From 1c552e08b29895d31bbf82bdb549811cfde31db4 Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:02 -0700
Subject: firmware: ti_sci: rm: Add support for tx_tdtype parameter for tx
 channel

The system controller's resource manager have support for configuring the
TDTYPE of TCHAN_CFG register on j721e.
With this parameter the teardown completion can be controlled:
TDTYPE == 0: Return without waiting for peer to complete the teardown
TDTYPE == 1: Wait for peer to complete the teardown

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/firmware/ti_sci.c              | 1 +
 drivers/firmware/ti_sci.h              | 7 +++++++
 include/linux/soc/ti/ti_sci_protocol.h | 2 ++
 3 files changed, 10 insertions(+)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 896f53ec7857..65a8c2e82093 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -2362,6 +2362,7 @@ static int ti_sci_cmd_rm_udmap_tx_ch_cfg(const struct ti_sci_handle *handle,
 	req->fdepth = params->fdepth;
 	req->tx_sched_priority = params->tx_sched_priority;
 	req->tx_burst_size = params->tx_burst_size;
+	req->tx_tdtype = params->tx_tdtype;
 
 	ret = ti_sci_do_xfer(info, xfer);
 	if (ret) {
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index 57cd04062994..dca19ca5fc49 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -910,6 +910,7 @@ struct rm_ti_sci_msg_udmap_rx_flow_opt_cfg {
  *   12 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_credit_count
  *   13 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::fdepth
  *   14 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_burst_size
+ *   15 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_tdtype
  *
  * @nav_id: SoC device ID of Navigator Subsystem where tx channel is located
  *
@@ -973,6 +974,11 @@ struct rm_ti_sci_msg_udmap_rx_flow_opt_cfg {
  *
  * @tx_burst_size: UDMAP transmit channel burst size configuration to be
  * programmed into the tx_burst_size field of the TCHAN_TCFG register.
+ *
+ * @tx_tdtype: UDMAP transmit channel teardown type configuration to be
+ * programmed into the tdtype field of the TCHAN_TCFG register:
+ * 0 - Return immediately
+ * 1 - Wait for completion message from remote peer
  */
 struct ti_sci_msg_rm_udmap_tx_ch_cfg_req {
 	struct ti_sci_msg_hdr hdr;
@@ -994,6 +1000,7 @@ struct ti_sci_msg_rm_udmap_tx_ch_cfg_req {
 	u16 fdepth;
 	u8 tx_sched_priority;
 	u8 tx_burst_size;
+	u8 tx_tdtype;
 } __packed;
 
 /**
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index cf27b080e148..d254d99fd45b 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -345,6 +345,7 @@ struct ti_sci_msg_rm_udmap_tx_ch_cfg {
 #define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_SUPR_TDPKT_VALID        BIT(11)
 #define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_CREDIT_COUNT_VALID      BIT(12)
 #define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_FDEPTH_VALID            BIT(13)
+#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_TDTYPE_VALID            BIT(15)
 	u16 nav_id;
 	u16 index;
 	u8 tx_pause_on_err;
@@ -362,6 +363,7 @@ struct ti_sci_msg_rm_udmap_tx_ch_cfg {
 	u16 fdepth;
 	u8 tx_sched_priority;
 	u8 tx_burst_size;
+	u8 tx_tdtype;
 };
 
 /**
-- 
cgit v1.2.3


From 967a020bd3deddf9a0af73aeb4d4b46d90030937 Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:03 -0700
Subject: firmware: ti_sci: Use struct ti_sci_resource_desc in get_range ops

Use the ti_sci_resource_desc directly and update it's start and num members
directly instead of requiring individual parameters for them.

This will allow easy extension of the RM parameters without changing API.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/firmware/ti_sci.c              | 32 +++++++++++++++-----------------
 include/linux/soc/ti/ti_sci_protocol.h | 32 ++++++++++++++++----------------
 2 files changed, 31 insertions(+), 33 deletions(-)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 65a8c2e82093..7a777e91ce3e 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -1703,14 +1703,14 @@ fail:
  * @subtype:		Resource assignment subtype that is being requested
  *			from the given device.
  * @s_host:		Host processor ID to which the resources are allocated
- * @range_start:	Start index of the resource range
- * @range_num:		Number of resources in the range
+ * @desc:		Pointer to ti_sci_resource_desc to be updated with the
+ *			resource range start index and number of resources
  *
  * Return: 0 if all went fine, else return appropriate error.
  */
 static int ti_sci_get_resource_range(const struct ti_sci_handle *handle,
 				     u32 dev_id, u8 subtype, u8 s_host,
-				     u16 *range_start, u16 *range_num)
+				     struct ti_sci_resource_desc *desc)
 {
 	struct ti_sci_msg_resp_get_resource_range *resp;
 	struct ti_sci_msg_req_get_resource_range *req;
@@ -1721,7 +1721,7 @@ static int ti_sci_get_resource_range(const struct ti_sci_handle *handle,
 
 	if (IS_ERR(handle))
 		return PTR_ERR(handle);
-	if (!handle)
+	if (!handle || !desc)
 		return -EINVAL;
 
 	info = handle_to_ti_sci_info(handle);
@@ -1754,8 +1754,8 @@ static int ti_sci_get_resource_range(const struct ti_sci_handle *handle,
 	} else if (!resp->range_start && !resp->range_num) {
 		ret = -ENODEV;
 	} else {
-		*range_start = resp->range_start;
-		*range_num = resp->range_num;
+		desc->start = resp->range_start;
+		desc->num = resp->range_num;
 	};
 
 fail:
@@ -1771,18 +1771,18 @@ fail:
  * @dev_id:		TISCI device ID.
  * @subtype:		Resource assignment subtype that is being requested
  *			from the given device.
- * @range_start:	Start index of the resource range
- * @range_num:		Number of resources in the range
+ * @desc:		Pointer to ti_sci_resource_desc to be updated with the
+ *			resource range start index and number of resources
  *
  * Return: 0 if all went fine, else return appropriate error.
  */
 static int ti_sci_cmd_get_resource_range(const struct ti_sci_handle *handle,
 					 u32 dev_id, u8 subtype,
-					 u16 *range_start, u16 *range_num)
+					 struct ti_sci_resource_desc *desc)
 {
 	return ti_sci_get_resource_range(handle, dev_id, subtype,
 					 TI_SCI_IRQ_SECONDARY_HOST_INVALID,
-					 range_start, range_num);
+					 desc);
 }
 
 /**
@@ -1793,18 +1793,17 @@ static int ti_sci_cmd_get_resource_range(const struct ti_sci_handle *handle,
  * @subtype:		Resource assignment subtype that is being requested
  *			from the given device.
  * @s_host:		Host processor ID to which the resources are allocated
- * @range_start:	Start index of the resource range
- * @range_num:		Number of resources in the range
+ * @desc:		Pointer to ti_sci_resource_desc to be updated with the
+ *			resource range start index and number of resources
  *
  * Return: 0 if all went fine, else return appropriate error.
  */
 static
 int ti_sci_cmd_get_resource_range_from_shost(const struct ti_sci_handle *handle,
 					     u32 dev_id, u8 subtype, u8 s_host,
-					     u16 *range_start, u16 *range_num)
+					     struct ti_sci_resource_desc *desc)
 {
-	return ti_sci_get_resource_range(handle, dev_id, subtype, s_host,
-					 range_start, range_num);
+	return ti_sci_get_resource_range(handle, dev_id, subtype, s_host, desc);
 }
 
 /**
@@ -3243,8 +3242,7 @@ devm_ti_sci_get_resource_sets(const struct ti_sci_handle *handle,
 	for (i = 0; i < res->sets; i++) {
 		ret = handle->ops.rm_core_ops.get_range(handle, dev_id,
 							sub_types[i],
-							&res->desc[i].start,
-							&res->desc[i].num);
+							&res->desc[i]);
 		if (ret) {
 			dev_dbg(dev, "dev = %d subtype %d not allocated for this host\n",
 				dev_id, sub_types[i]);
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index d254d99fd45b..6cd537db4d33 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -195,6 +195,18 @@ struct ti_sci_clk_ops {
 			u64 *current_freq);
 };
 
+/**
+ * struct ti_sci_resource_desc - Description of TI SCI resource instance range.
+ * @start:	Start index of the resource.
+ * @num:	Number of resources.
+ * @res_map:	Bitmap to manage the allocation of these resources.
+ */
+struct ti_sci_resource_desc {
+	u16 start;
+	u16 num;
+	unsigned long *res_map;
+};
+
 /**
  * struct ti_sci_rm_core_ops - Resource management core operations
  * @get_range:		Get a range of resources belonging to ti sci host.
@@ -209,15 +221,15 @@ struct ti_sci_clk_ops {
  * - dev_id:	TISCI device ID.
  * - subtype:	Resource assignment subtype that is being requested
  *		from the given device.
- * - range_start:	Start index of the resource range
- * - range_end:		Number of resources in the range
+ * - desc:	Pointer to ti_sci_resource_desc to be updated with the resource
+ *		range start index and number of resources
  */
 struct ti_sci_rm_core_ops {
 	int (*get_range)(const struct ti_sci_handle *handle, u32 dev_id,
-			 u8 subtype, u16 *range_start, u16 *range_num);
+			 u8 subtype, struct ti_sci_resource_desc *desc);
 	int (*get_range_from_shost)(const struct ti_sci_handle *handle,
 				    u32 dev_id, u8 subtype, u8 s_host,
-				    u16 *range_start, u16 *range_num);
+				    struct ti_sci_resource_desc *desc);
 };
 
 #define TI_SCI_RESASG_SUBTYPE_IR_OUTPUT		0
@@ -522,18 +534,6 @@ struct ti_sci_handle {
 
 #define TI_SCI_RESOURCE_NULL	0xffff
 
-/**
- * struct ti_sci_resource_desc - Description of TI SCI resource instance range.
- * @start:	Start index of the resource.
- * @num:	Number of resources.
- * @res_map:	Bitmap to manage the allocation of these resources.
- */
-struct ti_sci_resource_desc {
-	u16 start;
-	u16 num;
-	unsigned long *res_map;
-};
-
 /**
  * struct ti_sci_resource - Structure representing a resource assigned
  *			    to a device.
-- 
cgit v1.2.3


From 519c5c0c558b529f835c9bb30f9a1eb2034d585c Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:03 -0700
Subject: firmware: ti_sci: rm: Add support for second resource range

Sysfw added support for a second range in the resource range API to be able
to describe complex allocations mainly for DMA channels.

