| Age | Commit message (Collapse) | Author |
|---|
|
This is another attempt for the reduction of the latency at the start
of a USB audio playback stream. The first attempt in the commit
9ce650a75a3b caused an unexpected regression (a deadlock with pipewire
usage) and was later reverted by the commit 4b820e167bf6. The devils
are always living in details, of course; the cause of the deadlock was
the call of snd_pcm_period_elapsed() inside prepare_playback_urb()
callback. In the original code, this callback is never called from
the stream lock context as it's driven solely from the URB complete
callback. Along with the movement of the URB submission into the
trigger START, this prepare call may be also executed in the stream
lock context, hence it deadlocked with the another lock in
snd_pcm_period_elapsed(). (Note that this happens only conditionally
with a small period size that matches with the URB buffer length,
which was a reason I overlooked during my tests. Also, the problem
wasn't seen in the capture stream because the capture stream handles
the period-elapsed only at retire callback that isn't executed at the
trigger.)
If it were only about avoiding the deadlock, it'd be possible to use
snd_pcm_period_elapsed_under_stream_lock() as a solution. However, in
general, the period elapsed notification must be sent after the actual
stream start, and replacing the call wouldn't satisfy the pattern.
A better option is to delay the notification after the stream start
procedure finished, instead. In the case of USB framework, one of the
fitting place would be the complete callback of the first URB.
So, as a workaround of the deadlock and the order fixes above, in
addition to the re-applying the changes in the commit 9ce650a75a3,
this patch introduces a new flag indicating the delayed period-elapsed
handling and sets it under the possible deadlock condition
(i.e. prepare callback being called before subs->running is set).
Once when the flag is set, the period-elapsed call is handled at a
later URB complete call instead.
As a reference for the original motivation for the low-latency change,
I cite here again:
| USB-audio driver behaves a bit strangely for the playback stream --
| namely, it starts sending silent packets at PCM prepare state while
| the actual data is submitted at first when the trigger START is
| kicked off. This is a workaround for the behavior where URBs are
| processed too quickly at the beginning. That is, if we start
| submitting URBs at trigger START, the first few URBs will be
| immediately completed, and this would result in the immediate
| period-elapsed calls right after the start, which may confuse
| applications.
|
| OTOH, submitting the data after silent URBs would, of course, result
| in a certain delay of the actual data processing, and this is rather
| more serious problem on modern systems, in practice.
|
| This patch tries to revert the workaround and lets the URB
| submission starting at PCM trigger for the playback again. As far
| as I've tested with various backends (native ALSA, PA, JACK, PW), I
| haven't seen any problems (famous last words :)
|
| Note that the capture stream handling needs no such workaround,
| since the capture is driven per received URB.
Link: https://lore.kernel.org/r/4e71531f-4535-fd46-040e-506a3c256bbd@marcan.st
Link: https://lore.kernel.org/r/s5hbl7li0fe.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210707112447.27485-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix some spelling mistakes as follows:
altenate ==> alternate
compatbile ==> compatible
perfoms ==> performs
dont'register ==> don't register
periodicaly ==> periodically
arount ==> around
Signed-off-by: gushengxian <gushengxian@yulong.com>
Link: https://lore.kernel.org/r/20210705120052.665212-1-gushengxian507419@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix some spelling mistakes as follows:
wroong ==> wrong
evrything ==> everything
Signed-off-by: gushengxian <gushengxian@yulong.com>
Link: https://lore.kernel.org/r/20210705093419.664366-1-gushengxian507419@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This reverts commit 9ce650a75a3b262c90789b42aedee8fc2ee04d53.
This commit causes watchdog lockups on my machine, and while I have no
idea what the cause is, it bisected right to this commit, and reverting
the change promptly fixes it.
