| Age | Commit message (Collapse) | Author |
|---|
|
'asoc/topic/max98504' and 'asoc/topic/nau8825' into asoc-next
|
|
'asoc/topic/extcon' and 'asoc/topic/fsl' into asoc-next
|
|
'asoc/topic/cs42l73' and 'asoc/topic/cs42xx8' into asoc-next
|
|
'asoc/topic/cs35l34' into asoc-next
|
|
'asoc/topic/atmel', 'asoc/topic/bcm' and 'asoc/topic/bitfield' into asoc-next
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
into asoc-linus
|
|
|
|
buf was allocated by kzalloc() so it should be passed to kfree()
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When num_kcontrols is zero, widget->dobj.widget.kcontrol_type
gets set to an uninitialized local variable:
sound/soc/soc-topology.c: In function 'soc_tplg_dapm_widget_create':
sound/soc/soc-topology.c:1566:36: error: 'kcontrol_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I could not figure out which of the valid types would be appropriate
here, so this sets it to '0', which is invalid but at least well-defined
here. There is probably a better way to address the issue.
Fixes: eea3dd4f1247 ("ASoC: topology: Only free TLV for volume mixers of a widget")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
The Logitech QuickCam Communicate Deluxe/S7500 microphone fails with the
following warning.
[ 6.778995] usb 2-1.2.2.2: Warning! Unlikely big volume range (=3072),
cval->res is probably wrong.
[ 6.778996] usb 2-1.2.2.2: [5] FU [Mic Capture Volume] ch = 1, val =
4608/7680/1
Adding it to the list of devices in volume_control_quirks makes it work
properly, fixing related typo.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Axe-Fx II implicit feedback end point and the data sync endpoint
are in different interface descriptors. Add quirk to ensure a sync
endpoint is properly configured.
Signed-off-by: Alberto Aguirre <albaguirre@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The macro ZX_SPDIF_CLK_RAT should be 2 instead of 4. With this
fix, we can get correct audio output on HDMI through SPDIF interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ZTE ZX SPDIF and I2S drivers can work on not only ZX296702 but also
other ZTE ZX family SoCs like ZX296718, which is an arm64 platform.
Let's make a few renaming and tweak the Kconfig a bit to get the drivers
available for other ZTE ZX platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current rsnd driver setups BRGCKR/BRRA/BRRB when .probe timing.
But it breaks sound after Suspend/Resume. These should be setups
every start timing.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current rsnd driver enables ADG clock when .probe timing,
but it breaks sound after Suspend/Resume. These should be setups
every suspend/resume timing too.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ssi->usrcnt will be updated on snd_soc_dai_ops::trigger,
but snd_pcm_ops::hw_params will be called *before* it.
Thus, ssi->usrcnt is still 0 when 1st call.
rsnd_ssi_hw_params() needs to check its called count, this means
trigger should be if (ssi->usrcnt) instead of if (ssi->usrcnt > 1).
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We accidentally deleted a newline so now the "nreallocated++;" statement
is hanging out way off to the right of the screen.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We accidentally introduced a dereference before the NULL check in
xmit_descs() as part of silencing a GCC warning.
Fixes: 16f46050e709 ("dbri: Fix compiler warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates FE channel constraints & BE fixup to support
quad channel DMIC capture.
DMIC pin's BE fixup is configured based on channel input, i.e.
either stereo or quad.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This bit will enable 4th order SINC filter.
=1, filter will enable; but it consumes higher power.
=0, the sinc filter is disable, and it should always keep 0 value to
get high THD.
Therefor, disable the filter when codec initiation for better
performance when recording.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
since commit 57e6dae1087b ("ALSA: usb-audio: do not trust too-big
wMaxPacketSize values"), the expected packetsize is always limited
to nominal + 25%. It was discovered, that some devices (Android audio
accessory) have a much higher jitter in used packetsizes than 25%
which would result in BABBLE condition and dropping of packets.
A better solution is so assume the jitter to be the nominal packetsize:
-one nearly empty packet followed by a almost 150% sized one.
V2: changed to assume max frequency is +50 of nominal packetsize.