Update the ti_sci part to consider the second range as well.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/firmware/ti_sci.c              | 48 ++++++++++++++++++++++------------
 drivers/firmware/ti_sci.h              |  8 ++++--
 include/linux/soc/ti/ti_sci_protocol.h |  8 ++++--
 3 files changed, 43 insertions(+), 21 deletions(-)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 7a777e91ce3e..2793bb923881 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -1751,11 +1751,14 @@ static int ti_sci_get_resource_range(const struct ti_sci_handle *handle,
 
 	if (!ti_sci_is_response_ack(resp)) {
 		ret = -ENODEV;
-	} else if (!resp->range_start && !resp->range_num) {
+	} else if (!resp->range_num && !resp->range_num_sec) {
+		/* Neither of the two resource range is valid */
 		ret = -ENODEV;
 	} else {
 		desc->start = resp->range_start;
 		desc->num = resp->range_num;
+		desc->start_sec = resp->range_start_sec;
+		desc->num_sec = resp->range_num_sec;
 	};
 
 fail:
@@ -3157,12 +3160,18 @@ u16 ti_sci_get_free_resource(struct ti_sci_resource *res)
 
 	raw_spin_lock_irqsave(&res->lock, flags);
 	for (set = 0; set < res->sets; set++) {
-		free_bit = find_first_zero_bit(res->desc[set].res_map,
-					       res->desc[set].num);
-		if (free_bit != res->desc[set].num) {
-			set_bit(free_bit, res->desc[set].res_map);
+		struct ti_sci_resource_desc *desc = &res->desc[set];
+		int res_count = desc->num + desc->num_sec;
+
+		free_bit = find_first_zero_bit(desc->res_map, res_count);
+		if (free_bit != res_count) {
+			set_bit(free_bit, desc->res_map);
 			raw_spin_unlock_irqrestore(&res->lock, flags);
-			return res->desc[set].start + free_bit;
+
+			if (desc->num && free_bit < desc->num)
+				return desc->start + free_bit;
+			else
+				return desc->start_sec + free_bit;
 		}
 	}
 	raw_spin_unlock_irqrestore(&res->lock, flags);
@@ -3183,10 +3192,14 @@ void ti_sci_release_resource(struct ti_sci_resource *res, u16 id)
 
 	raw_spin_lock_irqsave(&res->lock, flags);
 	for (set = 0; set < res->sets; set++) {
-		if (res->desc[set].start <= id &&
-		    (res->desc[set].num + res->desc[set].start) > id)
-			clear_bit(id - res->desc[set].start,
-				  res->desc[set].res_map);
+		struct ti_sci_resource_desc *desc = &res->desc[set];
+
+		if (desc->num && desc->start <= id &&
+		    (desc->start + desc->num) > id)
+			clear_bit(id - desc->start, desc->res_map);
+		else if (desc->num_sec && desc->start_sec <= id &&
+			 (desc->start_sec + desc->num_sec) > id)
+			clear_bit(id - desc->start_sec, desc->res_map);
 	}
 	raw_spin_unlock_irqrestore(&res->lock, flags);
 }
@@ -3203,7 +3216,7 @@ u32 ti_sci_get_num_resources(struct ti_sci_resource *res)
 	u32 set, count = 0;
 
 	for (set = 0; set < res->sets; set++)
-		count += res->desc[set].num;
+		count += res->desc[set].num + res->desc[set].num_sec;
 
 	return count;
 }
@@ -3227,7 +3240,7 @@ devm_ti_sci_get_resource_sets(const struct ti_sci_handle *handle,
 {
 	struct ti_sci_resource *res;
 	bool valid_set = false;
-	int i, ret;
+	int i, ret, res_count;
 
 	res = devm_kzalloc(dev, sizeof(*res), GFP_KERNEL);
 	if (!res)
@@ -3246,18 +3259,19 @@ devm_ti_sci_get_resource_sets(const struct ti_sci_handle *handle,
 		if (ret) {
 			dev_dbg(dev, "dev = %d subtype %d not allocated for this host\n",
 				dev_id, sub_types[i]);
-			res->desc[i].start = 0;
-			res->desc[i].num = 0;
+			memset(&res->desc[i], 0, sizeof(res->desc[i]));
 			continue;
 		}
 
-		dev_dbg(dev, "dev = %d, subtype = %d, start = %d, num = %d\n",
+		dev_dbg(dev, "dev/sub_type: %d/%d, start/num: %d/%d | %d/%d\n",
 			dev_id, sub_types[i], res->desc[i].start,
-			res->desc[i].num);
+			res->desc[i].num, res->desc[i].start_sec,
+			res->desc[i].num_sec);
 
 		valid_set = true;
+		res_count = res->desc[i].num + res->desc[i].num_sec;
 		res->desc[i].res_map =
-			devm_kzalloc(dev, BITS_TO_LONGS(res->desc[i].num) *
+			devm_kzalloc(dev, BITS_TO_LONGS(res_count) *
 				     sizeof(*res->desc[i].res_map), GFP_KERNEL);
 		if (!res->desc[i].res_map)
 			return ERR_PTR(-ENOMEM);
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index dca19ca5fc49..4d980eb592c4 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -574,8 +574,10 @@ struct ti_sci_msg_req_get_resource_range {
 /**
  * struct ti_sci_msg_resp_get_resource_range - Response to resource get range.
  * @hdr:		Generic Header
- * @range_start:	Start index of the resource range.
- * @range_num:		Number of resources in the range.
+ * @range_start:	Start index of the first resource range.
+ * @range_num:		Number of resources in the first range.
+ * @range_start_sec:	Start index of the second resource range.
+ * @range_num_sec:	Number of resources in the second range.
  *
  * Response to request TI_SCI_MSG_GET_RESOURCE_RANGE.
  */
@@ -583,6 +585,8 @@ struct ti_sci_msg_resp_get_resource_range {
 	struct ti_sci_msg_hdr hdr;
 	u16 range_start;
 	u16 range_num;
+	u16 range_start_sec;
+	u16 range_num_sec;
 } __packed;
 
 /**
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 6cd537db4d33..9699b260de59 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -197,13 +197,17 @@ struct ti_sci_clk_ops {
 
 /**
  * struct ti_sci_resource_desc - Description of TI SCI resource instance range.
- * @start:	Start index of the resource.
- * @num:	Number of resources.
+ * @start:	Start index of the first resource range.
+ * @num:	Number of resources in the first range.
+ * @start_sec:	Start index of the second resource range.
+ * @num_sec:	Number of resources in the second range.
  * @res_map:	Bitmap to manage the allocation of these resources.
  */
 struct ti_sci_resource_desc {
 	u16 start;
 	u16 num;
+	u16 start_sec;
+	u16 num_sec;
 	unsigned long *res_map;
 };
 
-- 
cgit v1.2.3


From f5087f68e7a55fe7f8f257283ae8aecf1b8c3a76 Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:04 -0700
Subject: soc: ti: ti_sci_inta_msi: Add support for second range in resource
 ranges

Allocate MSI entries for both first and second range if they are valid

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/ti_sci_inta_msi.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/soc/ti/ti_sci_inta_msi.c b/drivers/soc/ti/ti_sci_inta_msi.c
index 0eb9462f609e..a1d9c027022a 100644
--- a/drivers/soc/ti/ti_sci_inta_msi.c
+++ b/drivers/soc/ti/ti_sci_inta_msi.c
@@ -89,6 +89,18 @@ static int ti_sci_inta_msi_alloc_descs(struct device *dev,
 			list_add_tail(&msi_desc->list, dev_to_msi_list(dev));
 			count++;
 		}
+		for (i = 0; i < res->desc[set].num_sec; i++) {
+			msi_desc = alloc_msi_entry(dev, 1, NULL);
+			if (!msi_desc) {
+				ti_sci_inta_msi_free_descs(dev);
+				return -ENOMEM;
+			}
+
+			msi_desc->inta.dev_index = res->desc[set].start_sec + i;
+			INIT_LIST_HEAD(&msi_desc->list);
+			list_add_tail(&msi_desc->list, dev_to_msi_list(dev));
+			count++;
+		}
 	}
 
 	return count;
-- 
cgit v1.2.3


From ce1feed58534d8489afb4900bee75dff15d950e0 Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:05 -0700
Subject: firmware: ti_sci: rm: Add support for extended_ch_type for tx channel

Sysfw added 'extended_ch_type' to the tx_ch_cfg_req message which should be
used when BCDMA block copy channels are configured:
extended_ch_type = 0 : the channel is split tx channel (tchan)
extended_ch_type = 1 : the channel is block copy channel (bchan)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/firmware/ti_sci.c              | 1 +
 drivers/firmware/ti_sci.h              | 6 ++++++
 include/linux/soc/ti/ti_sci_protocol.h | 5 +++++
 3 files changed, 12 insertions(+)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 2793bb923881..0dd3fbb4f964 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -2365,6 +2365,7 @@ static int ti_sci_cmd_rm_udmap_tx_ch_cfg(const struct ti_sci_handle *handle,
 	req->tx_sched_priority = params->tx_sched_priority;
 	req->tx_burst_size = params->tx_burst_size;
 	req->tx_tdtype = params->tx_tdtype;
+	req->extended_ch_type = params->extended_ch_type;
 
 	ret = ti_sci_do_xfer(info, xfer);
 	if (ret) {
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index 4d980eb592c4..ca15d8f1f8de 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -915,6 +915,7 @@ struct rm_ti_sci_msg_udmap_rx_flow_opt_cfg {
  *   13 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::fdepth
  *   14 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_burst_size
  *   15 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_tdtype
+ *   16 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::extended_ch_type
  *
  * @nav_id: SoC device ID of Navigator Subsystem where tx channel is located
  *
@@ -983,6 +984,10 @@ struct rm_ti_sci_msg_udmap_rx_flow_opt_cfg {
  * programmed into the tdtype field of the TCHAN_TCFG register:
  * 0 - Return immediately
  * 1 - Wait for completion message from remote peer
+ *
+ * @extended_ch_type: Valid for BCDMA.
+ * 0 - the channel is split tx channel (tchan)
+ * 1 - the channel is block copy channel (bchan)
  */
 struct ti_sci_msg_rm_udmap_tx_ch_cfg_req {
 	struct ti_sci_msg_hdr hdr;
@@ -1005,6 +1010,7 @@ struct ti_sci_msg_rm_udmap_tx_ch_cfg_req {
 	u8 tx_sched_priority;
 	u8 tx_burst_size;
 	u8 tx_tdtype;
+	u8 extended_ch_type;
 } __packed;
 
 /**
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 9699b260de59..6978afc00823 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -336,6 +336,9 @@ struct ti_sci_rm_psil_ops {
 #define TI_SCI_RM_UDMAP_CHAN_BURST_SIZE_128_BYTES	2
 #define TI_SCI_RM_UDMAP_CHAN_BURST_SIZE_256_BYTES	3
 
