| Age | Commit message (Collapse) | Author |
|---|
|
Fix up multiple instances of "intervall" to correct
"interval" (all save one Italian instance).
Signed-off-by: Nick Black <dankamongmen@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The token before "-" should be the program name, no spaces allowed.
See man(7) and lexgrog(1).
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
cpupower idle-set -D <latency>
currently only disables all C-states that have a higher latency than the
specified <latency>. But if deep sleep states were already disabled and
have a lower latency, they should get enabled again.
For example:
This call:
cpupower idle-set -D 30
disables all C-states with a higher or equal latency than 30.
If one then calls:
cpupower idle-set -D 100
C-states with a latency between 30-99 will get enabled again with this patch
now. It is ensured that only C-states with a latency of 100 and higher are
disabled.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
These kernel interfaces got removed by:
commit 8e7fbcbc22c12414bcc9dfdd683637f58fb32759
Author: Peter Zijlstra <peterz@infradead.org>
Date: Mon Jan 9 11:28:35 2012 +0100
sched: Remove stale power aware scheduling remnants and dysfunctional knobs
No need to further keep them as userspace configurations.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The command "cpupower frequency-info" can be used when using cpupower to
monitor and test processor behaviour to determine if the processor is
behaving as expected. This data can be compared to the output of
/proc/cpuinfo or the output of
/sys/devices/system/cpu/cpuX/cpufreq/scaling_available_frequencies
to determine if the cpu is in an expected state.
When doing this I noticed comparison test failures due to the way the
data is displayed in cpupower. For example,
[root@intel-s3e37-02 cpupower]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies
2262000 2261000 2128000 1995000 1862000 1729000 1596000 1463000 1330000
1197000 1064000
compared to
[root@intel-s3e37-02 cpupower]# cpupower frequency-info
analyzing CPU 0:
driver: acpi-cpufreq
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: 10.0 us.
hardware limits: 1.06 GHz - 2.26 GHz
available frequency steps: 2.26 GHz, 2.26 GHz, 2.13 GHz, 2.00 GHz, 1.86 GHz, 1.73 GHz, 1.60 GHz, 1.46 GHz, 1.33 GHz, 1.20 GHz, 1.06 GHz
available cpufreq governors: conservative, userspace, powersave, ondemand, performance
current policy: frequency should be within 1.06 GHz and 2.26 GHz.
The governor "performance" may decide which speed to use
within this range.
current CPU frequency is 2.26 GHz (asserted by call to hardware).
boost state support:
Supported: yes
Active: yes
shows very different values for the available frequency steps. The cpupower
output rounds off values at 2 decimal points and this causes problems with
test scripts. For example, with the data above,
1.064 is 1.06
1.197 is 1.20
1.596 is 1.60
1.995 is 2.00
2.128 is 2.13
and most confusingly,
2.261 is 2.26
2.262 is 2.26
Truncating these values serves no real purpose other than making the output
pretty. Since the default has been to round off these values I am adding
a -n/--no-rounding option to the cpupower utility that will display the
data without rounding off the still significant digits.
After patch,
analyzing CPU 0:
driver: acpi-cpufreq
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: 10.000 us.
hardware limits: 1.064000 GHz - 2.262000 GHz
available frequency steps: 2.262000 GHz, 2.261000 GHz, 2.128000 GHz, 1.995000 GHz, 1.862000 GHz, 1.729000 GHz, 1.596000 GHz, 1.463000 GHz, 1.330000 GHz, 1.197000 GHz, 1.064000 GHz
available cpufreq governors: conservative, userspace, powersave, ondemand, performance
current policy: frequency should be within 1.064000 GHz and 2.262000 GHz.
The governor "performance" may decide which speed to use
within this range.
current CPU frequency is 2.262000 GHz (asserted by call to hardware).
boost state support:
Supported: yes
Active: yes
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpupower idle-set subcommand was introduce recently.
This patch provides the missing manpage.
If cpupower is properly installed it will show up automatically
(similar to git), when invoking:
cpupower help idle-set
or
cpupower idle-set --help
Some parts have been taken over and adjusted from
git commit 62d6ae880e3e76098
documentation submitted by Carsten Emde.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Example:
cpupower idle-set -d 3
will disable C-state 3 on all processors (set commands are active on
all CPUs by default), same as:
cpupower -c all idle-set -d 3
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If an MSR based monitor is run in parallel this is not needed. This is the
default case on all/most Intel machines.
