From fc3a1f04f5040255cbc086c419e4237f29f89f88 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 13 Dec 2011 18:34:01 +0100 Subject: gpio: add flags to export GPIOs when requesting Introduce new flags to automatically export GPIOs when using the convenience functions gpio_request_one() or gpio_request_array(). This eases support for custom boards where lots of GPIOs need to be exported for customer applications. Signed-off-by: Wolfram Sang Signed-off-by: Grant Likely --- Documentation/gpio.txt | 3 +++ 1 file changed, 3 insertions(+) (limited to 'Documentation') diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt index 620a07844e8c..e08a883de36e 100644 --- a/Documentation/gpio.txt +++ b/Documentation/gpio.txt @@ -322,6 +322,9 @@ where 'flags' is currently defined to specify the following properties: * GPIOF_OPEN_DRAIN - gpio pin is open drain type. * GPIOF_OPEN_SOURCE - gpio pin is open source type. + * GPIOF_EXPORT_DIR_FIXED - export gpio to sysfs, keep direction + * GPIOF_EXPORT_DIR_CHANGEABLE - also export, allow changing direction + since GPIOF_INIT_* are only valid when configured as output, so group valid combinations as: -- cgit v1.2.3 From e92935e13a052df7e6bc274e00fc91b80531f1e4 Mon Sep 17 00:00:00 2001 From: Roland Stigge Date: Fri, 18 May 2012 10:19:52 +0200 Subject: gpio/lpc32xx: Add device tree support This patch adds device tree support for gpio-lpc32xx.c. To register the various GPIO banks as (struct) gpio_chips via the same DT gpio-controller, we utilize the adjusted of_xlate API to manipulate the actually used struct gpio_chip. Signed-off-by: Roland Stigge Reviewed-by: Arnd Bergmann Signed-off-by: Grant Likely --- .../devicetree/bindings/gpio/gpio_lpc32xx.txt | 43 ++++++++++++++++++++++ 1 file changed, 43 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt new file mode 100644 index 000000000000..49819367a011 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt @@ -0,0 +1,43 @@ +NXP LPC32xx SoC GPIO controller + +Required properties: +- compatible: must be "nxp,lpc3220-gpio" +- reg: Physical base address and length of the controller's registers. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be 3: + 1) bank: + 0: GPIO P0 + 1: GPIO P1 + 2: GPIO P2 + 3: GPIO P3 + 4: GPI P3 + 5: GPO P3 + 2) pin number + 3) optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- reg: Index of the GPIO group + +Example: + + gpio: gpio@40028000 { + compatible = "nxp,lpc3220-gpio"; + reg = <0x40028000 0x1000>; + gpio-controller; + #gpio-cells = <3>; /* bank, pin, flags */ + }; + + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpio 5 1 1>; /* GPO_P3 1, active low */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + gpios = <&gpio 5 14 1>; /* GPO_P3 14, active low */ + linux,default-trigger = "timer"; + default-state = "off"; + }; + }; -- cgit v1.2.3