+#define TI_SCI_RM_BCDMA_EXTENDED_CH_TYPE_TCHAN		0
+#define TI_SCI_RM_BCDMA_EXTENDED_CH_TYPE_BCHAN		1
+
 /* UDMAP TX/RX channel valid_params common declarations */
 #define TI_SCI_MSG_VALUE_RM_UDMAP_CH_PAUSE_ON_ERR_VALID		BIT(0)
 #define TI_SCI_MSG_VALUE_RM_UDMAP_CH_ATYPE_VALID                BIT(1)
@@ -362,6 +365,7 @@ struct ti_sci_msg_rm_udmap_tx_ch_cfg {
 #define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_CREDIT_COUNT_VALID      BIT(12)
 #define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_FDEPTH_VALID            BIT(13)
 #define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_TDTYPE_VALID            BIT(15)
+#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_EXTENDED_CH_TYPE_VALID	BIT(16)
 	u16 nav_id;
 	u16 index;
 	u8 tx_pause_on_err;
@@ -380,6 +384,7 @@ struct ti_sci_msg_rm_udmap_tx_ch_cfg {
 	u8 tx_sched_priority;
 	u8 tx_burst_size;
 	u8 tx_tdtype;
+	u8 extended_ch_type;
 };
 
 /**
-- 
cgit v1.2.3


From 4d8ddf673a420aa25668eceeb4fbf33e2521fdf2 Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:05 -0700
Subject: firmware: ti_sci: rm: Remove ring_get_config support

The ring_get_cfg (0x1111 message) is not used and it is not supported by
sysfw for a long time.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/firmware/ti_sci.c              | 80 ----------------------------------
 drivers/firmware/ti_sci.h              | 44 -------------------
 include/linux/soc/ti/ti_sci_protocol.h |  6 ---
 3 files changed, 130 deletions(-)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 0dd3fbb4f964..0b801e67e672 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -2119,85 +2119,6 @@ fail:
 	return ret;
 }
 
-/**
- * ti_sci_cmd_ring_get_config() - get RA ring configuration
- * @handle:	Pointer to TI SCI handle.
- * @nav_id:	Device ID of Navigator Subsystem from which the ring is
- *		allocated
- * @index:	Ring index
- * @addr_lo:	Returns ring's base address lo 32 bits
- * @addr_hi:	Returns ring's base address hi 32 bits
- * @count:	Returns number of ring elements
- * @mode:	Returns mode of the ring
- * @size:	Returns ring element size
- * @order_id:	Returns ring's bus order ID
- *
- * Return: 0 if all went well, else returns appropriate error value.
- *
- * See @ti_sci_msg_rm_ring_get_cfg_req for more info.
- */
-static int ti_sci_cmd_ring_get_config(const struct ti_sci_handle *handle,
-				      u32 nav_id, u32 index, u8 *mode,
-				      u32 *addr_lo, u32 *addr_hi,
-				      u32 *count, u8 *size, u8 *order_id)
-{
-	struct ti_sci_msg_rm_ring_get_cfg_resp *resp;
-	struct ti_sci_msg_rm_ring_get_cfg_req *req;
-	struct ti_sci_xfer *xfer;
-	struct ti_sci_info *info;
-	struct device *dev;
-	int ret = 0;
-
-	if (IS_ERR_OR_NULL(handle))
-		return -EINVAL;
-
-	info = handle_to_ti_sci_info(handle);
-	dev = info->dev;
-
-	xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_RM_RING_GET_CFG,
-				   TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
-				   sizeof(*req), sizeof(*resp));
-	if (IS_ERR(xfer)) {
-		ret = PTR_ERR(xfer);
-		dev_err(dev,
-			"RM_RA:Message get config failed(%d)\n", ret);
-		return ret;
-	}
-	req = (struct ti_sci_msg_rm_ring_get_cfg_req *)xfer->xfer_buf;
-	req->nav_id = nav_id;
-	req->index = index;
-
-	ret = ti_sci_do_xfer(info, xfer);
-	if (ret) {
-		dev_err(dev, "RM_RA:Mbox get config send fail %d\n", ret);
-		goto fail;
-	}
-
-	resp = (struct ti_sci_msg_rm_ring_get_cfg_resp *)xfer->xfer_buf;
-
-	if (!ti_sci_is_response_ack(resp)) {
-		ret = -ENODEV;
-	} else {
-		if (mode)
-			*mode = resp->mode;
-		if (addr_lo)
-			*addr_lo = resp->addr_lo;
-		if (addr_hi)
-			*addr_hi = resp->addr_hi;
-		if (count)
-			*count = resp->count;
-		if (size)
-			*size = resp->size;
-		if (order_id)
-			*order_id = resp->order_id;
-	};
-
-fail:
-	ti_sci_put_one_xfer(&info->minfo, xfer);
-	dev_dbg(dev, "RM_RA:get config ring %u ret:%d\n", index, ret);
-	return ret;
-}
-
 /**
  * ti_sci_cmd_rm_psil_pair() - Pair PSI-L source to destination thread
  * @handle:	Pointer to TI SCI handle.
@@ -2926,7 +2847,6 @@ static void ti_sci_setup_ops(struct ti_sci_info *info)
 	iops->free_event_map = ti_sci_cmd_free_event_map;
 
 	rops->config = ti_sci_cmd_ring_config;
-	rops->get_config = ti_sci_cmd_ring_get_config;
 
 	psilops->pair = ti_sci_cmd_rm_psil_pair;
 	psilops->unpair = ti_sci_cmd_rm_psil_unpair;
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index ca15d8f1f8de..1cdf918be861 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -49,7 +49,6 @@
 #define TI_SCI_MSG_RM_RING_RECONFIG		0x1102
 #define TI_SCI_MSG_RM_RING_RESET		0x1103
 #define TI_SCI_MSG_RM_RING_CFG			0x1110
-#define TI_SCI_MSG_RM_RING_GET_CFG		0x1111
 
 /* PSI-L requests */
 #define TI_SCI_MSG_RM_PSIL_PAIR			0x1280
@@ -687,49 +686,6 @@ struct ti_sci_msg_rm_ring_cfg_req {
 	u8 order_id;
 } __packed;
 
-/**
- * struct ti_sci_msg_rm_ring_get_cfg_req - Get RA ring's configuration
- *
- * Gets the configuration of the non-real-time register fields of a ring.  The
- * host, or a supervisor of the host, who owns the ring must be the requesting
- * host.  The values of the non-real-time registers are returned in
- * @ti_sci_msg_rm_ring_get_cfg_resp.
- *
- * @hdr: Generic Header
- * @nav_id: Device ID of Navigator Subsystem from which the ring is allocated
- * @index: ring index.
- */
-struct ti_sci_msg_rm_ring_get_cfg_req {
-	struct ti_sci_msg_hdr hdr;
-	u16 nav_id;
-	u16 index;
-} __packed;
-
-/**
- * struct ti_sci_msg_rm_ring_get_cfg_resp -  Ring get configuration response
- *
- * Response received by host processor after RM has handled
- * @ti_sci_msg_rm_ring_get_cfg_req. The response contains the ring's
- * non-real-time register values.
- *
- * @hdr: Generic Header
- * @addr_lo: Ring 32 LSBs of base address
- * @addr_hi: Ring 16 MSBs of base address.
- * @count: Ring number of elements.
- * @mode: Ring mode.
- * @size: encoded Ring element size
- * @order_id: ing order ID.
- */
-struct ti_sci_msg_rm_ring_get_cfg_resp {
-	struct ti_sci_msg_hdr hdr;
-	u32 addr_lo;
-	u32 addr_hi;
-	u32 count;
-	u8 mode;
-	u8 size;
-	u8 order_id;
-} __packed;
-
 /**
  * struct ti_sci_msg_psil_pair - Pairs a PSI-L source thread to a destination
  *				 thread
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 6978afc00823..6710d7ac7a72 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -286,8 +286,6 @@ struct ti_sci_rm_irq_ops {
 /**
  * struct ti_sci_rm_ringacc_ops - Ring Accelerator Management operations
  * @config: configure the SoC Navigator Subsystem Ring Accelerator ring
- * @get_config: get the SoC Navigator Subsystem Ring Accelerator ring
- *		configuration
  */
 struct ti_sci_rm_ringacc_ops {
 	int (*config)(const struct ti_sci_handle *handle,
@@ -295,10 +293,6 @@ struct ti_sci_rm_ringacc_ops {
 		      u32 addr_lo, u32 addr_hi, u32 count, u8 mode,
 		      u8 size, u8 order_id
 	);
-	int (*get_config)(const struct ti_sci_handle *handle,
-			  u32 nav_id, u32 index, u8 *mode,
-			  u32 *addr_lo, u32 *addr_hi, u32 *count,
-			  u8 *size, u8 *order_id);
 };
 
 /**
-- 
cgit v1.2.3


From 3c2017536f3a122bf246cc87f9327e9ec138db92 Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:06 -0700
Subject: firmware: ti_sci: rm: Add new ops for ring configuration

The sysfw ring configuration message has been extended to include virtid
and asel value for the ring.
Add the ASEL_VALID to TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER as it is required
for DMA rings.

Instead of extending the current .config() ops - which would need same
patch change in the ringacc driver - add ti_sci_msg_rm_ring_cfg struct and
a new ops using it to configure the ring.