But when only sysfs info is read via cpupower monitor -m Idle_Stats (typically
the case for non root users) or when other monitors are PCI based (AMD),
Idle_Stats, read from sysfs can be totally bogus:
cpupower monitor -m Idle_Stats
PKG |CORE|CPU | POLL | C1-N | C3-N | C6-N
0| 0| 0| 0.00| 0.00| 0.24| 99.81
0| 0| 32| 0.00| 0.00| 0.00| 100.7
...
0| 17| 20| 0.00| 0.00| 0.00| 173.1
0| 17| 52| 0.00| 0.00| 0.07| 173.0
0| 18| 68| 0.00| 0.00| 0.00| 0.00
0| 18| 76| 0.00| 0.00| 0.00| 0.00
...
With the -c option all cores are woken up and the kernel
did update cpuidle statistics before reading out sysfs.
This causes some overhead. Therefore avoid if possible, use
if needed:
cpupower monitor -c -m Idle_Stats
PKG |CORE|CPU | POLL | C1-N | C3-N | C6-N
0| 0| 0| 0.00| 0.00| 0.00| 100.2
0| 0| 32| 0.00| 0.00| 0.00| 100.2
...
0| 8| 8| 0.00| 0.00| 0.00| 99.82
0| 8| 40| 0.00| 0.00| 0.00| 99.81
0| 9| 24| 0.00| 0.00| 0.00| 100.3
0| 9| 56| 0.00| 0.00| 0.00| 100.2
0| 16| 4| 0.00| 0.00| 0.00| 99.75
0| 16| 36| 0.00| 0.00| 0.00| 99.38
...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It's been broken forever (i.e. it's not scheduling in a power
aware fashion), as reported by Suresh and others sending
patches, and nobody cares enough to fix it properly ...
so remove it to make space free for something better.
There's various problems with the code as it stands today, first
and foremost the user interface which is bound to topology
levels and has multiple values per level. This results in a
state explosion which the administrator or distro needs to
master and almost nobody does.
Furthermore large configuration state spaces aren't good, it
means the thing doesn't just work right because it's either
under so many impossibe to meet constraints, or even if
there's an achievable state workloads have to be aware of
it precisely and can never meet it for dynamic workloads.
So pushing this kind of decision to user-space was a bad idea
even with a single knob - it's exponentially worse with knobs
on every node of the topology.
There is a proposal to replace the user interface with a single
3 state knob:
sched_balance_policy := { performance, power, auto }
where 'auto' would be the preferred default which looks at things
like Battery/AC mode and possible cpufreq state or whatever the hw
exposes to show us power use expectations - but there's been no
progress on it in the past many months.
Aside from that, the actual implementation of the various knobs
is known to be broken. There have been sporadic attempts at
fixing things but these always stop short of reaching a mergable
state.
Therefore this wholesale removal with the hopes of spurring
people who care to come forward once again and work on a
coherent replacement.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1326104915.2442.53.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
cpupower-frequency-* manpages slightly differed from the others.
- Use uppercase letters in the title
- Show cpupower Manual in the header
- Remove Mattia from left down corner of the manpage, he is already
listed as author
- Remove --help, prints this message -> not needed
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
The last missing manpage for cpupower tools.
More info about other architecture's sleep state specialities would be great.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
The name of the monitor is updated at runtime to the name of the
CPU type.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Instead of printing something non-formatted to stdout, call
man(1) to show the man page for the proper subcommand.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
CPU power consumption vs performance tuning is no longer
limited to CPU frequency switching anymore: deep sleep states,
traditional dynamic frequency scaling and hidden turbo/boost
frequencies are tied close together and depend on each other.
The first two exist on different architectures like PPC, Itanium and
ARM, the latter (so far) only on X86. On X86 the APU (CPU+GPU) will
only run most efficiently if CPU and GPU has proper power management
in place.
Users and Developers want to have *one* tool to get an overview what
their system supports and to monitor and debug CPU power management
in detail. The tool should compile and work on as many architectures
as possible.
Once this tool stabilizes a bit, it is intended to replace the
Intel-specific tools in tools/power/x86
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
