From ba2f55b06826fb51f15e3cb04b4457be5f66e0ef Mon Sep 17 00:00:00 2001 From: Heiner Kallweit Date: Sun, 11 Nov 2018 21:49:12 +0100 Subject: net: phy: icplus: add config_intr callback Move IRQ configuration for IP101A/G from config_init to config_intr callback. Reasons: 1. This allows phylib to disable interrupts if needed. 2. Icplus was the only driver supporting interrupts w/o defining a config_intr callback. Now we can add a phylib plausibility check disabling interrupt mode if one of the two irq-related callbacks isn't defined. I don't own hardware with this PHY, and the change is based on the datasheet for IP101A LF (which is supposed to be register-compatible with IP101A/G). Change is compile-tested only. Signed-off-by: Heiner Kallweit Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/phy/icplus.c | 23 ++++++++++++++++------- 1 file changed, 16 insertions(+), 7 deletions(-) diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c index 21ce68964204..ad87bd3280d7 100644 --- a/drivers/net/phy/icplus.c +++ b/drivers/net/phy/icplus.c @@ -42,8 +42,8 @@ MODULE_LICENSE("GPL"); #define IP1001_APS_ON 11 /* IP1001 APS Mode bit */ #define IP101A_G_APS_ON 2 /* IP101A/G APS Mode bit */ #define IP101A_G_IRQ_CONF_STATUS 0x11 /* Conf Info IRQ & Status Reg */ -#define IP101A_G_IRQ_PIN_USED (1<<15) /* INTR pin used */ -#define IP101A_G_IRQ_DEFAULT IP101A_G_IRQ_PIN_USED +#define IP101A_G_IRQ_PIN_USED BIT(15) /* INTR pin used */ +#define IP101A_G_NO_IRQ BIT(11) /* IRQ's inactive */ static int ip175c_config_init(struct phy_device *phydev) { @@ -170,11 +170,6 @@ static int ip101a_g_config_init(struct phy_device *phydev) if (c < 0) return c; - /* INTR pin used: speed/link/duplex will cause an interrupt */ - c = phy_write(phydev, IP101A_G_IRQ_CONF_STATUS, IP101A_G_IRQ_DEFAULT); - if (c < 0) - return c; - /* Enable Auto Power Saving mode */ c = phy_read(phydev, IP10XX_SPEC_CTRL_STATUS); c |= IP101A_G_APS_ON; @@ -201,6 +196,19 @@ static int ip175c_config_aneg(struct phy_device *phydev) return 0; } +static int ip101a_g_config_intr(struct phy_device *phydev) +{ + u16 val; + + if (phydev->interrupts == PHY_INTERRUPT_ENABLED) + /* INTR pin used: Speed/link/duplex will cause an interrupt */ + val = IP101A_G_IRQ_PIN_USED; + else + val = IP101A_G_NO_IRQ; + + return phy_write(phydev, IP101A_G_IRQ_CONF_STATUS, val); +} + static int ip101a_g_ack_interrupt(struct phy_device *phydev) { int err = phy_read(phydev, IP101A_G_IRQ_CONF_STATUS); @@ -234,6 +242,7 @@ static struct phy_driver icplus_driver[] = { .name = "ICPlus IP101A/G", .phy_id_mask = 0x0ffffff0, .features = PHY_BASIC_FEATURES, + .config_intr = ip101a_g_config_intr, .ack_interrupt = ip101a_g_ack_interrupt, .config_init = &ip101a_g_config_init, .suspend = genphy_suspend, -- cgit v1.2.3