This will allow easy update path in case new members are added for the ring
configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/firmware/ti_sci.c              | 63 ++++++++++++++++++++++++++++++++++
 drivers/firmware/ti_sci.h              |  7 ++++
 include/linux/soc/ti/ti_sci_protocol.h | 31 ++++++++++++++++-
 3 files changed, 100 insertions(+), 1 deletion(-)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 0b801e67e672..a4d2b318795c 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -2119,6 +2119,68 @@ fail:
 	return ret;
 }
 
+/**
+ * ti_sci_cmd_rm_ring_cfg() - Configure a NAVSS ring
+ * @handle:	Pointer to TI SCI handle.
+ * @params:	Pointer to ti_sci_msg_rm_ring_cfg ring config structure
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ *
+ * See @ti_sci_msg_rm_ring_cfg and @ti_sci_msg_rm_ring_cfg_req for
+ * more info.
+ */
+static int ti_sci_cmd_rm_ring_cfg(const struct ti_sci_handle *handle,
+				  const struct ti_sci_msg_rm_ring_cfg *params)
+{
+	struct ti_sci_msg_rm_ring_cfg_req *req;
+	struct ti_sci_msg_hdr *resp;
+	struct ti_sci_xfer *xfer;
+	struct ti_sci_info *info;
+	struct device *dev;
+	int ret = 0;
+
+	if (IS_ERR_OR_NULL(handle))
+		return -EINVAL;
+
+	info = handle_to_ti_sci_info(handle);
+	dev = info->dev;
+
+	xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_RM_RING_CFG,
+				   TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+				   sizeof(*req), sizeof(*resp));
+	if (IS_ERR(xfer)) {
+		ret = PTR_ERR(xfer);
+		dev_err(dev, "RM_RA:Message config failed(%d)\n", ret);
+		return ret;
+	}
+	req = (struct ti_sci_msg_rm_ring_cfg_req *)xfer->xfer_buf;
+	req->valid_params = params->valid_params;
+	req->nav_id = params->nav_id;
+	req->index = params->index;
+	req->addr_lo = params->addr_lo;
+	req->addr_hi = params->addr_hi;
+	req->count = params->count;
+	req->mode = params->mode;
+	req->size = params->size;
+	req->order_id = params->order_id;
+	req->virtid = params->virtid;
+	req->asel = params->asel;
+
+	ret = ti_sci_do_xfer(info, xfer);
+	if (ret) {
+		dev_err(dev, "RM_RA:Mbox config send fail %d\n", ret);
+		goto fail;
+	}
+
+	resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+	ret = ti_sci_is_response_ack(resp) ? 0 : -EINVAL;
+
+fail:
+	ti_sci_put_one_xfer(&info->minfo, xfer);
+	dev_dbg(dev, "RM_RA:config ring %u ret:%d\n", params->index, ret);
+	return ret;
+}
+
 /**
  * ti_sci_cmd_rm_psil_pair() - Pair PSI-L source to destination thread
  * @handle:	Pointer to TI SCI handle.
@@ -2847,6 +2909,7 @@ static void ti_sci_setup_ops(struct ti_sci_info *info)
 	iops->free_event_map = ti_sci_cmd_free_event_map;
 
 	rops->config = ti_sci_cmd_ring_config;
+	rops->set_cfg = ti_sci_cmd_rm_ring_cfg;
 
 	psilops->pair = ti_sci_cmd_rm_psil_pair;
 	psilops->unpair = ti_sci_cmd_rm_psil_unpair;
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index 1cdf918be861..ef3a8214d002 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -659,6 +659,8 @@ struct ti_sci_msg_req_manage_irq {
  *	3 - Valid bit for @tisci_msg_rm_ring_cfg_req mode
  *	4 - Valid bit for @tisci_msg_rm_ring_cfg_req size
  *	5 - Valid bit for @tisci_msg_rm_ring_cfg_req order_id
+ *	6 - Valid bit for @tisci_msg_rm_ring_cfg_req virtid
+ *	7 - Valid bit for @tisci_msg_rm_ring_cfg_req ASEL
  * @nav_id: Device ID of Navigator Subsystem from which the ring is allocated
  * @index: ring index to be configured.
  * @addr_lo: 32 LSBs of ring base address to be programmed into the ring's
@@ -672,6 +674,9 @@ struct ti_sci_msg_req_manage_irq {
  *	the formula (log2(size_bytes) - 2), where size_bytes cannot be
  *	greater than 256.
  * @order_id: Specifies the ring's bus order ID.
+ * @virtid: Ring virt ID value
+ * @asel: Ring ASEL (address select) value to be set into the ASEL field of the
+ *	ring's RING_BA_HI register.
  */
 struct ti_sci_msg_rm_ring_cfg_req {
 	struct ti_sci_msg_hdr hdr;
@@ -684,6 +689,8 @@ struct ti_sci_msg_rm_ring_cfg_req {
 	u8 mode;
 	u8 size;
 	u8 order_id;
+	u16 virtid;
+	u8 asel;
 } __packed;
 
 /**
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 6710d7ac7a72..d1711050cd9d 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -275,17 +275,44 @@ struct ti_sci_rm_irq_ops {
 #define TI_SCI_MSG_VALUE_RM_RING_SIZE_VALID	BIT(4)
 /* RA config.order_id parameter is valid for RM ring configure TISCI message */
 #define TI_SCI_MSG_VALUE_RM_RING_ORDER_ID_VALID	BIT(5)
+/* RA config.virtid parameter is valid for RM ring configure TISCI message */
+#define TI_SCI_MSG_VALUE_RM_RING_VIRTID_VALID	BIT(6)
+/* RA config.asel parameter is valid for RM ring configure TISCI message */
+#define TI_SCI_MSG_VALUE_RM_RING_ASEL_VALID	BIT(7)
 
 #define TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER \
 	(TI_SCI_MSG_VALUE_RM_RING_ADDR_LO_VALID | \
 	TI_SCI_MSG_VALUE_RM_RING_ADDR_HI_VALID | \
 	TI_SCI_MSG_VALUE_RM_RING_COUNT_VALID | \
 	TI_SCI_MSG_VALUE_RM_RING_MODE_VALID | \
-	TI_SCI_MSG_VALUE_RM_RING_SIZE_VALID)
+	TI_SCI_MSG_VALUE_RM_RING_SIZE_VALID | \
+	TI_SCI_MSG_VALUE_RM_RING_ASEL_VALID)
+
+/**
+ * struct ti_sci_msg_rm_ring_cfg - Ring configuration
+ *
+ * Parameters for Navigator Subsystem ring configuration
+ * See @ti_sci_msg_rm_ring_cfg_req
+ */
+struct ti_sci_msg_rm_ring_cfg {
+	u32 valid_params;
+	u16 nav_id;
+	u16 index;
+	u32 addr_lo;
+	u32 addr_hi;
+	u32 count;
+	u8 mode;
+	u8 size;
+	u8 order_id;
+	u16 virtid;
+	u8 asel;
+};
 
 /**
  * struct ti_sci_rm_ringacc_ops - Ring Accelerator Management operations
  * @config: configure the SoC Navigator Subsystem Ring Accelerator ring
+ *	    Deprecated
+ * @set_cfg: configure the SoC Navigator Subsystem Ring Accelerator ring
  */
 struct ti_sci_rm_ringacc_ops {
 	int (*config)(const struct ti_sci_handle *handle,
@@ -293,6 +320,8 @@ struct ti_sci_rm_ringacc_ops {
 		      u32 addr_lo, u32 addr_hi, u32 count, u8 mode,
 		      u8 size, u8 order_id
 	);
+	int (*set_cfg)(const struct ti_sci_handle *handle,
+		       const struct ti_sci_msg_rm_ring_cfg *params);
 };
 
 /**
-- 
cgit v1.2.3


From bb49ca00bd8a42c327c23a21a46e86142b5734a2 Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:07 -0700
Subject: soc: ti: k3-ringacc: Use the ti_sci set_cfg callback for ring
 configuration

Switch to the new set_cfg to configure the ring.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/k3-ringacc.c | 79 ++++++++++++++++++---------------------------
 1 file changed, 32 insertions(+), 47 deletions(-)

diff --git a/drivers/soc/ti/k3-ringacc.c b/drivers/soc/ti/k3-ringacc.c
index 1147dc4c1d59..9ddd77113c5a 100644
--- a/drivers/soc/ti/k3-ringacc.c
+++ b/drivers/soc/ti/k3-ringacc.c
@@ -365,20 +365,16 @@ EXPORT_SYMBOL_GPL(k3_ringacc_request_rings_pair);
 
 static void k3_ringacc_ring_reset_sci(struct k3_ring *ring)
 {
+	struct ti_sci_msg_rm_ring_cfg ring_cfg = { 0 };
 	struct k3_ringacc *ringacc = ring->parent;
 	int ret;
 
-	ret = ringacc->tisci_ring_ops->config(
-			ringacc->tisci,
-			TI_SCI_MSG_VALUE_RM_RING_COUNT_VALID,
-			ringacc->tisci_dev_id,
-			ring->ring_id,
-			0,
-			0,
-			ring->size,
-			0,
-			0,
-			0);
+	ring_cfg.nav_id = ringacc->tisci_dev_id;
+	ring_cfg.index = ring->ring_id;
+	ring_cfg.valid_params = TI_SCI_MSG_VALUE_RM_RING_COUNT_VALID;
+	ring_cfg.count = ring->size;
+
+	ret = ringacc->tisci_ring_ops->set_cfg(ringacc->tisci, &ring_cfg);
 	if (ret)
 		dev_err(ringacc->dev, "TISCI reset ring fail (%d) ring_idx %d\n",
 			ret, ring->ring_id);
@@ -398,20 +394,16 @@ EXPORT_SYMBOL_GPL(k3_ringacc_ring_reset);
 static void k3_ringacc_ring_reconfig_qmode_sci(struct k3_ring *ring,
 					       enum k3_ring_mode mode)
 {
+	struct ti_sci_msg_rm_ring_cfg ring_cfg = { 0 };
 	struct k3_ringacc *ringacc = ring->parent;
 	int ret;
 
-	ret = ringacc->tisci_ring_ops->config(
-			ringacc->tisci,
-			TI_SCI_MSG_VALUE_RM_RING_MODE_VALID,
-			ringacc->tisci_dev_id,
-			ring->ring_id,
-			0,
-			0,
-			0,
-			mode,
-			0,
-			0);
+	ring_cfg.nav_id = ringacc->tisci_dev_id;
+	ring_cfg.index = ring->ring_id;
+	ring_cfg.valid_params = TI_SCI_MSG_VALUE_RM_RING_MODE_VALID;
+	ring_cfg.mode = mode;
+
+	ret = ringacc->tisci_ring_ops->set_cfg(ringacc->tisci, &ring_cfg);
 	if (ret)
 		dev_err(ringacc->dev, "TISCI reconf qmode fail (%d) ring_idx %d\n",
 			ret, ring->ring_id);
@@ -478,20 +470,15 @@ EXPORT_SYMBOL_GPL(k3_ringacc_ring_reset_dma);
 
 static void k3_ringacc_ring_free_sci(struct k3_ring *ring)
 {
+	struct ti_sci_msg_rm_ring_cfg ring_cfg = { 0 };
 	struct k3_ringacc *ringacc = ring->parent;
 	int ret;
 
