may be set to 0 if not present. Optional properties: +- atmel,nand-has-dma : boolean to support dma transfer for nand read/write. - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", "soft_bch". -- cgit v1.2.3 From 7dc37de7d59cdd1c4cdd472e1994c31b16d7b874 Mon Sep 17 00:00:00 2001 From: Josh Wu Date: Mon, 5 Aug 2013 19:14:35 +0800 Subject: mtd: atmel_nand: add Nand Flash Controller (NFC) support Nand Flash Controller (NFC) can handle automatic transfers, sending the commands and address cycles to the NAND Flash. To use NFC in this driver, user needs to add NFC child node in nand flash driver. The NFC child node includes NFC's compatible string and regiters of the address and size of NFC command registers, NFC registers (embedded in HSMC) and NFC SRAM. Also user need to set up the HSMC irq, which use to check whether nfc command is finish or not. This driver has been tested on SAMA5D3X-EK board with JFFS2, YAFFS, UBIFS and mtd-utils. I put the part of the mtd_speedtest result here for your information. >From the mtd_speedtest, we can see the NFC will reduce the %50 of cpu load when writing nand flash. No change when reading. In the meantime, the speed will be slow about %8. - commands use to test: #insmod /mnt/mtd_speedtest.ko dev=2 & #top -n 30 -d 1 | grep speedtest - test result: Before the patch: ================================================= mtd_speedtest: MTD device: 2 mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64 515 495 root R 1164 0% 93% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 99% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock write speed is 5768 KiB/s mtd_speedtest: testing eraseblock read speed 515 495 root R 1164 0% 92% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock read speed is 5932 KiB/s mtd_speedtest: testing page write speed 515 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page write speed is 5770 KiB/s mtd_speedtest: testing page read speed 515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 89% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page read speed is 5910 KiB/s After the patch: ================================================= mtd_speedtest: MTD device: 2 mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64 mtd_speedtest: testing eraseblock write speed 509 495 root D 1164 0% 49% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 50% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 47% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock write speed is 5370 KiB/s mtd_speedtest: testing eraseblock read speed 509 495 root R 1164 0% 92% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 95% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock read speed is 5715 KiB/s mtd_speedtest: testing page write speed 509 495 root D 1164 0% 48% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 47% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 50% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page write speed is 5224 KiB/s mtd_speedtest: testing page read speed 509 495 root R 1164 0% 89% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 93% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page read speed is 5641 KiB/s Signed-off-by: Josh Wu Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- .../devicetree/bindings/mtd/atmel-nand.txt | 25 ++++++++++++++++++++++ 1 file changed, 25 insertions(+) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index b6eb484366a5..5d8b7d5c914d 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -30,6 +30,12 @@ Optional properties: sector size 1024. - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false +- Nand Flash Controller(NFC) is a slave driver under Atmel nand flash + - Required properties: + - compatible : "atmel,sama5d3-nfc". + - reg : should specify the address and size used for NFC command registers, + NFC registers and NFC Sram. NFC Sram address and size can be absent + if don't want to use it. Examples: nand0: nand@40000000,0 { @@ -78,3 +84,22 @@ nand0: nand@40000000 { ... }; }; + +/* for NFC supported chips */ +nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ... + nfc@70000000 { + compatible = "atmel,sama5d3-nfc"; + #address-cells = <1>; + #size-cells = <1>; + reg = < + 0x70000000 0x10000000 /* NFC Command Registers */ + 0xffffc000 0x00000070 /* NFC HSMC regs */ + 0x00200000 0x00100000 /* NFC SRAM banks */ + >; + }; +}; -- cgit v1.2.3 From 6054d4d56307839bffabb687767c24d5ff62563b Mon Sep 17 00:00:00 2001 From: Josh Wu Date: Mon, 5 Aug 2013 19:14:37 +0800 Subject: mtd: atmel_nand: enable Nand Flash Controller (NFC) write via sram This patch enable writing nand flash via NFC SRAM. It will minimize the CPU overhead. The SRAM write only support ECC_NONE and ECC_HW with PMECC. To enable this NFC write by SRAM feature, you can add a string in dts under NFC driver node. This driver has been tested on SAMA5D3X-EK with JFFS2, YAFFS2, UBIFS and mtd-utils. Here is part of mtd_speedtest (writing test) result, compare with non-NFC writing, it reduces %65 cpu load with loss %12 speed. - commands use to test: # insmod /mnt/mtd_speedtest.ko dev=2 & # top -n 30 -d 1 | grep speedtest - test result: ================================================= mtd_speedtest: MTD device: 2 mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64 mtd_speedtest: testing eraseblock write speed 509 495 root D 1164 0% 7% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 8% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 5% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock write speed is 5194 KiB/s mtd_speedtest: testing page write speed 509 495 root D 1164 0% 32% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 27% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 25% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 30% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page write speed is 5024 KiB/s Signed-off-by: Josh Wu Acked-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- Documentation/devicetree/bindings/mtd/atmel-nand.txt | 2 ++ 1 file changed, 2 insertions(+) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index 5d8b7d5c914d..c4728839d0c1 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -36,6 +36,8 @@ Optional properties: - reg : should specify the address and size used for NFC command registers, NFC registers and NFC Sram. NFC Sram address and size can be absent if don't want to use it. + - Optional properties: + - atmel,write-by-sram: boolean to enable NFC write by sram. Examples: nand0: nand@40000000,0 { -- cgit v1.2.3 From e79265ba6bdb31437bd4c3e7911950f9d1262a07 Mon Sep 17 00:00:00 2001 From: Josh Wu Date: Mon, 5 Aug 2013 19:14:38 +0800 Subject: mtd: ofpart: add compatible check for child nodes In case that the nand device will support some features like Nand Flash Controller, we want to make the sub feature as a sub node of nand device. Use such organization it is easy to enable/disable feature, also it is back compatible and more readable. If the sub-node has a compatible property then it is a driver not partition. Signed-off-by: Josh Wu Acked-by: Brian Norris Acked-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Artem Bityutskiy [ added a missing newline -Brian ] Signed-off-by: Brian Norris Signed-off-by: David Woodhouse --- Documentation/devicetree/bindings/mtd/partition.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index 9315ac96b49b..8e5557da1955 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -4,6 +4,7 @@ Partitions can be represented by sub-nodes of an mtd device. This can be used on platforms which have strong conventions about which portions of a flash are used for what purposes, but which don't use an on-flash partition table such as RedBoot. +NOTE: if the sub-node has a compatible string, then it is not a partition. #address-cells & #size-cells must both be present in the mtd device. There are two valid values for both: -- cgit v1.2.3 From dad2256269cb2ee3a72baefc5eb6e02ae1de2cfe Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Tue, 30 Jul 2013 17:53:00 -0700 Subject: mtd: nand: remove NAND_BBT_SCANEMPTY NAND_BBT_SCANEMPTY is a strange, badly-supported option with omap as its single remaining user. NAND_BBT_SCANEMPTY was likely used by accident in omap2[1]. And anyway, omap2 doesn't scan the chip for bad blocks (courtesy of NAND_SKIP_BBTSCAN), and so its use of this option is irrelevant. This patch drops the NAND_BBT_SCANEMPTY option. [1] http://lists.infradead.org/pipermail/linux-mtd/2012-July/042902.html Signed-off-by: Brian Norris Cc: Ivan Djelic Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- Documentation/DocBook/mtdnand.tmpl | 2 -- 1 file changed, 2 deletions(-) (limited to 'Documentation') diff --git a/Documentation/DocBook/mtdnand.tmpl b/Documentation/DocBook/mtdnand.tmpl index fe122d6e686f..a248f42a121e 100644 --- a/Documentation/DocBook/mtdnand.tmpl +++ b/Documentation/DocBook/mtdnand.tmpl @@ -1224,8 +1224,6 @@ in this page #define NAND_BBT_CREATE 0x00000200 /* Search good / bad pattern through all pages of a block */ #define NAND_BBT_SCANALLPAGES 0x00000400 -/* Scan block empty during good / bad block scan */ -#define NAND_BBT_SCANEMPTY 0x00000800 /* Write bbt if neccecary */ #define NAND_BBT_WRITE 0x00001000 /* Read and write back block contents when writing bbt */ -- cgit v1.2.3 From ed202940335e3f9930509025e3d75721e564baca Mon Sep 17 00:00:00 2001 From: Huang Shijie Date: Fri, 16 Aug 2013 10:10:09 +0800 Subject: mtd: update the ABI document about the ecc step size We add a new sys node for ecc step size. So update the ABI document about it. Signed-off-by: Huang Shijie Signed-off-by: Artem Bityutskiy [Brian: edited description, modified 'ecc_strength'] Signed-off-by: Brian Norris Signed-off-by: David Woodhouse --- Documentation/ABI/testing/sysfs-class-mtd | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) (limited to 'Documentation') diff --git a/Documentation/ABI/testing/sysfs-class-mtd b/Documentation/ABI/testing/sysfs-class-mtd index 3105644b3bfc..bfd119ace6ad 100644 --- a/Documentation/ABI/testing/sysfs-class-mtd +++ b/Documentation/ABI/testing/sysfs-class-mtd @@ -128,9 +128,8 @@ KernelVersion: 3.4 Contact: linux-mtd@lists.infradead.org Description: Maximum number of bit errors that the device is capable of - correcting within each region covering an ecc step. This will - always be a non-negative integer. Note that some devices will - have multiple ecc steps within each writesize region. + correcting within each region covering an ECC step (see + ecc_step_size). This will always be a non-negative integer. In the case of devices lacking any ECC capability, it is 0. @@ -173,3 +172,15 @@ Description: This is generally applicable only to NAND flash devices with ECC capability. It is ignored on devices lacking ECC capability; i.e., devices for which ecc_strength is zero. + +What: /sys/class/mtd/mtdX/ecc_step_size +Date: May 2013 +KernelVersion: 3.10 +Contact: linux-mtd@lists.infradead.org +Description: + The size of a single region covered by ECC, known as the ECC + step. Devices may have several equally sized ECC steps within + each writesize region. + + It will always be a non-negative integer. In the case of + devices lacking any ECC capability, it is 0. -- cgit v1.2.3