Signed-off-by: Andreas Pape <apape@de.adit-jv.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some of userland applications call 'snd_pcm_hw_params()' and
'snd_pcm_hw_prepare()' sequentially, which means 'snd_pcm_hw_prepare()'
is called twice and the second 'snd_pcm_hw_prepare()' is called in
'SNDRV_PCM_STATE_PREPARED' state.
Some devices are not able to manage this and they will stop playback
if the sample rate will be configured several times over USB protocol.
V2: updated Changelog
Signed-off-by: Daniel Girnus <dgirnus@de.adit-jv.com>
Signed-off-by: Jens Lorenz <jlorenz@de.adit-jv.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The logic of "value = ~CS35L34_MCLK_DIV & CS35L34_MCLK_RATE_XXXXXX;" is
unnecessary complex. By setting CS35L34_MCLK_DIV | CS35L34_MCLK_RATE_MASK
as the mask for regmap_update_bits() call, what the code does is exactly
the same as setting value = CS35L34_MCLK_RATE_XXXXXX.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
HP Z1 Gen3 AiO with Conexant codec doesn't give an unsolicited event
to the headset mic pin upon the jack plugging, it reports only to the
headphone pin. It results in the missing mic switching. Let's fix up
by simply gating the jack event.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit [64047d7f4912 ALSA: hda - ignore the assoc and seq when comparing
pin configurations] intented to ignore both seq and assoc at pin
comparing, but it only ignored seq. So that commit may still fail to
match pins on some machines.
Change the bitmask to also ignore assoc.
v2: Use macro to do bit masking.
Thanks to Hui Wang for the analysis.
Fixes: 64047d7f4912 ("ALSA: hda - ignore the assoc and seq when comparing...")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
After the boot of the SST FW the firmware version is send back
to the driver. This patch is saving the FW version inside the
driver.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch is adding a sysfs entry in order to be able to get
access to SST FW version.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the CS42L56_AIN*_REF_MASK
masks, which equal 0x10, 0x20, 0x40 and 0x80. Fix the driver to make it
consistent with the API. Please note that this change is untested,
as I do not have this piece of hardware. Testers are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch will check the type of embedded controls for a widget, and
only free the TLV of volume mixers. Bytes controls don't have TLV.
Just free the private value which is used as struct soc_mixer_control
for volume mixers or soc_bytes_ext for bytes controls. No need to cast
to these types before freeing it.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch can create multiple enumerated mixer controls for a widget.
Previously topology kernel driver assumes a widget can have only one
emumerated mixer control. We need to remove this restriction for Broxton.
Its firmware modules (widgets) may need multiple enum controls based on
the channel and MIC combination.
No ABI change is needed. The ABI allows a widget to embed multiple
controls.
Reported-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
simple_card_utils was created as simple_card_core in 1st prototype,
and current code still have it. Let's tidyup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SSIU was controlled by SSI before, but
commit c7f69ab53("ASoC: rsnd: use mod base common method on SSIU")
separated it into ssiu.c
But, it didn't care about rsnd_get_dalign() for judging SSI_BUSIF_DALIGN
register value which changes the stream data order.
This function will be called from cmd/src/ssiu now, but current code
still cares ssi, not ssiu.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We've got a kernel crash report showing like:
Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = a1d7c000
[00000008] *pgd=31c93831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
CPU: 0 PID: 250 Comm: dbus-daemon Not tainted 3.14.51-03479-gf50bdf4 #1
task: a3ae61c0 ti: a08c8000 task.ti: a08c8000
PC is at retire_capture_urb+0x10/0x1f4 [snd_usb_audio]
LR is at snd_complete_urb+0x140/0x1f0 [snd_usb_audio]
pc : [<7f0eb22c>] lr : [<7f0e57fc>] psr: 200e0193
sp : a08c9c98 ip : a08c9ce8 fp : a08c9ce4
r10: 0000000a r9 : 00000102 r8 : 94cb3000
r7 : 94cb3000 r6 : 94d0f000 r5 : 94d0e8e8 r4 : 94d0e000
r3 : 7f0eb21c r2 : 00000000 r1 : 94cb3000 r0 : 00000000
Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 31d7c04a DAC: 00000015
Process dbus-daemon (pid: 250, stack limit = 0xa08c8238)
Stack: (0xa08c9c98 to 0xa08ca000)
...