-	ret = ringacc->tisci_ring_ops->config(
-			ringacc->tisci,
-			TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER,
-			ringacc->tisci_dev_id,
-			ring->ring_id,
-			0,
-			0,
-			0,
-			0,
-			0,
-			0);
+	ring_cfg.nav_id = ringacc->tisci_dev_id;
+	ring_cfg.index = ring->ring_id;
+	ring_cfg.valid_params = TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER;
+
+	ret = ringacc->tisci_ring_ops->set_cfg(ringacc->tisci, &ring_cfg);
 	if (ret)
 		dev_err(ringacc->dev, "TISCI ring free fail (%d) ring_idx %d\n",
 			ret, ring->ring_id);
@@ -575,28 +562,26 @@ EXPORT_SYMBOL_GPL(k3_ringacc_get_ring_irq_num);
 
 static int k3_ringacc_ring_cfg_sci(struct k3_ring *ring)
 {
+	struct ti_sci_msg_rm_ring_cfg ring_cfg = { 0 };
 	struct k3_ringacc *ringacc = ring->parent;
-	u32 ring_idx;
 	int ret;
 
 	if (!ringacc->tisci)
 		return -EINVAL;
 
-	ring_idx = ring->ring_id;
-	ret = ringacc->tisci_ring_ops->config(
-			ringacc->tisci,
-			TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER,
-			ringacc->tisci_dev_id,
-			ring_idx,
-			lower_32_bits(ring->ring_mem_dma),
-			upper_32_bits(ring->ring_mem_dma),
-			ring->size,
-			ring->mode,
-			ring->elm_size,
-			0);
+	ring_cfg.nav_id = ringacc->tisci_dev_id;
+	ring_cfg.index = ring->ring_id;
+	ring_cfg.valid_params = TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER;
+	ring_cfg.addr_lo = lower_32_bits(ring->ring_mem_dma);
+	ring_cfg.addr_hi = upper_32_bits(ring->ring_mem_dma);
+	ring_cfg.count = ring->size;
+	ring_cfg.mode = ring->mode;
+	ring_cfg.size = ring->elm_size;
+
+	ret = ringacc->tisci_ring_ops->set_cfg(ringacc->tisci, &ring_cfg);
 	if (ret)
 		dev_err(ringacc->dev, "TISCI config ring fail (%d) ring_idx %d\n",
-			ret, ring_idx);
+			ret, ring->ring_id);
 
 	return ret;
 }
-- 
cgit v1.2.3


From fed7552f1e69296461fca62ebaa0bb5a06fec0df Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:07 -0700
Subject: firmware: ti_sci: rm: Remove unused config() from
 ti_sci_rm_ringacc_ops

The ringacc driver has been converted to use the new set_cfg function to
configure the ring, the old config ops can be removed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/firmware/ti_sci.c              | 72 ----------------------------------
 include/linux/soc/ti/ti_sci_protocol.h |  7 ----
 2 files changed, 79 deletions(-)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index a4d2b318795c..235c7e7869aa 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -2048,77 +2048,6 @@ static int ti_sci_cmd_free_event_map(const struct ti_sci_handle *handle,
 			       ia_id, vint, global_event, vint_status_bit, 0);
 }
 
-/**
- * ti_sci_cmd_ring_config() - configure RA ring
- * @handle:		Pointer to TI SCI handle.
- * @valid_params:	Bitfield defining validity of ring configuration
- *			parameters
- * @nav_id:		Device ID of Navigator Subsystem from which the ring is
- *			allocated
- * @index:		Ring index
- * @addr_lo:		The ring base address lo 32 bits
- * @addr_hi:		The ring base address hi 32 bits
- * @count:		Number of ring elements
- * @mode:		The mode of the ring
- * @size:		The ring element size.
- * @order_id:		Specifies the ring's bus order ID
- *
- * Return: 0 if all went well, else returns appropriate error value.
- *
- * See @ti_sci_msg_rm_ring_cfg_req for more info.
- */
-static int ti_sci_cmd_ring_config(const struct ti_sci_handle *handle,
-				  u32 valid_params, u16 nav_id, u16 index,
-				  u32 addr_lo, u32 addr_hi, u32 count,
-				  u8 mode, u8 size, u8 order_id)
-{
-	struct ti_sci_msg_rm_ring_cfg_req *req;
-	struct ti_sci_msg_hdr *resp;
-	struct ti_sci_xfer *xfer;
-	struct ti_sci_info *info;
-	struct device *dev;
-	int ret = 0;
-
-	if (IS_ERR_OR_NULL(handle))
-		return -EINVAL;
-
-	info = handle_to_ti_sci_info(handle);
-	dev = info->dev;
-
-	xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_RM_RING_CFG,
-				   TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
-				   sizeof(*req), sizeof(*resp));
-	if (IS_ERR(xfer)) {
-		ret = PTR_ERR(xfer);
-		dev_err(dev, "RM_RA:Message config failed(%d)\n", ret);
-		return ret;
-	}
-	req = (struct ti_sci_msg_rm_ring_cfg_req *)xfer->xfer_buf;
-	req->valid_params = valid_params;
-	req->nav_id = nav_id;
-	req->index = index;
-	req->addr_lo = addr_lo;
-	req->addr_hi = addr_hi;
-	req->count = count;
-	req->mode = mode;
-	req->size = size;
-	req->order_id = order_id;
-
-	ret = ti_sci_do_xfer(info, xfer);
-	if (ret) {
-		dev_err(dev, "RM_RA:Mbox config send fail %d\n", ret);
-		goto fail;
-	}
-
-	resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
-	ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
-
-fail:
-	ti_sci_put_one_xfer(&info->minfo, xfer);
-	dev_dbg(dev, "RM_RA:config ring %u ret:%d\n", index, ret);
-	return ret;
-}
-
 /**
  * ti_sci_cmd_rm_ring_cfg() - Configure a NAVSS ring
  * @handle:	Pointer to TI SCI handle.
@@ -2908,7 +2837,6 @@ static void ti_sci_setup_ops(struct ti_sci_info *info)
 	iops->free_irq = ti_sci_cmd_free_irq;
 	iops->free_event_map = ti_sci_cmd_free_event_map;
 
-	rops->config = ti_sci_cmd_ring_config;
 	rops->set_cfg = ti_sci_cmd_rm_ring_cfg;
 
 	psilops->pair = ti_sci_cmd_rm_psil_pair;
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index d1711050cd9d..0aad7009b50e 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -310,16 +310,9 @@ struct ti_sci_msg_rm_ring_cfg {
 
 /**
  * struct ti_sci_rm_ringacc_ops - Ring Accelerator Management operations
- * @config: configure the SoC Navigator Subsystem Ring Accelerator ring
- *	    Deprecated
  * @set_cfg: configure the SoC Navigator Subsystem Ring Accelerator ring
  */
 struct ti_sci_rm_ringacc_ops {
-	int (*config)(const struct ti_sci_handle *handle,
-		      u32 valid_params, u16 nav_id, u16 index,
-		      u32 addr_lo, u32 addr_hi, u32 count, u8 mode,
-		      u8 size, u8 order_id
-	);
 	int (*set_cfg)(const struct ti_sci_handle *handle,
 		       const struct ti_sci_msg_rm_ring_cfg *params);
 };
-- 
cgit v1.2.3


From 8c42379e40e2db4199ceeb6a6ef9fff73ff132cf Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:22 -0700
Subject: soc: ti: k3-ringacc: Use correct device for allocation in RING mode

In RING mode the ringacc does not access the ring memory. In this access
mode the ringacc coherency does not have meaning.

If the ring is configured in RING mode, then the ringacc itself will not
access to the ring memory. Only the requester (user) of the ring is going
to read/write to the memory.
Extend the ring configuration parameters with a device pointer to be used
for DMA API when the ring is configured in RING mode.

Extending the ring configuration struct will allow per ring selection of
device to be used for allocation, thus allowing per ring coherency.

To avoid regression, fall back to use the ringacc dev in case the alloc_dev
is not provided.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/k3-ringacc.c       | 18 +++++++++++++-----
 include/linux/soc/ti/k3-ringacc.h |  5 +++++
 2 files changed, 18 insertions(+), 5 deletions(-)

diff --git a/drivers/soc/ti/k3-ringacc.c b/drivers/soc/ti/k3-ringacc.c
index 9ddd77113c5a..7fdb688452f7 100644
--- a/drivers/soc/ti/k3-ringacc.c
+++ b/drivers/soc/ti/k3-ringacc.c
@@ -141,6 +141,7 @@ struct k3_ring_state {
  * @parent: Pointer on struct @k3_ringacc
  * @use_count: Use count for shared rings
  * @proxy_id: RA Ring Proxy Id (only if @K3_RINGACC_RING_USE_PROXY)
+ * @dma_dev: device to be used for DMA API (allocation, mapping)
  */
 struct k3_ring {
 	struct k3_ring_rt_regs __iomem *rt;
@@ -160,6 +161,7 @@ struct k3_ring {
 	struct k3_ringacc	*parent;
 	u32		use_count;
 	int		proxy_id;
+	struct device	*dma_dev;
 };
 
 struct k3_ringacc_ops {
@@ -508,11 +510,12 @@ int k3_ringacc_ring_free(struct k3_ring *ring)
 
 	k3_ringacc_ring_free_sci(ring);
 
-	dma_free_coherent(ringacc->dev,
+	dma_free_coherent(ring->dma_dev,
 			  ring->size * (4 << ring->elm_size),
 			  ring->ring_mem_virt, ring->ring_mem_dma);
 	ring->flags = 0;
 	ring->ops = NULL;
+	ring->dma_dev = NULL;
 	if (ring->proxy_id != K3_RINGACC_PROXY_NOT_USED) {
 		clear_bit(ring->proxy_id, ringacc->proxy_inuse);
 		ring->proxy = NULL;
@@ -633,8 +636,12 @@ int k3_ringacc_ring_cfg(struct k3_ring *ring, struct k3_ring_cfg *cfg)
 	switch (ring->mode) {
 	case K3_RINGACC_RING_MODE_RING:
 		ring->ops = &k3_ring_mode_ring_ops;
+		ring->dma_dev = cfg->dma_dev;
+		if (!ring->dma_dev)
+			ring->dma_dev = ringacc->dev;
 		break;
 	case K3_RINGACC_RING_MODE_MESSAGE:
+		ring->dma_dev = ringacc->dev;
 		if (ring->proxy)
 			ring->ops = &k3_ring_mode_proxy_ops;
 		else
@@ -646,9 +653,9 @@ int k3_ringacc_ring_cfg(struct k3_ring *ring, struct k3_ring_cfg *cfg)
 		goto err_free_proxy;
 	}
 
