From 66e7da4e34610e84bdb1bf726031d6c4c88cbbf9 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Mon, 9 Jul 2007 11:46:22 -0700 Subject: pata_hpt3x3: major reworking and testing The HPT343/345 (aka 363) is a bit of a warped device. For many setups you need to access the other registers via BAR4 offsets. PIO is now rock solid, DMA isn't. Unfortunately the drivers/ide hpt34x driver is completely broken so doesn't help further debug. Signed-off-by: Alan Cox Cc: Bartlomiej Zolnierkiewicz Signed-off-by: Andrew Morton Signed-off-by: Jeff Garzik --- drivers/ata/Kconfig | 10 +++++- drivers/ata/pata_hpt3x3.c | 90 +++++++++++++++++++++++++++++++++++++++-------- 2 files changed, 85 insertions(+), 15 deletions(-) diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index 4ad8675f5a16..d8046a113c37 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -309,7 +309,7 @@ config PATA_HPT3X2N If unsure, say N. config PATA_HPT3X3 - tristate "HPT 343/363 PATA support (Experimental)" + tristate "HPT 343/363 PATA support" depends on PCI help This option enables support for the HPT 343/363 @@ -317,6 +317,14 @@ config PATA_HPT3X3 If unsure, say N. +config PATA_HPT3X3_DMA + bool "HPT 343/363 DMA support (Experimental)" + depends on PATA_HPT3X3 + help + This option enables DMA support for the HPT343/363 + controllers. Enable with care as there are still some + problems with DMA on this chipset. + config PATA_ISAPNP tristate "ISA Plug and Play PATA support (Experimental)" depends on EXPERIMENTAL && ISAPNP diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c index d928c9105034..a66e2c3a221b 100644 --- a/drivers/ata/pata_hpt3x3.c +++ b/drivers/ata/pata_hpt3x3.c @@ -23,7 +23,7 @@ #include #define DRV_NAME "pata_hpt3x3" -#define DRV_VERSION "0.4.3" +#define DRV_VERSION "0.5.3" /** * hpt3x3_set_piomode - PIO setup @@ -59,6 +59,9 @@ static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev) * * Set up the channel for MWDMA or UDMA modes. Much the same as with * PIO, load the mode number and then set MWDMA or UDMA flag. + * + * 0x44 : bit 0-2 master mode, 3-5 slave mode, etc + * 0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc */ static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev) @@ -76,14 +79,26 @@ static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev) r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ if (adev->dma_mode >= XFER_UDMA_0) - r2 |= 0x01 << dn; /* Ultra mode */ + r2 |= (0x10 << dn); /* Ultra mode */ else - r2 |= 0x10 << dn; /* MWDMA */ + r2 |= (0x01 << dn); /* MWDMA */ pci_write_config_dword(pdev, 0x44, r1); pci_write_config_dword(pdev, 0x48, r2); } +/** + * hpt3x3_atapi_dma - ATAPI DMA check + * @qc: Queued command + * + * Just say no - we don't do ATAPI DMA + */ + +static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc) +{ + return 1; +} + static struct scsi_host_template hpt3x3_sht = { .module = THIS_MODULE, .name = DRV_NAME, @@ -105,7 +120,6 @@ static struct scsi_host_template hpt3x3_sht = { static struct ata_port_operations hpt3x3_port_ops = { .port_disable = ata_port_disable, .set_piomode = hpt3x3_set_piomode, - .set_dmamode = hpt3x3_set_dmamode, .mode_filter = ata_pci_default_filter, .tf_load = ata_tf_load, @@ -124,6 +138,7 @@ static struct ata_port_operations hpt3x3_port_ops = { .bmdma_start = ata_bmdma_start, .bmdma_stop = ata_bmdma_stop, .bmdma_status = ata_bmdma_status, + .check_atapi_dma= hpt3x3_atapi_dma, .qc_prep = ata_qc_prep, .qc_issue = ata_qc_issue_prot, @@ -158,32 +173,79 @@ static void hpt3x3_init_chipset(struct pci_dev *dev) pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20); } - /** * hpt3x3_init_one - Initialise an HPT343/363 - * @dev: PCI device + * @pdev: PCI device * @id: Entry in match table * - * Perform basic initialisation. The chip has a quirk that it won't - * function unless it is at XX00. The old ATA driver touched this up - * but we leave it for pci quirks to do properly. + * Perform basic initialisation. We set the device up so we access all + * ports via BAR4. This is neccessary to work around errata. */ -static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id) +static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id) { + static int printed_version; static const struct ata_port_info info = { .sht = &hpt3x3_sht, .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = 0x1f, +#if defined(CONFIG_PATA_HPT3X3_DMA) + /* Further debug needed */ .mwdma_mask = 0x07, .udma_mask = 0x07, +#endif .port_ops = &hpt3x3_port_ops }; + /* Register offsets of taskfiles in BAR4 area */ + static const u8 offset_cmd[2] = { 0x20, 0x28 }; + static const u8 offset_ctl[2] = { 0x36, 0x3E }; const struct ata_port_info *ppi[] = { &info, NULL }; - - hpt3x3_init_chipset(dev); - /* Now kick off ATA set up */ - return ata_pci_init_one(dev, ppi); + struct ata_host *host; + int i, rc; + void __iomem *base; + + hpt3x3_init_chipset(pdev); + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2); + if (!host) + return -ENOMEM; + /* acquire resources and fill host */ + rc = pcim_enable_device(pdev); + if (rc) + return rc; + + /* Everything is relative to BAR4 if we set up this way */ + rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME); + if (rc == -EBUSY) + pcim_pin_device(pdev); + if (rc) + return rc; + host->iomap = pcim_iomap_table(pdev); + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + return rc; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + return rc; + + base = host->iomap[4]; /* Bus mastering base */ + + for (i = 0; i < host->n_ports; i++) { + struct ata_ioports *ioaddr = &host->ports[i]->ioaddr; + + ioaddr->cmd_addr = base + offset_cmd[i]; + ioaddr->altstatus_addr = + ioaddr->ctl_addr = base + offset_ctl[i]; + ioaddr->scr_addr = NULL; + ata_std_ports(ioaddr); + ioaddr->bmdma_addr = base + 8 * i; + } + pci_set_master(pdev); + return ata_host_activate(host, pdev->irq, ata_interrupt, IRQF_SHARED, + &hpt3x3_sht); } #ifdef CONFIG_PM -- cgit v1.2.3