Backtrace:
[<7f0eb21c>] (retire_capture_urb [snd_usb_audio]) from [<7f0e57fc>] (snd_complete_urb+0x140/0x1f0 [snd_usb_audio])
[<7f0e56bc>] (snd_complete_urb [snd_usb_audio]) from [<80371118>] (__usb_hcd_giveback_urb+0x78/0xf4)
[<803710a0>] (__usb_hcd_giveback_urb) from [<80371514>] (usb_giveback_urb_bh+0x8c/0xc0)
[<80371488>] (usb_giveback_urb_bh) from [<80028e3c>] (tasklet_hi_action+0xc4/0x148)
[<80028d78>] (tasklet_hi_action) from [<80028358>] (__do_softirq+0x190/0x380)
[<800281c8>] (__do_softirq) from [<80028858>] (irq_exit+0x8c/0xfc)
[<800287cc>] (irq_exit) from [<8000ea88>] (handle_IRQ+0x8c/0xc8)
[<8000e9fc>] (handle_IRQ) from [<800085e8>] (gic_handle_irq+0xbc/0xf8)
[<8000852c>] (gic_handle_irq) from [<80509044>] (__irq_svc+0x44/0x78)
[<80508820>] (_raw_spin_unlock_irq) from [<8004b880>] (finish_task_switch+0x5c/0x100)
[<8004b824>] (finish_task_switch) from [<805052f0>] (__schedule+0x48c/0x6d8)
[<80504e64>] (__schedule) from [<805055d4>] (schedule+0x98/0x9c)
[<8050553c>] (schedule) from [<800116c8>] (do_work_pending+0x30/0xd0)
[<80011698>] (do_work_pending) from [<8000e160>] (work_pending+0xc/0x20)
Code: e1a0c00d e92ddff0 e24cb004 e24dd024 (e5902008)
Kernel panic - not syncing: Fatal exception in interrupt
There is a race between retire_capture_urb() and stop_endpoints().
The latter is called at stopping the stream and it sets some endpoint
fields to NULL. But its call is asynchronous, thus the pending
complete callback might get called after these NULL clears, and it
leads the NULL dereference like the above.
The fix is to move the NULL clearance after the synchronization,
i.e. wait_clear_urbs(). This is called at prepare and hw_free
callbacks, so it's assured to be called before the restart of the
stream or the release of the stream.
Also, while we're at it, put the EP_FLAG_RUNNING flag check at the
beginning of snd_complete_urb() to skip the pending complete after the
stream is stopped.
Fixes: b2eb950de2f0 ("ALSA: usb-audio: stop both data and sync...")
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Reported-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Linux 4.9-rc8
Daniel requested this so we could apply some follow on fixes cleanly to -next.
|
|
This patch adds the sound machine driver for the TM2 and TM2E boards.
Speaker and headphone playback, Main Mic capture, Bluetooth, Voice
call and external accessory are supported.
Signed-off-by: Inha Song <ideal.song@samsung.com>
[k.kozlowski: rebased on 4.1]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[s.nawrocki: rebased to 4.7, adjustment to the ASoC core changes,
removed unused ops and direct calls to the max98504 function,
added parsing of "audio-amplifier" and "audio-codec"
properties, added TDM API calls, switched to gpiod API]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel
|
|
In current ALSA SoC, Codec only has suspend/resume feature,
but it should be supported on Component level. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now, Card has component_dev_list, we can replace aux_comp_list
to component_dev_list with new auxiliary flags
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current Card has Codec list (= codec_dev_list), but Codec will be
removed in the future. Because of this reason, this patch adds
new Component list in Card, and replace Codec list.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec on the H3 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the H3 has no HP (headphone) and HBIAS support, and no
MIC3 input. The FIFO related registers are slightly rearranged.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec in the A23 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the A23 does not have LINEOUT, and it does not support
headset jack detection or buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of hard-coded "i2c-10EC5670:00", use the translation helper to
avoid the mismatch between i2c-codec and ACPI strings just like what
we've done for bytcr_rt5640. This gives more robust binding on funky
devices like Dell Wyse 3040.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