-	ring->ring_mem_virt = dma_alloc_coherent(ringacc->dev,
-					ring->size * (4 << ring->elm_size),
-					&ring->ring_mem_dma, GFP_KERNEL);
+	ring->ring_mem_virt = dma_alloc_coherent(ring->dma_dev,
+						 ring->size * (4 << ring->elm_size),
+						 &ring->ring_mem_dma, GFP_KERNEL);
 	if (!ring->ring_mem_virt) {
 		dev_err(ringacc->dev, "Failed to alloc ring mem\n");
 		ret = -ENOMEM;
@@ -669,12 +676,13 @@ int k3_ringacc_ring_cfg(struct k3_ring *ring, struct k3_ring_cfg *cfg)
 	return 0;
 
 err_free_mem:
-	dma_free_coherent(ringacc->dev,
+	dma_free_coherent(ring->dma_dev,
 			  ring->size * (4 << ring->elm_size),
 			  ring->ring_mem_virt,
 			  ring->ring_mem_dma);
 err_free_ops:
 	ring->ops = NULL;
+	ring->dma_dev = NULL;
 err_free_proxy:
 	ring->proxy = NULL;
 	return ret;
diff --git a/include/linux/soc/ti/k3-ringacc.h b/include/linux/soc/ti/k3-ringacc.h
index 5a472eca5ee4..658dc71d2901 100644
--- a/include/linux/soc/ti/k3-ringacc.h
+++ b/include/linux/soc/ti/k3-ringacc.h
@@ -67,6 +67,9 @@ struct k3_ring;
  *	 few times. It's usable when the same ring is used as Free Host PD ring
  *	 for different flows, for example.
  *	 Note: Locking should be done by consumer if required
+ * @dma_dev: Master device which is using and accessing to the ring
+ *	memory when the mode is K3_RINGACC_RING_MODE_RING. Memory allocations
+ *	should be done using this device.
  */
 struct k3_ring_cfg {
 	u32 size;
@@ -74,6 +77,8 @@ struct k3_ring_cfg {
 	enum k3_ring_mode mode;
 #define K3_RINGACC_RING_SHARED BIT(1)
 	u32 flags;
+
+	struct device *dma_dev;
 };
 
 #define K3_RINGACC_RING_ID_ANY (-1)
-- 
cgit v1.2.3


From e643bd3809d4763cb85950782508f9a1ae78a8ac Mon Sep 17 00:00:00 2001
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Sun, 25 Oct 2020 12:10:23 -0700
Subject: soc: ti: k3-socinfo: Add entry for AM64X SoC family

It's JTAG PARTNO is 0xBB38.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/k3-socinfo.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/soc/ti/k3-socinfo.c b/drivers/soc/ti/k3-socinfo.c
index bbbc2d2b7091..fd91129de6e5 100644
--- a/drivers/soc/ti/k3-socinfo.c
+++ b/drivers/soc/ti/k3-socinfo.c
@@ -40,6 +40,7 @@ static const struct k3_soc_id {
 	{ 0xBB5A, "AM65X" },
 	{ 0xBB64, "J721E" },
 	{ 0xBB6D, "J7200" },
+	{ 0xBB38, "AM64X" }
 };
 
 static int
-- 
cgit v1.2.3


From ec8684847d8062496c4619bc3fcff31c19d56847 Mon Sep 17 00:00:00 2001
From: Zhang Qilong <zhangqilong3@huawei.com>
Date: Sat, 21 Nov 2020 19:22:00 -0800
Subject: soc: ti: knav_qmss: fix reference leak in knav_queue_probe

pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in knav_queue_probe, so we should fix it.

Fixes: 41f93af900a20 ("soc: ti: add Keystone Navigator QMSS driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/knav_qmss_queue.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/soc/ti/knav_qmss_queue.c b/drivers/soc/ti/knav_qmss_queue.c
index a460f201bf8e..54afa8f7f408 100644
--- a/drivers/soc/ti/knav_qmss_queue.c
+++ b/drivers/soc/ti/knav_qmss_queue.c
@@ -1784,6 +1784,7 @@ static int knav_queue_probe(struct platform_device *pdev)
 	pm_runtime_enable(&pdev->dev);
 	ret = pm_runtime_get_sync(&pdev->dev);
 	if (ret < 0) {
+		pm_runtime_put_noidle(&pdev->dev);
 		dev_err(dev, "Failed to enable QMSS\n");
 		return ret;
 	}
-- 
cgit v1.2.3


From fd79aebe5f7cc0bdc9656ddf1a52f04da9480cd7 Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Sat, 21 Nov 2020 19:22:00 -0800
Subject: soc: ti: omap-prm: Do not check rstst bit on deassert if already
 deasserted

If a rstctrl reset bit is already deasserted, we can just bail out early
not wait for rstst to clear. Otherwise we can have deassert fail for
already deasserted resets.

Fixes: c5117a78dd88 ("soc: ti: omap-prm: poll for reset complete during de-assert")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/omap_prm.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/soc/ti/omap_prm.c b/drivers/soc/ti/omap_prm.c
index 980b04c38fd9..4d41dc3cdce1 100644
--- a/drivers/soc/ti/omap_prm.c
+++ b/drivers/soc/ti/omap_prm.c
@@ -484,6 +484,10 @@ static int omap_reset_deassert(struct reset_controller_dev *rcdev,
 	struct ti_prm_platform_data *pdata = dev_get_platdata(reset->dev);
 	int ret = 0;
 
+	/* Nothing to do if the reset is already deasserted */
+	if (!omap_reset_status(rcdev, id))
+		return 0;
+
 	has_rstst = reset->prm->data->rstst ||
 		(reset->prm->data->flags & OMAP_PRM_HAS_RSTST);
 
-- 
cgit v1.2.3


From e72501099c4c8308aa5f1a7eed92a0839ab0cbbd Mon Sep 17 00:00:00 2001
From: Lee Jones <lee.jones@linaro.org>
Date: Sat, 21 Nov 2020 19:22:00 -0800
Subject: soc: ti: knav_qmss_queue: Remove set but unchecked variable 'ret'
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Fixes the following W=1 kernel build warning(s):

 drivers/soc/ti/knav_qmss_queue.c: In function ‘knav_setup_queue_pools’:
 drivers/soc/ti/knav_qmss_queue.c:1310:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]

Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/knav_qmss_queue.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/soc/ti/knav_qmss_queue.c b/drivers/soc/ti/knav_qmss_queue.c
index 54afa8f7f408..eb4cca430038 100644
--- a/drivers/soc/ti/knav_qmss_queue.c
+++ b/drivers/soc/ti/knav_qmss_queue.c
@@ -1307,12 +1307,11 @@ static int knav_setup_queue_pools(struct knav_device *kdev,
 				   struct device_node *queue_pools)
 {
 	struct device_node *type, *range;
-	int ret;
 
 	for_each_child_of_node(queue_pools, type) {
 		for_each_child_of_node(type, range) {
-			ret = knav_setup_queue_range(kdev, range);
 			/* return value ignored, we init the rest... */
+			knav_setup_queue_range(kdev, range);
 		}
 	}
 
-- 
cgit v1.2.3


From e8ebf411966f65d74693d21bd7b2ea7554a36b19 Mon Sep 17 00:00:00 2001
From: Lee Jones <lee.jones@linaro.org>
Date: Sat, 21 Nov 2020 19:22:00 -0800
Subject: soc: ti: knav_qmss_queue: Fix a whole host of function documentation
 issues

Fixes the following W=1 kernel build warning(s):

 drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'flags' not described in 'knav_queue_open'
 drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'id' not described in 'knav_queue_open'
 drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'name' not described in 'knav_queue_open'
 drivers/soc/ti/knav_qmss_queue.c:551: warning: Excess function parameter 'qh' description in 'knav_queue_close'
 drivers/soc/ti/knav_qmss_queue.c:551: warning: Function parameter or member 'qhandle' not described in 'knav_queue_close'
 drivers/soc/ti/knav_qmss_queue.c:583: warning: Excess function parameter 'qh' description in 'knav_queue_device_control'
 drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'arg' not described in 'knav_queue_device_control'
 drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'cmd' not described in 'knav_queue_device_control'
 drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'qhandle' not described in 'knav_queue_device_control'
 drivers/soc/ti/knav_qmss_queue.c:635: warning: Excess function parameter 'data' description in 'knav_queue_push'
 drivers/soc/ti/knav_qmss_queue.c:635: warning: Excess function parameter 'qh' description in 'knav_queue_push'
 drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'dma' not described in 'knav_queue_push'
 drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'flags' not described in 'knav_queue_push'
 drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'qhandle' not described in 'knav_queue_push'
 drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'size' not described in 'knav_queue_push'
 drivers/soc/ti/knav_qmss_queue.c:655: warning: Excess function parameter 'qh' description in 'knav_queue_pop'
 drivers/soc/ti/knav_qmss_queue.c:655: warning: Function parameter or member 'qhandle' not described in 'knav_queue_pop'
 drivers/soc/ti/knav_qmss_queue.c:655: warning: Function parameter or member 'size' not described in 'knav_queue_pop'
 drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'name' not described in 'knav_pool_create'
 drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'num_desc' not described in 'knav_pool_create'
 drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'region_id' not described in 'knav_pool_create'
 drivers/soc/ti/knav_qmss_queue.c:862: warning: Excess function parameter 'pool' description in 'knav_pool_destroy'
 drivers/soc/ti/knav_qmss_queue.c:862: warning: Function parameter or member 'ph' not described in 'knav_pool_destroy'
 drivers/soc/ti/knav_qmss_queue.c:892: warning: Excess function parameter 'pool' description in 'knav_pool_desc_get'
 drivers/soc/ti/knav_qmss_queue.c:892: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_get'
 drivers/soc/ti/knav_qmss_queue.c:911: warning: Excess function parameter 'pool' description in 'knav_pool_desc_put'
 drivers/soc/ti/knav_qmss_queue.c:911: warning: Function parameter or member 'desc' not described in 'knav_pool_desc_put'
 drivers/soc/ti/knav_qmss_queue.c:911: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_put'
 drivers/soc/ti/knav_qmss_queue.c:931: warning: Excess function parameter 'pool' description in 'knav_pool_desc_map'
 drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'desc' not described in 'knav_pool_desc_map'
 drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'dma' not described in 'knav_pool_desc_map'
 drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'dma_sz' not described in 'knav_pool_desc_map'
 drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_map'
 drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'size' not described in 'knav_pool_desc_map'
 drivers/soc/ti/knav_qmss_queue.c:956: warning: Excess function parameter 'pool' description in 'knav_pool_desc_unmap'
 drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'dma' not described in 'knav_pool_desc_unmap'
 drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'dma_sz' not described in 'knav_pool_desc_unmap'
 drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_unmap'
 drivers/soc/ti/knav_qmss_queue.c:975: warning: Excess function parameter 'pool' description in 'knav_pool_count'
 drivers/soc/ti/knav_qmss_queue.c:975: warning: Function parameter or member 'ph' not described in 'knav_pool_count'

Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/knav_qmss_queue.c | 59 ++++++++++++++++++++--------------------
 1 file changed, 30 insertions(+), 29 deletions(-)

diff --git a/drivers/soc/ti/knav_qmss_queue.c b/drivers/soc/ti/knav_qmss_queue.c
index eb4cca430038..490423ecdcdd 100644
--- a/drivers/soc/ti/knav_qmss_queue.c
+++ b/drivers/soc/ti/knav_qmss_queue.c
@@ -79,7 +79,7 @@ EXPORT_SYMBOL_GPL(knav_qmss_device_ready);
 /**
  * knav_queue_notify: qmss queue notfier call
  *
- * @inst:		qmss queue instance like accumulator
+ * @inst:		- qmss queue instance like accumulator
  */
 void knav_queue_notify(struct knav_queue_inst *inst)
 {
@@ -511,10 +511,10 @@ static int knav_queue_flush(struct knav_queue *qh)
 
 /**
  * knav_queue_open()	- open a hardware queue
- * @name		- name to give the queue handle
- * @id			- desired queue number if any or specifes the type
+ * @name:		- name to give the queue handle
+ * @id:			- desired queue number if any or specifes the type
  *			  of queue
- * @flags		- the following flags are applicable to queues:
+ * @flags:		- the following flags are applicable to queues:
  *	KNAV_QUEUE_SHARED - allow the queue to be shared. Queues are
  *			     exclusive by default.
  *			     Subsequent attempts to open a shared queue should
@@ -545,7 +545,7 @@ EXPORT_SYMBOL_GPL(knav_queue_open);
 
 /**
  * knav_queue_close()	- close a hardware queue handle
- * @qh			- handle to close
+ * @qhandle:		- handle to close
  */
 void knav_queue_close(void *qhandle)
 {
@@ -572,9 +572,9 @@ EXPORT_SYMBOL_GPL(knav_queue_close);
 
 /**
  * knav_queue_device_control()	- Perform control operations on a queue
- * @qh				- queue handle
- * @cmd				- control commands
- * @arg				- command argument
+ * @qhandle:			- queue handle
+ * @cmd:			- control commands
+ * @arg:			- command argument
  *
  * Returns 0 on success, errno otherwise.
  */
@@ -623,10 +623,10 @@ EXPORT_SYMBOL_GPL(knav_queue_device_control);
 
 /**
  * knav_queue_push()	- push data (or descriptor) to the tail of a queue
- * @qh			- hardware queue handle
- * @data		- data to push
- * @size		- size of data to push
- * @flags		- can be used to pass additional information
+ * @qhandle:		- hardware queue handle
+ * @dma:		- DMA data to push
+ * @size:		- size of data to push
+ * @flags:		- can be used to pass additional information
  *
  * Returns 0 on success, errno otherwise.
  */
@@ -646,8 +646,8 @@ EXPORT_SYMBOL_GPL(knav_queue_push);
 
 /**
  * knav_queue_pop()	- pop data (or descriptor) from the head of a queue
- * @qh			- hardware queue handle
- * @size		- (optional) size of the data pop'ed.
+ * @qhandle:		- hardware queue handle
+ * @size:		- (optional) size of the data pop'ed.
  *
  * Returns a DMA address on success, 0 on failure.
  */
@@ -746,9 +746,9 @@ EXPORT_SYMBOL_GPL(knav_pool_desc_dma_to_virt);
 
 /**
  * knav_pool_create()	- Create a pool of descriptors
- * @name		- name to give the pool handle
- * @num_desc		- numbers of descriptors in the pool
- * @region_id		- QMSS region id from which the descriptors are to be
+ * @name:		- name to give the pool handle
+ * @num_desc:		- numbers of descriptors in the pool
+ * @region_id:		- QMSS region id from which the descriptors are to be
  *			  allocated.
  *
  * Returns a pool handle on success.
@@ -856,7 +856,7 @@ EXPORT_SYMBOL_GPL(knav_pool_create);
 
 /**
  * knav_pool_destroy()	- Free a pool of descriptors
- * @pool		- pool handle
+ * @ph:		- pool handle
  */
 void knav_pool_destroy(void *ph)
 {
@@ -884,7 +884,7 @@ EXPORT_SYMBOL_GPL(knav_pool_destroy);
 
 /**
  * knav_pool_desc_get()	- Get a descriptor from the pool
- * @pool			- pool handle
+ * @ph:		- pool handle
  *
  * Returns descriptor from the pool.
  */
@@ -905,7 +905,8 @@ EXPORT_SYMBOL_GPL(knav_pool_desc_get);
 
 /**
  * knav_pool_desc_put()	- return a descriptor to the pool
- * @pool			- pool handle
+ * @ph:		- pool handle
+ * @desc:	- virtual address
  */
 void knav_pool_desc_put(void *ph, void *desc)
 {
@@ -918,11 +919,11 @@ EXPORT_SYMBOL_GPL(knav_pool_desc_put);
 
 /**
  * knav_pool_desc_map()	- Map descriptor for DMA transfer
- * @pool			- pool handle
- * @desc			- address of descriptor to map
- * @size			- size of descriptor to map
- * @dma				- DMA address return pointer
- * @dma_sz			- adjusted return pointer
+ * @ph:				- pool handle
+ * @desc:			- address of descriptor to map
+ * @size:			- size of descriptor to map
+ * @dma:			- DMA address return pointer
+ * @dma_sz:			- adjusted return pointer
  *
  * Returns 0 on success, errno otherwise.
  */
@@ -945,9 +946,9 @@ EXPORT_SYMBOL_GPL(knav_pool_desc_map);
 
 /**
  * knav_pool_desc_unmap()	- Unmap descriptor after DMA transfer
- * @pool			- pool handle
- * @dma				- DMA address of descriptor to unmap
- * @dma_sz			- size of descriptor to unmap
+ * @ph:				- pool handle
+ * @dma:			- DMA address of descriptor to unmap
+ * @dma_sz:			- size of descriptor to unmap
  *
  * Returns descriptor address on success, Use IS_ERR_OR_NULL() to identify
  * error values on return.
@@ -968,7 +969,7 @@ EXPORT_SYMBOL_GPL(knav_pool_desc_unmap);
 
 /**
  * knav_pool_count()	- Get the number of descriptors in pool.
- * @pool		- pool handle
+ * @ph:			- pool handle
  * Returns number of elements in the pool.
  */
 int knav_pool_count(void *ph)
-- 
cgit v1.2.3


From ed93a9e2a1a8448597b4ed4f28b5b7048d4e09e8 Mon Sep 17 00:00:00 2001
From: Lee Jones <lee.jones@linaro.org>
Date: Sat, 21 Nov 2020 19:22:00 -0800
Subject: soc: ti: knav_dma: Fix a kernel function doc formatting issue

Fixes the following W=1 kernel build warning(s):

 drivers/soc/ti/knav_dma.c:507: warning: Function parameter or member 'channel' not described in 'knav_dma_close_channel'

Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/knav_dma.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/soc/ti/knav_dma.c b/drivers/soc/ti/knav_dma.c
index 8c863ecb1c60..b2d63d8854d6 100644
--- a/drivers/soc/ti/knav_dma.c
+++ b/drivers/soc/ti/knav_dma.c
@@ -500,7 +500,7 @@ EXPORT_SYMBOL_GPL(knav_dma_open_channel);
 /**
  * knav_dma_close_channel()	- Destroy a dma channel
  *
- * channel:	dma channel handle
+ * @channel:	dma channel handle
  *
  */
 void knav_dma_close_channel(void *channel)
-- 
cgit v1.2.3


From edac869ed010814d56f766745c64476d5a96bbdd Mon Sep 17 00:00:00 2001
From: Lee Jones <lee.jones@linaro.org>
Date: Sat, 21 Nov 2020 19:22:01 -0800
Subject: soc: ti: pm33xx: Remove set but unused variable 'ret'
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Fixes the following W=1 kernel build warning(s):

 drivers/soc/ti/pm33xx.c: In function ‘am33xx_do_sram_idle’:
 drivers/soc/ti/pm33xx.c:138:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]

Cc: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/pm33xx.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/soc/ti/pm33xx.c b/drivers/soc/ti/pm33xx.c
index d2f5e7001a93..9c0670ab6be6 100644
--- a/drivers/soc/ti/pm33xx.c
+++ b/drivers/soc/ti/pm33xx.c
@@ -135,13 +135,11 @@ static int am33xx_push_sram_idle(void)
 
 static int am33xx_do_sram_idle(u32 wfi_flags)
 {
-	int ret = 0;
-
 	if (!m3_ipc || !pm_ops)
 		return 0;
 
 	if (wfi_flags & WFI_FLAG_WAKE_M3)
-		ret = m3_ipc->ops->prepare_low_power(m3_ipc, WKUP_M3_IDLE);
+		m3_ipc->ops->prepare_low_power(m3_ipc, WKUP_M3_IDLE);
 
 	return pm_ops->cpu_suspend(am33xx_do_wfi_sram, wfi_flags);
 }
-- 
cgit v1.2.3


From 7be1c9c1c00c39ac04e182f3de613c6f30da3d9c Mon Sep 17 00:00:00 2001
From: Lee Jones <lee.jones@linaro.org>
Date: Sat, 21 Nov 2020 19:22:01 -0800
Subject: soc: ti: wkup_m3_ipc: Document 'm3_ipc' parameter throughout

Fixes the following W=1 kernel build warning(s):

 drivers/soc/ti/wkup_m3_ipc.c:227: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_mem_type'
 drivers/soc/ti/wkup_m3_ipc.c:236: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_resume_address'
 drivers/soc/ti/wkup_m3_ipc.c:248: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_request_pm_status'
 drivers/soc/ti/wkup_m3_ipc.c:268: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_prepare_low_power'
 drivers/soc/ti/wkup_m3_ipc.c:322: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_finish_low_power'
 drivers/soc/ti/wkup_m3_ipc.c:369: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_rtc_only'
 drivers/soc/ti/wkup_m3_ipc.c:369: warning: Excess function parameter 'wkup_m3_wakeup' description in 'wkup_m3_set_rtc_only'

Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/wkup_m3_ipc.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/ti/wkup_m3_ipc.c b/drivers/soc/ti/wkup_m3_ipc.c
index e9ece45d7a33..c3e2161df732 100644
--- a/drivers/soc/ti/wkup_m3_ipc.c
+++ b/drivers/soc/ti/wkup_m3_ipc.c
@@ -218,6 +218,7 @@ static int wkup_m3_is_available(struct wkup_m3_ipc *m3_ipc)
 /* Public functions */
 /**
  * wkup_m3_set_mem_type - Pass wkup_m3 which type of memory is in use
+ * @m3_ipc: Pointer to wkup_m3_ipc context
  * @mem_type: memory type value read directly from emif
  *
  * wkup_m3 must know what memory type is in use to properly suspend
@@ -230,6 +231,7 @@ static void wkup_m3_set_mem_type(struct wkup_m3_ipc *m3_ipc, int mem_type)
 
