| Age | Commit message (Collapse) | Author |
|---|
|
This patch converts the ad1980 driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-ac97
|
|
Some drivers (most notably the AC'97 drivers) do not have access to their
regmap struct when the component/codec is registered. For those drivers the
automatic regmap setup will not work and needs to be done manually,
typically from the component/CODEC drivers probe callback.
This patch adds a set of helper function to handle deferred regmap
initialization as well as early regmap tear-down.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that the ASoC core no longer needs a handle to the AC'97 device that is
associated with a CODEC we can remove it from the snd_soc_codec struct and
push it into the individual driver state structs like we do for other
communication buses. Doing so creates a clean separation between the AC'97
bus support and the ASoC core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Setting the ac97_control field on a CPU DAI tells the ASoC core that this
DAI in addition to audio data also transports control data to the CODEC.
This causes the core to suspend the DAI after the CODEC and resume it before
the CODEC so communication to the CODEC is still possible. This is not
necessarily something that is specific to AC'97 and can be used by other
buses with the same requirement. This patch renames the flag from
ac97_control to bus_control to make this explicit.
While we are at it also change the type from int to bool.
The following semantich patch was used for automatic conversion of the
drivers:
// <smpl>
@@
identifier drv;
@@
struct snd_soc_dai_driver drv = {
- .ac97_control
+ .bus_control
=
- 1
+ true
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is no longer necessary as there is no code anymore that uses this for
CODEC DAIs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have all the information and dependencies we need to initialize and
register the device available in snd_soc_new_ac97_codec(). So there is no
need to delay the device registration until after the card itself as been
registered.
This makes the code significantly simpler and also makes it possible to use
the AC'97 device in the CODECs probe function. The later will be required to
be able to convert the AC'97 CODEC drivers to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This has no users since commit f0fba2ad1b6b ("ASoC: multi-component - ASoC
Multi-Component Support") which was almost 5 years ago. Given that this runs
after CODEC probe functions have been run it also doesn't seem to be that
useful.
So drop it altogether to make the code simpler.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
soc_{un,}register_ac97_codec() is just a simple wrapper around
soc_ac97_dev_{un,}register(). There is no need to split these up into two
different sets of functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We always pass soc_ac97_ops to snd_soc_new_ac97_codec(). So instead of
allocating a snd_ac97_bus in snd_soc_new_ac97_codec() just use a static one
that gets initialized when snd_soc_set_ac97_ops() is called.
Also drop the device number parameter from snd_soc_new_ac97_codec(). We
currently only support one device per bus and all drivers pass 0 for the
device number. And if we should ever support multiple devices per bus it
wouldn't be up to individual AC'97 device drivers to pick their number, but
rather either the AC'97 adapter driver or the core code will assign them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the AC'97 support is splattered all throughout soc-core.c. Some
parts are #ifdef'd some parts are not. This patch moves the AC'97 support to
its own file, this should make the code a bit more clearer and also makes it
possible to easily not compile it into the kernel when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The memory that a struct device is contained in must not be freed except
from within the device's release callback. The ASoC code currently does not
adhere to this rule for the AC'97 device. This patch fixes it by moving the
freeing of the AC'97 to the release callback and splitting up the
registration and unregistration of the device into separate steps for
getting/putting the reference to the device and adding/removing it to the
device hierarchy.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mpc5200_dma overwrites the private_data field of the CODEC's AC'97
device with the DMA drivers private data, but never actually reads it again.
Given that the private_data field is supposed to be owned by the AC'97
driver, overwriting it may cause undefined behavior. This patch removes the
code that overwrites the field from the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mpc5200_psc_ac97 driver puts a snd_ac97 device on the stack in the
driver probe function, initializes the private data member of the device and
the never uses the device again. It should be safe to remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-ac97
|
|
The wm9712/wm9713 has separate mixers for the left and the right channel,
but the inputs to the mixers are enabled/disabled by the same control.
Currently this is implemented by the driver by registering two virtual
controls for each physical control, one for the left mixer and one for the
right mixer.
Using virtual registers will no longer work when the driver has
been converted to regmap. This patch converts the driver to use controls
with custom put/get callbacks instead which implement the logic making sure
that the physical control is unmuted when either the left or the right
control is unmuted.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-wm971x
|
|
The wm9713 currently implements the virtual control for the Mic B Source MUX
using a virtual register. Replace this by using SOC_ENUM_SINGLE_VIRT().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Resources for the device should be allocated in the device driver probe
callback, rather than in the ASoC CODEC probe callback.
E.g. one advantage is that we can use device managed allocations.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use dev_err()/dev_warn() instead of printk(KERN_ERR/KERN_WARNING. This is
common practice and makes it easy to find out which device generated the
message. While we are at it also align the error messages with the other
AC'97 drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use dev_err() instead of printk(KERN_ERR. This is common practice and makes
it easy to find out which device generated the message. While we are at it
also align the error messages with the other AC'97 drivers.