At least occasionally one of the watchdog call traces was
Call Trace:
_raw_spin_lock_irqsave+0x35/0x40
snd_pcm_period_elapsed+0x1b/0xa0 [snd_pcm]
snd_usb_endpoint_start+0x1a0/0x3c0 [snd_usb_audio]
start_endpoints+0x23/0x90 [snd_usb_audio]
snd_usb_substream_playback_trigger+0x7b/0x1a0 [snd_usb_audio]
snd_pcm_common_ioctl+0x1c44/0x2360 [snd_pcm]
snd_pcm_ioctl+0x2e/0x40 [snd_pcm]
__se_sys_ioctl+0x72/0xc0
do_syscall_64+0x4c/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xae
so presumably it's a locking error on that substream spinlock that
snd_pcm_period_elapsed() takes. But at this point I just want to have a
working system so that I can continue the merge window work tomorrow.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Clang warns:
sound/usb/mixer_scarlett_gen2.c:1189:32: warning: expression result
unused [-Wunused-value]
for (i = 0; i < count; i++, (u16 *)buf++)
^ ~~~~~
1 warning generated.
It appears the intention was to cast the void pointer to a u16 pointer
so that the data could be iterated through like an array of u16 values.
However, the cast happens after the increment because a cast is an
rvalue, whereas the post-increment operator only works on lvalues, so
the loop does not iterate as expected. This is not a bug in practice
because count is not greater than one at the moment but this could
change in the future so this should be fixed.
Replace the cast with a temporary variable of the proper type, which is
less error prone and fixes the iteration. Do the same thing for the
'u8 *' below this if block.
Fixes: ac34df733d2d ("ALSA: usb-audio: scarlett2: Update get_config to do endian conversion")
Link: https://github.com/ClangBuiltLinux/linux/issues/1408
Acked-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210627051202.1888250-1-nathan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Mixer control put callbacks should return 1 if the value is changed.
Fix the mute, air, phantom, direct monitor, speaker switch, talkback,
and MSD controls accordingly.
Fix scarlett2_speaker_switch_enable() to not ignore the return value
of scarlett2_sw_hw_change().
Reported-by: Aaron Wolf <aaron@wolftune.com>
Tested-by: Aaron Wolf <aaron@wolftune.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/76643f7ac81aef93351122d07881e30d51dcb1b9.1624798436.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The 18i8 Gen 3 has 4 inputs with a pad control, not 2. Update
s18i8_gen3_info.pad_input_count.
Reported-by: Aaron Wolf <aaron@wolftune.com>
Tested-by: Aaron Wolf <aaron@wolftune.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/29a6ce412a42373daab7c96c395560461fcf08c6.1624798436.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for the talkback feature of the 18i20 Gen 3.
Co-developed-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/e39599893a7479c290e1aaec6c79dcee87681b47.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For configuration items with a size of 16, scarlett2_usb_get_config()
was filling *buf with little-endian data. Update it to convert to CPU
endian. This function is not currently used so affects nothing yet;
will be used by the upcoming talkback feature.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/cbc8b6eedd859dd27086ab4126d724a86dd50bcb.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The 18i8 and 18i20 Gen 3 support "speaker switching". Add a Speaker
Switch control which can be set to Off/Main/Alt.
When speaker switching is enabled or disabled, the interface may
change the state of the Analog Outputs 3 and 4 routing and the global
mute button, so use a flag private->speaker_switching_switched to note
that those should be checked when the next "monitor other"
notification is received.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/874193a534cd0aeb6f2e108ae761cadd2dc25ad2.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Enabling/disabling speaker switching will update the mux
configuration. To prepare for this, add a private->mux_updated flag
and update the scarlett2_mux_src_enum_ctl_get() callback to check it.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/5ce3bb9fe4006b550d18c783c5ff640fe0bfbfcb.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Save the struct snd_kcontrol pointers for the sw_hw and mux controls.
This is in preparation for speaker switching support which needs to be
able to update those controls.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/269d89181bf29dbea80ba6f8cfff84fb23b77f86.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Split part of scarlett2_sw_hw_enum_ctl_put() out into
scarlett2_sw_hw_change() so that the code which actually makes the
change is available in its own function. This will be used by the
speaker switching support which needs to set the SW/HW switch to HW
when speaker switching is enabled.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/f2cf91841ba067b490e7709bc4b14f4532b4ddd5.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The 18i8 Gen 3 analogue 7/8 outputs are identified as line 3/4 on the
rear of the unit. Add support for remapping the channel numbers to
match the labelling.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/461acb911509e60e9ab48109ece3bbadae7440c8.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Solo and 2i2 devices don't have a mixer but they do have a "direct
monitor" switch. Add support for getting and setting the state of this
switch.