 /**
  * wkup_m3_set_resume_address - Pass wkup_m3 resume address
+ * @m3_ipc: Pointer to wkup_m3_ipc context
  * @addr: Physical address from which resume code should execute
  */
 static void wkup_m3_set_resume_address(struct wkup_m3_ipc *m3_ipc, void *addr)
@@ -239,6 +241,7 @@ static void wkup_m3_set_resume_address(struct wkup_m3_ipc *m3_ipc, void *addr)
 
 /**
  * wkup_m3_request_pm_status - Retrieve wkup_m3 status code after suspend
+ * @m3_ipc: Pointer to wkup_m3_ipc context
  *
  * Returns code representing the status of a low power mode transition.
  *	0 - Successful transition
@@ -260,6 +263,7 @@ static int wkup_m3_request_pm_status(struct wkup_m3_ipc *m3_ipc)
 /**
  * wkup_m3_prepare_low_power - Request preparation for transition to
  *			       low power state
+ * @m3_ipc: Pointer to wkup_m3_ipc context
  * @state: A kernel suspend state to enter, either MEM or STANDBY
  *
  * Returns 0 if preparation was successful, otherwise returns error code
@@ -315,6 +319,7 @@ static int wkup_m3_prepare_low_power(struct wkup_m3_ipc *m3_ipc, int state)
 
 /**
  * wkup_m3_finish_low_power - Return m3 to reset state
+ * @m3_ipc: Pointer to wkup_m3_ipc context
  *
  * Returns 0 if reset was successful, otherwise returns error code
  */
@@ -362,8 +367,7 @@ static const char *wkup_m3_request_wake_src(struct wkup_m3_ipc *m3_ipc)
 
 /**
  * wkup_m3_set_rtc_only - Set the rtc_only flag
- * @wkup_m3_wakeup: struct wkup_m3_wakeup_src * gets assigned the
- *                  wakeup src value
+ * @m3_ipc: Pointer to wkup_m3_ipc context
  */
 static void wkup_m3_set_rtc_only(struct wkup_m3_ipc *m3_ipc)
 {
-- 
cgit v1.2.3


From 50883affe17e11dab530c97b407652193e60471c Mon Sep 17 00:00:00 2001
From: Lee Jones <lee.jones@linaro.org>
Date: Sat, 21 Nov 2020 19:22:01 -0800
Subject: soc: ti: k3-ringacc: Provide documentation for 'k3_ring's 'state'

Fixes the following W=1 kernel build warning(s):

 drivers/soc/ti/k3-ringacc.c:163: warning: Function parameter or member 'state' not described in 'k3_ring'

Cc: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/k3-ringacc.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/soc/ti/k3-ringacc.c b/drivers/soc/ti/k3-ringacc.c
index 7fdb688452f7..119164abcb41 100644
--- a/drivers/soc/ti/k3-ringacc.c
+++ b/drivers/soc/ti/k3-ringacc.c
@@ -137,6 +137,7 @@ struct k3_ring_state {
  * @elm_size: Size of the ring element
  * @mode: Ring mode
  * @flags: flags
+ * @state: Ring state
  * @ring_id: Ring Id
  * @parent: Pointer on struct @k3_ringacc
  * @use_count: Use count for shared rings
-- 
cgit v1.2.3


From e83b2358ab7ef0d39563b4e66233b356f99b7e77 Mon Sep 17 00:00:00 2001
From: Nishanth Menon <nm@ti.com>
Date: Sat, 21 Nov 2020 19:22:01 -0800
Subject: soc: ti: Kconfig: Drop ARM64 SoC specific configs

With the integration of chip-id detection scheme in kernel[1], there
is no specific need to maintain multitudes of SoC specific config
options, discussed as per [2], we have deprecated the usage in other
places for v5.10-rc1. Drop the configuration for the follow on kernel.

[1] drivers/soc/ti/k3-socinfo.c commit 907a2b7e2fc7 ("soc: ti: add k3 platforms chipid module driver")

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/Kconfig | 18 ------------------
 1 file changed, 18 deletions(-)

diff --git a/drivers/soc/ti/Kconfig b/drivers/soc/ti/Kconfig
index f5b82ffa637b..7e2fb1c16af1 100644
--- a/drivers/soc/ti/Kconfig
+++ b/drivers/soc/ti/Kconfig
@@ -1,22 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
-# 64-bit ARM SoCs from TI
-if ARM64
-
-if ARCH_K3
-
-config ARCH_K3_AM6_SOC
-	bool "K3 AM6 SoC"
-	help
-	  Enable support for TI's AM6 SoC Family support
-
-config ARCH_K3_J721E_SOC
-	bool "K3 J721E SoC"
-	help
-	  Enable support for TI's J721E SoC Family support
-
-endif
-
-endif
 
 #
 # TI SOC drivers
-- 
cgit v1.2.3


From 8465c7d1001a86e87f03124dc4a35760e731af62 Mon Sep 17 00:00:00 2001
From: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Date: Sat, 21 Nov 2020 19:22:25 -0800
Subject: soc: ti: pruss: Remove wrong check against *get_match_data return
 value

Since the of_device_get_match_data() doesn't return error code, remove
wrong IS_ERR test. Proper check against NULL pointer is already done
later before usage: if (data && data->...).

Additionally, proceeding with empty device data is valid (e.g. in case
of "ti,am3356-pruss").

Reported-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/pruss.c | 6 ------
 1 file changed, 6 deletions(-)

diff --git a/drivers/soc/ti/pruss.c b/drivers/soc/ti/pruss.c
index cc0b4ad7a3d3..5d6e7132a5c4 100644
--- a/drivers/soc/ti/pruss.c
+++ b/drivers/soc/ti/pruss.c
@@ -126,8 +126,6 @@ static int pruss_clk_init(struct pruss *pruss, struct device_node *cfg_node)
 	int ret = 0;
 
 	data = of_device_get_match_data(dev);
-	if (IS_ERR(data))
-		return -ENODEV;
 
 	clks_np = of_get_child_by_name(cfg_node, "clocks");
 	if (!clks_np) {
@@ -175,10 +173,6 @@ static int pruss_probe(struct platform_device *pdev)
 	const char *mem_names[PRUSS_MEM_MAX] = { "dram0", "dram1", "shrdram2" };
 
 	data = of_device_get_match_data(&pdev->dev);
-	if (IS_ERR(data)) {
-		dev_err(dev, "missing private data\n");
-		return -ENODEV;
-	}
 
 	ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
 	if (ret) {
-- 
cgit v1.2.3


From b4fa73358c306d747a2200aec6f7acb97e5750e6 Mon Sep 17 00:00:00 2001
From: Zhang Qilong <zhangqilong3@huawei.com>
Date: Sat, 21 Nov 2020 19:22:37 -0800
Subject: soc: ti: Fix reference imbalance in knav_dma_probe

The patch fix two reference leak.

  1) pm_runtime_get_sync will increment pm usage counter even it
     failed. Forgetting to call put operation will result in
     reference leak.

  2) The pm_runtime_enable will increase power disable depth. Thus
     a pairing decrement is needed on the error handling path to
     keep it balanced.

We fix it by: 1) adding call pm_runtime_put_noidle or
pm_runtime_put_sync in error handling. 2) adding pm_runtime_disable
in error handling, to keep usage counter and disable depth balanced.

Fixes: 88139ed030583 ("soc: ti: add Keystone Navigator DMA support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/knav_dma.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/ti/knav_dma.c b/drivers/soc/ti/knav_dma.c
index b2d63d8854d6..7b5cb5d48f7d 100644
--- a/drivers/soc/ti/knav_dma.c
+++ b/drivers/soc/ti/knav_dma.c
@@ -749,8 +749,9 @@ static int knav_dma_probe(struct platform_device *pdev)
 	pm_runtime_enable(kdev->dev);
 	ret = pm_runtime_get_sync(kdev->dev);
 	if (ret < 0) {
+		pm_runtime_put_noidle(kdev->dev);
 		dev_err(kdev->dev, "unable to enable pktdma, err %d\n", ret);
-		return ret;
+		goto err_pm_disable;
 	}
 
 	/* Initialise all packet dmas */
@@ -764,7 +765,8 @@ static int knav_dma_probe(struct platform_device *pdev)
 
 	if (list_empty(&kdev->list)) {
 		dev_err(dev, "no valid dma instance\n");
-		return -ENODEV;
+		ret = -ENODEV;
+		goto err_put_sync;
 	}
 
 	debugfs_create_file("knav_dma", S_IFREG | S_IRUGO, NULL, NULL,
@@ -772,6 +774,13 @@ static int knav_dma_probe(struct platform_device *pdev)
 
 	device_ready = true;
 	return ret;
+
+err_put_sync:
+	pm_runtime_put_sync(kdev->dev);
+err_pm_disable:
+	pm_runtime_disable(kdev->dev);
+
+	return ret;
 }
 
 static int knav_dma_remove(struct platform_device *pdev)
-- 
cgit v1.2.3


From 4cba398f37f868f515ff12868418dc28574853a1 Mon Sep 17 00:00:00 2001
From: Zhihao Cheng <chengzhihao1@huawei.com>
Date: Sat, 21 Nov 2020 19:22:38 -0800
Subject: drivers: soc: ti: knav_qmss_queue: Fix error return code in
 knav_queue_probe

Fix to return the error code from of_get_child_by_name() instaed of 0
in knav_queue_probe().

Fixes: 41f93af900a20d1a0a ("soc: ti: add Keystone Navigator QMSS driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
---
 drivers/soc/ti/knav_qmss_queue.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/soc/ti/knav_qmss_queue.c b/drivers/soc/ti/knav_qmss_queue.c
index 490423ecdcdd..2e521f1eda96 100644
--- a/drivers/soc/ti/knav_qmss_queue.c
+++ b/drivers/soc/ti/knav_qmss_queue.c
@@ -1852,9 +1852,10 @@ static int knav_queue_probe(struct platform_device *pdev)
 	if (ret)
 		goto err;
 
-	regions =  of_get_child_by_name(node, "descriptor-regions");
+	regions = of_get_child_by_name(node, "descriptor-regions");
 	if (!regions) {
 		dev_err(dev, "descriptor-regions not specified\n");
+		ret = -ENODEV;
 		goto err;
 	}
 	ret = knav_queue_setup_regions(kdev, regions);
-- 
cgit v1.2.3