Also avoid printing two error messages when the reset fails.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use dev_err() instead of printk(KERN_ERR. This is common practice and makes
it easy to find out which device generated the message. While we are at it
also align the error messages with the other AC'97 drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use dev_err()/dev_warn() instead of printk(KERN_ERR/KERN_WARNING. This is
common practice and makes it easy to find out which device generated the
message. While we are at it also align the error messages with the other
AC'97 drivers.
Also remove the info message that is printed when the driver is probed, this
is just noise in bootlog.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The constants defined in the ad1980 header are not used. So remove the file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes after 3.18 merge.
The urgent one is the fix for kernel panics with linked PCM substream
triggered by the recent nonatomic PCM ops support. Other two fixes
(emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
a new Intel HD-audio controller"
* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
ALSA: emu10k1: Fix deadlock in synth voice lookup
ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88
|
|
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
|
|
The introduced include/linux/dma/dw.h is going to contain the private
extensions and structures which are shared for dw_dmac users in the kernel.
Meanwhile include/linux/platform_data/dma-dw.h keeps only platform related data
types and definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch adds the HD Audio Device IDs for the Intel Sunrise Point PCH.
[the item position rearranged by tiwai]
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch"
[ Delayed to after the poweer/reset pull due to Kconfig problems with
recursive Kconfig select/depends-on chains. - Linus ]
* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
i2c: i2c-cros-ec-tunnel: Set retries to 3
mfd: cros_ec: move locking into cros_ec_cmd_xfer
mfd: cros_ec: stop calling ->cmd_xfer() directly
mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
mfd: arizona: Correct mask to allow setting micbias external cap
mfd: Add ACPI support
Revert "mfd: wm5102: Manually apply register patch"
mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
mfd: Inherit coherent_dma_mask from parent device
mfd: Document DT bindings for Qualcomm SPMI PMICs
mfd: Add support for Qualcomm SPMI PMICs
mfd: dt-bindings: pm8xxx: Add new compatible string
mfd: axp209x: Drop the parent supplies field
mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
mfd: syscon: Add Atmel GPBR DT bindings documention
...
|
|
The emu10k1 voice allocator takes voice_lock spinlock. When there is
no empty stream available, it tries to release a voice used by synth,
and calls get_synth_voice. The callback function,
snd_emu10k1_synth_get_voice(), however, also takes the voice_lock,
thus it deadlocks.
The fix is simply removing the voice_lock holds in
snd_emu10k1_synth_get_voice(), as this is always called in the
spinlock context.
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In the unlock loop of snd_pcm_action_group(), the object "s" is used
as the check of nonatomic PCM, but it should be rather "s1", which is
the iterator of the loop. This supposedly causes a kernel panic when
the substreams in operatino are linked.
Fixes: 257f8cce5d40 ('ALSA: pcm: Allow nonatomic trigger operations')
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time it's a relatively calm update batch, but the amount isn't
too small in the end. Here we go over some highlights:
ALSA core:
- One major change is the support of nonatomic PCM operations. This
allows the trigger and other callbacks to call schedule(), which
would be useful for mailbox type communications. Already some
drivers (Digigram ones) have been converted to use together with
threaded irqs as an example.
- Improvement / fixes of DSD PCM format support
HD-audio:
- Large volume of rewrites are found in Realtek codec driver for
converting Dell and HP quirks to generic forms.
- Inverted dmic code cleanup from David.
- Realtek COEF access has been optimized.
- Now HD-audio jack infrastructure allows multiple callbacks, which
fixes / simplifies the jack-dependent power controls on STAC/IDT
and VIA codecs.
- Many additional device-specific fixups as usual
- A few deadcode cleanups, CA0132 code cleanup, etc.
ASoC:
- More componentization work from Lars-Peter, this time mainly
cleaning up the suspend and bias level transition callbacks.
- Real system support for the Intel drivers and a bunch of fixes and
enhancements for the associated CODEC drivers, this is going to
need a lot quirks over time due to the lack of any firmware
description of the boards.
- Jack detect support for simple card from Dylan Reid.
- A bunch of small fixes and enhancements for the Freescale drivers.
- New drivers for Analog Devices SSM4567, Cirrus Logic CS35L32,
Everest Semiconductor ES8328 and Freescale cards using the ASRC in
newer i.MX processors.
- A few simple-card fixes, mostly cleanups but also a fix for
interaction between GPIO 0 and simple-card.