Co-developed-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/61d23dc4feb3b046d870ad7203e66ff2bd1d278c.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some inputs on Gen 3 models support software-selectable phantom power.
Add support for getting and setting the state of those switches and
the "Phantom Power Persistence" switch.
Co-developed-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/5837ce8a8c686560fc8f40b4204dd2a10721869b.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some inputs on Gen 3 models have an "air" feature which can be enabled
from the driver or (model-dependent) from the front panel. Add support
for getting and setting the state of those switches.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/44d448a4150b9c068754759c9fdd2bfe21484487.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add initial support for the Focusrite Scarlett Solo and 2i2 devices:
- They have no mixer
- They don't support reporting sync status or levels
- The configuration space is laid out differently to the other models
- There is no level (line/inst) switch on input 1 of the Solo
Co-developed-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/190b90f6f1f8f8d4dfb5f0a7761ff8ae5c40fdde.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for accessing configuration values when multiple values
are stored in one byte. Needed by the upcoming Solo and 2i2 Gen 3
support.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/4e54e9e106ec7029c1a668c51b4fc769a7eb4ed0.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move scarlett2_usb_get() and scarlett2_usb_get_config() above the
functions relating to updating the configuration so that
scarlett2_usb_set_config() can call scarlett2_usb_get() in a
subsequent patch.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/1549f8e44548be679119f0b1462f888f4a03812d.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a control to disable the Gen 3 MSD mode so that the full
functionality of the device is available. Don't create the other
controls until MSD mode is disabled.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/1cb93bbe585f6b0a74f5dc27450bc87e1f3776dc.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some models allow the level and pad settings to be controlled from the
front-panel of the device. For these, the device will send an
"input-other" notification to prompt the driver to re-read the status
of those settings.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/06289a7697455e96b7dbdfd2d384d4b20f8df6e0.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add mixer support for the Focusrite Scarlett 4i4, 8i6, 18i8, and 18i20
Gen 3 devices.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/22d0dc877dec026eb19630edec217ab72ebcd50a.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The current way of the scarlett2 mixer code managing the
usb_mixer_elem_info object is wrong in two ways: it passes its
internal index to the head.id field, and the val_type field is
uninitialized. This ended up with the wrong execution at the resume
because a bogus unit id is passed wrongly. Also, in the later code
extensions, we'll have more mixer elements, and passing the index will
overflow the unit id size (of 256).
This patch corrects those issues. It introduces a new value type,
USB_MIXER_BESPOKEN, which indicates a non-standard mixer element, and
use this type for all scarlett2 mixer elements, as well as
initializing the fixed unit id 0 for avoiding the overflow.
Tested-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/49721219f45b7e175e729b0d9d9c142fd8f4342a.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Level Meter control had a fixed number of channels and therefore
only worked with the 18i20 Gen 2. Fix the control to contain the
correct number of channels.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/5e9a2d5c136270db2d048db53a3b4b6e6d4a63de.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The scarlett2_ports struct contains both generic (hardware IDs and
descriptions) and model-specific (port count) data. Remove the generic
data from the scarlett2_device_info struct so it is not repeated for
every model.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/7a9e57e4e55a482390c692a9e60731d72b664a15.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some Gen 3 devices do not put all of the mux entries for the same port
types together in order in the "set mux" message data. To prepare for
this, replace the struct scarlett2_ports num[] array and the
assignment_order[] array with mux_assignment[], a list of port types
and ranges that is defined in the struct scarlett2_device_info.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/08e8d784d78262cb57496d28ef1ad7b6213a90ab.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For each analogue output, in addition to the output volume (gain)
control, the hardware also has a mute control. Add ALSA mute controls
for each analogue output.
If the device has the line_out_hw_vol feature, then the mute control
is disabled along with the output volume control when the switch is
set to HW.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/6fad82174b44633e46cfd96332a038de74d544f2.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add helper function for setting the read/write status of a volume
control. This will simplify the upcoming mute control support.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/00dd57e1abb3fa379fb51d4ac8537dbddc09f0ea.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Document the fields of struct scarlett2_device_info in the definition
of the struct, not in each instantiation.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/3486e4d38973333d4ec38f32578c16a9f97bf6c8.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The info variable is not used by snd_scarlett_gen2_init() except to
pass it to snd_scarlett_gen2_controls_create(), so move the lookup
into that function.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/c4b6d17708e104503d9a2b88f9b3320bb9904cfa.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add the USB device ID to the scarlett2_device_info struct so that the
switch statement which finds the appropriate struct can be replaced
with a loop that looks through an array of pointers to those structs.
Suggested-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/474c408c29fb280a611e47e49e59ca2fb9810d27.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use designated initializers and merge lines in preparation for more
configuration items coming soon.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/512d14eeb3571a266810c954d0f83140a3af7afc.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use a common sprintf() format for the mixer element names generated in
scarlett2_add_line_in_ctls() in preparation for more of them.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/d91dce45ac75a541c21f47540ecbda24bd83f68c.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add "Sync Status" control to display the sync locked/unlocked status.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/d6967d7a34b2ea7e0672ba819e4ed8b99e8dcd35.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Always enable interrupt polling as every model has some sort of
status to report.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/8f49a6b9a9805ee0db221706193b7bb43b7fff75.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are two headphone outputs, and they map to the four analogue
outputs.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/205e5e5348f08ded0cc4da5446f604d4b91db5bf.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The old initialisation code only works with Gen 2 devices. Replace it
with an initialisation sequence that works on both Gen 2 and Gen 3
devices.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/6e5c4fedb74b813872f6a4b7fba30b6c471fa63a.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull out snd_usb_ctl_msg() calls from scarlett2_usb() and put into
scarlett2_usb_tx() and scarlett2_usb_rx() functions.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/720d1d6f227fc8f5d7d6191a8de62db796940235.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
At extending the available mixer values for 32bit types, we forgot to
add the corresponding entries for the format dump in the proc output.
This may result in OOB access. Here adds the missing entries.
Fixes: bc18e31c3042 ("ALSA: usb-audio: Fix parameter block size for UAC2 control requests")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210622090647.14021-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove the hard-coded interface number and related constants for the
vendor-specific interface and look them up from the USB endpoint
descriptor.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164652.GA9237@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
scarlett2_usb_set_config() and scarlett2_usb_get_config() were copying
struct scarlett2_config. Use a pointer instead.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164648.GA9231@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix mixer control callbacks to use the correct members of the struct
snd_ctl_elem_value. The use of value.integer and value.enumerated were
swapped in a few places.
Update scarlett2_mux_src_enum_ctl_put() to use min() instead of
clamp() as value.enumerated.item is unsigned.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164647.GA9226@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Mixer control put callbacks should return 1 if the value is changed.
Fix the sw_hw, level, pad, and button controls accordingly.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164645.GA9221@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The private->vol_updated flag was being checked outside of the
mutex_lock/unlock() of private->data_mutex leading to the volume data
being fetched twice from the device unnecessarily or old volume data
being returned.
Update scarlett2_*_ctl_get() and include the private->vol_updated flag
check inside the critical region.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164643.GA9216@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add index temporary variable to scarlett2_mixer_ctl_put() for
consistency with the other *_ctl_put() functions.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164641.GA9211@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Rename struct scarlett2_mixer_data to struct scarlett2_data. A
less-wordy name is better because it is used everywhere, and although
this is a mixer driver, it also controls other vendor-specific
features.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164639.GA9206@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To match the vendor's terminology, change #defines, identifiers, and
comments:
- mute/dim/hardware buttons are now called dim/mute
- mixer status/interrupt is now notify
- vol is now monitor
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164636.GA9199@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The per-model button_count value was used to determine whether
dim/mute controls should be added, but these are present iff
line_out_hw_vol is true. Remove button_count and replace with
SCARLETT2_BUTTON_MAX and a check for line_out_hw_vol true.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164634.GA9193@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Just ignore instead of printing an error if the interrupt data is not
the expected length. This check was for development and the condition
has not been observed.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164632.GA9186@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