Misc:
- Virtuoso / Oxygen updates by Clemens
- USB-audio: Yamaha MOTIF XF MIDI port name fixes
- Conversion of kernel messages to standard dev_*() in ctxfi driver"
* tag 'sound-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (251 commits)
ASoC: mc13783: Ensure we only try to dereference valid of_nodes
ASoC: rockchip-i2s: fix infinite loop in rockchip_snd_txctrl
ALSA: hda - Add dock port support to Thinkpad L440 (71aa:501e)
ALSA: Allow pass NULL dev for snd_pci_quirk_lookup()
ASoC: imx-es8328: Fix of_node_put() call with uninitialized object
ASoC: soc-pcm: fix sig_bits determination in soc_pcm_apply_msb()
ASoC: simple-card: Initialize headphone and mic GPIO numbers
ASoC: imx-es8328: Fix missing return code in imx_es8328_probe()
ALSA: hda - Add dock support for Thinkpad T440 (17aa:2212)
ALSA: usb: caiaq: check for cdev->n_streams > 1
ASoC: 88pm860x-codec: Fix possibly missing string termination
ASoC: core: fix use after free in snd_soc_remove_platform()
ASoC: soc-dapm: fix use after free
ALSA: hda - Make the inv dmic handling for Realtek use generic parser
ALSA: hda - Add Inverted Internal mic for Samsung Ativ book 9 (NP900X3G)
ALSA: hda - Add inverted internal mic for Asus Aspire 4830T
ASoC: Intel: byt-rt5640: fix coccinelle warnings
ASoC: fsl_esai doc: Add "fsl,vf610-esai" as compatible string
ASoC: da732x: Remove unnecessary KERN_ERR in pr_err()
ASoC: simple-card: Fix detect gpio documentation.
...
|
|
This patch fixes a failure to open PCM device with -ENOSYS in
Terratec Phase 88.
Terratec Phase 88 has two Selector Function Blocks of AVC Audio subunit
to switch source of clock. One is to switch internal/external for the
source and another is to switch word/spdif for the external clock.
The IDs for these Selector Function Blocks are 9 and 8. But in current
implementation they're 0 and 0.
Reported-by: András Murányi <muranyia@gmail.com>
Tested-by: András Murányi <muranyia@gmail.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.18
A few small fixes, mostly small although a few really nasty ones like
the interaction between GPIO 0 and simple-card.
|
|
'asoc/fix/imx', 'asoc/fix/mc13783', 'asoc/fix/rockchip' and 'asoc/fix/simple' into asoc-linus
|
|
|
|
|
|
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We can get into an infinite loop if the I2S_CLR register fails to
clear due to a missing break statement, so add that.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 3.18-rc1. Also in here is the PHY
tree, as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full
details in the changelog
All have been in the linux-next tree for a while with no issues"
* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
uas: Reduce number of function arguments for uas_alloc_foo functions
xhci: Allow xHCI drivers to be built as separate modules
xhci: Export symbols used by host-controller drivers
xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
xhci: Introduce xhci_init_driver()
usb: hcd: add generic PHY support
usb: rename phy to usb_phy in HCD
usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
USB: host: st: fix ehci/ohci driver selection
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: core: return -ENOTSUPP for all targeted hosts
USB: Remove .owner field for driver
usb: core: log higher level message on malformed LANGID descriptor
usb: Add LED triggers for USB activity
usb: Rename usb-common.c
usb: gadget: Refactor request completion
usb: gadget: Introduce usb_gadget_giveback_request()
usb: dwc2/gadget: move phy bus legth initialization
phy: remove .owner field for drivers using module_platform_driver
...
|
|
Yet another Thinkpad model that has a dock port.
Reported-by: Sascha Wilde <wilde@intevation.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a NULL check in snd_pci_quirk_lookup() so that NULL can be passed
as a pci_dev pointer. This fixes the possible NULL dereferences in
HD-audio drivers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The of_node_put() calls in imx_es8328_probe() may take uninitialized
pointers when reached though the early error path. This patch adds
the proper NULL initialization for fixing these.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the SNDRV_PCM_STREAM_CAPTURE branch in soc_pcm_apply_msb(), look at
sig_bits of the capture stream, not the playback one.
Spotted by coverity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
The uninitialized default of 0 for gpio_hp_det and gpio_mic_det doesn't
play well with asm-generic's gpio_is_valid():
static inline bool gpio_is_valid(int number)
{
return number >= 0 && number < ARCH_NR_GPIOS;
}
Hence on r8a7740/armadillo-legacy:
sh-mobile-hdmi sh-mobile-hdmi: SH Mobile HDMI Audio Codec
sh-mobile-hdmi sh-mobile-hdmi: ASoC: DAPM unknown pin Headphones
sh-mobile-hdmi sh-mobile-hdmi: ASoC: DAPM unknown pin Mic Jack
After that the kernel log is spammed ca. 7 times per second with:
sh-mobile-hdmi sh-mobile-hdmi: ASoC: DAPM unknown pin Headphones
Initialize the GPIO numbers with a negative number (-ENOENT) to fix this.
Fixes: 3fe240326cc395c6 ("ASoC: simple-card: Add mic and hp detect gpios.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
